SEARCH · Engineering Papers

Results for “database for model validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Space Transportation System (STS)-133/External Tank (ET)-137 Intertank (IT) Stringer Cracking Issue and Repair Assessment: Proximate Cause Determination and Material Characterization Study

Several cracks were detected in stringers located beneath the foam on the External Tank (ET) following the launch scrub of Space Transportation System (STS)-133 on November 5, 2010. The stringer material was aluminum-lithium (AL-Li) 2090-T83 fabricated from sheets that were nominally 0.064 inches thick. The mechanical properties of the stringer material were known to vary between different material lots, with the stringers from ET-137 (predominately lots 620853 and 620854) having the highest yield and ultimate stresses. Subsequent testing determined that these same lots also had the lowest fracture toughness properties. The NASA Engineering and Safety Center (NESC) supported the Space Shuttle Program (SSP)-led investigation. The objective of this investigation was to develop a database of test results to provide validation for structural analysis models, independently confirm test results obtained from other investigators, and determine the proximate cause of the anomalous low fracture toughness observed in stringer lots 620853 and 620854. This document contains the outcome of the investigation.

Piascik, Robert S.↗

NASA NTRS2019

Technology Readiness Assessment for HEEET TPS

The HEEET project was conceived to develop a heatshield with a high performance ablative thermal protection material that can withstand the extreme entry environment produced as a result of rapid deceleration during high speed entry into Venus, Saturn, Uranus or higher speed entry into Earth's atmosphere. Successful maturation of HEEET supports future New Frontiers and Discovery AO's, as well as Flagship and directed missions in the longer term. In addition, HEEET has the potential to evolve and to support re-entry to Earth, for missions such as Mars Sample Return.The primary goal of the HEEET Project was to develop an ablative TPS heat-shield based on woven TPS technology to Technology Readiness Level (TRL) 6. Key evidence to support the TRL evaluation includes: Demonstration of reproducible manufacturing of a dual layer material over a range of thicknesses and integrated on to a heatshield engineering test unit at a scale that is applicable to near term Discovery as the highest priority and future NF missions as secondary priority set of missions. Demonstration of predictable and stable performance of the dual layer TPS over a range of entry environments that are applicable to near term Discovery and NF missions of interest to SMD.Includes completion of coupon arc jet and laser testing and development of a mid-fidelity thermal response model that correlates with test results. Demonstration of flight heatshield system design for a range of sizes and loads that are relevant to near term Discovery and NF missions of interest to SMD. Includes completion of structural testing to validate analytic thermal/structural models and development of a material property database. Includes structural testing of a ~1m Engineering Test Unit under relevant entry loads.

Gage, Peter↗

NASA NTRSDate not supplied

Deploying a Self-Supervised Learning Based Model to Search Events Across Space and Time

Motivation - Scientific Study of natural events, phenomena, or disasters require examples which span across time and space. - Machine Learning adaptation is on the rise, but there’s a lack of labeled training datasets that could be used to train or validate the models. - Best case scenario: - There’s an event database that tracks events available through time and space. - Provides all data associated with the events. - Real life scenario: - Some events are better tracked than others. - Scientists need to spend significant time identifying and gathering examples of events from different sources.

Iksha Gurung↗

NASA NTRSDate not supplied

Evaluating Meteorological Dust Events and Machine-Learning Based Dust Identification in Geostationary Satellite Imagery

