Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “corn stover lignin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Unveiling Feedstock Variability: Insights into Corn Stover Conversion - Part I: Physicochemical Properties and Self-Degradation

Transforming agricultural waste into biofuels and bioproducts is crucial to advancing a low-carbon bioeconomy. However, the inherent variability in the composition and quality introduces uncertainties in the conversion efficiency and poses challenges in process development. Through integrating a high-throughput conversion system, material characterization techniques, and advanced data analysis tools, this study investigates the variability of corn stover and its subsequent impacts on carbohydrate conversion. The findings reveal that indoor storage substantially reduces the moisture and ash content and soil contamination, while other properties remain largely unchanged. Self-degradation due to microbial activity during storage decreases the carbohydrate content of corn stover but enhances glucose and xylose yields. A negative correlation is observed between sugar yields and lignin content across samples with varying ash and moisture content. The inhibitory effect of lignin diminishes in self-degraded samples likely due to the disrupted cell wall structure. Although self-degradation slightly increases cellulose crystallinity, no strong correlation was observed between the crystallinity and sugar yield. Hot water pretreatment under mild conditions effectively mitigates inherent variability, consistently improving the sugar yield from corn stover by up to 50%. By elucidating the feedstock variability and its impact on convertibility, these findings offer valuable insights into appropriate feedstock handling and management, highlighting potential strategies to address variability challenges.

09 BIOMASS FUELS↗
DOE OSTI2020

Enhancing Enzyme-Mediated Hydrolysis of Mechanical Pulps by Deacetylation and Delignification

Alkaline induced deacetylation of the hemicellulose combined with subsequent mechanical refining enhanced the enzyme-mediated hydrolysis of pretreated corn stover. The addition of either NaOH (80 °C) or mild KOH (25 °C) to corn stover prior to mechanical refining led to greater than 80% deacetylation with the NaOH treatment also solubilizing low-molecular-weight lignin that was enriched in $β$-O-4 linkages with more than 25% and 13% of the total and surface lignin removed, respectively. Furthermore, the influence of deacetylation and delignification were further enhanced when NaOH was supplemented with 3% Na 2 SO 3 , resulting in 100% deacetylation, 34% delignification, and a >20% increase in the hydrolysis yield of the substrate xylan. A milder KOH treatment resulted in the retention of more than 95% of the lignin within the cellulose rich, water-insoluble fraction with no apparent change in the surface lignin. However, both methods resulted in enhanced xylan hydrolysis when treated with xylanases, suggesting that deacetylation had enhanced accessibility to the xylan present in the pretreated of corn stover. It was apparent that cellulose accessibility was also enhanced by partial delignification, as NaOH treatment resulted in a 65% and 43% increase in the Water Retention Value and Directed Orange dye adsorption, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A combination of deep eutectic solvent and ethanol pretreatment for synergistic delignification and enhanced enzymatic hydrolysis for biorefinary process

Here, a novel pretreatment system containing deep eutectic solvents and ethanol (DES-E) for synergistic carbohydrate conversion and delignification was reported in this study. The DES-E pretreatment resulted in an enhanced glucose yield compared to individual DES and ethanol pretreatment for the three tested biomass, including Broussonetia papyrifera, corn stover and pine. To further explore the delignification mechanism, the solubilized lignin and residual lignin from Broussonetia papyrifera was recovered and extracted, then thoroughly characterized. The highest total OH content was found in the DES-E solubilized lignin, which could be used as antioxidant. The presence of ethanol in pretreatment liquor could protect the β-O-4 substructure from breakage and reduce lignin condensation, which favors the subsequent enzymatic hydrolysis. Comparable glucose yield and delignification performance was achieved by recycled DES. DES-E pretreatment offers a promising method for lignin isolation and cellulose digestibility improvement simultaneously.

