Elucidation of Performance Recovery for Fe-Based Catalyst Cathodes in Fuel Cells
Not Available
25 ENERGY STORAGE↗
SEARCH · Engineering Papers
Results for “fuel cell cathode”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Topological Bismuth (1 1̅ 0) Facet for Efficient Oxygen Reduction Cathode in Fuel Cells
The performance of proton-exchange membrane fuel cells is strongly dependent on the efficiency of the electrochemical oxygen reduction reaction (ORR). Here, we report both two-dimensional (4 monolayer, ML) and three-dimensional Bi (16 ML) (11̅0) facets deliver a strong correlation between nontrivial topological surface states and low electrochemical overpotential toward ORR. Both topological Bi (11̅0) film and slab have two slightly gapped (9–45 meV) Dirac cones with the invariant Z 2 =1, derived from the parity products for the occupied states at four time-reversal invariant momentum points. By contrast, the Bi (110) film is stabilized as an ordinary insulator due to atomic buckling. The much lower thermodynamic ORR overpotential (η = 0.58 V) and higher H 2 O selectivity by four steps of H + /e – transfer are obtained on the topological Bi (11̅0) surface compared with the nontopological (110) facet (η = 0.84 V). This promotional effect can be attributed to the accumulation of topological surface bands (Bi 6p orbitals) near the Fermi energy, which provide stronger electronic transport channels along the surface Bi–Bi and Bi–O bonds. Finally, a 16 ML Bi (11̅0) slab is also constructed to simulate the topological (11̅0) surface of three-dimensional bulk Bi as a topological crystalline insulator (TCI). Furthermore, the consistent topological properties and slightly lower thermodynamic ORR overpotential (η = 0.53 V) are also observed on the thicker slab.
25 ENERGY STORAGE↗
Boosting solid oxide fuel cell performance via electrolyte thickness reduction and cathode infiltration
Increasing the power density and reducing the operating temperature of solid oxide fuel cells (SOFCs) is important for improving commercial viability. Here we discuss two strategies for achieving such improvements in Ni–YSZ supported SOFCs – electrolyte thickness reduction and cathode infiltration. Microstructural and electrochemical results are presented showing the effect of reducing YSZ/GDC electrolyte thickness from 8 to 2.5 μm, and the effect of PrO x infiltration into the LSCF–GDC cathode. Both of these measures are effective, particularly at lower temperatures, leading to an increase in the maximum power density at 650 °C from 0.4 to 0.95 W cm –2 , for example. Electrochemical impedance spectroscopy utilizing subtractive analysis shows that PrO x enhances the cathode charge transfer process. Reducing the electrolyte thickness reduces not only the cell ohmic resistance but also the electrode polarization resistance. Furthermore, the latter effect appears to be an artifact associated with a slight increase in the steam partial pressure at the anode due to minor gas leakage across the thinner electrolyte.
25 ENERGY STORAGE↗
Stabilizing platinum in phosphoric acid fuel cells
The cathode of the phosphoric acid fuel cell uses a high surface area platinum catalyst supported on a carbon substrate. During operation, the small platinum crystallites sinter, causing loss in cell performance. A support was developed that stabilizes platinum in the high surface area condition by retarding or preventing the sintering process. The approach is to form etch pits in the carbon by oxidizing the carbon in the presence of a metal oxide catalyst, remove the metal oxide by an acid wash, and then deposit platinum in these pits. Results confirm the formation of etch pits in each of the three supports chosen for investigation: Vulcan XC-72R, Vulcan XC-72 that was graphized at 2500 C, and Shawinigan Acetylene Black.
