Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “core sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Characterization of basin concrete in support of structural integrity demonstration for extended storage

Concrete core samples from C basin were characterized through material testing and analysis to verify the design inputs for structural analysis of the L Basin and to evaluate the type and extent of changes in the material condition of the concrete under extended service for fuel storage. To avoid the impact on operations, core samples were not collected from L area, but rather, several concrete core samples were taken from the C Basin prior to its closure. C basin was selected due to its similar environmental exposure and service history compared to L Basin. The microstructure and chemical composition of the concrete exposed to the water was profiled from the water surface into the wall to evaluate the impact and extent of exposure. No significant leaching of concrete components was observed. Ingress of carbonation or deleterious species was determined to be insignificant. No evidence of alkali-silica reactions (ASR) was observed. Ettringite was observed to form throughout the structure (in air voids or pores); however, the sulfur content was measured to be consistent with the initial concrete that was used to construct the facility. Similar ettringite trends were observed in the interior segments of the core samples. The compressive strength of the concrete at the mid-wall of the basin was measured, and similar microstructural analysis was conducted on these materials post compression testing. The microstructure was determined to be similar to near-surface segments of the core samples. The average strength was 4148 psi, which is well-above the design strength of 2500 psi. The analyses showed that phase alterations and minor cracking in a microstructure did not affect the design specification for the concrete.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Correlative X-ray micro-nanotomography with scanning electron microscopy at the Advanced Light Source

Geological samples are inherently multi-scale. Understanding their bulk physical and chemical properties requires characterization down to the nano-scale. A powerful technique to study the three-dimensional microstructure is X-ray tomography, but it lacks information about the chemistry of samples. To develop a methodology for measuring the multi-scale 3D microstructure of geological samples, correlative X-ray micro- and nanotomography were performed on two rocks followed by scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS) analysis. The study was performed in five steps: (i) micro X-ray tomography was performed on rock sample cores, (ii) samples for nanotomography were prepared using laser milling, (iii) nanotomography was performed on the milled sub-samples, (iv) samples were mounted and polished for SEM analysis and (v) SEM imaging and compositional mapping was performed on micro and nanotomography samples for complimentary information. Correlative study performed on samples of serpentine and basalt revealed multiscale 3D structures involving both solid mineral phases and pore networks. Significant differences in the volume fraction of pores and mineral phases were also observed dependent on the imaging spatial resolution employed. This highlights the necessity for the application of such a multiscale approach for the characterization of complex aggregates such as rocks. Information acquired from the chemical mapping of different phases was also helpful in segmentation of phases that did not exhibit significant contrast in X-ray imaging. Adoption of the protocol used in this study can be broadly applied to 3D imaging studies being performed at the Advanced Light Source and other user facilities.

58 GEOSCIENCES↗

317/319 phytoremediation site monitoring report - 2004 growing season.