NASA scientists in the Short-term Prediction Research and Transition Center (SPoRT) developed a physically-based machine learning approach to identify dust in satellite imagery with a focus on night-time dust detection (Berndt et al. 201; DustTracker-AI). NASA/NOAA Geostationary Environmental Operational Satellite-16 (GOES-16) imagery was used for training and model inputs. The training, testing and validation data set consists of 28 events in the Southwest United States, capturing dust and null events in the region from 2018-2020.With 83 distinct images and millions of pixels a random forest model was trained and validated, correctly labeling 85% of dust pixels.For the first time, the model was run in near-real time production during the spring of 2022 and dust probability visualizations were made available to NOAA National Weather Service (NWS) forecasters to assess its utility for dust forecasting. Results indicated the model helped increase the confidence in the presence of dust and enabled dust tracking for a longer period of time into the night-time hours. Forecaster assessment and running the model in near real-time allowed for the team to determine the types of events missed, captured, and false alarms. To gain additional context on model performance,the SPoRT team sought to gather more detailed information on the training database(e.g., meteorological characteristics and drivers). The goal of this project was to identify the meteorological drivers for the dust events and create a database which synthesized information from observations, forecaster discussions, and analyses pertaining to the dust events to understand the types of events currently used to train the model. A more detailed meteorological synopsis was created for each dust event in the training, testing, and validation datasets. Following the completion of the database and documentation, the classification details revealed that 88% of the dust events were synoptically driven while mesoscale events were less prevalent in model datasets. Meteorological conditions found such as mixing layer depth and wind velocity had mean values of 645mb and 21kt respectively.With conditions of deep mixed layers and moderate to strong surface winds a mesoscale thunderstorm outflow event was considered and subsequently added to the model training data set to test the impact of additional mesoscale training data. The model was retrained and then qualitatively tested on a sample thunderstorm outflow case that the original model was unable to identify. Preliminary results showed potential that the addition of more mesoscale events included in the training data could help to better identify indistinct and localized dust events.

Connor Welch↗

NASA NTRSDate not supplied

Implementation of A New Microwave Scattering Database and A Forward Model for Active Microwave Sensors in CRTM

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. CRTM is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk scattering lookup tables in order to perform all-sky RT calculations. However, the current CRTM lookup tables for microwave frequencies were generated based on the Mie theory by assuming spherical frozen particles. The scattering lookup tables generated using the DDA technique has shown to largely improve the RT scattering calculations in the MW region. This presentation targets (i) the implementation and validation of a DDA database that was originally developed for the ARTS RT model into CRTM, and (ii) developing the CRTM active sensor module that takes advantage of the backscattering coefficients computed using the DDA method. The DDA database only provides single scattering properties of different habits, while CRTM requires bulk scattering properties. The CRTM cloud coefficients were previously generated based on the effective radius for representing the size of the particles. However, effective radius is neither measurable nor provided by the NWP models, thus need to be estimated from other geophysical variables such as water content. Therefore, in addition to calculating the CRTM bulk scattering properties from the DDA single scattering database, the CRTM was also largely modified to use cloud water content (kg.m-3), instead of effective radius, for performing the interpolation over size/mass of the particles. CRTM already requires water content as input, thus no extra variables are required for performing scattering calculations using the new ARTS DDA database. The CRTM scattering modules search for effective radius in cloud coefficient files and will use the cloud water content if the effective radius dimension is not found in the cloud coefficient files. Figure 1 shows the CRTM simulated brightness temperatures computed using different cloud coefficients versus ATMS observed values over Hurricane Irma on September 7, 2017 at 18:00 UTC. We used all the cloud water content values included in ERA5 with default CRTM/DDA habits for water, rain, snow, ice, hail, and graupel. ERA5 does not provide separate water content values for ice, hail, and graupel, thus the ice water content values were divided between ice, hail, and graupel clouds similar to what was explained in the previous section. In channels with a frequency lower than 90 GHz, emission from water and rain clouds can compensate for cloud scattering so that cloud contaminated Tbs are larger than corresponding clear sky Tbs. The DDA simulations for channels 1-7 largely perform better than the Mie simulations. The DDA simulations show a mix of small negative and positive simulated minus observed values, while the Mie results show large negative biases. The weighting functions for some of the ATMS temperature sounding channels (channels 9-15) peak mostly above the clouds, therefore the measured Tbs become less sensitive to clouds so that the results of both Mie and DDA become very similar. The Mie lookup tables generate excessive scattering for channel 16, but not enough scattering for the water vapor channels. In the specific case of Hurricane Maria, the DDA lookup tables do not generate enough scattering for channel 16, but the DDA results are much more consistent with observations for water vapor channels than for channel 16. It should be noted that the results may vary if we use other habits to represent snow, hail, and graupel in the DDA simulations. Although these results clearly show the advantage of the DDA database over the Mie dataset, different error sources such as error in the observations, displacement of clouds in the ERA5 reanalysis, and also lack of convective clouds or in general errors in the input atmospheric and cloud profiles contribute to the differences between the simulated and observed values. Aside from the improvements in the simulations, a major advantage of the new dataset is a large number of habits that can be used to tune the data assimilation systems to perform well in different weather conditions.