09 BIOMASS FUELS↗
DOE OSTI2020

Production of levulinic acid and biocarbon electrode material from corn stover through an integrated biorefinery process

To overcome the inefficient biomass conversion, waste generation, and lack of co-production in biorefineries, an integrated process was proposed for the conversion of corn stover into levulinic acid and biocarbon electrode material. Corn stover was pretreated through hydrothermal process using 0.45 wt% K 2 CO 3 which removed 76 wt% lignin and 85 wt% xylan while preserving 83 wt% glucan. This was followed by acid hydrolysis to produce levulinic acid at varying H 2 SO 4 concentrations and reaction time in a batch reactor at 190 °C. At a reaction time of 5 min in 2 wt% H 2 SO 4 , 35.8 wt% and 30 wt% glucan in raw and pretreated corn stover was converted to levulinic acid, respectively. The residue from acid hydrolysis was converted into biocarbon for supercapacitor electrodes via a two-step thermal activation process which showed a specific capacitance of 120 F g -1 . The proposed integrated biorefinery concept provides multiple value-added products for a greater financial and environmental sustainability.

09 BIOMASS FUELS↗
DOE OSTI2023

Factors that influence the activity of biomass-degrading enzymes in the presence of ionic liquids—a review

Ionic liquids (ILs) are seen as a more sustainable alternative to volatile organic solvents that are accelerating innovations in many industries such as energy storage, separations, and bioprocessing. The ability to effectively deconstruct lignocellulosic biomass is a significant hurdle in the biorefining/bioprocessing industry and presents limitations towards the commercial production of bioproducts (such as biofuels, biomaterials, etc. ). Certain ILs have been shown to promote effective lignin removal, cellulose recovery, and sugar yields from various biomass feedstocks such as corn stover, wheat straw, sugarcane bagasse, sorghum, switchgrass, miscanthus, poplar, pine, eucalyptus, and certain mixtures of municipal solid waste. However, these improvements are often counteracted by the limited biocompatibility of ILs, which results in an IL-induced reduction in enzyme activity and stability—an important downstream step in the conversion of biomass to biofuels/bioproducts. As a result, significant efforts have been made to discover and engineer compatible enzyme-IL systems and to improve our understanding on the effect that these ILs have on these systems. This review seeks to examine the impact of ionic liquids on enzymes involved in lignocellulosic biomass deconstruction, with a specific focus on their relevance in the context of pretreatment. Beyond presenting an overview of the ionic liquid pretreatment landscape, we outline the main factors that influence enzyme activity and stability in the presence of ILs This data is consolidated and analyzed to apply this body of knowledge towards new innovations that could lead to improvements in the processing of biomass to biofuels and bioproducts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Biorefinery upgrading of herbaceous biomass to renewable hydrocarbon fuels, Part 2: Air pollutant emissions and permitting implications

The development of advanced biofuel production facilities is still at a nascent stage, and the biorefineries could face challenges in obtaining air permits required for their construction and operation because they are novel emission sources. To fill gaps in knowledge regarding potential emissions, we perform a detailed federal regulatory analysis and estimate air pollutant emissions for an advanced biorefinery that produces renewable diesel blendstock (RDB) from lignocellulosic biomass via aerobic respiration documented in Part 1 of the paper. We evaluate 12 design permutations that include two feedstocks, a uniform format blend (UFB) and corn stover; three biorefinery scales, 2,000, 5,200, and 9,100 dry metric tons per day (dmtd) of lignocellulosic biomass feed; and two lignin uses, as either a boiler fuel or for pellet production. We also evaluate 6 additional design permutations by incorporating non-emitting renewable power, which could reduce up to 63% carbon monoxide (CO) and nitrogen oxides (NO x ) each, 21% volatile organic compounds (VOC), and 43% hazardous air pollutants (HAP) as opposed to on-site power production, for biorefineries that produce pellets, using either UFB or corn stover. Our results indicate that all 18 design permutations would be classified as a major source under the Clean Air Act's New Source Review program without additional emission controls. Compared to using lignin as a boiler fuel, diverting lignin for pellet production reduces the emissions of CO up to 88%, NOx up to 73%, sulfur dioxide (SO 2 ) up to 99%, VOCs up to 72%, and HAPs up to 66%. Additionally, we explore control options that could further reduce emissions and assess whether reductions are enough to achieve minor source classification. Insights from our analysis can help biorefinery developers and regulators develop permitting strategies to mitigate investment risks.