In 1999, Argonne National Laboratory (ANL) designed and installed a series of engineered plantings consisting of a vegetative cover system and approximately 800 hybrid poplars and willows rooting at various predetermined depths. The plants were installed using various methods including Applied Natural Science's TreeWell{reg_sign} system. The goal of the installation was to protect downgradient surface and groundwater by hydraulic control of the contaminated plume by intercepting the contaminated groundwater with the tree roots, removing moisture from the upgradient soil area, reducing water infiltration, preventing soil erosion, degrading and/or transpiring the residual volatile organic compounds (VOCs), and removing tritium from the subsoil and groundwater. This report presents the results of the monitoring activities conducted by Argonne's Energy Systems Division (ES) in the growing season of 2004. Monitoring of the planted trees began soon after the trees were installed in 1999 and has been conducted every summer since then. As the trees grew and consolidated their growth into the contaminated soil and groundwater, their exposure to the contaminants was progressively shown through tissue sampling. Since the inception of the project, significant progress was made in the refinement and testing of the analytical method (for which no official method is available), the determination of the optimal tissue for sampling, and of the variability of the concentrations within a specific tree. An understanding has also been developed on background concentrations of VOCs, and how to discriminate between VOCs that are associated with plant tissue because of aerial or of soil/groundwater uptake pathways. Also, during the 2003 sampling campaign, core samples from tree trunks were collected for the first time (the trees were large enough to stand the procedure). Data collected from the French Drain area last year supported the hypothesis that a correlation was present between concentrations of VOCs in the soil and in corresponding branch tissue. During this year (2004), systematic data collection in the French Drain area further consolidated this correlation and indicated that trees are clearly in the condition to have reached the target rooting depth. Concentrations in the hundreds of ppb in branch and trunk samples confirm that uptake can be a quantitative way to remove VOCs from the contaminated media. Additionally, laboratory studies were conducted in 2004 to determine mass recoveries from leaves and branches using the headspace method, and to determine if we could further modify our sample pretreatment method to ensure optimal recovery. Results showed that the recovery of TCE in leaves and branches with our current method ranged between 98 and 138%, indicating that most of the TCE present in the samples is recovered during the analysis. Freezing and heating had variable results in recovery rates, which resulted in no significant changes being introduced to the current SOP.

54 ENVIRONMENTAL SCIENCES↗

Data Summary Report for Soil and Slab Sampling at Former Building 175

Lawrence Livermore National Security (LLNS) and the U.S. Department of Energy (DOE) are in the process of returning the area where Building 175 existed to beneficial use for future site development. The completed assessment will help LLNS and DOE to outline project scope and costs associated with the removal, characterization, and disposal of materials generated when the concrete slab for the former building and any associated remaining subsurface structures are demolished. Slab removal under the Transition & Disposition process requires full screening for potential site contamination to determine appropriate future land use. Borehole locations and depths were designed to correctly assess DOE’s future liability for characterizing residual vadose zone contamination. If a residual source area is identified at depth, DOE will need to evaluate the additional cost of future subsurface cleanup (with limited access) due to planned development. This is necessary to leave the location in a “ready-to-build” status. As a result, Phase II sampling requirements may in some cases extend beyond the construction zone required for slab removal to ensure the necessary due diligence. To avoid the potential spread of contamination and/or the creation of an environmental release by impacting the integrity of known contamination areas (e.g., pit within room 102 and the east to west boundary seam), these locations were not sampled for this project. During demolition of the slab, these locations and their underlying soils should be further evaluated. The assessment was conducted in accord with the May 2022 Lawrence Livermore National Laboratory Former Building 175 Assessment Soil Sampling and Analysis Plan / Quality Assurance Plan. Thirty-six, direct-push borings were advanced, along with collecting concrete (where present) and soil samples for laboratory analyses. Thirty-two of the borings were advanced to a depth of 25 feet below ground (bgs), and four borings were advanced to a depth of 55 feet bgs. The concrete slab for former Building 175 ranged from approximately 8 inches to over two feet in thickness. Soils encountered during the investigation consisted primarily of clayey silt, with interbeds of sandy gravel and silty sand to the total depth explored of 55 feet bgs. Field photoionization detector readings – checking for volatile organic compound (VOC) vapors in soils, ranged from zero (0) to a peak of 33 parts per million at 25 feet bgs in boring PC-B175- 028. The cause for the peak reading is unknown, however, no visually discolored or odorous soils were encountered during the assessment and all VOC results were below Lawrence Livermore National Laboratory’s (LLNL’s) Soil Screening and Management Plan (SSMP) soil screening levels (SSL). Groundwater was not encountered during the assessment and is expected to occur at roughly 65 feet bgs in the project area. No metals were detected at concentrations of concern in the concrete core samples collected and analyzed. Low gross alpha and beta activity concentrations were detected in the concrete core samples collected and analyzed. The detected activity concentrations would appear to be from naturally occurring radioactive isotopes, i.e., potassium 40, present in the raw materials used to make concrete and not artificially added. Tritium was not detected above the testing laboratory's Method Detection Limit (MDL) in any of the concrete core samples collected and analyzed. The radioactive isotopes - actinium 228, bismuth 214, lead 212, lead 214, potassium 40, radium 226, radium 228, and thallium 208, were detected at low activity concentrations in the concrete core samples analyzed. Based on the detected activity concentrations, the isotopes would appear to be naturally occurring in the raw materials used to make concrete and not artificially added. Acetone – a common laboratory contaminant, was detected in nine of the soil samples collected and analyzed. Concentrations of two other volatile organic compounds (benzene and tetrachloroethene) were detected in five of the soil samples analyzed. All concentrations were below SSLs. Total petroleum hydrocarbons as diesel range organics were detected at 43.9 milligrams per kilogram (mg/kg) in the 20-foot bgs duplicate sample from boring PC-B175-007. Total petroleum hydrocarbons as motor oil were detected at 7.20 mg/kg in the 15-foot bgs routine sample from boring PC-B175-001, and at 20.7 mg/kg in the 20-foot bgs duplicate sample from boring PC-B175-007. The SSL for diesel-range TPHs is 260 mg/kg. LLNL does not have an SSL for motor oil range TPHs. No indications of a release, e.g., visibly stained, or odorous soil, were present at the boring locations. No samples collected contained polychlorinated biphenyls (PCBs) in concentrations above the laboratory reporting limit. Arsenic was detected above its SSL of 8.51 mg/kg in the 25-foot bgs routine sample collected from boring PC-B175-023. Nickel was detected above its SSL of 86.0 mg/kg in the 10-foot bgs routine sample from boing PC-B175-005, the 20-foot bgs routine sample from boring PC-B175-025, and the 25-foot bgs routine sample from boring PC-B175-034. The detected concentrations, however, were well below ten times (10x) their respective STLCs. Gross alpha and/or gross beta were detected above their respective SSL activity concentrations in three routine soil samples. Retesting (two per sample) of the samples showed that the initial reported activity concentrations were anomalous. Tritium was not detected in any of the routine or duplicate soil samples collected and analyzed during the investigation. The radioactive isotopes - actinium 228, bismuth 212 and 214, lead 212 and 214, potassium 40, radium 224, 226 and 228, thallium 208, thorium 234 and uranium, were detected at low activity concentrations in the soil samples analyzed for radioactive constituents. The detected isotopes and their associated activity concentrations are typical of those naturally occurring in the marine-type sedimentary deposits underlying the Livermore Valley. No radiological controls are necessary for the soil evaluated.

