SEARCH · Engineering Papers

Results for “external control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Infrared thermography NDT for in-situ defect detection in sandwich composite panel manufacturing

Composite manufacturing presents numerous challenges, as defects can arise from various sources throughout the process. In sandwich composite structures, the integration of a foam core introduces additional complexity and increases the likelihood of defect formation like delamination. To mitigate these issues and reduce the risk of future structural failures, in-situ monitoring during manufacturing is essential. This study investigates infrared (IR) thermography as a non-destructive technique for detecting manufacturing defects in foam-core sandwich composite panels under thermally excited conditions representative of in-situ processing. A stationary FLIR A8590 IR camera (640 × 512 pixels, 30Hz, 17mm lens, 9 ft stand-off distance) was used to monitor prefabricated panels subjected to controlled external heating simulating compression molding and resin cure exotherm. Interlaminar delamination defects with characteristic sizes ranging from 0.25 × 0.25in² to 5 × 5in² produced measurable surface temperature depressions of approximately 4–10°C during transient cooling, exceeding the effective noise floor of the camera by more than two standard deviations. Thicker laminates exhibited prolonged defect detectability windows due to increased thermal diffusion time. In contrast, embedded Teflon inclusions generated weak thermal contrasts of ≤ 3°C, approaching the measurement noise floor, due to limited thermal property contrast with the surrounding glass fiber composite. These results establish quantitative detectability limits for stationary thermographic inspection of sandwich composite panels under manufacturing-representative thermal cycles.

Barakat, Abdallah [ORNL] (ORCID:0000000296141398)↗

DOE OSTI2020

Exchange bias and quantum anomalous nomalous Hall effect in the MnBi 2 Te 4 /CrI 3 heterostructure

The layered antiferromagnetic MnBi 2 Te 4 films have been proposed to be an intrinsic quantum anomalous Hall (QAH) insulator with a large gap. It is crucial to open a magnetic gap of surface states. However, recent experiments have observed gapless surface states, indicating the absence of out-of-plane surface magnetism, and thus, the quantized Hall resistance can only be achieved at the magnetic field above 6 T. We propose to induce out-of-plane surface magnetism of MnBi 2 Te 4 films via the magnetic proximity with magnetic insulator CrI 3 . A strong exchange bias of ~40 meV originates from the long Cr- e g orbital tails that hybridize strongly with Te p orbitals. By stabilizing surface magnetism, the QAH effect can be realized in the MnBi 2 Te 4 /CrI 3 heterostructure. Moreover, the high–Chern number QAH state can be achieved by controlling external electric gates. Thus, the MnBi 2 Te 4 /CrI 3 heterostructure provides a promising platform to realize the electrically tunable zero-field QAH effect.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Toward three-dimensional DNA industrial nanorobots

Nanoscale industrial robots have potential as manufacturing platforms and are capable of automatically performing repetitive tasks to handle and produce nanomaterials with consistent precision and accuracy. We demonstrate a DNA industrial nanorobot that fabricates a three-dimensional (3D), optically active chiral structure from optically inactive parts. By making use of externally controlled temperature and ultraviolet (UV) light, our programmable robot, ~100 nanometers in size, grabs different parts, positions and aligns them so that they can be welded, releases the construct, and returns to its original configuration ready for its next operation. Our robot can also self-replicate its 3D structure and functions, surpassing single-step templating (restricted to two dimensions) by using folding to access the third dimension and more degrees of freedom. Our introduction of multiple-axis precise folding and positioning as a tool/technology for nanomanufacturing will open the door to more complex and useful nano- and microdevices.

