SEARCH · Engineering Papers

Results for “free vortex wake”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1974

The Vortex Lattice Method for the Rotor-Vortex Interaction Problem

The rotor blade-vortex interaction problem and the resulting impulsive airloads which generate undesirable noise levels are discussed. A numerical lifting surface method to predict unsteady aerodynamic forces induced on a finite aspect ratio rectangular wing by a straight, free vortex placed at an arbitrary angle in a subsonic incompressible free stream is developed first. Using a rigid wake assumption, the wake vortices are assumed to move downsteam with the free steam velocity. Unsteady load distributions are obtained which compare favorably with the results of planar lifting surface theory. The vortex lattice method has been extended to a single bladed rotor operating at high advance ratios and encountering a free vortex from a fixed wing upstream of the rotor. The predicted unsteady load distributions on the model rotor blade are generally in agreement with the experimental results. This method has also been extended to full scale rotor flight cases in which vortex induced loads near the tip of a rotor blade were indicated. In both the model and the full scale rotor blade airload calculations a flat planar wake was assumed which is a good approximation at large advance ratios because the downwash is small in comparison to the free stream at large advance ratios. The large fluctuations in the measured airloads near the tip of the rotor blade on the advance side is predicted closely by the vortex lattice method.

Padakannaya, R.↗

NASA NTRS1998

Wake-Vortex Hazards During Cruise

Even though the hazard posed by lift-generated wakes of subsonic transport aircraft has been studied extensively for approach and departure at airports, only a small amount of effort has gone into the potential hazard at cruise altitude. This paper reports on a studio of the wake-vortex hazard during cruise because encounters may become more prevalent when free-flight becomes available and each aircraft, is free to choose its own route between destinations. In order to address the problem, the various fluid-dynamic stages that vortex wakes usually go through as they age will be described along with estimates of the potential hazard that each stage poses. It appears that a rolling-moment hazard can be just as severe at cruise as for approach at airports, but it only persists for several minutes. However, the hazard posed by the downwash in the wake due to the lift on the generator aircraft persists for tens of minutes in a long narrow region behind the generating aircraft. The hazard consists of severe vertical loads when an encountering aircraft crosses the wake. A technique for avoiding vortex wakes at cruise altitude will be described. To date the hazard posed by lift-generated vortex wakes and their persistence at cruise altitudes has been identified and subdivided into several tasks. Analyses of the loads to be encounter and are underway and should be completed shortly. A review of published literature on the subject has been nearly completed (see text) and photographs of vortex wakes at cruise altitudes have been taken and the various stages of decay have been identified. It remains to study and sort the photographs for those that best illustrate the various stages of decay after they are shed by subsonic transport aircraft at cruise altitudes. The present status of the analysis and the paper are described.

Rossow, Vernon J.↗

NASA NTRS1976

A subvortex technique for the close approach to a discretized vortex sheet

The close-approach problem associated with vortex-lattice methods was examined numerically with the objective of calculating velocities at arbitrary points, not just at midpoints, between the vortices. The objective was achieved using a subvortex technique in which a vortex splits into an increasing number of subvortices as it is approached. The technique, incorporated in a two-dimensional potential flow method using "submerged" vortices and sources, was evaluated for a cambered Joukowski airfoil. The method could be extended to three dimensions, and should improve non-linear methods, which calculate interference effects between multiple wings and vortex wakes, and which include procedures for force-free wakes.

Maskew, B.↗

NASA NTRS1985

Solution method for a hovering helicopter rotor using the Euler equations

A method for the calculation of the flow field of a helicopter rotor blade in hover is presented. The approach uses a finite volume solution of the three dimensional Euler equations for the blade near field. In the Euler solver the velocity field is decomposed into two parts. One is the induced velocity of the vortex wake extending below the blade, found from a free wake calculation procedure. The other part is the unknown additional velocity field of the rotor blade. This approach eliminates numerical diffusion of the rolled up wake vorticity due to truncation error and artificial viscosity. Also, the effects of the far wake are included in the limited computational domain. Solutions are presented for an isolated wing and a model helicopter rotor and compared to experiment.