54 ENVIRONMENTAL SCIENCES↗

Petrophysical properties of saprolites from the Oak Ridge Integrated Field Research Challenge site, Tennessee

At the Oak Ridge Integrated Field Research Challenge site, near Oak Ridge, Tennessee, the shallow saprolitic aquifer is contaminated by nitric acid, uranium, and metals originating from the former S3 settling ponds. To interpret low-frequency geophysical methods used to image contaminant plumes, we have characterized the petrophysical properties of three representative saprolite core samples. Their hydraulic conductivity ranges from to in agreement with field data. Complex conductivity measurements, in the frequency range of 1 mHz to 45 kHz, were performed with NaCl solutions with electrical conductivities in the range to , a range representative of field conditions. The electrical conductivity data were well reproduced with a simple linear conductivity model between the saprolite conductivity and the pore water conductivity. The conductivity plots were used to estimate the formation factor (the cementation exponent was about ) and the surface conductivity ( ). The magnitude of the surface conductivity depended on the degree of weathering and therefore on the amount of smectite and mixed layer (illite-smectite) clays present in the saprolite. The chargeability of the core samples was in the range of and is strongly dependent on the salinity. We also performed streaming potential measurements with the same pore fluid composition as that used for the complex conductivity measurements. We found an excess of movable electrical charges on the order of 100 to in agreement with previous investigations connecting the movable excess charge density to permeability. The zeta potential was in the range of to independent on the salinity. The electrical measurements were consistent with an average cation exchange capacity in the range of 1.4 to and a specific surface area on the order of 4000 to about 30,000 . Read More: http://library.seg.org/doi/abs/10.1190/geo2012-0176.1