09 BIOMASS FUELS↗
DOE OSTI2021

The role of catalytic iron in enhancing volumetric sugar productivity during autothermal pyrolysis of woody biomass

Passivation of naturally occurring AAEM in biomass enhances sugar yields from the fast pyrolysis of biomass by preventing these metals from catalyzing the fragmentation of pyranose rings in cellulose and hemicellulose. However, because AAEM also catalyzes lignin depolymerization, its passivation can be accompanied by undesirable char agglomeration. Pretreatment of biomass with ferrous sulfate both passivates AAEM and substitutes ferrous ions as lignin depolymerization catalysts. This pretreatment has been particularly successful for high ash biomass like corn stover, but of limited value for low ash biomass like wood. This study explores the reasons for this discrepancy and offers a combined pretreatment of ferrous sulfate and ferrous acetate pretreatment to overcome char agglomeration in wood. Furthermore, this new pretreatment increased sugar yields from 4.4 wt% to 15.5 wt% and 5.4 wt% to 19.0 wt% for hardwood and softwood biomasses, respectively. This pretreatment produces an iron-rich biochar that catalyzes oxidation of the biochar under the oxygen-rich conditions of autothermal pyrolysis, which is preferentially consumed to provide the enthalpy for pyrolysis, preserving bio-oil as a more desirable energy product. Instead of producing carbon monoxide, which dominates oxidation of biochar from untreated biomass, the iron catalyzes oxidation to carbon dioxide, producing more energy per mole of oxygen consumed. In fact, oxygen demand to support autothermal pyrolysis of red oak and southern yellow pine was reduced 15% by the presence of iron in the biochar.

42 ENGINEERING↗
DOE OSTI2020

Ammonia-salt solvent promotes cellulosic biomass deconstruction under ambient pretreatment conditions to enable rapid soluble sugar production at ultra-low enzyme loadings

In this paper, we report a novel ammonia : ammonium salt solvent based pretreatment process that can rapidly dissolve crystalline cellulose into solution and eventually produce highly amorphous cellulose under near-ambient conditions. Pre-activating the cellulose I allomorph to its ammonia–cellulose swollen complex (or cellulose III allomorph) at ambient temperatures facilitated rapid dissolution of the pre-activated cellulose in the ammonia-salt solvent ( i.e. , ammonium thiocyanate salt dissolved in liquid ammonia) at ambient pressures. For the first time in reported literature, we used time-resolved in situ neutron scattering methods to characterize the cellulose polymorphs structural modification and understand the mechanism of crystalline cellulose dissolution into a ‘molecular’ solution in real-time using ammonia-salt solvents. We also used molecular dynamics simulations to provide insight into solvent interactions that non-covalently disrupted the cellulose hydrogen-bonding network and understand how such solvents are able to rapidly and fully dissolve pre-activated cellulose III. Importantly, the regenerated amorphous cellulose recovered after pretreatment was shown to require nearly ~50-fold lesser cellulolytic enzyme usage compared to native crystalline cellulose I allomorph for achieving near-complete hydrolytic conversion into soluble sugars. Lastly, we provide proof-of-concept results to further showcase how such ammonia-salt solvents can pretreat and fractionate lignocellulosic biomass like corn stover under ambient processing conditions, while selectively co-extracting ~80–85% of total lignin, to produce a highly digestible polysaccharide-enriched feedstock for biorefinery applications. Unlike conventional ammonia-based pretreatment processes ( e.g. , Ammonia Fiber Expansion or Extractive Ammonia pretreatments), the proposed ammonia-salt process can operate at near-ambient conditions to greatly reduce the pressure/temperature severity necessary for conducting effective ammonia-based pretreatments on lignocellulose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Thermophilic Geobacillus WSUCF1 Secretome for Saccharification of Ammonia Fiber Expansion and Extractive Ammonia Pretreated Corn Stover

