Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “delamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Understanding the high-temperature behavior and corrosion resistance of Cr-Nb coated cladding for BWRs

While Cr-coated Accident Tolerant Fuel has proven successful in Pressurized Water Reactors, its dissolution in high dissolved oxygen Boiling Water Reactor environments represents a major technological barrier. Here, this study presents a comprehensive evaluation of novel Cr-Nb alloys as a coating breakthrough solution for Accident Tolerant Fuel cladding in Boiling Water Reactors. We systematically investigated Physical Vapor Deposited Cr-Nb coatings with 13% and 24 at% Nb content on commercial Zr-based cladding through rigorous testing under both normal and accident conditions. Our results demonstrate Cr-Nb coatings remained completely intact during extended Boiling Water Reactor autoclave testing, while pure Cr coatings failed catastrophically due to oxide dissolution. Under Loss-of-Coolant Accident conditions at 1100°C, Cr-Nb coatings maintained protective capability for 45 min. At 800°C, the alloy coatings matched pure Cr's excellent corrosion resistance. Despite microstructural changes during prolonged high-temperature exposure, no coating delamination occurred, ensuring continued protection of the underlying Zr substrate. These findings establish Cr-Nb coatings as a viable Accident Tolerant Fuel solution for Boiling Water Reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Ionic Interdiffusion at Cathode|Solid-Electrolyte Interface: A Machine Learning–Assisted Multiscale Investigation and Mitigation Strategies

Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.

Ncube, Musawenkosi K.↗
DOE OSTI2026

A Novel Surface Restoration Method for Hydropower Steel Components: Plasma Gouging and Inconel Cold Spray Coating for Material Repair

A novel surface restoration approach combining plasma gouging with subsequent cold spray deposition is demonstrated in this study. Plasma gouging effectively removes the damaged steel surface, leaving grooves and forming a plasma gouging affected zone up to ~300?µm thick. Within this zone, a hardened martensitic layer with a peak hardness of ~370?HV—almost twice that of the base substrate (~200?HV)—is produced. Following plasma gouging, cold spray deposition is applied to rebuild the surface. Experimental results reveal that cold spray coatings deposited at low energy suffer from delamination, whereas high energy cold spray deposits yield a well-bonded coating. Microstructural analysis further shows that the martensitic layer formed by plasma gouging undergoes dynamic recrystallization during cold spray, reducing the hardness to 317?HV. These findings demonstrate the feasibility of this hybrid method for effective surface restoration of damaged steel components.

Wang, Tianhao↗
DOE OSTI2025

Characterization of the microstructure of yttrium hydride under proton irradiation

High moderation per unit volume solid moderator materials like yttrium hydride (YH x ) are necessary for compact nuclear microreactors. However, the phase stability and hydrogen transport processes of YH x under high-temperature irradiation are largely unknown. Proton irradiation was conducted on YH x at 300 °C and 580 °C to 0.2 dpa using 1 MeV or 2 MeV protons in a high-vacuum environment. The hydrogen concentration was determined before and after irradiation using elastic recoil detection analysis, and microstructural evolution was examined via post-irradiation scanning transmission electron microscopy and Raman spectroscopy. Dislocation loops and cavities were observed in all conditions; their distribution was correlated with the bombarding proton energy and ion irradiation temperature. This work revealed that hydrogen retention is proportional to the formation of traps for hydrogen gas atoms and identified pathways for hydrogen release. The relative contributions of bulk or fast diffusion paths, such as grain boundaries, delamination boundaries, and stacking faults are discussed; the primary mechanisms of hydrogen loss are likely based on diffusion, ruling out artefacts of the experimental design. In conclusion, the study suggests proton irradiation may be a strong surrogate to study hydrogen transport in hydride moderator materials under irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel

The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Tensile properties of co-rolled Zr/U-10Mo fuel at ambient and elevated temperatures

The United States High Performance Research Reactor (USHPRR) initiative is currently interested in replacing high-enriched uranium fuel in research reactors with high-assay low-enriched uranium fuel. Here, this work aimed to assist in that mission by providing tensile and bend test data on bare U-Mo and tensile test data on co-rolled Zr/U-10Mo plates at differing thicknesses (0.285 mm, 0.300 mm, and 0.465 mm) and temperatures (293 K, 473 K, and 623 K). Yield strength and ultimate tensile strength values are reported along with an in-depth comparison of how temperature, rolling direction, thickness, and the presence of the Zr-interlayer affect mechanical properties. Results showed that yield strength and ultimate tensile strength in Zr/U-10Mo foils lower as temperature increases by approximately 300 MPa from 293 to 473 K, and another 100 MPa from 473 to 623 K. Additionally it was found that with increased temperature, there is less differentiation in fuel necking and delamination behavior, as well as a greater perceived elongation to fracture. The elastic modulus of co-rolled mini-plates does not follow the volumetric rule of mixtures in terms of averaged strength and is actually lower than the reported moduli of both Zr and U-10Mo.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Performance characterization of 5×5×12 mm 3 virtual Frisch-grid TlBr detectors