Revil, André↗

Tree Ring Chronology Indexes and Reconstructions of Precipitation in Central Iowa, USA (1984) (NDP-002)

Tree core samples (4 mm in diameter) were extracted from the trunks of white oak (Quercus alba) at three sites in central Iowa (Duvick Back Woods, Ledges State Park, and Pammel). At least 60 trees were sampled at each site, and at least two cores were taken from each tree. The growth rings of each core were dated by calendar year and measured; the measurements were then transformed into dimensionless ring-width indices and correlated with annual precipitation. Data were collected for the years 1680 through 1979. Each tree ring was characterized by the site, year, tree-ring-width index, number of core samples, decade year, and the annual reconstructed precipitation estimate. These data have more than 50% of their variance in common with the known annual statewide average precipitation for Iowa and serve as useful indicators of the precipitation and drought history of the region for the past 300 years. The data are in two files: tree-ring-chronology data (8 kB) and the annual reconstructed precipitation data for central Iowa (2 kB).For access to the data files, click this link to the CDIAC data transition website: http://cdiac.ess-dive.lbl.gov/ndps/ndp002.html

54 ENVIRONMENTAL SCIENCES↗

Stress-sensitivity of fracture conductivity of Tuscaloosa Marine Shale cores

Production decline from wells producing from shale rocks is typically quite rapid. One possible factor responsible for such decline is loss in fracture conductivity. This is true in the case of the Tuscaloosa Marine shale reservoir. In this work, the stress-dependent fracture conductivity of TMS core samples is investigated using five propped cores under varying stress conditions. In addition, the effects of static rock mechanical properties and rock mineralogy on conductivity decline are investigated. The mineralogy of each core sample was determined by X-ray Diffraction analysis. Fracture conductivity was measured using a Hassler-type pressure core holder with a pressure rating of 15,000 psi (103.42 MPa). Estimated rock mechanical properties showed that shale anisotropy could affect fracture conductivity. The time decline in conductivity revealed two possible decline trends, a) decline from the reduction in induced fracture width, and b) decline from the healing of developed micro-cracks. An exponential decline in fracture conductivity with increasing confinement pressure was observed with an average decline rate constant of 3.15 x 10 -10 mPa -1 . While rock mineralogy did not have any clear relationship with conductivity decline, the effects of rock mechanical properties were only important at 10.34 MPa confinement pressure and above. The observation showed that a high Young's modulus correlate to high conductivity, whereas a high Poisson's ratio correlate to low conductivity. This study provides useful observations for optimizing fracture design to enhance well productivity in the TMS.

02 PETROLEUM↗

Alteration of volcanic rocks: A new non-intrusive indicator based on induced polarization measurements

Induced polarization is a geophysical method investigating the ability of rocks to store reversibly electrical charges under a slowly alternating electrical field. The material property of interest is a complex-valued electrical conductivity with an in-phase component associated with conduction and a quadrature component associated with polarization. Here we investigated the relationship between complex conductivity spectra over the frequency range 1 mHz–45 kHz and the specific surface area (SSA) of 28 volcanic core samples extracted from a wellbore drilled for the Humu'ula Groundwater Research Project in Hawaii. The specific surface area of these samples was determined through the Brunauer, Emmett and Teller (BET) method. Subcritical nitrogen adsorption experiments were conducted using two different instruments and the samples were prepared in both pellets and powder forms. The BET specific surface area is found to be highly correlated to the cation exchange capacity of the core samples measured by the cobalthexamine method. The in-phase conductivity itself can be decomposed as the sum of a bulk contribution associated with conduction in the bulk pore water and a surface conductivity associated with conduction in the electrical double layer coating the grains. The surface conductivity, the quadrature conductivity, and the normalized chargeability (defined as the difference between the in-phase conductivity at high and low frequencies) are observed to be linearly correlated to the specific surface area or the surface per volume ratio of the core samples, which can be considered as proxy of alteration. These trends are consistent with those shown by sedimentary rocks. This new data set demonstrates that the induced polarization method can be potentially used to image alteration in volcanic environments.

