SEARCH · Engineering Papers

Results for “flow-through”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Study of Thermodynamic Vent and Screen Baffle Integration for Orbital Storage and Transfer of Liquid Hydrogen

A comprehensive analytical and experimental program was performed to determine the feasibility of integrating an internal thermodynamic vent system and a full wall-screen liner for the orbital storage and transfer of liquid hydrogen (LH2). Ten screens were selected from a comprehensive screen survey. The experimental study determined the screen bubble point, flow-through pressure loss, and pressure loss along rectangular channels lined with screen on one side, for the 10 screens using LH2 saturated at 34.5 N/cm2 (50 psia). The correlated experimental data were used in an analysis to determine the optimum system characteristics in terms of minimum weight for 6 tanks ranging from 141.6 m3 (5,000 ft3) to 1.416 m3 (50 ft3) for orbital storage times of 30 and 300 days.

Cady, E. C.↗

NASA NTRS1974

The 727/JT8D refan side nacelle airloads

Airloads on the 727/JT8D refan side engine nacelle are presented. These consist of surface static pressure distributions from two low speed wind tunnel tests. External nacelle surface pressures are from testing of a flow-through, body mounted nacelle model, and internal inlet surface pressures are from performance testing of a forced air inlet model. The method for obtaining critical airloads on nacelle components and a representative example are discussed.

Bailey, R. W.↗

NASA NTRS1974

Effects of wing/elevon gap sealing flapper doors on orbiter elevon effectiveness of model 16-0 in the NAAL 7.75 by 11 foot continuous flow wind tunnel (OA119A)

Space shuttle orbiter elevon effectiveness was measured with the 6 inch elevon/elevon and elevon/fuselage gaps and various configurations of wing/elevon upper hingeline gap sealing flapper doors. The elevon configuration parametric variations consisted of sealing the lower hingeline to prevent flow-through and testing a long chord flapper door, a short chord flapper door, no flapper door (elevon/wing gap upper hingeline completely open), and a completely sealed elevon at elevon deflections from +20 deg to -40 deg. Preliminary data analysis indicates loss of elevon effectiveness at deflections more negative than -20 deg, and little or no effect of flapper door configuration on elevon effectiveness. Flow visualization photographs taken at alpha = 15 deg for two flapper door configurations substantiated the force data results. Aerodynamic force and moment data were measured in the body axis by a 2.5 inch task type internal strain gage balance. The model was sting supported through the base region with a nominal angle of attack range of -10 deg less than or equal to alpha less than or equal to 24 deg at a model angle of sideslip of Beta equal to 0 deg.

Mennell, R.↗

NASA NTRS1974

Upper-surface blowing nacelle design study for a swept wing airplane at cruise conditions

A study was made to design two types of overwing nacelles for an existing wing-body at a design condition of Mach = 0.8 and C sub L = 0.2. Internal and external surface contours were developed for nacelles having either a D-shaped nozzle or a high-aspect-ratio nozzle for upper-surface blowing in the powered-lift mode of operation. The goal of the design was the development of external nacelle lines that would minimize high-speed aerodynamic interference effects. Each nacelle type was designed for both two- and four-engine airplanes using an iterative process of aerodynamic potential flow analysis. Incremental nacelle drag estimates were made for flow-through wind tunnel models of each configuration.

Gillette, W. B.↗

NASA NTRS1975

Comparison of wind tunnel test results at free stream Mach 0.7 with results from the Boeing TEA-230 subsonic flow method

The use of the Boeing TEA-230 Subsonic Flow Analysis method as a primary design tool in the development of cruise overwing nacelle configurations is presented. Surface pressure characteristics at 0.7 Mach number were determined by the TEA-230 method for a selected overwing flow-through nacelle configuration. Results of this analysis show excellent overall agreement with corresponding wind tunnel data. Effects of the presence of the nacelle on the wing pressure field were predicted accurately by the theoretical method. Evidence is provided that differences between theoretical and experimental pressure distributions in the present study would not result in significant discrepancies in the nacelle lines or nacelle drag estimates.

Mohn, L. W.↗

NASA NTRS1976

Investigation of upper-surface-blowing nacelle integration at cruise speeds utilizing powered engine simulators

Various overwing nacelle designs were investigated on a representative four-engine short-haul aircraft configuration during a combined analytical and experimental program. Design conditions were a Mach number of 0.7 and a lift coefficient of 0.4. All nacelles had D-shaped nozzle exits and included a streamline-contoured design, a low boattail angle reference configuration, and a high boattail angle powered lift design. Testing was done with the design four-engine airplane configuration as well as with only inboard nacelles installed. Turbopowered engine simulators were used to provide realistic representation of nacelle flows. Performance trends are compared for the various nacelle designs. In addition, comparisons are presented between analytical and experimental pressure distributions and between flow-through and powered simulator results.