Thallium bromide (TlBr) is a promising material for semiconductor gamma-ray detectors due to its high atomic number (Tl = 81, Br = 35), high density (7.56 g/cm 3 ), and relatively low melting point (460 °C). These properties give TlBr several competitive features, including high detection efficiency, good energy resolution, and lower fabrication costs, making it suitable for applications requiring compact, highly sensitive gamma-ray detection systems. Recent developments of TlBr detectors have progressed toward thicker crystals, up to 10–20 mm, configured as pixelated or virtual Frisch-grid (VFG) devices with volumes >1 cm 3 . Despite these advances, challenges remain in practical implementation, including material and fabrication issues that affect energy resolution, device stability, performance, and longevity. These challenges are similar to those faced by HgI 2 and lead-halide perovskite detectors. Here, this study presents results from characterizing over 100 position-sensitive 5×5×12 mm 3 virtual Frisch-grid detectors fabricated by Radiation Monitoring Devices Inc. For a prototype Radioisotope Identification Device (RIID). The work identified factors limiting the performance and longevity of TlBr detectors, including stochastic response variations that limit the energy resolution to 2–3 % (at 662 keV) for most devices, performance degradation associated with defect decoration, and contact delamination. Addressing these issues advances the use of TlBr and similar materials for reliable, high-resolution gamma-ray spectroscopy.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D

Characterization and testing of advanced plasma-facing materials (PFMs) for Fusion Pilot Plants (FPP) is being conducted at the DIII-D National Fusion Facility through the ongoing two-year FPP Candidate Materials Thrust. Year one tested 17 novel materials utilizing the Divertor Materials Evaluation System (DiMES), with samples analyzed pre- and post-experiment via SEM, EDS, and confocal microscopy. Repeatable reference discharges were developed to ensure uniformity between experiments, including a new strike-point rastering scenario to provide more uniform heat/particle flux across DiMES during ELMing H-mode discharges. Various sample geometries and temperatures were used to achieve FPP-relevant conditions, including samples angled 10° towards the incident plasma flux and pre-heating up to 500 °C. The first exposure of liquid lithium (Li) capillary porous structures in a tokamak demonstrated uniform emission of Li vapor and suppression of Li droplets in H-mode when preheated to 350 °C. Dispersoid-strengthened W with 1 wt% TaC, TiC, and ZrC exposed to H-mode showed cracking and dispersoid ejection for all varieties except TiC, providing a clear down-selection. Ultra-high temperature ceramic materials TiB 2 and ZrB 2 showed minimal degradation under L-mode exposure. Silicon carbide (SiC) fiber composites showed arcing along edges, while CVD SiC remained pristine. Atmospheric plasma-sprayed W and SiC coatings endured H-mode exposure without macroscopic delamination; SiC exhibited granular ejection, while W showed increased outgassing. Additional W-based alloys were stress tested in H-mode, including Ni-based W heavy alloys, W f SiC f /W composites, W multi-principle element alloys, and functionally-graded W/SiC, to varying degrees of success.

DIII-D↗
DOE OSTI2025

Exploring strain rate effects upon 3D materials using high speed in situ X-ray tomoscopy

Cellular materials are ubiquitous in our modern society. They may be stochastic gas-blown foams (e.g., polyurethane), foamed starches (e.g., cereals), or, in this case, 3D printed microlattices. Failure in these materials is often driven by surface or sub-surface defects, which may be nucleated at a surface roughness, an interior void, or inclusion interfaces that may not be typically observable. Obfuscating our understanding further, bulk materials are known to exhibit strain-rate-dependent mechanical response, making a subsurface understanding of damage even more critical. For the first time, an in situ uniaxial mechanical loading stage that simultaneously rotates specimens up to 18 Hz was fielded at a synchrotron for 3D tomographic imaging. This capability opens a plethora of materials science opportunities to explore strain rate effects in materials and examining deformation, fracture, and delamination’s (in composites) for a complete 3D picture (movie) of material response. We demonstrate the deformation of 3D printed polymer lattice structures, of three different material types, at 0.25, 1.1, and 2.2 s −1 strain rates. We successfully imaged the 3D deformation of these materials and can directly compare the same printed structure to the three material types at three strain rates, all in 3D. Material point method simulations were applied to one of the materials to better understand the role of voids on the 3D printed structure’s performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tribological behavior of spark plasma sintered Ti 3 SiC 2 MAX phase composites