58 GEOSCIENCES↗

A rock physics and seismic reservoir characterization study of the Rock Springs Uplift, a carbon dioxide sequestration site in Southwestern Wyoming

We present a reservoir geophysics study, including rock physics modeling and seismic inversion, of a carbon dioxide sequestration site in Southwestern Wyoming, namely the Rock Springs Uplift, and build a petrophysical model for the potential injection reservoirs for carbon dioxide sequestration. Our objectives include the facies classification and the estimation of the spatial model of porosity and permeability for two sequestration targets of interest, the Madison Limestone and the Weber Sandstone. The available dataset includes a complete set of well logs at the location of the borehole available in the area, a set of 110 core samples, and a seismic survey acquired in the area around the well. The proposed study includes a formation evaluation analysis and facies classification at the well location, the calibration of a rock physics model to link petrophysical properties and elastic attributes using well log data and core samples, the elastic inversion of the pre-stack seismic data, and the estimation of the reservoir model of facies, porosity and permeability conditioned by seismic inverted elastic attributes and well log data. In particular, the rock physics relations are facies-dependent and include granular media equations for clean and shaley sandstone, and inclusion models for the dolomitized limestone. The permeability model has been computed by applying a facies-dependent porosity-permeability relation calibrated using core sample measurements. Finally, the study shows that both formations show good storage capabilities. The Madison Limestone includes a homogeneous layer of high-porosity high-permeability dolomite; the Weber Sandstone is characterized by a lower average porosity but the layer is thicker than the Madison Limestone.

58 GEOSCIENCES↗

Development of a Neutron Diffraction Based Experiemental Capability for Investigating Hydraulic Fracturing for EGS-like Conditions

Hydraulic fracturing to enhance formation permeability is an established practice in the Oil & Gas (O&G) industry and is expected to be an enabler for EGS. However, it is rarely employed in conventional geothermal systems and there are significant questions regarding the translation of practice from O&G to both conventional geothermal and EGS applications. Lithological differences(sedimentary versus crystalline rocks, significantly greater formation temperatures and different desired fracture characteristics are among a number of factors that are likely to result in a gap of understanding of how to manage hydraulic fracturing practice for geothermal. Whereas the O&G community has had both the capital and the opportunity to develop its understanding of hydraulic fracturing operations empirically in the field as well through extensive R&D efforts, field testing opportunities for EGS are likely to be minimal due to the high expense of hydraulic fracturing field trials. A significant portion of the knowledge needed to guide the management of geothermal/EGS hydraulic fracturing operations will therefore likely have to come from experimental efforts and simulation. This paper describes ongoing efforts at Oak Ridge National Laboratory (ORNL) to develop an experimental capability to map the internal stresses/strains in core samples subjected to triaxial stress states and temperatures representative of EGS-like conditions using neutron diffraction based strain mapping techniques. This capability is being developed at ORNL\'s Spallation Neutron Source, the world\'s most powerful pulsed neutron source and is still in a proof of concept phase. A specialized pressure cell has been developed that permits independent radial and axial fluid pressurization of core samples, with axial flow through capability and a temperature rating up to 300 degrees C. This cell will ultimately be used to hydraulically pressurize EGS-representative core samples to conditions of imminent fracture and map the associated internal strain states of the sample. This will hopefully enable a more precise mapping of the rock material failure envelope, facilitate a more refined understanding of the mechanism of hydraulically induced rock fracture, particularly in crystalline rocks, and serve as a platform for validating and improving fracture simulation codes. The elements of the research program and preliminary strain mapping results of a Sierra White granite sample subjected only to compressive loading will be discussed in this paper.

