Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “endurance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Thruster endurance test

A test system was built and several short term tests were completed. The test system included, in addition to the 30-cm ion thruster, a console for powering the thruster and monitoring performance, a vacuum facility for simulating a space environment, and a storage and feed system for the thruster propellant. This system was used to perform three short term tests (one 100-hour and two 500-hour tests), an 1108-hour endurance test which was aborted by a vacuum facility failure, and finally the 10,000-hour endurance test. In addition to the two 400 series thrusters which were used in the short term and 1100-hour tests, four more 400 series thrusters were fabricated, checked out, and delivered to NASA. Three consoles similar to the one used in the test program were also fabricated and delivered.

Collett, C.↗
NASA NTRS1978

Endurance testing of first generation /Block I/ commercial solar cell modules

NASA-LeRC has conducted outdoor endurance tests on modules commercially produced as part of the 46-kW purchase of first generation (Block I) modules by the JPL Low Cost Silicon Solar Array Project. Block I modules from four manufacturers were installed at commercial testing sites in Florida, Puerto Rico, and Arizona and at noncommercial sites in Cleveland, Ohio. The conditions endured by these modules included hot and dry, hot and humid, tropical rain forest, sea-air, urban industrial and urban clean; exposures were for periods up to one year. Test results are presented and discussed.

Anagnostou, E.↗
NASA NTRS1980

Tolerance of Lower Body Negative Pressure (LBNP) in endurance runners, weightlifters, swimmers and nonathletes

Thirteen endurance runners (R), 12 weightlifters (WL), 12 swimmers (SW) and 10 nonathletes (NA) were tested for their tolerance of lower body negative pressure (LBNP) in consecutive 5 minute stages at -20, -30, -40, -50 and -60 torr. Each subject also performed an exercise test on a bicycle ergometer with progressive workloads to exhaustion to determined aerobic capacity. The R had a much higher aerobic capacity than any of the other groups, but a significantly lower LBNP tolerance. While responses in heart rate and pulse pressure were quite similar in all 4 groups, the rate of increase in leg volume relative to LBNP stress (leg compliance, LC) was considerably greater in R than in the other athletes and NA. The greater LC in R could be attributed not only to a more rapid shift of blood to the lower extremities but also to a greater tendency for edema formation, both contributing to a more rapid loss in effective central blood volume for a given LBNP stress. These results substantiate earlier observations which led to the conclusion that endurance running is not advisable as a training regimen for astronauts.

Source record↗
NASA NTRS1981

Effects of curative treatment emphasizing endurance training on the performance and blood pressure of hypertensive and normotensives

The problem of normal values of blood pressure after exercise taking into account the blood pressure at the end of the exercise test is discussed. Hypertensives showed a lower working capacity than normotensives. In normotensives, however, systolic blood pressure at the end of an exercise correlated well with the working capacity. After the endurance cure submaximal blood pressure was markedly lower in hypertensives with a striking dependence on the level of initial values. Systolic blood pressure at the end of an exercise test was not changed significantly. Most probably it is not possible to overcome this malregulation in hypertensives by endurance training alone.

Worms, F.↗
NASA NTRS1982

Solar-powered airplane design for long-endurance, high-altitude flight

This paper describes the performance analysis and design of a solar-powered airplane for long-endurance, unmanned, high-altitude cruise flight utilizing electric propulsion and solar energy collection/storage devices. For a fixed calendar date and geocentric latitude, the daily energy balance, airplane sizing, and airplane aerodynamics relations combine to determine airplane size and geometry to meet mission requirements. Vehicle component weight loadings, aerodynamic parameters, and current and projected values of power train component characteristics form the basis of the solution. For a specified mission, a candidate airplane design is presented to demonstrate the feasibility of solar-powered long endurance flight. Parametric data are presented to illustrate the airplane's mission flexibility.

Youngblood, J. W.↗
NASA NTRS1983

Endurance test of a 30-CM-diameter engineering model ion thruster. Task 12: Investigation of thin-film erosion monitors for ion thrusters

An investigation of short term measurement techniques for predicting the wearout of ion thrusters resulting from sputter erosion damage is described. The previously established laminar thin film techniques to provide high precision erosion rate data. However, the erosion rates obtained using this technique are generally substantially higher than those obtained during long term endurance tests (by virtue of the as deposited nature of the thin films), so that the results must be interpreted in a relative sense. Absolute measurements can be performed using a new masked substrate arrangement which was developed during this study. This new technique provides a means for estimating the lifetimes of critical discharge chamber components based on direct measurements of sputter erosion depths obtained during short duration (10 hour) tests. The method enables the effects on lifetime of thruster design and operating parameters to be inferred without the investment of the time and capital required to conduct long term (1000 hour) endurance tests. Results obtained using the direct measurement technique are shown to agree with sputter erosion depths calculated for the plasma conditions of the test and also with lifetest results. The direct measurement approach is shown to be applicable to both mercury and argon discharge plasma environments and should be useful in estimating the lifetimes of inert gas and extended performance mercury ion thrusters presently under development.