Ti₃SiC₂ MAX phases are considered promising candidates for tribological applications; but, their low hardness (5-6 GPa) can lead to increased abrasive wear and higher wear rates. This study investigates the effect of incorporating hard SiC particles on microstructure, mechanical, and tribological behavior of Ti₃SiC₂-SiC-based MAX phase composites prepared using spark plasma sintering at 1400 °C, 40 MPa, 15-minute holding time. Phase and microstructural characterization of composites confirmed the formation of Ti₃SiC₂ MAX phase (90%) along with TiC as a minor phase (10%). For Ti₃SiC₂-SiC, homogeneous distribution of SiC grains within Ti₃SiC₂ matrix resulted in increased hardness from ~11.6 GPa to ~14.8 GPa; however, the flexural strength decreased from ~615 MPa to ~597 MPa due to coefficient of thermal expansion mismatch. Tribological behavior of Ti₃SiC₂-SiC MAX phase composites was assessed using unidirectional sliding ball-on-flat tests with a 52100 steel ball at different loads and a constant speed of 0.05 m/s. SiC reinforced composites exhibited a decreased friction coefficient from 0.39 to 0.29 and wear rates comparable to Ti₃SiC₂ (7-10×10⁻³ mm³/N·m). SEM and EDS analysis of the worn surfaces indicated material transfer from the steel ball counter body and its oxidation due to frictional heating, at lower loads (2N and 5N), whereas at higher load (10N), fracture of the transfer layer dominated, with the presence of microcracks, delamination, grain pull-outs, and wear debris. Improved mechanical properties and good adhesion of SiC with Ti₃SiC₂ matrix resulted in reduced microcracks and grain pull-outs, making Ti₃SiC₂-SiC/Steel tribo-pair more suitable for tribological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nanoscale Examination of Chemical and Enzymatic Degradation of Plant Cell Walls

Lignocellulosic materials present the largest source of biomass for biotechnology and green energy. This study aimed at better understanding the cell wall disintegration mechanisms relevant for the biochemical conversion of biomass to carbohydrates. Herein, we examined nanoscale changes in cell wall structure and composition upon industrially relevant chemical and enzymatic treatments to achieve the desired level of breakdown. One treatment involved hydrogen peroxide and acetic acid to remove lignin. Another modification used the cellulase enzyme for cell wall degradation. Band excitation contact resonance atomic force microscopy was used to visualize and mechanically characterize cell wall layers. After cellulase treatments, we detected microcracks across the cell wall. Wet-chemical, Fourier-transform infrared and Raman spectroscopic analyses confirmed the removal of lignin and extractives through acid bleaching, while the enzymatic treatment minimally affected the biopolymer composition. Delignification resulted in cell wall delamination and reduced stiffness. In conclusion, X-ray diffraction revealed changes in cellulose structure and crystallinity.

Soini, Steven A. [Florida Atlantic Univ., Boca Rat↗
DOE OSTI2026

Irradiation-Induced Structural Disorder and Its Influence on the Mechanical Response of Polycrystalline MoS2

Molybdenum disulfide (MoS2) thin films are widely used as dry-film lubricants and protective coatings in aerospace and other radiation-exposed environments. Conventional synthesis routes produce polycrystalline films whose grain boundaries and other native defects cause their mechanical and tribological behavior to differ substantially from that of ideal single crystals. Under irradiation, these films progressively evolve from polycrystalline structures, composed of layered MoS2 grains, into highly disordered and eventually amorphous structures, altering both their tribological performance and mechanical integrity. Here, we employ reactive atomistic simulations to investigate irradiation-driven structural evolution in bulk polycrystalline MoS2. Using controlled primary knock-on atom (PKA) events, we characterize the progressive transition from a polycrystalline microstructure to an amorphous network by tracking defect accumulation and structural disorder. We then establish how this transition modifies the dominant deformation mechanisms and the temperature-dependent tensile response. Specifically, irradiation suppresses interlayer sliding and delamination, mechanisms which facilitate the deformation of the pristine polycrystal, resulting in defect-induced hardening. Broadly, our results establish direct process–structure–property relationships linking irradiation-induced defect accumulation, microstructural evolution, deformation mechanisms, and mechanical behavior, providing an atomistic framework for understanding the structural integrity and long-term reliability of irradiated MoS2 coatings.