Robotics↗

DOE OSTI2023

Electrolytic Etching of Germanium Substrates with Hydrogen Peroxide

Anodic electrolytic etching of germanium has been performed in hydrogen peroxide etchants with controlled external conditions. In-situ current and ex-situ etch-depths were measured and tracked with respect to etchant composition and stir rates. Gas bubbles formed during the etching process were found to cause non-uniformity in etch-current and surface quality. The effects were minimized in specific composition spaces. Quantitative analysis revealed a linear correlation of the number of electrons transferred during germanium oxidation with the number of surface atoms removed. Experimental results of 2.77 electrons/atom deviate significantly from 4 electrons/atom previously reported for silicon. The conclusion is that etching mechanisms for germanium are sufficiently different from those for silicon which invalidates the direct transfer of processing techniques between the two materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Ab Initio Quantum Information Processor Design with Single-Molecule Magnets: A Multiscale Modeling Approach (Final Report)

This final report summarizes the team's efforts to develop a multiscale modeling approach that ranges from different levels of ab-initio quantum chemistry simulations to effective models and time-dependent external control, and to use this approach to systematically design quantum information processors with TbPc 2 single-molecule magnets. The impact of the work is two-fold: (i) New quantum chemistry simulation techniques capable of treating complex, multiscale problems such as the TbPc 2 molecule were developed, and (ii) the prospects for building quantum processors based on single-molecule magnets coupled by superconducting transmission line resonators were analyzed. The outcomes of this project revealed that current technology is at the cusp of being able to realize the main components of such a processor, and they highlighted the need to achieve stronger molecule-resonator interactions to enhance the viability of this approach. The multiscale modeling techniques developed during this project are general and transferable to other molecules and will thus have a broad impact on the field of quantum chemistry. Methods for controlling and simulating many coupled qubits developed here will also impact other quantum information technologies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Mechanisms of Waterflood Inefficiency: Analysis of Geological, Petrophysical and Reservoir History, a Field Case Study of FWU (East Section)

The petroleum reservoir represents a complex heterogeneous system that requires thorough characterization prior to the implementation of any incremental recovery technique. One of the most commonly utilized and successful secondary recovery techniques is waterflooding. However, a lack of sufficient investigation into the inherent behavior and characteristics of the reservoir formation in situ can result in failure or suboptimal performance of waterflood operations. Therefore, a comprehensive understanding of the geological history, static and dynamic reservoir characteristics, and petrophysical data is essential for analyzing the mechanisms and causes of waterflood inefficiency and failure. In this study, waterflood inefficiency was observed in the Morrow B reservoir located in the Farnsworth Unit, situated in the northwestern shelf of the Anadarko Basin, Texas. To assess the potential mechanisms behind the inefficiency of waterflooding in the east half, geological, petrophysical, and reservoir engineering data, along with historical information, were integrated, reviewed, and analyzed. The integration and analysis of these datasets revealed that several factors contributed to the waterflood inefficiency. Firstly, the presence of abundant dispersed authigenic clays within the reservoir, worsened by low reservoir quality and high heterogeneity, led to unfavorable conditions for waterflood operations. The use of freshwater for flooding exacerbated the adverse effects of sensitive and migratory clays, further hampering the effectiveness of the waterflood. In addition to these factors, several reservoir engineering issues played a significant role in the inefficiency of waterflooding. These issues included inadequate perforation strategies due to the absence of detailed hydraulic flow units (HFUs) and rock typing, random placement of injectors, and uncontrolled injected fresh water. These external controlling parameters further contributed to the overall inefficiencies observed during waterflood operations in the east half of the reservoir. A detailed understanding of the mechanistic factors of inefficient waterflood operation will provide adequate insights into the development of the improved recovery technique for the field.

Morgan, Anthony (ORCID:0000000211519153)↗

DOE OSTI2020

Applying Dynamic Strain on Thin Oxide Films Immobilized on a Pseudoelastic Nickel-Titanium Alloy

Direct alteration of materials structure/function through strain is a burgeoning area of research that has allowed for novel properties of materials to emerge. Tuning materials structure can be achieved by controlling an external force imposed on materials and inducing stress-strain responses (i.e., applying dynamic strain). Electroactive thin films are typically deposited on shape or volume tunable elastic substrates, where mechanical loading (i.e. compression or tension) can affect films structure and function through imposed strain. Here we summarize methods for straining n-type doped titanium dioxide (TiO2) films prepared by a thermal treatment of a pseudo-elastic nickel-titanium alloy. The main purpose of the described methods is to study how strain affects electrocatalytic activities of metal oxide, specifically hydrogen evolution and oxygen evolution reactions. The same system can be adapted to study the effect of strain more broadly. Strain engineering can be applied for optimization of a material function, as well as for design of adjustable, multifunctional (photo)electrocatalytic materials under external stress control.