Beattie, J. R.↗
NASA NTRS1983

Free-piston stirling engine endurance test program

The Free-Piston Stirling Engine (FPSE) has the potential to be a long-lived, highly reliable, power conversion device attractive for many product applications such as space, residential, or remote-site power. The purpose of endurance testing the FPSE is to demonstrate its potential for long life. The endurance program was directed at obtaining 1000 operational hours under various test conditions: low power, full stroke, duty cycle, and stop/start. Critical performance parameters were measured to note any change and/or trend. Inspections were conducted to measure and compare critical seal/bearing clearance. The engine performed well throughout the program, completing the 1000 hours. Hardware inspection, including the critical clearances, showed no significant change in hardware or clearance dimensions. The performance parameters did not exhibit any increasing or decreasing trends. The test program confirms the potential for long-life FPSE applications. Additional testing is planned to increase the test hours to 10,000.

Dochat, G.↗
NASA NTRS1985

Free-piston Stirling engine/linear alternator 1000-hour endurance test

The Free Piston Stirling Engine (FPSE) has the potential to be a long lived, highly reliable, power conversion device attractive for many product applications such as space, residential or remote site power. The purpose of endurance testing the FPSE was to demonstrate its potential for long life. The endurance program was directed at obtaining 1000 operational hours under various test conditions: low power, full stroke, duty cycle and stop/start. Critical performance parameters were measured to note any change and/or trend. Inspections were conducted to measure and compare critical seal/bearing clearances. The engine performed well throughout the program, completing more than 1100 hours. Hardware inspection, including the critical clearances, showed no significant change in hardware or clearance dimensions. The performance parameters did not exhibit any increasing or decreasing trends. The test program confirms the potential for long life FPSE applications.

Rauch, J.↗
NASA NTRS1984

IAPS (8-cm) ion thruster cyclic endurance test

Attention is given to the cyclic endurance qualification test, performed in a vacuum facility with a liquid nitrogen-cooled cryosurface and a frozen mercury target, to which a mercury-ion thruster representative of Ion Auxiliary Propulsion System (IAPS) thrusters was subjected. At the time that the endurance test was successfully concluded, upon consumption of the IAPS propellant tank's mercury, 8,471 hours of 'beam-on time' and 599 cycles had been accumulated. The system's Power Electronics Unit accumulated 10,268 hours of test time with high voltage applied to the operating thruster or dummy load.

Dulgeroff, C. R.↗
NASA NTRS1987

An airfoil designed for a high-altitude, long endurance remotely piloted vehicle

The preliminary design of high-altitude, long-endurance RPVs is complicated by the paucity of data concerning airfoils with high lift coefficients at low Re numbers. Attention is presently given to a generic airfoil of this type for the design Re number range of 700,000 to 2 million. Low drag is predicted for lift coefficients from 0.4 (for high speed dashes) to 1.5 (for maximum mission endurance). The airfoil is such that its maximum lift coefficient, at 1.8, is unaffected by the surface contamination that would be encountered during takeoffs and landings in rain or over insect-infested runways.

Maughmer, Mark D.↗
NASA NTRS1990

Performance and endurance tests of a laboratory model multipropellant resistojet

This paper presents the results of an effort to demonstrate the technological readiness of a long-life multipropellant resistojet for Space Station auxiliary propulsion. A laboratory model resistojet made from grain-stabilized platinum served as a test bed to evaluate the design characteristics, fabrication methods, and operating strategies for an engineering model multipropellant resistojet developed as part of the NASA Space Station propulsion system Advanced Development Program. The laboratory model thruster was characterized for performance on a variety of fluids expected to be available onboard a Space Station, then subjected to a 2000-h, 2400-thermal-cycle endurance test using carbon dioxide propellant. Maximum thruster temperatures were approximately 1400 C. Significant observations from the laboratory model thruster performance and endurance tests are discussed as they relate to the design of the engineering model thruster.

Morren, W. Earl↗
NASA NTRS1990

The design and flight testing of a long endurance RPV

This paper covers the design process for a long endurance RPV. The 56-pound RPV must operate in the 25-60 knot speed range at low altitudes. An airfoil designed for low-Reynolds-number applications was used with a wing of aspect ratio 22 to reach an estimated L/D(max) of 25. Wing tip feathers were designed to reduce the induced drag. A comparison between the computed aerodynamic predictions and wind-tunnel results is given. The estimated endurance is on the order of 50 hours/gallon of fuel. A three-surface configuration was chosen, and the predicted handling quality and performance results obtained so far are given. The structural challenges in building a lightweight structure for the wing and control surfaces are outlined. The flight test program is currently underway.