A thermophilic Geobacillus bacterial strain, WSUCF1 contains different carbohydrate-active enzymes (CAZymes) capable of hydrolyzing hemicellulose in lignocellulosic biomass. We used proteomic, genomic, and bioinformatic tools, and genomic data to analyze the relative abundance of cellulolytic, hemicellulolytic, and lignin modifying enzymes present in the secretomes. Results showed that CAZyme profiles of secretomes varied based on the substrate type and complexity, composition, and pretreatment conditions. The enzyme activity of secretomes also changed depending on the substrate used. The secretomes were used in combination with commercial and purified enzymes to carry out saccharification of ammonia fiber expansion (AFEX)-pretreated corn stover and extractive ammonia (EA)-pretreated corn stover. When WSUCF1 bacterial secretome produced at different conditions was combined with a small percentage of commercial enzymes, we observed efficient saccharification of EA-CS, and the results were comparable to using a commercial enzyme cocktail (87% glucan and 70% xylan conversion). It also opens the possibility of producing CAZymes in a biorefinery using inexpensive substrates, such as AFEX-pretreated corn stover and Avicel, and eliminates expensive enzyme processing steps that are used in enzyme manufacturing. Implementing in-house enzyme production is expected to significantly reduce the cost of enzymes and biofuel processing cost.

Bhalla, Aditya↗
DOE OSTI2023

Liquefaction of different corn stover fractions assisted by enzyme-biomass deconstruction

Recalcitrant properties of different sources of lignocellulosic biomass represent challenges in materials processing within a biorefinery, as well as enzyme efficient deconstruction to fermentable sugars. Limitations include lignin derived enzyme inhibitors, enzyme inhibition by hydrolysis products, and resistance to mixing due to rheological properties of lignocellulosic particulates at high solids loadings. Consequently, we examined conditions that might be used to achieve liquid slurries (i.e., liquefaction) at solids loadings of 300 g/L before the material enters the biorefinery through a pretreatment step. This work explores enzyme-assisted liquefaction in a fed-batch process using the commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids, basis. Corn stover pellets were fed into a 1 L stirred bioreactor containing enzyme solution over a 5-hour period until reaching 30% solids loading (dry wgt / vol basis). After 6, 24 and 96 hours from the start of the run, samples were taken and characterized with respect to their sugar composition, rheology, water absorption and enzyme activity. Slurries with dramatically reduced yield stresses were achieved for corn stover. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme.Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours.A profile based on 6, 24 and 96h of yield stress measurements and sugar conversion is presented. Enzyme activity is measured and the impact of liquefaction on an integrated processing in a biorefinery operation is discussed.

Gutierrez, Diana↗
DOE OSTI2021

Techno-Economic Assessment for the Production of Hydrocarbon Fuels via Catalytic Upgrading of Furans

This technical report documents the techno-economic analysis (TEA) implications of a biochemical/catalytic pathway for the production of long-chain hydrocarbon fuels in support to the multi-lab Catalytic Upgrading of Biochemical Intermediates (CUBI) project within the Chemical Catalysis for Bioenergy Consortium (ChemCatBio). Two distinct conceptual biorefineries centered around the process encompassing sugar dehydration to furans, aldol condensation between furans and a ketone (methyl ethyl ketone [MEK]), and a final step of hydrotreating to obtain hydrocarbons in the C 14 -C 16 range are considered: an integrated plant that simultaneously produces both furans (furfural and HMF) and ketone (MEK via 2,3-butanediol [BDO]) from sugars and a dedicated facility focused on producing furans from corn stover hydrolysate and procuring the ketone externally. In either plant, the main coproducts are adipic acid (derived from lignin) and sodium sulfate. The results from the assessment are quite comparable to those reported in previous design case focused on biological conversion of sugars to fermentation intermediates with subsequent catalytic upgrading of those intermediates to hydrocarbon fuels, thus presenting another viable alternative pathway to achieve similar fuel cost targets through purely catalytic upgrading of sugars. Since this study considers long-term performance targets for the full pathway dedicated to sugar upgrading to fuels, the critical remaining research points needed to achieve future cost goals are also discussed. Finally, this report presents a single-point sensitivity analysis around selected parameters to identify the major cost drivers of the biorefineries and provides a qualitative discussion on additional opportunities for cost reduction within the proposed concepts, namely through adding value to furans, to coproducts that may be obtained following BDO dehydration, and to lignin through alternative pathways.