egs↗

Radiochemical tracers as a mix diagnostic for the ignition double-shell capsule

One of the most important challenges confronting laser-driven capsule implosion experiments will be a quantitative evaluation of the implosion dynamics. Since these experiments will encounter extreme conditions of pressure and temperature, establishing robust, sensitive diagnostics will be difficult. Radiochemical signatures provide insight into material mixing and laser drive asymmetry and complement x-ray and other nuclear diagnostics, since the relevant nuclear reactions sample core implosion conditions directly. Simulations of an ignition double shell target indicate that several experimentally accessible isomeric ratios will be suitable monitors of mix.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Experimental study of compaction localization in carbonate rock and constitutive modeling of mechanical anisotropy

Abstract Sedimentary rocks are inherently anisotropic and prone to strain localization. While the influence of rock anisotropy on the brittle/dilative regime has been studied extensively, its influence on the ductile/compactive regime is much less explored. This paper discusses the anisotropic behavior of a high‐porosity carbonate rock from central Europe (the Maastricht Tuffeau). A set of triaxial tests with concurrent x‐ray tomography has been performed at different confining pressures. The anisotropic characteristics of this rock have been investigated by testing samples cored at different inclinations of the bedding, thus revealing non‐negligible effects of the coring direction on yielding and compaction behavior. Specifically, samples cored perpendicular to bedding display higher strength and longer stages of post‐yielding deformation before manifesting re‐hardening. Despite such alterations of the inelastic response, Digital Image Correlation has revealed that the strain localization mode is independent of the coring direction, thus being primarily affected by the confinement level. To capture the observed interaction between material anisotropy and compaction behavior at the continuum‐scale, an elastoplastic constitutive law has been proposed. For this purpose, a set of tensorial bases has been introduced to replicate how the oriented rock fabric modulates the yielding and plastic flow characteristics of the material. The analyses show that the impact of the coring direction on yield function and plastic flow rule is fundamentally different, thus requiring the use of distinct projection strategies (a strategy here defined heterotopic mapping). The performance of the model, studied through parametric analyses and by calibrating the experimental results, illustrates the improved capability of the proposed constitutive approach when applied to strongly anisotropic porous rocks.

Shahin, Ghassan↗

Snake River Plain FORGE: Well Data for USGS-142

Well data for the USGS-142 well located in eastern Snake River Plain, Idaho. This data collection includes lithology reports, borehole logs, and photos of rhyolite core samples. This collection of data has been assembled as part of the site characterization data used to develop the conceptual geologic model for the Snake River Plain site in Idaho, as part of phase 1 of the Frontier Observatory for Research in Geothermal Energy (FORGE) initiative. They were assembled by the Snake River Geothermal Consortium (SRGC), a team of collaborators that includes members from national laboratories, universities, industry, and federal agencies, lead by the Idaho National Laboratory (INL).

15 GEOTHERMAL ENERGY↗

Predicting uniaxial compressive strength from empirical relationships between ultrasonic p-wave velocities, porosity, and core measurements in a potential geothermal reservoir, Snake River Plain, Idaho

Empirical, core-based, predictive correlations for the calculation of uniaxial compressive strength (UCS) were developed from compressive sonic velocity measurements (55 whole core samples) and porosity, density, and unconfined compressive tests (110 whole core samples). The samples were collected at 55 different depths in a 550 m (1800 ft) interval of core from the MH-2 borehole located in southern Idaho, USA. The western Snake River Plain is a known region of high heat flow and the borehole was drilled into a potential geothermal reservoir characterized by artesian flow of high-temperature (~140°C) fluids from fractured basalt. UCS was measured in unconfined compressive tests, density and porosity were measured using a He-pycnometer, and p-wave velocities were measured in a pressure vessel under variable confining pressures. We use correlations between density and p-wave velocity (R 2 = 0.91), UCS and porosity (R 2 = 0.78), and UCS and p-wave velocity (R 2 = 0.79) in a method to calculate calibrated UCS from wireline logs. Here, the impact of this predictive correlation is that UCS can be calculated from as little as a bulk density log when sonic logs and core are not available, greatly increasing the number of wells in which we can obtain a local UCS estimate.