Meleason, E. T.↗

NASA NTRS1977

Method for obtaining aerodynamic data on hypersonic configurations with scramjet exhaust flow simulation

A hypersonic wind tunnel test method for obtaining credible aerodynamic data on a complete hypersonic vehicle (generic X-24c) with scramjet exhaust flow simulation is described. The general problems of simulating the scramjet exhaust as well as accounting for scramjet inlet flow and vehicle forces are analyzed, and candidate test methods are described and compared. The method selected as most useful makes use of a thrust-minus-drag flow-through balance with a completely metric model. Inlet flow is diverted by a fairing. The incremental effect of the fairing is determined in the testing of two reference models. The net thrust of the scramjet module is an input to be determined in large-scale module tests with scramjet combustion. Force accounting is described, and examples of force component levels are predicted. Compatibility of the test method with candidate wind tunnel facilities is described, and a preliminary model mechanical arrangement drawing is presented. The balance design and performance requirements are described in a detailed specification. Calibration procedures, model instrumentation, and a test plan for the model are outlined.

Hartill, W. R.↗

NASA NTRS1977

Some experimental and theoretical flutter characteristics of an arrow-wing configuration

Experimental and theoretical flutter results are presented for a simplified 1/50-size wind-tunnel model of an arrow-wing configuration. Transonic flutter characteristics are presented for three configurations - wing without engine nacelles, wing with flow-through nacelles, and wing with pencil nacelles (thin, streamline bodies). Experimental results are correlated with analytical results obtained from kernel-function and doublet-lattice unsteady aerodynamic theories. Theoretical results are presented that show the effects on flutter of systematic changes in structural stiffness and mass.

Doggett, R. V., Jr.↗

NASA NTRS1977

Direct effects protection

Protection of an aircraft and each of its various systems against the direct effects of lightning were analyzed. Components located in different sections of the aircraft were individually examined since they are likely to experience different degrees of susceptibility to lightning, and may be vulnerable to different components of the lightning flash. The basic steps to be followed in establishing lightning protection were presented by discussing the varieties of arc entry and current flow-through damage. The lightning-strike zones and lightning current environments are established, since environmental conditions in the zones are those under which specific protective measures must perform. Airworthiness regulations which apply to lightning protection are cited.

Franklin A Fisher↗

NASA NTRS1977

Assessment of the impact of increased solar ultraviolet radiation upon marine ecosystems

Specifically, the study has addressed the following: (1) potential for irreversible damage to the productivity, structure and/or functioning of a model estuarine ecosystem by increased UV-B radiation or ecosystems highly stable or amenable to adaptive change, and (2) the sensitivity of key community components (the primary producers, consumers, and decomposers) to increased UV-B radiation. Three areas of study were examined during the past year: (1) a continuation of the study utilizing the two seminatural ecosystem chambers, (2) a pilot study utilizing three flow-through ecosystem tanks enclosed in a small, outdoor greenhouse, and (3) sensitivity studies of representative primary producers and consumers.

Vandyke, H.↗

NASA NTRS1978

Wind-tunnel investigation at Mach numbers from 1.90 to 2.86 of a canard-controlled missile with ram-air-jet spoiler roll control

The efficacy of using a ram-air-jet spoiler roll control device on a typical canard-controlled missile configuration was investigated. For roll control comparisons, conventional aileron controls on the tail fins were also tested. The results indicate that the roll control of the ram-air-jet spoiler tail fins at the highest free-stream Mach number compared favorably with that of the conventional 11-70 area-ratio tail fin ailerons, each deflected 10 deg. The roll control of the tail fin ailerons decreased while that of the ram-air-jet spoiler increased with free-stream Mach number. The addition of the ram-air-jet spoiler tail fins or flow-through tip chord nacelles on the tail fins resulted in only small changes in basic missile longitudinal stability. The axial force coefficient of the operating ram-air-jet spoiler is significantly larger than that of conventional ailerons and results primarily from the total pressure behind a normal shock in front of the nacelle inlets.

Blair, A. B., Jr.↗

NASA NTRS1978

Investigations of the influence of the profile thickness of the compressible plane flow through compressor cascades

Flow-through cascade of an aircraft turbine compressor is studied experimentally over wide range of Reynolds numbers and subsonic Mach numbers; it was found that deterioration of flow properties due to decreasing Reynolds numbers is less noticeable on thin profiles than on thick ones; however, thick profiles are advantageous in compressors designed for efficient partial load behavior because thick profiles have a relatively large range of usable inlet flow angles.