09 BIOMASS FUELS↗
DOE OSTI2024

Feedstock/pretreatment screening for bioconversion of sugar and lignin streams via deacetylated disc-refining

Recent publications have shown the benefits of deacetylation disc-refining (DDR) as a pretreatment process to deconstruct biomass into sugars and lignin residues. Major advantages of DDR pretreatment over steam and dilute acid pretreatment are the removal of acetyl and lignin during deacetylation. DDR does not generate hydroxymethylfurfural (HMF) and furfural which are commonly produced from steam and dilute acid pretreatments. Acetate, lignin, HMF, and furfural are known inhibitors during enzymatic hydrolysis and fermentation. Another advantage of deacetylation is the production of lignin-rich black liquor, which can be upgraded to other bioproducts. Furthermore, due to the lack of sugar degradation during deacetylation, DDR has significantly less sugar loss than other pretreatment methods. Previous studies for DDR have primarily focused on corn stover, but lacked the investigative studies of other feedstocks. This study was designed to screen various DDR process conditions at pilot scale using three different feedstocks, including corn stover, poplar, and switchgrass. The impact of the pretreatment conditions was evaluated by testing hydrolysates for bioconversion to 2,3-butanediol. Pretreatment of biomass by DDR showed high-conversion-yields and 2,3-BDO fermentation production yields. Techno-economic analysis (TEA) of the pretreatment for biomass to sugar was also developed based on NREL’s Aspen Model. This study shows that the cellulose and hemicellulose in poplar was more recalcitrant than herbaceous feedstocks which ultimately drove up the sugar cost. Switchgrass was also more recalcitrant than corn stover but less than poplar.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Comparison of methodologies used to determine aromatic lignin unit ratios in lignocellulosic biomass

Abstract Background Multiple analytical methods have been developed to determine the ratios of aromatic lignin units, particularly the syringyl/guaiacyl (S/G) ratio, of lignin biopolymers in plant cell walls. Chemical degradation methods such as thioacidolysis produce aromatic lignin units that are released from certain linkages and may induce chemical changes rendering it difficult to distinguish and determine the source of specific aromatic lignin units released, as is the case with nitrobenzene oxidation methodology. NMR methods provide powerful tools used to analyze cell walls for lignin composition and linkage information. Pyrolysis-mass spectrometry methods are also widely used, particularly as high-throughput methodologies. However, the different techniques used to analyze aromatic lignin unit ratios frequently yield different results within and across particular studies, making it difficult to interpret and compare results. This also makes it difficult to obtain meaningful insights relating these measurements to other characteristics of plant cell walls that may impact biomass sustainability and conversion metrics for the production of bio-derived fuels and chemicals. Results The authors compared the S/G lignin unit ratios obtained from thioacidolysis, pyrolysis-molecular beam mass spectrometry (py-MBMS), HSQC liquid-state NMR and solid-state (ss) NMR methodologies of pine, several genotypes of poplar, and corn stover biomass. An underutilized approach to deconvolute ssNMR spectra was implemented to derive S/G ratios. The S/G ratios obtained for the samples did not agree across the different methods, but trends were similar with the most agreement among the py-MBMS, HSQC NMR and deconvoluted ssNMR methods. The relationship between S/G, thioacidolysis yields, and linkage analysis determined by HSQC is also addressed. Conclusions This work demonstrates that different methods using chemical, thermal, and non-destructive NMR techniques to determine native lignin S/G ratios in plant cell walls may yield different results depending on species and linkage abundances. Spectral deconvolution can be applied to many hardwoods with lignin dominated by S and G units, but the results may not be reliable for some woody and grassy species of more diverse lignin composition. HSQC may be a better method for analyzing lignin in those species given the wealth of information provided on additional aromatic moieties and bond linkages. Additionally, trends or correlations in lignin characteristics such as S/G ratios and lignin linkages within the same species such as poplar may not necessarily exhibit the same trends or correlations made across different biomass types. Careful consideration is required when choosing a method to measure S/G ratios and the benefits and shortcomings of each method discussed here are summarized.