92 SC - Basic Energy Sciences (BES) (SC-22)↗

DOE OSTI2022

The role of toroidal rotation in the very high energy confinement quality observed in super H-mode experiments on DIII-D

In this paper, we report the key role that toroidal rotation and the related ExB shear physics played in the very high energy confinement quality (H98y2>1.5) of super H-mode experiments on DIII-D. Experiments show that the energy confinement quality decreases when toroidal rotation decreases due to the decreased externally controlled torque per particle. Meanwhile, the total pedestal pressure in the experiments remains very high during the rotation and confinement quality change. TGYRO transport modeling suggests the contribution from rotation in the ExB shear is responsible for the confinement quality in excess of standard H-mode (H98y2~1). CGYRO gyrokinetic simulations reveal the governing physics in the core plasma of super H-modes: significant up-shift of nonlinear the ITG critical gradient is observed when applying ExB shear physics in the modeling based on experimental data. The effects of other physical parameters and contribution from pedestal height, which may play minor roles in this study, are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

ENERGY STAR Residential Water Heater Specification and Test Method for Connected Residential Water Heaters

Electric water heaters have long been used as a tool for demand response due to their inherent thermal storage and large electric load. Traditionally, electric water heaters have been controlled by external load control switches, but that type of control does not work well with more efficient heat pump water heaters and cannot ensure that consumers have adequate hot water. Water heater manufacturers are adding more sophisticated controls that allow utilities or consumers to control their water heaters in new ways that can provide demand response without impacting consumer comfort. Further, the electric utility grid has seen a rapid increase the availability of renewable energy, which, depending on the type of renewable energy, can provide large amounts of energy for a portion of the day, but reduced or no energy at other times. In response to these advances in controls, availability of periodic renewable energy, and in an effort to have a standard which can be applied at a national level, ENERGY STAR and the Department of Energy have developed a Product Specification and Test Method for Connected Residential Water Heaters. In this session, we will discuss the new specification and test method, as well as show some initial results from running the new test method with two different HPWHs at NREL.

connected water heater↗

DOE OSTI2020

The effect of moisture on hydrocarbon-based solvent liquefaction of pine, cellulose and lignin

In this report we examined the effect of moisture on the solvent liquefaction of loblolly pine, cellulose, and lignin in tetralin at 280 °C and pressures ranging from 15 to 70 bar. Solvent liquefaction experiments were conducted in a quasi-batch reactor capable of continuous pressure control and external vapor condensation. Moisture was varied by the controlled addition of de-ionized water. Control over the system pressure subsequently impacted the removal of water vapor from the reactor. Liquid yield decreased by 25, 21, and 35 wt%, for pine, cellulose, and lignin, respectively, when moisture content was increased from 1 to 50 wt% at 42 bar. Humins were observed in the solid residue from liquefaction of wet cellulose. Wet lignin yielded a substantial amount of solid residue compared to dry lignin with a corresponding decrease in total phenolic monomer production. It was concluded that the ionic dissociation of water was an important factor in loss of liquid yield in the presence of water. Although water was less than 20 wt% of the solvent loading in these experiments, it strongly influenced the liquefaction of biomass and biomass components.