Isaac Moradi↗

NASA NTRS2007

Optical Measurements in a Combustor Using a 9-Point Swirl-Venturi Fuel Injector

This paper highlights the use of two-dimensional data to characterize a multipoint swirl-venturi injector. The injector is based on a NASA-conceived lean direct injection concept. Using a variety of advanced optical diagnostic techniques, we examine the flows resultant from multipoint, lean-direct injectors that have nine injection sites arranged in a 3 x 3 grid. The measurements are made within an optically-accessible, jet-A-fueled, 76-mm by 76-mm flame tube combustor. Combustion species mapping and velocity measurements are obtained using planar laser-induced fluorescence of OH and fuel, planar laser scatter of liquid fuel, chemiluminescence from CH*, NO*, and OH*, and particle image velocimetry of seeded air (non-fueled). These measurements are used to study fuel injection, mixedness, and combustion processes and are part of a database of measurements that will be used for validating computational combustion models.

Hicks, Yolanda R.↗

NASA NTRS2001

The Objectives of NASA's Living with a Star Space Environment Testbed

NASA is planning to fly a series of Space Environment Testbeds (SET) as part of the Living With A Star (LWS) Program. The goal of the testbeds is to improve and develop capabilities to mitigate and/or accommodate the affects of solar variability in spacecraft and avionics design and operation. This will be accomplished by performing technology validation in space to enable routine operations, characterize technology performance in space, and improve and develop models, guidelines and databases. The anticipated result of the LWS/SET program is improved spacecraft performance, design, and operation for survival of the radiation, spacecraft charging, meteoroid, orbital debris and thermosphere/ionosphere environments. The program calls for a series of NASA Research Announcements (NRAs) to be issued to solicit flight validation experiments, improvement in environment effects models and guidelines, and collateral environment measurements. The selected flight experiments may fly on the SET experiment carriers and flights of opportunity on other commercial and technology missions. This paper presents the status of the project so far, including a description of the types of experiments that are intended to fly on SET-1 and a description of the SET-1 carrier parameters.

Barth, Janet L.↗

NASA NTRS2005

A Priori Analysis of Subgrid-Scale Models for Large Eddy Simulations of Supercritical Binary-Species Mixing Layers

Models for large eddy simulation (LES) are assessed on a database obtained from direct numerical simulations (DNS) of supercritical binary-species temporal mixing layers. The analysis is performed at the DNS transitional states for heptane/nitrogen, oxygen/hydrogen and oxygen/helium mixing layers. The incorporation of simplifying assumptions that are validated on the DNS database leads to a set of LES equations that requires only models for the subgrid scale (SGS) fluxes, which arise from filtering the convective terms in the DNS equations. Constant-coefficient versions of three different models for the SGS fluxes are assessed and calibrated. The Smagorinsky SGS-flux model shows poor correlations with the SGS fluxes, while the Gradient and Similarity models have high correlations, as well as good quantitative agreement with the SGS fluxes when the calibrated coefficients are used.

turbulence↗

NASA NTRS2006

Flight Acoustic Testing and For the Rotorcraft Noise Data Acquisition Model (RNM)

Two acoustic flight tests have been conducted on a remote test range at Eglin Air Force Base in the panhandle of Florida. The first was the "Acoustics Week" flight test conducted in September 2003. The second was the NASA Heavy Lift Rotorcraft Acoustics Flight Test conducted in October-November 2005. Benchmark acoustic databases were obtained for a number of rotorcraft and limited fixed wing vehicles for a variety of flight conditions. The databases are important for validation of acoustic prediction programs such as the Rotorcraft Noise Model (RNM), as well as for the development of low noise flight procedures and for environmental impact assessments. An overview of RNM capabilities and a detailed description of the RNM/ART (Acoustic Repropagation Technique) process are presented. The RNM/ART process is demonstrated using measured acoustic data for the MD600N. The RNM predictions for a level flyover speed sweep show the highest SEL noise levels on the flight track centerline occurred at the slowest vehicle speeds. At these slower speeds, broadband noise content is elevated compared to noise levels obtained at the higher speeds. A descent angle sweep shows that, in general, ground noise levels increased with increasing descent rates. Vehicle orientation in addition to vehicle position was found to significantly affect the RNM/ART creation of source noise semi-spheres for vehicles with highly directional noise characteristics and only mildly affect those with weak acoustic directionality. Based on these findings, modifications are proposed for RNM/ART to more accurately define vehicle and rotor orientation.