Bahr, J.↗

NASA NTRS1978

Polymeric electrolytic hygrometer

An improved flow-through electrolytic hygrometer is described which utilizes a long lasting oxidation-resistant, hollow fiber formed from persulfonic acid substituted polytetrafluoroethylene having closely spaced noble metal electrodes in contact with the inner and outer surfaces of the fiber. The fiber is disposed within a chamber so that the moisture-bearing gas passes in contact with at least one surface of the fiber. The electrodes are connected in series to a dc voltage supply and an ammeter. As the gas passes through the chamber, moisture absorbed into the wall of the fiber is electrolyzed to hydrogen and oxygen by the closely spaced electrodes. The amount of electricity required for electrolysis is proportional to the absorbed moisture and is observed on the ammeter.

Lawson, D. D.↗

NASA NTRS1977

Development of the propulsion simulator - A test tool applicable to V/STOL configurations

A turbine engine multi-mission propulsion simulator, capable of representing inlet/airframe/nozzle flowfield interactions for supersonic V/STOL aircraft wind tunnel models, is described. The propulsion simulator replaces conventional aero flow-through and jet effects models with a single model; flow field interactions modeled by the simulator may include close-coupled inlets and nozzles, non-axisymmetric vectoring exhaust nozzles, and forward canards mounted near the inlets and wings. Wind tunnel tests of the simulation system at Mach numbers up to 1.2 are reported for a model typical of a F-15 aircraft installation. The possibility of applying the simulator to advanced V/STOL design programs is also discussed.

Eigenmann, M. F.↗

NASA NTRS1978

Lightweight porous plastic plaque

The porosity and platability of various materials were investigated to determine a suitable substrate for nickel-plated electrodes. Immersion, ultrasonics, and flow-through plating techniques were tried using nonproprietary formulations, and proprietary phosphide and boride baths. Modifications to the selected material include variations in formulation and treatment, carbon loading to increase conductivity, and the incorporation of a grid. Problems to be solved relate to determining conductivities and porosities as a function of amount of nickel plated on the plastics; loading; charge and discharge curves of electrodes at different current densities; cell performance; and long-term degradation of electrodes.

Reid, M.↗

NASA NTRS1978

Laboratory studies of in vivo fluorescence of phytoplankton

A lidar system is developed that uses four selected excitation wavelengths to induce chlorophyll 'a' fluorescence which is indicative of both the concentration and diversity of phytoplankton. The operating principles of the system and the results of measurements of phytoplankton fluorescence in a controlled laboratory environment are presented. A comparative study of results from lidar fluorosensor laboratory tank tests using representative species of phytoplankton in single and multispecies cultures from each of four color groups reveals that (1) there is good correlation between the fluorescence of chlorophyll 'a' remotely simulated and detected by the lidar system and in-situ measurements using four similar excitation wavelengths in a flow-through fluorometer; (2) good correlation exists between the total chlorophyll 'a' calculated from lidar-fluorosensor data and measurements obtained by the Strickland-Parsons method; and (3) the lidar fluorosensor can provide an index of population diversity.

Brown, C. A., Jr.↗

NASA NTRS1979

Evaluation of turbo-propulsion simulators as a testing technique for fighter aircraft

Ames Research Center has under way a program to develop the technology for using turbine-powered jet engine simulators as a test technique for simulating installed jet engine characteristics in small-scale wind-tunnel models of complete VSTOL fighter configurations. The program consists of three key elements: (1) static testing SN003 prototype turbine engine simulator (MAPS), (2) the development of the Propulsion Simulator Calibration Laboratory at Ames, and (3) the design, fabrication, and testing of a twin-engine 'closely coupled' V/STOL fighter wind-tunnel model. The model will use the Compact Multi-mission Propulsion Simulator (CMAPS) and will also be tested in flow-through and jet-effects modes to assess the effect of simultaneous inlet and nozzle flow simulation. This paper includes a description of the planned effort and anticipated future tasks.

Bailey, R. O.↗

NASA NTRS1980

Design, fabrication and testing of a dual catalyst ammonia removal system for a urine VCD unit

A three-man capacity catalytic system for the recovery of water from urine was designed, constructed, and tested, it was designed to operate with feed streams containing high concentrations of urine vapor and only 5 to 7% of oxygen for the oxidation of ammonia and volatile organic vapor.It can operate either in a flow-through or a recycle mode and is capable of accepting the urine vapor produced by a vapor compression distillation evaporator. Testing consisted of short preliminary and optimization test, an endurance test of 74 hours continuous operation, and recycle tests using both air and oxygen. The system was designed for a urine processing rate of 0.86 liters/hr; however, it was tested at rates up to 1.2 liter/hr. Untreated urine evaporated by an electrically heated evaporator was used. The quality of the recovered water meets the U.S. Drinking Water Standards, with the exception of a low pH. Accumulation of solids in the urine sludge is reduced to approximately 65% of the anticipated value.

Budinikas, P.↗