Roberts, T. W.↗

NASA NTRS2000

Aircraft Spacings that Produce a Vortex-Free Region Below Flight Formation

Theoretical estimates are presented for the motion of vortex wakes shed by multiple aircraft flying in close formation. The purpose of the theoretical study was to determine whether the spacings between adjacent aircraft in close formations could be designed so that the lift-generated vortices being trailed would move upward rather than downward. In this way, a region below the formation is produced that is free of vortices. It was found that aircraft can be arranged in formations so that the inboard wake vortices all move upward rather than downward. The two outboard vortices travel downward at a greatly reduced velocity that depends on the number of aircraft in the formation. If the desired motions are to be produced, the lateral spacings between adjacent aircraft centerlines must be between 1.1 and 1.5 wingspans, and the vertical spacings between -0.025 and -0.15 wingspans. Since the range of acceptable spacings is small, it is recommended that the position accuracy between aircraft in the formation be kept within about + or - 0.01 wingspan of the center of acceptable spacings so that aircraft meandering do not cause unwanted vortex excursions. It was also found that, if the in-trail spacings between adjacent aircraft are more than 4 wingspans, the foregoing vertical spacings must be adjusted to allow for the additional downward travel of the vortices shed by leading aircraft.

Rossow, Vernon J.↗

NASA NTRS1994

Effect of ground and ceiling planes on shape of energized wakes

Results are presented from an investigation of the structure of energized wakes in the presence of ground or ceiling planes when powered-lift devices are tested at zero and low wind tunnel velocities. Solutions are presented to indicate how the presence of a nearby ground plane causes the energized wake to constrict less than when in free space. In contrast, another set of solutions indicate that the presence of a ceiling plane enhances wake construction so that the wake width is even smaller than when in free space. Hence, a ground plane tends to reduce the chance for interaction between the wake and the energizing elements, while a nearby ceiling plane tends to increase the likelihood for interference.

TRT-EXPERIMENTAL↗

NASA NTRS1985

Vortex wake alleviation studies with a variable twist wing

Vortex wake alleviation studies were conducted in a wind tunnel and a water towing tank using a multisegmented wing model which provided controlled and measured variations in span load. Fourteen model configurations are tested at a Reynolds number of one million and a lift coefficient of 0.6 in the Langley 4- by 7-Meter Tunnel and the Hydronautics Ship Model Basin water tank at Hydronautics, Inc., Laurel, Md. Detailed measurements of span load and wake velocities at one semispan downstream correlate well with each other, with inviscid predictions of span load and wake roll up, and with peak trailing-wing rolling moments measured in the far wake. Average trailing-wing rolling moments are found to be an unreliable indicator of vortex wake intensity because vortex meander does not scale between test facilities and free-air conditions. A tapered-span-load configuration, which exhibits little or no drag penalty, is shown to offer significant downstream wake alleviation to a small trailing wing. The greater downstream wake alleviation achieved with the addition of spoilers to a flapped-wing configuration is shown to result directly from the high incremental drag and turbulence associated with the spoilers and not from the span load alteration they cause.

Holbrook, G. T.↗

NASA NTRS1989

The prediction of loads on the Boeing Helicopters Model 360 rotor

Results are presented from a test/theory correlation investigation involving three rotor-analysis codes, two full potential rotor flow CFD solvers, and data obtained from tests on the Model 360 helicopter's rotor. Attention is given to the problem of reliable higher harmonic loading prediction. It is found that the rotor hover performance and loading experimental data are in excellent agreement with a novel, full potential free-wake computational technology; the need for a multiple tip-vortex wake model's use in predicting vibratory airloads is confirmed.

