Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “formaldehyde”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

A survey of formaldehyde in high Galactic latitudes

The discovery of formaldehyde (H2CO) in four out of 15 CO-clouds observed in high Galactic latitudes is reported. For one of these a velocity-integrated formaldehyde map is presented. The clouds are clearly connected to CO clouds described by de Vries et al. (1986), to Lynds bright and dark nebulae (Lynds, 1963), and to the Galactic infrared cirrus (Low et al., 1984). The distribution of CO and H2CO clouds is compared. The depths of the l(10-11)H2CO lines show no correlation to the integrated J = l-0(C-12)O line intensities.

Heithausen, A.↗
NASA NTRS1990

Observations of formaldehyde in Comet Machholtz (1988j)

Comet Machholtz's 1(11)-1(10) formaldehyde emission was detected with the VLA in September, 1988 at 6-cm wavelength; the small blueshift of -0.76 + or - 0.40 km/sec noted by these observations is consistent with an anisotropic outgassing of the cometary nucleus in the solar direction. The derived formaldehyde production rate for Comet Halley, which exhibits a similar emission line blueshift, was 1.5 x 10 to the 28th mol/sec, while for Comet Machholtz the production rate is about an order of magnitude higher, at 2 x 10 to the 29th mol/sec. The fading of Comet Machholtz after these observations is ascribed to its breakup.

Snyder, Lewis E.↗
NASA NTRS1990

VLA searches for formaldehyde and cyanoacetylene emission from comet P/Brorsen-Metcalf (1989o)

In Sep. 1989, Very Large Array (VLA) searches were conducted for both formaldehyde (H2CO) and cyanoacetylene (HC3N) emission from Comet P/Brorsen-Metcalf (1989o). In early July, this comet was outgassing strongly at a brighter than average preperihelion rate, and the hope was that it would continue to do so through perihelion. By observing the 1 sub 11 to 1 sub 10 transition of H2CO at 4,829.659 MHz (6 cm lambda) during the phase of maximum outgassing, it was expected that spectra would be collected with a high signal to noise ratio which would show the temporal behavior of formaldehyde relative to other molecules. During this same observation period, a search was also made for the J-1-0, F-2-1 rotational transition of cyanoacetylene at 9098.3321 MHz (3.3 cm lambda).

Snyder, Lewis E.↗
NASA NTRS1991

Collisional excitation of formaldehyde in 'hot' interstellar molecular regions

Earlier calculations for rotational excitation of formaldehyde by collisions with He atoms are extended to include the lowest 81 rotational levels and kinetic temperatures to 300 K. Calculations are generally based on Green et al. (1978) but coupled differential equations are solved via a modified log-derivative propagator at low energies (Manolopoulos, 1986) and an R-matrix propagator at higher energies (Stechel, Walker, and Light, 1978). Consideration is given to the expected accuracy of the rates for excitation of formaldehyde by collisions with He atoms which are calculated in the present paper and to the expected differences between these rates and those for excitation by H2 molecules which comprise a larger fraction of the interstellar gas. The comparisons performed indicate that, for excitation by He, calculated state-to-state rates are likely to be 50 percent accurate, and total excitation rates, better than 20 percent. For excitation by H2, the rates should be increased by a factor of 2.2.

Green, Sheldon↗
NASA NTRS1991

Formaldehyde in envelopes of interstellar dark clouds

Observed formaldehyde column densities of 1 x 10 to the 12th - 3 x 10 to the 13th/sq cm in cloud envelopes along lines of sight with A(V) = 1-4 mag can not be explained with the current understanding of interstellar gas phase chemistry. However, these column densities can be reproduced by a simple time-dependent model in which H2CO is supplied to the gas phase by the erosion of icy grain mantles. The release of H2CO from the grain mantles must occur on time scales comparable to the time scales for mixing from the cloud interior to the cloud envelope. Thus, in low-density regions of clouds, it appears that formaldehyde is the second molecule whose gas phase source is primarily ejection from grains. This simple model suggests understanding gas phase steady state in clouds on macroscopic, rather than microscopic, spatial scales.

Federman, S. R.↗
NASA NTRS1991

Sources and geochemical evolution of cyanide and formaldehyde

The major source of cyanide has, in current paleoatmospheric models, been assumed to be the reaction of photodissociated thermospheric nitrogen with a limiting supply of stratospheric methane. Formaldehyde may be produced with more ease from an atmosphere of carbon dioxide as the dominant carbon species, and from carbonate in solution or sorbed in double layer hydroxide minerals. Potentially more important sources for cyanide and other carbon containing molecules are the partially photoprotected northern and southern auroral ovals where continuous currents reaching several mega-amperes induce ion-molecule reactions, extending into the lower stratosphere. In simulated environments of this kind, the cyanide ion is known to be produced from oxidized carbon species potentially more abundant than methane. Rainout of cyanide and formaldehyde place them in two different geochemical reaction reservoirs. In the anoxic Archean hydrosphere, about 1mM in Fe2(+), the cyanide ion would have been efficiently converted to the stable ferrocyanide complex Fe(CN) sub 6(4-), protecting it from the commonly considered fate of decomposition by hydrolysis, and eventually incorporating it in pyroaurite type minerals, most efficiently in green rust where it converts to insoluble ferriferrocyanide, prussian blue.