Burley, Casey L.↗

NASA NTRS2006

Flight Acoustic Testing and Data Acquisition For the Rotor Noise Model (RNM)

Two acoustic flight tests have been conducted on a remote test range at Eglin Air Force Base in the panhandle of Florida. The first was the Acoustics Week flight test conducted in September 2003. The second was the NASA Heavy Lift Rotorcraft Acoustics Flight Test conducted in October-November 2005. Benchmark acoustic databases were obtained for a number of rotorcraft and limited fixed wing vehicles for a variety of flight conditions. The databases are important for validation of acoustic prediction programs such as the Rotorcraft Noise Model (RNM), as well as for the development of low noise flight procedures and for environmental impact assessments. An overview of RNM capabilities and a detailed description of the RNM/ART (Acoustic Repropagation Technique) process are presented. The RNM/ART process is demonstrated using measured acoustic data for the MD600N. The RNM predictions for a level flyover speed sweep show the highest SEL noise levels on the flight track centerline occurred at the slowest vehicle speeds. At these slower speeds, broadband noise content is elevated compared to noise levels obtained at the higher speeds. A descent angle sweep shows that, in general, ground noise levels increased with increasing descent rates. Vehicle orientation in addition to vehicle position was found to significantly affect the RNM/ART creation of source noise semi-spheres for vehicles with highly directional noise characteristics and only mildly affect those with weak acoustic directionality. Based on these findings, modifications are proposed for RNM/ART to more accurately define vehicle and rotor orientation.

Conner, David A.↗

NASA NTRS1993

Validated environmental and physiological data from the CELSS Breadboard Projects Biomass Production Chamber. BWT931 (Wheat cv. Yecora Rojo)

This KSC database is being made available to the scientific research community to facilitate the development of crop development models, to test monitoring and control strategies, and to identify environmental limitations in crop production systems. The KSC validated dataset consists of 17 parameters necessary to maintain bioregenerative life support functions: water purification, CO2 removal, O2 production, and biomass production. The data are available on disk as either a DATABASE SUBSET (one week of 5-minute data) or DATABASE SUMMARY (daily averages of parameters). Online access to the VALIDATED DATABASE will be made available to institutions with specific programmatic requirements. Availability and access to the KSC validated database are subject to approval and limitations implicit in KSC computer security policies.

Stutte, G. W.↗

NASA NTRS2018

NASA Observations and Modeling During ICE-POP

Recap: NASA-Specific Objectives for ICE-POP: Provide real-time observational and NWP data in support of ICE-POP, participate in significant international science effort; GPM (Global Precipitation Measurement) Ground Validation and NASA Weather Program -Direct/physical validation of active/passive satellite-based snowfall retrieval algorithms over coastline and mountains; melting layer interaction with terrain -Physics of snow, coupling to snow water equivalent rate and satellite remote sensor retrieval algorithm assumptions - -Size distributions, types/habit, water equivalent, profiles -NU-WRF (NASA-Unified Weather Research and Forecasting) Model plus Observational analyses: Movement toward “level IV products” leverage intensive and multi-faceted NWP (Numerical Weather Prediction) component -Model precipitation processes (liquid, mixed phase and frozen); Build model testing database for further active/passive remote sensing algorithm development (e.g., satellite data simulators) -"Integrated" validation of products in operational context.

Precipitation Science↗

NASA NTRS2013

Experimental Database with Baseline CFD Solutions: 2-D and Axisymmetric Hypersonic Shock-Wave/Turbulent-Boundary-Layer Interactions

A database compilation of hypersonic shock-wave/turbulent boundary layer experiments is provided. The experiments selected for the database are either 2D or axisymmetric, and include both compression corner and impinging type SWTBL interactions. The strength of the interactions range from attached to incipient separation to fully separated flows. The experiments were chosen based on criterion to ensure quality of the datasets, to be relevant to NASA's missions and to be useful for validation and uncertainty assessment of CFD Navier-Stokes predictive methods, both now and in the future. An emphasis on datasets selected was on surface pressures and surface heating throughout the interaction, but include some wall shear stress distributions and flowfield profiles. Included, for selected cases, are example CFD grids and setup information, along with surface pressure and wall heating results from simulations using current NASA real-gas Navier-Stokes codes by which future CFD investigators can compare and evaluate physics modeling improvements and validation and uncertainty assessments of future CFD code developments. The experimental database is presented tabulated in the Appendices describing each experiment. The database is also provided in computer-readable ASCII files located on a companion DVD.