Moore, Daniel [Sandia National Laboratories (SNL)]↗
DOE OSTI2026

Influence of CO 2 -Regenerative Film Properties in Enhancing C 2+ Products Selectivity While Mitigating CO 2 Crossover

Zero-gap anion-exchange membrane electrode assembly (AEMEA) electrolyzers operating in alkaline media face challenges such as CO 2 crossover and salting-out. The bipolar membrane electrode assembly (BPMEA) electrolyzer, using DI water as the electrolyte, addresses both CO 2 crossover and salting-out issues. As cations, which are crucial in stabilizing the CO 2 R intermediates, are absent in the electrolyte, cations embedded in the AEM play an important role in dictating the CO 2 R selectivity and activity in BPMEA systems. So far, no systematic study has been conducted on the influence of cations embedded in AEMs on CO 2 selectivity and activity in BPMEA systems. Moreover, BPMEA systems impose an additional challenge: low stability due to delamination of the bipolar membrane caused by CO 2 regeneration at the membrane-membrane interface. To enhance the stability of the electrolyzer, a simple yet highly reproducible strategy for coating a porous CO 2 regenerative film on smooth Nafion 117 is demonstrated in this work, along with a systematic study of four different commercially available AEMs, composed of different cations and cation densities, for use in combination with Nafion 117 and copper catalyst at the cathode. We found that the PiperION membrane delivers selectivity and activity comparable to those of alkali-metal cations, owing to the enhanced local electric field resulting from the combined effects of a high positive charge on the N atom of the piperidinium cation and the high ion-exchange capacity. Further, we studied the influence of the thickness of the PiperION porous layer over Nafion 117 on CO 2 R selectivity and found that 70 μm is the minimum thickness to achieve maximum C 2+ products selectivity, reduced the CO 2 crossover to 5% from 25% at 4 SCCM and 150 mA cm –2 , and was stable for operation beyond 100 h. The selectivity of this system, compared with AEMEA, and stability outperformed both AEMEA and BPMEA. This study helps design more effective BPMs to inhibit CO 2 crossover while enabling stable and selective electrochemical CO 2 reduction to C 2+ hydrocarbons.

Cations↗
DOE OSTI2026

Thermochemistry of Layered and Two-Dimensional Niobium Carbo-Chalcogenides

Two-dimensional transition metal carbo-chalcogenides (TMCCs) represent a novel class of layered materials with tunable electronic structures and high chemical versatility, making them promising candidates for energy and environmental applications. In this work, the structural and thermochemical properties of a series of TMCCs are investigated. High-temperature oxidative solution calorimetry, conducted at 800 °C in molten sodium molybdate (3Na2O·4MoO3), was used to determine the enthalpies of oxidation and formation from the elements at 25 °C, enabling a comprehensive thermodynamic assessment. Comparison of these enthalpies reveals distinct stability trends across the series. Cu0.67Nb2S2C exhibits the most exothermic oxidation enthalpy, indicating a strong thermodynamic driving force for oxidation and reduced resistance to oxidative degradation. Its positive enthalpy of formation from the elements suggests lower thermodynamic stabilization relative to the other compositions, consistent with the energetic influence of Cu and residual Fe within the Nb–S–C framework. In contrast, delaminated Nb2S2C exhibits poor oxidative stability but a highly exothermic enthalpy of formation, consistent with a defect-rich, metastable structural state rather than enhanced lattice stability. These findings establish correlations between crystal structure and energetic stability, providing insights into the design of robust TMCC-based materials for advanced energy and environmental technologies.

Cassell, Nakeshma [Clemson University]↗
DOE OSTI2026

Irradiation Driven Restructuring of Nanocrystalline ThO 2 and Th 1–x U x O 2 Thin Films

Irradiation induced structural changes of actinide oxide materials is a key consideration in their development and use as nuclear fuels. This study reported on the synthesis of ThO 2 and Th 1–x U x O 2 (x = 0.15, 0.50) thin films, fabricated using electrospray-assisted solution combustion synthesis, and their responses to ion irradiation. Krypton ion irradiations, up to a fluence of 1 × 10 16 ions/cm 2 , were carried out to simulate radiation damage induced by fission products in a reactor environment. Structural and chemical changes induced by irradiation were analyzed using high-resolution scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), and electron energy-loss spectroscopy (EELS). It was determined that the extent and nature of irradiation-induced damage are strongly correlated with the uranium content. ThO 2 films were most susceptible to radiation-induced damage, with significant cavity formation and delamination from the substrate at high fluence. Of the compositions studied, Th 0.85 U 0.15 O 2 films showed the highest stability, characterized by moderate grain growth and the absence of voids or severe defect structures. In contrast, Th 0.5 U 0.5 O 2 films accumulated extensive damage, including the formation of a nanocrystalline central region. EELS analysis indicated that oxygen displacement is the primary driver of structural degradation in Th 0.5 U 0.5 O 2 films. α-particle spectroscopy confirmed minimal actinide loss across all compositions, underscoring the mechanical robustness of the films. These findings provide insight into the irradiation-induced damage mechanisms in Th O2 and Th 1–x U x O 2 systems, supporting their development as potential materials for nuclear fuels and irradiation-tolerant thin film targets in nuclear physics measurements.