Siddiqi, Shahid↗
NASA NTRS1992

Ion engine endurance testing at high background pressures

Ion engine endurance testing at vacuum chamber pressures in the low 10 exp -3 Pa range is enabled through the use of a three-grid accelerator system with the decelerator grid biased 50 to 100 volts negative of neutralizer cathode potential. The negative decelerator grid serves to collect the facility induced charge exchange ion current which normally results in rapid erosion of the accelerator grid during testing at elevated vacuum chamber pressures. This screen, accelerator, negative decelerator (SAND) grid configuration enables an order of magnitude reduction in vacuum chamber pumping speeds relative to that required for endurance testing of ion engines with conventional two-grid accelerator systems. A 900-hr test of a 30-cm diameter engine at 6.5 kW and a tank pressure of 3.7 x 10 exp -3 Pa was performed to test the feasibility of the three-grid SAND accelerator system technology. Grid erosion rates from this test are compared to those from a 200-hr test performed with the same discharge chamber, in the same test facility, and at the same background pressure with a conventional two grid accelerator system. The SAND optics resulted in greater than a factor of 100 reduction in accelerator grid erosion rate relative to the two-grid system.

Brophy, John R.↗
NASA NTRS1993

Wind-shear endurance capability for powered-lift aircraft

The present treatment of safety margin considerations for powered-lift (upper wing surface blowing) STOL aircraft emphasizes wind shear endurance, in order to establish safety margin criteria for such aircraft that are equivalent to those of conventional transport aircraft. The simulation results obtained show that a 6.6 deg climb gradient at V(app) for STOL aircraft is required for equivalent shear endurance in approaching a long STOL airport runway, if the STOL aircraft is equipped with an elaborate control/display system and is permitted a change in configuration.

Bando, Toshio↗
NASA NTRS1927

Three methods of calculating range and endurance of airplanes

This report develops new equations which give the range and endurance of airplanes with an accuracy equal to that obtained from a step-by-step integration of the flight. A method of obtaining equally satisfactory results from Brequet's equations is also given in detail. A third method of calculating range and endurance, derived by the writer for use in routine estimating in the Bureau of Aeronautics, is also given in full. The reports contains tables and curves arranged for convenient use and illustrates the three methods by comparative estimates.

Diehl, Walter S↗
NASA NTRS1993

Force-endurance capabilities of extravehicular activity (EVA) gloves at different pressure levels

The human hand is a very useful multipurpose tool in all environments. However, performance capabilities are compromised considerably when gloves are donned. This is especially true to extravehicular activity (EVA) gloves. The primary intent was to answer the question of how long a person can perform tasks requiring certain levels of exertion. The objective was to develop grip force-endurance relations. Six subjects participated in a factorial experiment involving three hand conditions, three pressure differentials, and four levels of force exertion. The results indicate that, while the force that could be exerted depended on the glove, pressure differential, and the level of exertion, the endurance time at any exertion level depended just on the level of exertion expressed as a percentage of maximum exertion possible at that condition. The impact of these findings for practitioners as well as theoreticians is discussed.

Bishu, Ram R.↗
NASA NTRS1994

Effect of power system technology and mission requirements on high altitude long endurance aircraft

An analysis was performed to determine how various power system components and mission requirements affect the sizing of a solar powered long endurance aircraft. The aircraft power system consists of photovoltaic cells and a regenerative fuel cell. Various characteristics of these components, such as PV cell type, PV cell mass, PV cell efficiency, fuel cell efficiency, and fuel cell specific mass, were varied to determine what effect they had on the aircraft sizing for a given mission. Mission parameters, such as time of year, flight altitude, flight latitude, and payload mass and power, were also altered to determine how mission constraints affect the aircraft sizing. An aircraft analysis method which determines the aircraft configuration, aspect ratio, wing area, and total mass, for maximum endurance or minimum required power based on the stated power system and mission parameters is presented. The results indicate that, for the power system, the greatest benefit can be gained by increasing the fuel cell specific energy. Mission requirements also substantially affect the aircraft size. By limiting the time of year the aircraft is required to fly at high northern or southern latitudes, a significant reduction in aircraft size or increase in payload capacity can be achieved.

Colozza, Anthony J.↗
NASA NTRS2001

An FPGA-Based Test-Bed for Reliability and Endurance Characterization of Non-Volatile Memory

Memory technologies are divided into two categories. The first category, nonvolatile memories, are traditionally used in read-only or read-mostly applications because of limited write endurance and slow write speed. These memories are derivatives of read only memory (ROM) technology, which includes erasable programmable ROM (EPROM), electrically-erasable programmable ROM (EEPROM), Flash, and more recent ferroelectric non-volatile memory technology. Nonvolatile memories are able to retain data in the absence of power. The second category, volatile memories, are random access memory (RAM) devices including SRAM and DRAM. Writing to these memories is fast and write endurance is unlimited, so they are most often used to store data that change frequently, but they cannot store data in the absence of power. Nonvolatile memory technologies with better future potential are FRAM, Chalcogenide, GMRAM, Tunneling MRAM, and Silicon-Oxide-Nitride-Oxide-Silicon (SONOS) EEPROM.

Rao, Vikram↗