Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow-through”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

The design of a wind tunnel VSTOL fighter model incorporating turbine powered engine simulators

A wind-tunnel model of a supersonic VSTOL fighter aircraft configuration has been developed for use in the evaluation of airframe-propulsion system aerodynamic interactions. The model may be employed with conventional test techniques, where configuration aerodynamics are measured in a flow-through mode and incremental nozzle-airframe interactions are measured in a jet-effects mode, and with the Compact Multimission Aircraft Propulsion Simulator which is capable of the simultaneous simulation of inlet and exhaust nozzle flow fields so as to allow the evaluation of the extent of inlet and nozzle flow field coupling. The basic configuration of the twin-engine model has a geometrically close-coupled canard and wing, and a moderately short nacelle with nonaxisymmetric vectorable exhaust nozzles near the wing trailing edge, and may be converted to a canardless configuration with an extremely short nacelle. Testing is planned to begin in the summer of 1982.

Bailey, R. O.↗
NASA NTRS1983

Three-dimensional Euler solutions for long-duct nacelles

A three-dimensional Euler-equation computational technique has been developed to solve for the transonic flow past flow-through nacelles. The technique employs an approximately-factored alternating-direction implicit numerical algorithm and a radiation treatment of the outflow boundary. Studies are presented which show that the radiation treatment gives better numerical convergence than the condition of specifying the pressure at the outflow boundary. Calculations made with the technique are presented for a long-duct turbofan engine nacelle at a Mach number of 0.80 and angles of attack of 0 deg and 4 deg. Good agreement is shown between the computational results and wind-tunnel data. Problem areas are identified and recommendations are made for further numerical studies.

Compton, W. B., III↗
NASA NTRS1984

An experimental investigation of nacelle-pylon installation on an unswept wing at subsonic and transonic speeds

A wind tunnel investigation was conducted to determine the aerodynamic interference associated with the installation of a long duct, flow-through nacelle on a straight unswept untapered supercritical wing. Experimental data was obtained for the verification of computational prediction techniques. The model was tested in the 16-Foot Transonic Tunnel at Mach numbers from 0.20 to 0.875 and at angles of attack from about 0 deg to 5 deg. The results of the investigation show that strong viscous and compressibility effects are present at the transonic Mach numbers. Numerical comparisons show that linear theory is adequate for subsonic Mach number flow prediction, but is inadequate for prediction of the extreme flow conditions that exist at the transonic Mach numbers.

Carlson, J. R.↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1985

Nacelle/pylon/wing integration on a transport model with a natural laminar flow nacelle

Tests were conducted in the Langley 16-Foot Transonic Tunnel at free-stream Mach numbers from 0.70 to 0.82 and angles of attack from -2.5 deg to 4.0 deg to determine if nacelle/pylon/wing integration affects the achievement of natural laminar flow on a long-duct flow-through nacelle for a high-wing transonic transport configuration. In order to fully assess the integration effect on a nacelle designed to achieve laminar flow, the effects of fixed and free nacelle transitions as well as nacelle longitudinal position and pylon contouring were obtained. The results indicate that the ability to achieve laminar flow on the nacelle is not significantly altered by nacelle/pylon/wing integration. The increment in installed drag between free and fixed transition for the nacelles on symmetrical pylons is essentially the calculated differences between turbulent and laminar flow on the nacelles. The installed drag of the contoured pylon is less than that of the symmetrical pylon. The installed drag for the nacelles in a rearward position is greater than that for the nacelles in a forward position.

Lamb, M.↗
NASA NTRS1986

Aerodynamic Characteristics of a Supersonic Fighter Aircraft Model at Mach 0.40 to 2.47

The aerodynamic characteristics of an advanced twin-engine fighter aircraft designed for supersonic cruise have been studied in the Langley 16-Foot Transonic Tunnel and the Lewis 10- by 10-Foot Supersonic Tunnel. The objective of this investigation was to establish an aerodynamic data base for the configuration with flow-through nacelles and representative inlets. The use of a canard for trim and the effects of fairing over the inlets were assessed. Comparisons between experimental and theoretical results were also made. The theoretical results were determined by using a potential vortex lift code for subsonic speeds and a linear aerodynamic code for supersonic speeds. This investigation was conducted at Mach numbers from 0.40 to 2.47, at angles of attack from 0 deg to about 20 deg, and at inlet capture ratios of about 0.5 to 1.4.

Capone, F. J.↗
NASA NTRS1986

Effects of upper-surface nacelles on longitudinal aerodynamic characteristics of high-wing transport configuration

An investigation has been conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of installing and streamline contouring upper-surface nacelles on the longitudinal aerodynamic characteristics of a high-wing transport configuration. Also investigated were the effects of adding a fairing under the nacelle. The investigation was conducted at free-stream Mach numbers from 0.60 to 0.83 at angles fo attack from -2 deg to 4 deg. Flow-through nacelles were used. Streamline contouring the nacelles substantially reduced the interference drag due to installing the nacelles.