Dadone, Leo↗

NASA NTRS1993

Effect of ground and ceiling planes on shape of energized wakes

Energized wakes expelled by devices like thrust augmentors, propellers and rotors are studied theoretically in order to explore how their shape changes as they interact with ground and ceiling planes. It is found that when the airstream is stationary and the vehicle in hover, the presence of a ceiling plane causes an energized wake to constrict even more than when in an unbounded medium. The presence of a ground plane is found to cause the wake to constrict less than in free space. The computations also show that the vortex sheets first move inward before moving downward. Along their trajectory, the vortex sheets that separate the energized fluid from the ambient fluid have a nearly constant strength and velocity which indicates that the velocity just inside the wake is approximately constant. When a velocity is given to the wind tunnel airstream, the forward edge of the wake first rises and then descends so that it spends more time in the vicinity of the actuator disk. Implications of these results on measurements obtained in wind tunnels are discussed.

Rossow, Vernon J.↗

NASA NTRS1984

A computational method for helicopter vortex wakes

A method for calculating the wake geometry and blade loads for a hovering helicopter rotor is presented. The approach incorporates a simplified free wake model of the rotor in a finite difference calculation of the flow field. A variation of the 'cloud-in-cell' technique, modified to eliminate self-induced velocity errors for curved vortex filaments, is used. Simple lifting line theory is used to calculate the blade loads. Calculations showing the effect of vortex core size and the number of vortex filaments representing the wake are presented. For large numbers of vortices, it is seen that the wake geometry fails to converge. However, only a few vortices are needed to adequately represent the wake. Comparisons with experimental results are also presented.

Roberts, T. W.↗

NASA NTRS1976

Calculation of the longitudinal aerodynamic characteristics of wing-flap configurations with externally blown flaps

An analytical method for predicting the longitudinal aerodynamic characteristics of externally blown flap configurations is described. Two potential flow models make up the prediction method: a wing and flap lifting-surface model and a turbofan engine wake model. A vortex-lattice lifting-surface method is used to represent the wing and multiple-slotted trailing-edge flaps. The jet wake is represented by a series of closely spaced vortex rings normal to a centerline which is free to move to conform to the local flow field. The two potential models are combined in an iterative fashion to predict the jet wake interference effects on a typical EBF configuration. Comparisons of measured and predicted span-load distributions, individual surface forces, forces and moments on the complete configuration, and flow fields are included.

Mendenhall, M. R.↗

NASA NTRS1992

Computation of high resolution unsteady airloads using a constant vorticity contour free wake model

Recent work in the study of helicopter aerodynamic loading for acoustics applications has involved research on the development of an exceptionally efficient simulation of the velocity field induced by the rotor's vortex wake. This paper summarizes the work to date on the development of this analysis, which builds on the refined constant vorticity contour (CVC) free wake model recently developed for application to the study of vibratory loading. The particular focus of this paper is on demonstrations of a reconstruction approach that efficiently computes both the flow fields and airloads induced by CVC wakes on lifting rotor blades. Results of recent calculations on both main rotor and tail rotors are presented. These calculations show that by employing flow field reconstruction it is possible to apply the CVC wake analysis with temporal and spatial resolution suitable for acoustics applications while reducing the computation time required by one to two orders of magnitude relative to the direct calculations used in traditional methods.

Quackenbush, T. R.↗

NASA NTRS1990

Wake Geometry Effects on Rotor Blade-Vortex Interaction Noise Directivity

Acoustic measurements from a model rotor wind tunnel test are presented which show that the directionality of rotor blade vortex interaction (BVI) noise is strongly dependent on the rotor advance ratio and disk attitude. A rotor free wake analysis is used to show that the general locus of interactions on the rotor disk is also strongly dependent on advance ratio and disk attitude. A comparison of the changing directionality of the BVI noise with changes in the interaction locations shows that the strongest noise radiation occurs in the direction of motion normal to the blade span at the time of interaction, for both advancing and retreating side BVI. For advancing side interactions, the BVI radiation angle down from the tip-path plane appears relatively insensitive to rotor operating condition and is typically between 40 and 55 deg below the disk. However, the azimuthal radiation direction shows a clear trend with descent speed, moving towards the right of the flight path with increasing descent speed. The movement of the strongest radiation direction is attributed to the movement of the interaction locations on the rotor disk with increasing descent speed.