09 BIOMASS FUELS↗
DOE OSTI2026

Biochemical Conversion of Herbaceous Biomass to Renewable Diesel: Biorefinery Marginal Air Quality Impacts and Comparison to Feedstock Production

This study assesses the air quality impacts of an advanced biorefinery that produces renewable diesel blendstock (RDB) from lignocellulosic biomass via aerobic respiration (Davis et al. 2022) by estimating fine particulate matter (PM2.5) impacts from biorefinery emissions. It continues a prior analysis that used a geospatial assessment to identify source regions for biomass feedstocks and studied the impact of feedstock production emissions on air quality (Thind et al. 2022). Thind et al. (2022) identified RDB biorefineries that can use corn stover feedstocks of 2,000; 5,200; and 9,100 dry metric tons per day (DMT/day), based in Iowa, and suggested 7 unique counties can serve as hosts for a biorefinery that draws biomass feedstock from neighboring counties. Given 13 unique county-biorefinery size combinations and two waste lignin end uses at the biorefinery (lignin as a fuel for electricity generation and lignin for pellet production), the air-quality-related sustainability aspects of each of these 26 scenarios are assessed by estimating the annual average impacts of biorefinery emissions on the dispersion and formation of secondary PM2.5 in the atmosphere using a novel reduced-complexity air quality model called the Intervention Model for Air Pollution (InMAP). The 26 biorefinery design combinations help capture how a biorefinery's emissions of air pollutants and their resulting impact on local and regional air quality are influenced by the magnitude of production scale, lignin utilization strategy, and location of a proposed biorefinery. Methods developed in Thind et al. (2022) are applied to estimate the constraints on primary PM2.5 and secondary PM2.5 precursor emissions based on compliance with U.S. Environmental Protection Agency's (EPA's) annual primary National Ambient Air Quality Standard (NAAQS) of PM2.5 (i.e.12.0 micrograms per cubic meter (microgram/m3)) at downwind receptors of a biorefinery. Incremental PM2.5 concentrations caused by the emission of biorefining corn stover into RDB are assessed and compared to those of corn stover production. To illuminate which upstream supply chain stage of renewable diesel production contributes most to air quality impacts, marginal PM2.5 concentrations are compared between both stages at multiple downwind air quality monitor locations. In addition, through a hotspot analysis, we identify the primary contributing factors of emissions within the feedstock production and biorefinery stage operations. In doing so, we provide insights for improving the air pollutant emission-related sustainability of advanced lignocellulosic biofuel production.

09 BIOMASS FUELS↗
DOE OSTI2022

Liquefaction of pelleted corn cobs

Liquid slurries at high loadings (pumpable slurries) are critical to handle the streams between the unit operations in a biorefinery. Their liquefaction potential was initially tested with a small-scale method using 3FPU Ctec-2 /g dry biomass, and results were confirmed in 1L bioreactors experiments. Liquid slurries of cobs were observed in small scale tests (based on visual appearance, and reducing sugars released). Results were confirmed in 1L bioreactors under similar experimental conditions. Yield stress value in bioreactor was 34 ± 6Pa at 96 h, and glucan and xylan conversion to glucose and xylose, respectively, were 41 and 21%. In addition, work has been initiated with liquefaction of other pelleted corn stover fractions: Husk/Leaf (A),Husk (B), Stems (D) and controls (whole corn stover; F and G). Compositional analysis of the pellets showed glucan content (%) in the samples ranged from 31.9 to 36.1, xylan from 19.1 to 20.9, total lignin 13.1 to 18.8,and total ash 1.73 to 10.19. The moisture content ranged from 6.21 to 11.66%. Given these similar characteristics, we also examined liquefaction of these other samples, and they also showed that liquid slurries are possible. Work is continuing to define favourable conditions for liquid slurries formation.