Putnam, L. E.↗
NASA NTRS1985

Propulsion and airframe aerodynamic interactions of supersonic V/STOL configurations, phase 1

A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to present two different test techniques. One was a coventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a subscale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously.

Mraz, M. R.↗
NASA NTRS1986

PAN AIR analysis of the NASA/MCAIR 279-3: An advanced supersonic V/STOL fighter/attack aircraft

PAN AIR is a computer program for predicting subsonic or supersonic linear potential flow about arbitrary configurations. The program was applied to a highly complex single-engine-cruise V/STOL fighter/attack aircraft. Complexities include a close-coupled canard/wing, large inlets, and four exhaust nozzles mounted directly under the wing and against the fuselage. Modeling uncertainties involving canard wake location and flow-through approximation through the inlet and the exhaust nozzles were investigated. The recently added streamline capability of the program was utilized to evaluate visually the predicted flow over the model. PAN AIR results for Mach numbers of 0.6, 0.9, and angles of attack of 0, 5, and 10 deg. were compared with data obtained in the Ames 11- by 11-Foot Transonic Wind tunnel, at a Reynolds number of 3.69 x 10 to the 6th power based on c bar.

Madson, Michael D.↗
NASA NTRS1987

Recent developments in water quality monitoring for Space Station reclaimed wastewaters

This paper discusses the recent developments in water quality monitoring for Space Station reclaimed wastewaters. A preprototype unit that contains an ultraviolet absorbance organic carbon monitor integrated with pH and conductivity sensors is presented. The preprototype has provisions for automated operation and is a reagentless flow-through system without any gas/liquid interfaces. The organic carbon monitor detects by utraviolet absorbance the organic impurities in reclaimed wastewater which may be correlated to the organic carbon content of the water. A comparison of the preprototype organic carbon detection values with actual total organic carbon measurements is presented. The electrolyte double junction concept for the pH sensor and fixed electrodes for both the pH and conductivity sensors are discussed. In addition, the development of a reagentless organic carbon analyzer that incorporates ultraviolet oxidation and infrared detection is presented. Detection sensitivities, hardware development, and operation are included.

Small, John W.↗
NASA NTRS1987

Supersonic flow computations over aerospace configurations using an Euler marching solver

For fully supersonic flows, an efficient strategy for obtaining numerical solutions is to employ space marching techniques. A full potential marching technique, known as the SIMP code and capable of handling such embedded subsonic regions, has achieved some success analyzing low supersonic Mach number flows. The extension of the full potential approach to the Euler equation which model the exact nonlinear inviscid gas dynamic flow processes is presented. Within the assumption of an inviscid flow, such an Euler marching solver can be applied to a wide class of shocked flows including the hypersonic range. The intent is to maintain some of the basic features of the full potential SIMP code within the Euler solver in dealing with geometry input, gridding techniques, and input/output routines including post processing of results. An Euler marching code known as EMTAC was developed. Results obtained for a variety of configurations involving canard, wing, horizontal tail, flow-through inlet, and fuselage using both the EMTAC and SIMP codes are reported. For shocked cases satisfying the isentropic assumption, the EMTAC and SIMP codes produced practically the same results. In terms of execution time, the EMTAC code is slower.

Szema, Kuo-Yen↗
NASA NTRS1990

HgI2 low energy beta particle detector

An HgI2 device structure was designed and tested which allows HgI2 to be used to make low-energy beta-particle detectors. The devices detected tritium beta particles with an efficiency of about 25 percent. A protective encapsulant has been developed which should protect the devices for up to 20 years and will attenuate only a small fraction of the beta particles. It is noted that the devices hold significant promise to provide a practical alternative to liquid scintillation counters and gas flow-through proportional counters.

Shah, K. S.↗
NASA NTRS1990

Effect of location of aft-mounted nacelles on the longitudinal aerodynamic characteristics of a high-wing transport airplane

As part of a propulsion/airframe integration program at Langley Research Center, tests were conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of locating flow-through mixed flow engine nacelles in several aft underwing positions on the longitudinal aerodynamics of a high wing transport airplane. D-shaped inlet nacelles were used in the test. Some configurations with antishock bodies and with nacelle toe-in were also tested. Data were obtained for a free stream Mach number range of 0.70 to 0.85 and a model angle-of-attack range from -2.5 to 4.0 degrees.