Arrhenius, G.↗
NASA NTRS1995

Very low temperature formaldehyde reactions and the build-up of organic molecules in comets and interstellar ices

We have investigated thermally promoted reactions of formaldehyde (H2CO) in very low temperature ices. No such reactions occurred in ices of pure formaldehyde. However, addition of trace amounts of ammonia (NH3) were sufficient to catalyze reactions at temperatures as low as 40 K. Similar reactions could take place in interstellar ices and in Comets and produce considerable amounts of organic molecules.

Schutte, W. A.↗
NASA NTRS1993

Tentative identification of formaldehyde in the Martian atmosphere

Solar occultation observations of the Martian atmosphere near the limb of the planet were performed during the Phobos mission by means of the Auguste infrared spectrometer in the ranges 2707-2740 and 5392-5272/cm with a resolving power of approximately = 1300. The spectra exhibit features at 2710 and 2730/cm which have not been identified previously. After applying a set of corrections to the data and examining the spectra of various molecules, we are led to conclude that the best candidate for the above-mentioned features is formaldehyde (CH2O). It was observed in eight of the nine successful occultation sequences, mainly between 8 and 20 km with an average mixing ratio of 0.5 (+0.8, - 0.3) ppm (there are no good data below 8 km). The observations are performed in equatorial spring conditions. The altitude distribution of formaldehyde reveals correlation with the permanent haze opacity.

Korablev, O. I.↗
NASA NTRS2001

Ambient formaldehyde detection with a laser spectrometer based on difference-frequency generation in PPLN

A laser spectrometer based on difference-frequency generation in periodically poled LiNbO3 (PPLN) has been used to quantify atmospheric formaldehyde with a detection limit of 0.32 parts per billion in a given volume (ppbV) using specifically developed data-processing techniques. With state-of-the-art fiber-coupled diode-laser pump sources at 1083 nm and 1561 nm, difference-frequency radiation has been generated in the 3.53-micrometers (2832-cm-1) spectral region. Formaldehyde in ambient air in the 1- to 10-ppb V range has been detected continuously for nine and five days at two separate field sites in the Greater Houston area operated by the Texas Natural Resource Conservation Commission (TNRCC) and the Houston Regional Monitoring Corporation (HRM). The acquired spectroscopic data are compared with results obtained by a well-established wet-chemical o-(2,3,4,5,6-pentafluorobenzyl) hydroxylamine (PFBHA) technique.

NASA Discipline Life Sciences Technologies↗
NASA NTRS2011

A Hollow-Waveguide Gas Correlation Radiometer for Ultra-Precise Column Measurements of Formaldehyde on Mars

We present preliminary results in the development of a miniaturized gas correlation radiometer that implements a hollow-core optical fiber (hollow waveguide) gas correlation cell. The substantial reduction in mass and volume of the gas correlation cell makes this technology appropriate for an orbital mission -- capable of pinpointing sources of trace gases in the Martian atmosphere. Here we demonstrate a formaldehyde (H2CO) sensor and report a detection limit equivalent to approximately 30 ppb in the Martian atmosphere. The relative simplicity of the technique allows it to be expanded to measure a range of atmospheric trace gases of interest on Mars such as methane (CH4), water vapour (H2O), deuterated water vapour (HDO), and methanol (CH3OH). Performance of a formaldehyde instrument in a Mars orbit has been simulated assuming a 3 meter long, 1000 micron inner diameter hollow-core fiber gas correlation cell, a 92.8 degree sun-synchronous orbit from 400 km with a horizontal sampling scale of 10 km x 10 km. Initial results indicate that for one second of averaging, a detection limit of 1 ppb is possible.

Wilson, Emily L.↗
NASA NTRS2013

Toxicological Assessment of ISS Air Quality: September 2012 - October 2012 with Formaldehyde Supplement from May-October 2012

A summary of the analytical results from 6 grab sample containers (GSCs) and 12 pairs of formaldehyde badges collected on ISS and returned aboard 29S or 31 S is shown in an accompanying table. The average recoveries of the 3 surrogate standards from the GSCs were as follows: C-l3-acetone, 128%; fluorobenzene, 114%; and chlorobenzene, 78%. Recoveries of two lab-control formaldehyde badges averaged 95%.