Th1−xUxO2↗
DOE OSTI2024

Topological Considerations in Electrolyte Additives for Passivating Silicon Anodes with Hybrid Solid–Electrolyte Interphases

Unlike most anodes used in high energy density batteries, lithiated Si does not form long-lasting passivating solid-electrolyte interphases (SEI) during formation or on charge due to SEI delamination, reconstruction, or dissolution. As a result, electrolyte degradation is continuous and results in a permanent loss of the Li inventory, shortening the useful life of the battery. Here, in this study, we show that perfluoroether electrolyte additives featuring either sulfonyl fluorides or trifluorovinyl ethers, when introduced in prescribed amounts to locally superconcentrated electrolytes, exhibit preferential reactivity at Si during formation due to their higher reduction potential than salts and solvents, creating a hybrid SEI that is simultaneously enriched with LiF and organics tethered to the reactive functionality. While both reactive motifs are effective in creating a hybrid SEI, perfluoroether additives bearing sulfonyl fluorides show more substantial integration. More important, however, is the combined influence of additive topology on anchoring efficacy and tether flexibility between anchoring sites on SEI resiliency. Top-performing Si|LFP cells featuring ditopic additive-enriched SEI improve capacity retention by as much as 45% over 100 cycles when compared to additive-free cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Improved Mechanical Adhesion Enabled by Bilayer Hole Transport Layers in Perovskite Solar Cells

We investigate buried-interface mechanical integrity in metal-halide perovskite half-cells using carbazole-based self-assembled monolayers (SAMs) and bilayer hole transport layers composed of metal oxide underlayers and SAMs. Combining macroscopic and microscopic characterization, we quantify interfacial fracture energy (Gc) and identify delamination pathways. SAM deposition on NiOx increases Gc by approximately 10-fold compared with ITO, highlighting the importance of oxide underlayer selection. To isolate the effect of removing noncovalently bonded SAM molecules, we use vapor-deposited perovskite as a solvent-free model system, decoupling the rinse step inherent to solution processing. Removing loosely bound SAM molecules increases Gc from 0.94 +- 0.08 J.m-2 to 4.82 +- 0.79 J.m-2. These results show that oxide selection and SAM binding quality are both critical for strengthening buried interfaces and designing mechanically robust perovskite solar cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Nano-Engineered Interfaces in Dual-Layer Electrodes for Protonic Ceramic Cells with Enhanced Stability and Kinetics

Enhancing interfacial stability and charge transfer in protonic ceramic cells (PCCs) remains a critical challenge, as structural degradation and interfacial resistance often compromise durability and efficiency. Here, we report a nanoengineered dual-layer oxygen electrode architecture designed to address these limitations by introducing a fine-grained nanoparticle interfacial contact layer beneath a porous catalytic backbone. The nanoscale powders, through enhanced sintering activity, densify into a robust interfacial layer that promotes strong chemical bonding, uniform adhesion, and continuous ionic/electronic pathways with the BCZYYb electrolyte. This hierarchical architecture mitigates delamination, redistributes mechanical stress, and establishes efficient charge and mass transport channels without relying on corrosive surface treatments. Electrochemical evaluation demonstrates that the dual-layer design markedly reduces interfacial polarization resistance and accelerates electrode kinetics. Compared to the single-layer counterpart, the architecture achieves a peel strength of 44.53 N/cm 2 , a 40% improvement in peak power density (0.96 W cm –2 at 600 °C), and a 130% enhancement in electrolysis current density (4.78 A cm –2 at 1.57 V). Faradaic efficiency remains as high as 88% under high steam concentrations, underscoring minimal charge loss during practical operation. Notably, the electrode retains stability across 450–600 °C and under transient voltage cycling, with impedance spectra confirming suppressed interfacial resistance growth over prolonged use. These results highlight nanoscale interface engineering as a powerful route to enhance both mechanical robustness and electrochemical kinetics in PCCs. The demonstrated scalability and durability of this architecture provide a versatile platform for advancing solid-state electrochemical systems, including reversible fuel cells and high-efficiency hydrogen production technologies.

Faradaic efficiency↗