15 GEOTHERMAL ENERGY↗

SPRUCE Peat Mercury, Methylmercury and Sulfur Concentrations from Experimental Plot Cores, Beginning in 2014

This data set reports the results of physical and chemical analyses of peat core samples from the SPRUCE experimental study plots located in the S1-Bog in northern Minnesota, 40 km north of Grand Rapids in the USDA Forest Service Marcell Experimental Forest (MEF). Sample collection and analyses started in June of 2014 and will continue for the duration of the experiment. Core samples are collected annually from all 12 plots to a depth of 200cm in 10cm and 25cm increments. Samples are analyzed for total mercury concentration, methylmercury concentration, percent carbon, percent nitrogen, and percent sulfur.

54 ENVIRONMENTAL SCIENCES↗

CO 2 -brine relative permeability and capillary pressure of Tuscaloosa sandstone: Effect of anisotropy

Relative permeability and capillary pressure are known as essential properties that have substantial impacts on the accuracy of reservoir simulations. The effect of small-scale heterogeneity and lamination in the rock structure is often ignored during the measurement of capillary pressure and relative permeability curves in core samples. This study highlights the remarkable impact of anisotropy on the multiphase flow properties of stratified formations. A series of steady-state CO 2 -brine drainage and imbibition tests are conducted at reservoir conditions in horizontal and vertical core samples of the Tuscaloosa sandstone from the Cranfield CO 2 injection site in Mississippi. The relative permeability curves represent an anisotropic behavior influenced by the heterogeneous and laminated structure of realistic rock samples. The CO 2 saturation profiles during drainage and imbibition cycles indicate that the phase distribution in the pore space is controlled by core-scale heterogeneity in the porosity distribution among the laminations that causes capillary pressure inhomogeneity. Using the saturation profile during the imbibition cycle, the trapping characteristic of the horizontal and vertical rock samples are compared and we found that the capillary trapping is less likely in the vertical direction. Furthermore, the centrifuge-measured capillary pressure demonstrates distinctive characteristics for horizontal and vertical core samples. Since the flooding experiments are performed under capillary controlled flow, the capillary pressure contrast in the laminated structure of the rock strongly affects the relative permeability. The presented results can potentially improve the accuracy of the large-scale simulations for the CO 2 post-injection period, in which the vertical displacement has an important role in the plume migration.

58 GEOSCIENCES↗

Physical and Hydraulic Properties of RCRA Borehole Samples from the Hanford Site : Final Report, Fiscal Years 2023-2024

Sediment from 44 core samples collected from Resource Conservation and Recovery Act (RCRA) boreholes drilled in the 200 East and 200 West areas of the Hanford Site were characterized for physical and hydraulic properties (Table S.1). Characterization data included gravimetric water contents and matric potentials, grain-size distributions, saturated hydraulic conductivity, water retention characteristics, and unsaturated hydraulic conductivity. These properties provide site-specific data and parameters that can be used in subsurface flow and contaminant transport models to assess the transport and fate of contaminants in the vadose zone and underlying aquifer systems. The analyzed core samples come from specific areas and depth intervals at the Hanford Site that were targeted for sampling to address data gaps identified by site contractors (Khaleel 2020). X-ray computed tomography (XCT) was used to evaluate the general textural characteristics of the samples and to determine which samples to use for further physical and hydraulic property characterization. Subsequent sample selection was determined by consensus after review of the XCT images by Pacific Northwest National Laboratory, Central Plateau Cleanup Company, and INTERA staff.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