09 BIOMASS FUELS↗

DOE OSTI2024

External Fast Electrically-Controlled Ferroelectric Tuners for SRF Cavities

Euclid Techlabs LLC, in collaboration with JLAB (R. Rimmer, C. Hovater) has been awarded the Phase I 2021 DOE SBIR DE-SC0021510 project to develop the first Fast Ferroelectric reactive tuner (FRT) for a SRF accelerator that is currently in operation – CEBAF at JLAB, and is studying the possibility of developing a tuner designs for various new applications: fast frequency switching, transient detuning, and microphonics compensation for the SRF accelerators.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

External Fast Electrically-Controlled Ferroelectric Tuners for SRF Cavities

Explore the source record for details and available documents.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Predicting Safety Rod Reactivity Insertion in the Advanced Test Reactor

42 ENGINEERING↗

DOE OSTI2023

Local Power Impact Experiment Design for a New Fuel Type for use in the Advanced Test Reactor

The Advanced Test Reactor (ATR), and complimentary zero-power ATR Critical (ATRC) reactor, located at Idaho National Labs (INL), are undergoing conversion from Highly Enriched Uranium (HEU) to Low Enriched Uranium (LEU). Both have a variety of testing locations that can receive large variations in flux due to its unique serpentine design, consisting of five lobes (see Figure 1). Initial criticality and power distribution throughout the core are controlled by core-external outer shim control cylinders (OSCCs). Distinct test loops allow for testing at specific temperatures, pressures, and irradiation conditions. The ATR is one of the key nuclear engineering research and testing facilities within the DOE National Laboratory Complex, and the ATRC supports its operation [1]. Currently, the Office of Material Management and Minimization (M3) within the National Nuclear Security Administration of the DOE is working to convert the remaining research reactors, including the ATR, from 93% HEU fuel to 19.75% LEU fuel (LEU) to support non-proliferation [2]. Extensive materials testing at INL and internationally has demonstrated that a high-density uranium molybdenum (U 10Mo) alloy can meet the performance requirements of the remaining high powered research reactors. However, there are many technical challenges to address before the conversion to LEU can be successful, including the accurate characterization of the reactor core physics with LEU fuel. Reactor physics safety evaluations currently use Monte Carlo for the 21st Century (MC21), a continuous-energy Monte Carlo radiation transport code [3]. Existing MC21 models of the ATR and ATRC cores have a validation basis for use in neutronics analyses with HEU fuel. The models are used to support safety analyses that include comparisons to the safety requirements for the reactors. However, the use of the LOWE element in the ATR and ATRC is not currently covered by the current model validation basis. To deploy the new fuel type, extensive computational reactor physics support is necessary to support the use of LOWE in the ATR and ATRC. Therefore, LOWE requires a rigorous validation basis, aligned with that of HEU fuel, that takes advantage of the existing software tools and processes currently used for the ATR and ATRC. The experiment to validate of the MC21 models for determining power, the Power Impact Validation Experiment, will consist of two flux runs in the ATRC, one with fully HEU loading and one with a single LOWE element. Both flux runs will be instrumented with 20 sets of azimuthal fission wires and 3 sets of axial fission wires, as shown in Figure 4. Standard flux run methodology will be used [4]. Power Impact Validation Experiment data will be compared against MC21 calculated data, both for absolute fission rate accuracy and to determine the relative change in fission rates between the two runs. The results of the Power Impact Validation Experiment and subsequent evaluations will provide the validation basis for MC21 for use with LOWE elements. Key features of the Power Impact Validation Experiment include: (1) Two flux runs to allow for LOWE perturbed measurements to be compared to already validated measurements taken from a full core of HEU fuel, (2) Optimization of instrumentation to balance analytical needs with practical considerations (e.g., limited time window to count beta particles from fission products), and (3) Standard ATRC core loading, including both driver positions and flux traps, to minimize cost while remaining representative of typical ATR core loading.