James, John T.↗
NASA NTRS2015

Adsorption of Carbon Dioxide, Ammonia, Formaldehyde, and Water Vapor on Regenerable Carbon Sorbents

Results are presented on the development of reversible sorbents for the combined carbon dioxide, moisture, and trace‐contaminant (TC) removal for use in Extravehicular Activities (EVAs), and more specifically in the Primary Life Support System (PLSS). The currently available life support systems use separate units for carbon dioxide, trace contaminants, and moisture control, and the long‐term objective is to replace the above three modules with a single one. Furthermore, the current TC‐control technology involves the use of a packed bed of acid‐impregnated granular charcoal, which is nonregenerable, and the carbon‐based sorbent under development in this project can be regenerated by exposure to vacuum at room temperature. In this study, several carbon sorbents were fabricated and tested for simultaneous carbon dioxide, ammonia, formaldehyde, and water sorption. Multiple adsorption/vacuum‐regeneration cycles were demonstrated at room temperature, and also the enhancement of formaldehyde sorption by the presence of ammonia in the gas mixture.

Wojtowicz, Marek A.↗
NASA NTRS2017

A New Non-Resonant Laser-Induced Fluorescence Instrument for the Airborne in Situ Measurement of Formaldehyde

A new in situ instrument for gas-phase formaldehyde (HCHO), COmpact Formaldehyde FluorescencE Experiment (COFFEE), is presented. COFFEE utilizes nonresonant laser-induced fluorescence (NR-LIF) to measure HCHO, with 300 mW of 40 kHz 355 nm laser output exciting multiple HCHO absorption features. The resulting HCHO fluorescence is collected at 5 ns resolution, and the fluorescence time profile is fit to yield the ambient HCHO mixing ratio. Typical 1 sigma precision at approximately 0 pptv HCHO is 150 pptv for 1 s data. The compact instrument was designed to operate with minimal in-flight operator interaction and infrequent maintenance (1-2 times per year). COFFEE fits in the wing pod of the Alpha Jet stationed at the NASA Ames Research Center and has successfully collected HCHO data on 27 flights through 2017 March. The frequent flights, combined with a potentially long-term data set, makes the Alpha Jet a promising platform for validation of satellite-based column HCHO.

Nonresonant laser-induced fluorescenc↗
NASA NTRS2023

Development of a Photoacoustic Formaldehyde Monitor

Key indoor air quality pollutant formaldehyde (H2CO) is tracked on International Space Station (ISS) using passive badges returned to the ground periodically for analysis. The process is time-consuming both in preparation and for analysis upon return 6-12 months later. Badges also require precious crew time for deploy, retrieval and stow. As NASA’s focus in space exploration shifts to the Moon and Mars, archival sample return becomes increasingly impractical, so the aim of this project is to develop a highly reliable real-time analyzer for H2CO at low concentrations with data downlinked. Potential sources of H2CO include materials off gassing, use of formalin as a tissue fixative in biological payloads and overheating of acetal polymers. The Spacecraft Maximum Allowable Concentration (SMAC) for H2CO is 100 ppb for exposures of 7 days or longer. ISS concentrations recently run only 10 - 30 ppb but have spiked as high as 60 ppb in the past. Gateway real time monitoring requirements call for a range of 8 - 140 ppb. For this project, a concentration range of 5 - 500 ppb H2CO is targeted. The core tunable diode laser spectroscopy (TDLS) technology was developed by Vista Photonics through the NASA and US Navy Small Business Innovation Research (SBIR) programs. Monitors based on this technology have been demonstrated on ISS, trialed on a nuclear submarine and are in production as Anomaly Gas Analyzers for both ISS and Orion. Initially, direct absorption TDLS was used exclusively in these monitors, however, the H2CO target concentration is much lower, and a longer wavelength required, so a photoacoustic spectroscopy (PAS) technique was adapted, where the laser excitation is detected by a sensitive microphone vs. a conventional photodetector. This paper will discuss the results of NASA-JSC laboratory testing of a prototype PAS based formaldehyde monitor and explore potential adaptations for Gateway missions and beyond.

Paul D Mudgett↗
NASA NTRSDate not supplied

A21I-1875: Leveraging TEMPO Formaldehyde Observations to Assess Surface Air Quality

Surface ozone (O3) pollution is detrimental to human health, crop yields, and ecosystem productivity. Ground-based ozone observations are sparse and surface ozone retrievals from space are challenging. The process of producing ozone from the oxidation of volatile organic compounds (VOCs) in the presence of nitrogen oxides (NOx) results in formaldehyde (HCHO), which can be observed from satellite and by surface-based remote sensing. From limited field campaign observations, column formaldehyde has been shown to exhibit a strong relationship with surface ozone and, therefore, could be an useful proxy for detecting unmonitored regions of elevated ozone pollution. The spatiotemporal characteristics of this relationship are explored using ground-based Pandora spectrometers and airborne remote sensing data with surface ozone monitors across the United States during recent field campaigns over major cities (TRACER-AQ and STAQS). We extend our analysis to take advantage of HCHO column observations from recently launched Tropospheric Emissions: Monitoring of Pollution (TEMPO), a geostationary satellite over North America. TEMPO observations show preliminary promise in mapping regions of elevated surface ozone from space using column HCHO. We demonstrate the use of column HCHO in assessing the strength of the surface monitoring network, and in detecting the extent of regional ozone exceedances.

Prajjwal Rawat↗