Cruz, Antonio↗
DOE OSTI2025

Engineered Accumulation of Protocatechuate in Corn Biomass to Enhance Biomanufacturing

The in-planta accumulation of coproducts in crops can enhance the value of lignocellulosic biomass and facilitate a sustainable bioeconomy. Corn stover represents a major renewable source of lignocellulose for the production of advanced biofuels and bioproducts. In this study, we engineered corn with a bacterial gene encoding a dehydroshikimate dehydratase (QsuB) to overproduce protocatechuate (DHBA). Transgenic corn lines accumulate up to 2.9% DHBA on a dry weight basis in leaf and stem biomass. DHBA occurs in the form of glucosides that are extractable from biomass using aqueous methanol as the solvent. The analysis of lignin did not show any evidence for the incorporation of DHBA; however, an increase in the lignin syringyl to guaiacyl ratio and a higher relative abundance of p-coumarate groups compared with total lignin units were observed in QsuB-modified corn. Alkaline hydrolysates prepared from QsuB corn were enriched in DHBA compared to the hydrolysates obtained from wild-type biomass, which contained mostly p-coumarate and ferulate. Using engineered Novosphingobium aromaticivorans as a production host, a 375% improvement in 2-pyrone-4,6-dicarboxylate titers was achieved through biological upgrading of alkaline hydrolysates derived from QsuB corn compared to unmodified biomass. Our data demonstrate an engineering strategy to overproduce DHBA in corn that can facilitate sustainable manufacturing of other valuable bioproducts using stover as a feedstock.

2-pyrone-4,6-dicarboxylate↗
DOE OSTI2026

Feedstock/Pretreatment Screening for Bioconversion of Sugars and Lignin Residues

This project will conduct biomass deconstruction (pretreatment and enzymatic saccharification) on two representative biomass feedstocks and four different pretreatment processes, including three high temperature steam/chemical pretreatments and one low temperature chemical/mechanical pretreatment. A third biomass feedstock will undergo biomass deconstruction with three different pretreatment processes, including two high temperature chemical pretreatments and one low temperature chemical/mechanical pretreatment. Several pretreatment conditions will be performed in a screening study using NLR pilot-scale pretreatment equipment to generate a range of pretreated biomass substrates. A selected number of these substrates will be chosen for enzymatic saccharification evaluation, based on standard compositional analysis of the pretreated substrates as a primary indicator of pretreatment efficacy. Resulting enzymatic hydrolysis slurries will be analyzed to determine overall biomass sugar yields. Additional compositional analysis will be performed to determine oligomeric sugar composition and structure, to analyze structural characteristics of solids fractions on native, pretreated, and enzymatically saccharified biomass residues for one of the biomass feedstocks, corn stover. The enzymatically saccharified materials will undergo 2,3-butanediol fermentation in a shaker flask as bench scale. Using relevant process performance data collected in these various conversion steps, technoeconomic analysis activities will be performed to compare the economic potential of the various biomass feedstock and pretreatment processes and to identify key economic drivers and sustainability metrics.

09 BIOMASS FUELS↗
DOE OSTI2025

Effects of pH on potassium sulfite based alkali pretreatment of corn stover under mild conditions

Sulfite salt-based alkali pretreatment is increasingly recognized as an effective method for biomass pretreatment under mild temperature conditions. However, the effects of pH on the pretreatment process are not yet fully understood. In this study, the pretreatment of corn stover using potassium sulfite (KS) combined with aqueous ammonia (AA) at 80 °C was investigated within a pH range of 9–14. Results demonstrated that high pH environment established by combining KS with AA is critical for enhancing sulfonation modifications, effectively removing lignin, facilitating deacetylation, and significantly improving the total sugar yield. For example, when comparing KS alone at pH 9.7, AA alone at pH 13, and KS combined with AA at pH 13, the delignification rates were 13.82 %, 67.71 %, and 71.27 %, respectively; the deacetylation rates were 25.84 %, 81.19 %, and 82.54 %, respectively; and the total sugar yields were 24.85 %, 78.96 %, and 92.12 %, respectively. The X-ray photoelectron spectroscopy (XPS) results confirmed that sulfonation reactions occurred under low-temperature and high pH conditions, leading to enhanced delignification efficiency. Results also showed that the cellulase adsorption, water retention, and the enzymatic digestibility of the pretreated solids increased along with rising pH. Moreover, nuclear magnetic resonance (NMR) analysis revealed that KS-based alkali pretreatment retained more β-O-4 native bonds in the pretreated lignin-rich hydrolysate than alkali pretreatment alone did, providing promising opportunities for the subsequent upgrading of lignin into high-value products.

09 BIOMASS FUELS↗