42 ENGINEERING↗

DOE OSTI2026

Machine Tool Data Analytics for Digital Twin and Machine Predictive Maintenance

The primary objective of this project is to improve machining process performance using in-process machining data from the machine tool controller and external sensors. Advances in the Industrial Internet of Things (IIoT) enable monitoring of machines using controller data. Examples of the data provided by a controller include execution status of the controller, part count, block of code being executed, door status, tool position, the spindle and axis load, etc. MTConnect and OPC-UA are the two common protocols for capturing machine information. In this collaboration, methods for retrieving the machine controller data from selected machine tool controls and making these data accessible in different subsystems (such as digital twins and machine maintenance portals, etc.) will be developed and tested. In addition, analytics to improve machining process performance (by increasing productivity and reducing downtime) will be developed.

42 ENGINEERING↗

DOE OSTI2023

Simultaneous stabilization and control of the n = 1 and n = 2 resistive wall mode

Abstract DIII-D experiments demonstrate simultaneous stability measurements and control of resistive wall modes (RWMs) with toroidal mode numbers n = 1 and n = 2. RWMs with n > 1 are sometimes observed on DIII-D following the successful feedback stabilization of the n = 1 mode, motivating the development of multi- n control. A new model-based multi-mode feedback algorithm based on the VALEN physics code has been implemented on the DIII-D tokamak using a real-time GPU installed directly into the DIII-D plasma control system. In addition to stabilizing RWMs, the feedback seeks to control the stable plasma error field response, enabling compensation of the typically unaddressed DIII-D n = 2 error field component. Experiments recently demonstrated this algorithm’s ability to simultaneously control n = 1 and n = 2 perturbed fields for the first time in a tokamak, using reactor relevant external coils. Control was maintained for hundreds of wall-times above the n = 1 no-wall pressure limit and approaching the n = 1 and n = 2 ideal-wall limits. Furthermore, a rotating non-zero target was set for the feedback, allowing stability to be assessed by monitoring the rotating plasma response (PR) while maintaining control. This novel technique can be viewed as a closed-loop extension of active MHD spectroscopy, which has been used to validate stability models through comparisons of the PR to applied, open-loop perturbations. The closed-loop response measurements are consistent with open-loop MHD spectroscopy data over a wide range of β N approaching the n = 1 ideal-wall limit. These PR measurements were then fit to produce both VALEN and single-mode stability models. These models allowed for important plasma stability information to be determined and have been shown to agree with experimentally observed RWM growth rates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Autonomous hydrogel locomotion regulated by light and electric fields

Autonomous robotic functions in materials beyond simple stimulus-response actuation require the development of functional soft matter that can complete well-organized tasks without step-by-step control. We report the design of photo- and electroactivated hydrogels that can capture and deliver cargo, avoid obstacles, and return without external, stepwise control. By incorporating two spiropyran monomers with different chemical substituents in the hydrogel, we created chemically random networks that enabled photoregulated charge reversal and autonomous behaviors under a constant electric field. In addition, using perturbations in the electric field induced by a dielectric inhomogeneity, the hydrogel could be attracted to high dielectric constant materials and autonomously bypasses the low dielectric constant materials under the guidance of the electric field vector. The photo- and electroactive hydrogels investigated here can autonomously perform tasks using constant external stimuli, an encouraging observation for the potential development of molecularly designed intelligent robotic materials.

42 ENGINEERING↗

DOE OSTI2025

Simulating quantum-classical interfaces via the Lindblad master equation

In hybrid quantum systems, the interface between quantum and classical domains is essential for the generation, control, and measurement of quantum states. Quantum-classical interfaces (QCIs) are ubiquitous in devices such as optical modulators, quantum sensors, and signal processors, where classical signals influence quantum dynamics. In this paper, we employ the Lindblad master equation to simulate the evolution of a quantum system interacting with a classical control system. Our model captures both linear and nonlinear interactions by incorporating first- and second-order susceptibilities, and it quantifies the influence of externally applied control parameters on decoherence and state evolution. As an illustrative example, we analyze an optical modulator and demonstrate how variations in material response and drive conditions affect photon statistics, coherence, and phase-space distributions. In conclusion, the findings offer a path to an all-encompassing model for understanding and optimizing QCIs, with wide-ranging implications for the performance, design, and robustness of next-generation quantum devices.

Quantum engineering↗