Remick, R. J.↗
Improved Cathode Structure for a Direct Methanol Fuel Cell
An improved cathode structure on a membrane/electrode assembly has been developed for a direct methanol fuel cell, in a continuing effort to realize practical power systems containing such fuel cells. This cathode structure is intended particularly to afford better cell performance at a low airflow rate. A membrane/electrode assembly of the type for which the improved cathode structure was developed (see Figure 1) is fabricated in a process that includes brush painting and spray coating of catalyst layers onto a polymer-electrolyte membrane and onto gas-diffusion backings that also act as current collectors. The aforementioned layers are then dried and hot-pressed together. When completed, the membrane/electrode assembly contains (1) an anode containing a fine metal black of Pt/Ru alloy, (2) a membrane made of Nafion 117 or equivalent (a perfluorosulfonic acid-based hydrophilic, proton-conducting ion-exchange polymer), (3) a cathode structure (in the present case, the improved cathode structure described below), and (4) the electrically conductive gas-diffusion backing layers, which are made of Toray 060(TradeMark)(or equivalent) carbon paper containing between 5 and 6 weight percent of poly(tetrafluoroethylene). The need for an improved cathode structure arises for the following reasons: In the design and operation of a fuel-cell power system, the airflow rate is a critical parameter that determines the overall efficiency, cell voltage, and power density. It is desirable to operate at a low airflow rate in order to obtain thermal and water balance and to minimize the size and mass of the system. The performances of membrane/electrode assemblies of prior design are limited at low airflow rates. Methanol crossover increases the required airflow rate. Hence, one way to reduce the required airflow rate is to reduce the effect of methanol crossover. Improvement of the cathode structure - in particular, addition of hydrophobic particles to the cathode - has been demonstrated to mitigate the effects of crossover and decrease the airflow required.
Valdez, Thomas↗
Mesoporous Textured Fe-N-C Electrocatalysts as Highly Efficient Cathodes for Proton Exchange Membrane Fuel Cells
A new platinum group metal (PGM)-free proton exchange membrane fuel cell (PEMFC) cathode catalyst materials, synthesized using the VariPore™ method by Pajarito Powder, LLC, are characterized for their structure and activity. The physico-chemical analysis of the iron-nitrogen-carbon (Fe-N-C) electrocatalysts show mesoporous carbon material effectively doped with iron and nitrogen. The materials have an average pore size of 7-8 nm and high specific surface area. The Fe-N-C catalysts exhibit good oxygen reduction reaction (ORR) activity in 0.5 M H2SO4 electrolyte with high half-wave potential and sustainable electrochemical stability over 10,000 repeated potential cycles with insignificant losses in their activities. As cathode catalysts in a PEMFC, the Fe-N-C materials deliver remarkably good fuel cell performance at low overpotential approaching that of the commercial Pt catalyst. The high ORR electrocatalytic activity of these Fe-N-C catalysts is credited to the synergy between nitrogen-moieties, specifically pyrrolic-N, pyridinic-N, and graphitic-N, and iron in addition to the high mesoporosity that facilitate an effective reaction path in boosting the electrocatalytic activity and stability.
DIRECT ENERGY CONVERSION↗
Design of Graded Cathode Catalyst Layers with Various Ionomers for Fuel Cell Application
Proton exchange membrane fuel cells (PEMFCs) powered by green hydrogen (H2) have become a promising alternative to conventional hydrocarbon-fueled power generators. Despite technological advancements, further improvements in efficiency, durability, and low-cost production are required for the widespread adoption of PEMFCs. Though numerous approaches to improve PEMFC electrodes have been reported, most strategies utilize a single material set (e.g., one combination of catalyst and ionomer) to improve performance. Alternatively, anisotropic (graded) electrode structures with locally tunable properties may yield superior electrode performance due to improved ionic and gas phase transport. In this work, graded cathode catalyst layers (CCLs) incorporating different ionomers (Nafion D2020, Aquivion D79-25BS, and HOPI) were designed and prepared. Performance screening shows that some of these graded electrode structures have comparable performance to optimized single-ionomer electrode structures (D2020) suggesting some synergistic benefit. Additionally, we show that electrodes with lower equivalent weight (EW) D79 ionomer near the membrane and D2020 ionomer near the gas diffusion media outperformed electrodes with the inverted configuration. Finally, EIS analysis shows some graded ionomer structures (e.g. D79/D2020) have better than expected H+ conductivity, generally leading to better electrode performance. However, further optimization of ionomer content and catalyst ink formulations is needed to improve overall PEMFC performance.