Abeyounis, William K.↗
NASA NTRS1989

Wind tunnel balance

A flow-through balance is provided which includes a non-metric portion and a metric portion which form a fluid-conducting passage in fluid communication with an internal bore in the sting. The non-metric and metric portions of the balance are integrally connected together by a plurality of flexure beams such that the non-metric portion, the metric portion and the flexure beams form a one-piece construction which eliminates mechanical hysteresis between the non-metric and the metric portion. The system includes structures for preventing the effects of temperature, pressure and pressurized fluid from producing asymmetric loads on the flexure beams. A temperature sensor and a pressure sensor are located within the fluid-conducting passage of the balance. The system includes a longitudinal bellows member connected at two ends to one of the non-metric portion and the metric portion and at an intermediate portion thereof to the other of (1) and (2). A plurality of strain gages are mounted on the flexure beams to measure strain forces on the flexure beams. The flexure beams are disposed so as to enable symmetric forces on the flexure beams to cancel out so that only asymmetric forces are measured as deviations by the strain gages.

Horne, Warren L.↗
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.60 to 1.05 of a Model of the "Swallow" with Outer Wing Panels Swept 75 degree with and without Power Simulations

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model with the outer wing panels swept 75 deg. has been conducted in the Langley 16-foot transonic tunnel. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. The engine nacelles incorporated swept lateral and vertical fins for aerodynamic stability and control. Jet-off data were obtained with flow-through nacelles, simulating inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained at Mach numbers from 0.60 to 1.05 through a range of angles of attack and angles of side-slip. Control characteristics were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control. The results indicate that the basic wing-body configuration becomes neutrally stable or unstable at a lift coefficient of 0.15; addition of nacelles with fins delayed instability to a lift coefficient of 0.30. Addition of nacelles to the wing-body configuration increased minimum drag from 0.0058 to 0.0100 at a Mach number of 0.60 and from 0.0080 to 0.0190 at a Mach number of 1.05 with corresponding reductions in maximum lift-drag ratio of 12 percent and 33 percent, respectively. The nacelle-fin combinations were ineffective as longitudinal controls but were adequate as directional and lateral controls. The model with nacelles and fins was directionally and laterally stable; the stability generally increased with increasing lift. Jet interference effects on stability and control characteristics were small but the adverse effects on drag were greater than would be expected for isolated nacelles.

Schmeer, James W.↗
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.4 to 0.9 of a Model of the "Swallow" with Outer Wing Panels Swept 25 degree with and without Power Simulation

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model (the "Swallow") with the outer wing panels swept 25 deg has been conducted in the Langley 16-foot transonic tunnel. The wing was uncambered and untwisted and had RAE 102 airfoil sections with a thickness-to-chord ratio of 0.14 normal to the leading edge. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. A pair of swept lateral fins and a single vertical fin were mounted on each engine nacelle to provide aerodynamic stability and control. Jets-off data were obtained with flow-through nacelles, stimulating the effects of inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained through a Mach number range of 0.40 to 0.90 at angles of attack and angles of sideslip from 0 deg to 15 deg. Longitudinal, directional, and lateral control were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control.

Runckel, Jack F.↗
NASA NTRS1985

Fourier transform-infrared spectroscopic methods for microbial ecology: analysis of bacteria, bacteria-polymer mixtures and biofilms

Fourier transform-infrared (FT-IR) spectroscopy has been used to rapidly and nondestructively analyze bacteria, bacteria-polymer mixtures, digester samples and microbial biofilms. Diffuse reflectance FT-IR (DRIFT) analysis of freeze-dried, powdered samples offered a means of obtaining structural information. The bacteria examined were divided into two groups. The first group was characterized by a dominant amide I band and the second group of organisms displayed an additional strong carbonyl stretch at approximately 1740 cm-1. The differences illustrated by the subtraction spectra obtained for microbes of the two groups suggest that FT-IR spectroscopy can be utilized to recognize differences in microbial community structure. Calculation of specific band ratios has enabled the composition of bacteria and extracellular or intracellular storage product polymer mixtures to be determined for bacteria-gum arabic (amide I/carbohydrate C-O approximately 1150 cm-1) and bacteria-poly-beta-hydroxybutyrate (amide I/carbonyl approximately 1740 cm-1). The key band ratios correlate with the compositions of the material and provide useful information for the application of FT-IR spectroscopy to environmental biofilm samples and for distinguishing bacteria grown under differing nutrient conditions. DRIFT spectra have been obtained for biofilms produced by Vibrio natriegens on stainless steel disks. Between 48 and 144 h, an increase in bands at approximately 1440 and 1090 cm-1 was seen in FT-IR spectra of the V. natriegens biofilm. DRIFT spectra of mixed culture effluents of anaerobic digesters show differences induced by shifts in input feedstocks. The use of flow-through attenuated total reflectance has permitted in situ real-time changes in biofilm formation to be monitored and provides a powerful tool for understanding the interactions within adherent microbial consortia.

NASA Discipline Number 61-10↗