Martin, R. M.↗

NASA NTRS1986

Formal optimization of hovering performance using free wake lifting surface theory

Free wake techniques for performance prediction and optimization of hovering rotor are discussed. The influence functions due to vortex ring, vortex cylinder, and source or vortex sheets are presented. The vortex core sizes of rotor wake vortices are calculated and their importance is discussed. Lifting body theory for finite thickness body is developed for pressure calculation, and hence performance prediction of hovering rotors. Numerical optimization technique based on free wake lifting line theory is presented and discussed. It is demonstrated that formal optimization can be used with the implicit and nonlinear objective or cost function such as the performance of hovering rotors as used in this report.

Chung, S. Y.↗

NASA NTRS1982

Flows over wings with leading-edge vortex separation

The unsteady cross flow analogy reduces the steady three dimensional separation flow problem into an unsteady two dimensional flow problem in which the section shape changes with time. The two dimensional VORSEP code is extended to the case of arbitrary body growth rates in order to generate the initial vortex structures for the three dimensional free vortex sheet (FVS) code. Automatic procedures to reduce the wing geometry definition to a set of cross flow plane sections corresponding to the locations of the time step solutions and to generate the effective source distribution on each cross flow section to represent the section normal growth across the following steps are incorporated in the VORSEP code. Also, the wake shedding model is improved by adopting a redistribution scheme which improves the stability of the free sheet development with time. The improved wake shedding model combined with the redistribution scheme alleviated the numerical instabilities associated with the vortex rollup.

Rao, B. M.↗

NASA NTRS1977

A numerical method for the exact calculation of airloads associated with impulsively started wings

A numerical method is developed to calculate three-dimensional potential flows due to the steady and impulsive motion of isolated wing and wing-wing interaction problems. The velocity potential is represented by a discrete set of constant-doublet quadrilaterals on wing and wake surfaces. The exact surface boundary condition is enforced, and the solution is obtained in a step-by-step fashion, configurations being impulsively started from rest. Free-wake geometries are generated for each time step with Rankine or Lamb viscous vortex segments used in wake-velocity calculations. Sample results include calculated performance to steady state for a thick wing and indicial lift of a wing-wing interaction problem.

Summa, J. M.↗

NASA NTRS1982

Unsteady rotor aerodynamics using a vortex panel method

The problem of the potential incompressible flow about a helicopter rotor blade is solved using an unsteady vortex-panel method where the mutual interaction between the blade and the distorting free wake is taken into account. The present method alleviates the need to rely upon measured-wake geometries or p5escribed-wake models in order to calculate the airloads. A computer program has been developed which is capable of predicting the geometry of the time-dependent three-dimensional (3-D) wake and the instantaneous loadings for a single blade in hover, climb, and forward flight. The solution is obtained by using a time-accurate step-by-step procedure. The complex-wake geometry at any time is presented graphically with a computer graphics system. Calculated results are compared with published data for a rotor blade in both hover and forward flight. The code has also been applied to the study of the effect of changing blade tip geometry.

Crispin, Y.↗

NASA NTRS1980

Comparison of calculated and measured model rotor loading and wake geometry

The calculated blade bound circulation and wake geometry are compared with measured results for a model helicopter rotor in hover and forward flight. Hover results are presented for rectangular tip and ogee tip planform blades. The correlation is quite good when the measured wake geometry characteristics are used in the analysis. Available prescribed wake geometry models are found to give fair predictions of the loading, but they do not produce a reasonable prediction of the induced power. Forward flight results are presented for twisted and untwisted blades. Fair correlation between measurements and calculations is found for the bound circulation distribution on the advancing side. The tip vortex geometry in the vicinity of the advancing blade in forward flight was predicted well by the free wake calculation used, although the wake geometry did not have a significant influence on the calculated loading and performance for the cases considered.

Johnson, W.↗