DIRECT ENERGY CONVERSION↗
Nanoscale Analysis of LSM/YSZ Interfaces within Composite Cathodes for Commercial Solid Oxide Fuel Cells
17th International Symposium on Solid Oxide Fuel Cells (SOFC-XVII), Virtual, July 18-23, 2021
Picard, Yoosuf↗
Investigating Effects of Operational Parameters on the Rate of Electrochemical Cleaning of Chromium Deposits on Strontium-Doped Lanthanum Manganite Cathodes in Solid Oxide Fuel Cells
Chromium poisoning of the cathode remains a significant obstacle to the stable long-term performance of solid oxide fuel cells. This study reports, a quick, in-situ mitigation method, called electrochemical cleaning. By applying a mild anodic bias, the electrochemical deposition reactions of chromium-containing species are reversed. Chromium vapor species are formed, freeing active electrochemical sites in the air electrode. An LSM/YSZ-based cell was exposed to Cr vapors at 800ºC and then subjected to electrochemical cleaning. Cell performance recovery was evidenced by current-voltage and EIS measurements. Chromium removal was verified using SEM and EDS analyses. The cyclability of the electrochemical cleaning was tested by repeated poisoning and cleaning of another cell. Investigation into the effect of cell operating parameters (current density and cell temperature) on the rate of cleaning is discussed.
30 DIRECT ENERGY CONVERSION↗
Ordered CoPt oxygen reduction catalyst with high performance and durability
A high-performance and durable polymer electrolyte membrane fuel cell cathode catalyst composed of an ordered L10–CoPt core and a thin Pt shell was designed and prepared. Under practical fuel cell membrane electrode assembly testing conditions, the cathode catalyst showed an outstanding initial mass activity of 0.6 A/mgPt, which satisfies the U.S. Department of Energy performance target while also meeting the durability target of less than 40% loss in mass activity after 30,000 accelerated stress test voltage cycles. The high structural stability of the L10–CoPt@Pt-shell catalyst was confirmed by postmortem materials characterization, and the origin of this robustness was revealed by density functional theory calculations, where the barriers for diffusion of Co atoms were observed to be significantly increased in the ordered intermetallic core.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Oxygen-hydrogen fuel cell with an iodine-iodide cathode - A concept
Fuel cell uses a porous cathode through which is fed a solution of iodine in aqueous iodide solution, the anode is a hydrogen electrode. No activation polarization appears on the cathode because of the high exchange-current density of the iodine-iodide electrode.
Javet, P.↗
Catalysts for ultrahigh current density oxygen cathodes for space fuel cell applications
The objective of this research was to identify promising electrocatalyst/support systems for the oxygen cathode in alkaline fuel cells operating at relatively high temperatures, O2 pressures and current densities. A number of materials were prepared, including Pb-Ru and Pb-Ir pyrochlores, RuO2 and Pt-doped RuO2, and lithiated NiO. Several of these were prepared using techniques that had not been previously used to prepare them. Particularly interesting is the use of the alkaline solution technique to prepare the Pt-doped Pb-Ru pyrochlore in high area form. Well-crystallized Pb(2)Ru(2)O(7-y) was used to fabricate high performance O2 cathodes with relatively good stability in room temperature KOH. This material was also found to be stable over a useful potential range at approximately 140 C in concentrated KOH. Other pyrochlores were found to be either unstable (amorphous samples) or the fabrication of the gas-fed electrodes could not be fully optimized during this project period. Future work may be directed at this problem. High area platinum supported on conductive metal oxide supports produced mixed results: small improvements in O2 reduction performance for Pb(2)Ru(2)O(7-y) but a large improvement for Li-doped NiO at room temperature. Nearly reversible behavior was observed for the O2/OH couple for Li-doped NiO at approximately 200 C.
Tryk, D.↗
Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells (Final Report)
The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co2O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Core-Shell Heterostructures as Functional Materials for Solid Oxide Fuel Cell (SOFC) Electrodes
The principal objective of this project was to synthesize core-shell heterostructures for solid oxide fuel cell cathodes using a molten salt solvent. In doing so, the main goals were split into a) to elucidate and understand the influence of molten salt chemistries to expeditiously synthesize perovskite type oxides for solid oxide fuel cells, b) provide a chemical framework for future molten salt syntheses of energy relevant ceramic materials, c) demonstrate and investigate the required parameters for the optimal core-shell synthesis and yield of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) – La 0.8 Sr 0.2 MnO 3 (shell), and d) demonstrate improved cathode performance of core-shell LSCF-LSM compared to an LSCF cathode on symmetric cells. The results clearly show that a) the influence of the molten salt cation outweighs the anion in regards to product stoichiometry, b) molten salts should be tailored to balance cationic and anionic acidity for high product yield, c) high yield of core-shell nanoparticles can be achieved by optimal mass ratio between core to shell, dwell time in the salt, size ratio between core to shell, and mass ratio between overall powder to salt, and d) the core-shell LSCF-LSM cathodes have lower polarization resistances than LSCF at higher temperatures. More work is required to optimize core-shell cathode performance at lower temperatures. However, this work thus provided justification for using the molten salt synthesis for SOFC cathodes and provided insights into future material modifications for improved performance.