Database↗

NASA NTRS1994

Supersonic and hypersonic shock/boundary-layer interaction database

An assessment is given of existing shock wave/tubulent boundary-layer interaction experiments having sufficient quality to guide turbulence modeling and code validation efforts. Although the focus of this work is hypersonic, experiments at Mach numbers as low as 3 were considered. The principal means of identifying candidate studies was a computerized search of the AIAA Aerospace Database. Several hundred candidate studies were examined and over 100 of these were subjected to a rigorous set of acceptance criteria for inclusion in the data-base. Nineteen experiments were found to meet these criteria, of which only seven were in the hypersonic regime (M is greater than 5).

Settles, Gary S.↗

NASA NTRS1992

A database of aerothermal measurements in hypersonic flow for CFD validation

This paper presents an experimental database selected and compiled from aerothermal measurements obtained on basic model configurations on which fundamental flow phenomena could be most easily examined. The experimental studies were conducted in hypersonic flows in 48-inch, 96-inch, and 6-foot shock tunnels. A special computer program was constructed to provide easy access to the measurements in the database as well as the means to plot the measurements and compare them with imported data. The database contains tabulations of model configurations, freestream conditions, and measurements of heat transfer, pressure, and skin friction for each of the studies selected for inclusion. The first segment contains measurements in laminar flow emphasizing shock-wave boundary-layer interaction. In the second segment, measurements in transitional flows over flat plates and cones are given. The third segment comprises measurements in regions of shock-wave/turbulent-boundary-layer interactions. Studies of the effects of surface roughness of nosetips and conical afterbodies are presented in the fourth segment of the database. Detailed measurements in regions of shock/shock boundary layer interaction are contained in the fifth segment. Measurements in regions of wall jet and transpiration cooling are presented in the final two segments.

Holden, M. S.↗

NASA NTRS1999

Flight Data Reduction of Wake Velocity Measurements Using an Instrumented OV-10 Airplane

A series of flight tests to measure the wake of a Lockheed C- 130 airplane and the accompanying atmospheric state have been conducted. A specially instrumented North American Rockwell OV-10 airplane was used to measure the wake and atmospheric conditions. An integrated database has been compiled for wake characterization and validation of wake vortex computational models. This paper describes the wake- measurement flight-data reduction process.

Vicroy, Dan D.↗

NASA NTRS2010

Cavitation, Flow Structure and Turbulence in the Tip Region of a Rotor Blade

Objectives: Measure the flow structure and turbulence within a Naval, axial waterjet pump. Create a database for benchmarking and validation of parallel computational efforts. Address flow and turbulence modeling issues that are unique to this complex environment. Measure and model flow phenomena affecting cavitation within the pump and its effect on pump performance. This presentation focuses on cavitation phenomena and associated flow structure in the tip region of a rotor blade.

Wu, H.↗

NASA NTRS2008

NASA's Cryogenic Fluid Management Technology Project

The Cryogenic Fluid Management (CFM) Project's primary objective is to develop storage, transfer, and handling technologies for cryogens that will support the enabling of high performance cryogenic propulsion systems, lunar surface systems and economical ground operations. Such technologies can significantly reduce propellant launch mass and required on-orbit margins, reduce or even eliminate propellant tank fluid boil-off losses for long term missions, and simplify vehicle operations. This paper will present the status of the specific technologies that the CFM Project is developing. The two main areas of concentration are analysis models development and CFM hardware development. The project develops analysis tools and models based on thermodynamics, hydrodynamics, and existing flight/test data. These tools assist in the development of pressure/thermal control devices (such as the Thermodynamic Vent System (TVS), and Multi-layer insulation); with the ultimate goal being to develop a mature set of tools and models that can characterize the performance of the pressure/thermal control devices incorporated in the design of an entire CFM system with minimal cryogen loss. The project does hardware development and testing to verify our understanding of the physical principles involved, and to validate the performance of CFM components, subsystems and systems. This database provides information to anchor our analytical models. This paper describes some of the current activities of the NASA's Cryogenic Fluid Management Project.

Tramel, Terri L.↗