08 HYDROGEN↗
Quantifying the electrochemical active site density of precious metal-free catalysts in situ in fuel cells
We report advances in the development of precious-group metal-free (PGM-free) catalysts for the oxygen reduction reaction (ORR) in fuel cell cathodes have produced active catalysts that reduce the performance gap to the incumbent Pt-based materials. However, utilization of state-of-the-art PGM-free catalysts for commercial applications is currently impeded by their relatively low durability. Methods designed to study catalyst degradation in the operation of fuel cells are therefore critical for understanding durability issues and, ultimately, their solutions. Here we report the use of Fourier-transform alternating current voltammetry as an electrochemical method for accurate quantification of the electrochemically active site density of PGM-free cathode catalysts, and to follow their degradation in situ during the operation of polymer electrolyte fuel cells. Using this method, we were able to quantify the electrochemical active site density, which will enable the elucidation of degradation mechanisms of PGM-free ORR catalysts in situ in fuel cells.
25 ENERGY STORAGE↗
Catalysts for ultrahigh current density oxygen cathodes for space fuel cell applications
The objective was to identify promising electrocatalyst/support systems for oxygen cathodes capable of operating at ultrahigh current densities in alkaline fuel cells. Such cells will require operation at relatively high temperatures and O2 pressures. A number of materials were prepared, including Pb-Ru and Pb-Ir pyrochlores, RuO2 and Pt-doped RuO2, lithiated NiO and La-Ni perovskites. Several of these materials were prepared using techniques that had not been previously used to prepare them. Particularly interesting was the use of the alkaline solution technique to prepare Pt-doped and Pb-Ru pyrochlores in high area form. Also interesting was the use of the fusion (melt) method for preparing the Pb-Ru pyrochlore. Several of the materials were also deposited with platinum. Well-crystallized Pb2Ru2O(7-y) was used to fabricate very high performance O2 cathodes with good stability in room temperature KOH. This material was also found to be stable over a useful potential range at approx. 140 C in concentrated KOH. For some of the samples, fabrication of the gas-fed electrodes could not be fully optimized during this project period. Future work may be directed at this problem. Pyrochlores that were not well-crystallized were found to be unstable in alkaline solution. Very good O2 reduction performance and stability were observed with Pb2RuO(7-y) in a carbon-based gas-fed electrode with an anion-conducting membrane placed on the electrolyte side of the electrode. The performance came within a factor of about two of that observed without carbon. High area platinum and gold supported on several conductive metal oxide supports were examined. Only small improvements in O2 reduction performance at room temperature were observed for Pb2Ru2O(7-y) as a support because of the high intrinsic activity of the pyrochlore. In contrast, a large improvement was observed for Li-doped NiO as a support for Pt. Very poor performance was observed for Au deposited on Li-NiO at approx. 150 C. Nearly reversible behavior was observed for the O2/OH(-) couple for Li-doped NiO at approx. 200 C. The temperature dependence for the O2 reduction was examined.
Tryk, Donald A.↗
Preparation and evaluation of advanced electrocatalysts for phosphoric acid fuel cells
The highest performance fuel cell cathode electrocatalyst combination ever observed gives 755 mV vs hydrogen at 100 ASF on air at 180 C and shows a potential improvement to 775 mV vs hydrogen for better electrode structures. A pressurized fuel cell (UTC at 5 atm) would then give 805 mV at 320 ASF and 180 C. Another activity diagnostic is the performance of this electrocatalyst on oxygen at 900 mV vs hydrogen. The value for electrocatalyst is 44 mA per milligram of platinum and is projected to reach 60 mA per milligram of platinum with improved electrode structures. Since the electrocatalyst surface area and the electrode structure are not yet optimized there is considerable room for performance enhancement beyond these values, especially at higher temperatures.
Stonehart, P.↗