Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “control layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Analytical study of blowing boundary layer control for subsonic V/STOL inlets

The analytical methods used to study blowing boundary-layer control (BLC) for subsonic V/STOL inlets at the NASA Lewis Research Center are briefly described. The methods are then shown to give good agreement with experimental results, both with and without blowing BLC. Finally, because of this good agreement, the methods have been used to determine analytically the optimum (minimum blowing power required) location and height for a blowing slot within a subsonic V/STOL inlet. Results of this analytical study are presented.

Hwang, D. P.↗
NASA NTRS1947

Effect of Various Methods of Boundary-Layer Control on Performance of V-1710-93 Engine-Stage Supercharger

Four methods of boundary-layer control were tried during an investigation to improve the flow in the impeller passages of a V-1710-93 engine-stage supercharger. The boundary layer along the impeller front shroud was removed by suction. In one method the removal was accomplished by recirculation of the air to the impeller inlet; in another method, by external removal. In the other methods, slots were cut through the impeller-blade faces first at 30 percent and then at 30 and 70 percent of the mean-flow-path length measured from leading edges of the rotating inlet guide vanes to introduce air from the high-pressure side of the blades into the region where stagnation and separation were suspected. A slight improvement in performance was obtained when the boundary layer was removed through the impeller front shroud. In general, this improvement become more pronounced as the amount of air removed was increased even though the excessive impeller frontal clearance maintained for these tests, together with an exaggerated negative pressure gradient, apparently induced flow separation on the diffuser front and rear walls as well as on the impeller front shroud. The use of slots in the impellers at the locations selected had a detrimental effect on the supercharger performance characteristics.

Kohl, Robert C.↗
NASA NTRS1984

Analytical study of suction boundary layer control for subsonic V/STOL inlets

Analytical procedures used to evaluate the application of suction boundary-layer control (BLC) to subsonic V/STOL inlets are presented. These procedures have been used to analytically predict the optimum (minimum suction power required) location and extent for a suction slot of two different surface resistances within a subsonic V/STOL inlet. Results of this analytical study are presented.

Boles, M. A.↗
NASA NTRS1947

Calculations and Experimental Investigations on the Feed-Power Requirement of Airplanes with Boundary-Layer Control

Calculations and test results are given about the feed-power requirement of airplanes with boundary-layer control. Curves and formulas for the rough estimate of pressure-loss and feed-power requirement are set up for the investigated arrangements which differ structurally and aerodynamically. According to these results the feed power for three different designs is calculated at the end of the report.

Krueger, W.↗
NASA NTRS1960

Full-Scale Wind-Tunnel Tests of Blowing Boundary-Layer Control Applied to a Helicopter Rotor

A full-scale wind-tunnel test was conducted of two boundary-layer-control applications to a 44-foot diameter helicopter rotor. Blowing from a nozzle near the leading edge of the blades delayed retreating blade stall. Results also indicated that delay of retreating blade stall could be obtained by cyclic blowing with a lower flow rate than that required for continuous blowing. It was found that blowing applied through a nozzle at mid-chord had no effect on retreating blade stall.

McCloud, John L., III↗
NASA NTRS1999

Subsonic Investigation of a Leading-Edge Boundary Layer Control Suction System on a High-Speed Civil Transport Configuration

A wind tunnel investigation of a leading edge boundary layer control system was conducted on a High Speed Civil Transport (HSCT) configuration in the Langley 14- by 22-Foot Subsonic Tunnel. Data were obtained over a Mach number range of 0.08 to 0.27, with corresponding chord Reynolds numbers of 1.79 x 10(exp 6) to 5.76 x 10(exp 6). Variations in the amount of suction, as well as the size and location of the suction area, were tested with outboard leading edge flaps deflected 0 and 30 deg and trailing-edge flaps deflected 0 and 20 deg. The longitudinal and lateral aerodynamic data are presented without analysis. A complete tabulated data listing is also presented herein.

Campbell, Bryan A.↗
NASA NTRS1974

The design and performance of axially symmetrical contoured wall diffusers employing suction boundary layer control

This paper presents a procedure for the design and the performance prediction of axially symmetrical contoured wall diffusers employing suction boundary layer control. An inverse problem approach was used in the potential flow design of the diffuser wall contours. The experimentally observed flow characteristics and the stability of flows within the diffuser are also described. Guidelines for the design of low suction (less than 10 percent of the inlet flow) and thus high effectiveness contoured wall diffusers are also provided based on the results of the experimental program.

Nelson, C. D., Jr.↗
NASA NTRS1960

An Experimental Investigation of Boundary-Layer Control for Drag Reduction of a Swept-Wing Section at Low Speed and High Reynolds Numbers

An investigation of laminar boundary-layer control by suction for purposes of drag reduction at low speed and high Reynolds numbers has been conducted in the Ames 12-Foot Pressure Wind Tunnel. The model was a 72.96-inch-chord wing panel, swept back 30 deg., which was installed between end plates to approximate a wing of infinite span. The airfoil section employed was a modified NACA 66-012 in the streamwise direction. Tests were limited to controlling the flow over only the upper surface of the model. Seventeen individually controllable suction chambers were provided below the surface to induce flow through 93 spanwise slots in the surface between the 0.0052- and 0.97-chord stations. Tests were made at angles of attack of 0 deg., +/- 1.0 deg., +/- 1.5 deg., and -2.0 deg. for Reynolds numbers from approximately 1.5 x 10(exp 6) to 4.0 x 10(exp 6) per foot. In general, essentially full-chord laminar flow was obtained for all conditions with small suction quantities. Minimum profile-drag coefficients of about 0.0005 to 0.0006 were obtained for the slotted surface at maximum values of the Reynolds number; these values include the Power required to induce suction as an equivalent drag.

Gault, Donald E.↗
NASA NTRS1985

Supercritical airfoil drag reduction by passive shock wave/boundary layer control in the Mach number range .75 to .90

Airfoils operating in the transonic region are subject to large increases in drag due to shock wave/boundary layer interactions. The concept of passive shock wave/boundary layer control seeks drag reduction by placing a thin cavity with a porous top surface at the airfoil chordwise position where a shock wave would normally occur. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and reduce entropy increases through the shock wave. In this investigation this concept is studied at a freestream Mach number range of .75 and .90. The Mach number distributions over the model, the wake impact pressure surveys used to determine profile drag and schlieren photographs for 2.8 percent porosity and solid airfoil cases are presented and compared. Results indicate that the profile drag coefficient can be reduced by as much as 40 percent through the use of this passive drag control system.

Nagamatsu, H. T.↗
NASA NTRS1960

Flight Investigation of the Low-Speed Characteristics of a 45 deg Swept-Wing Fighter-Type Airplane with Blowing Boundary-Layer Control Applied to the Leading- and Trailing-Edge Flaps

A flight investigation has been conducted to study how pilots use the high lift available with blowing-type boundary-layer control applied to the leading- and trailing-edge flaps of a 45 deg. swept-wing airplane. The study includes documentation of the low-speed handling qualities as well as the pilots' evaluations of the landing-approach characteristics. All the pilots who flew the airplane considered it more comfortable to fly at low speeds than any other F-100 configuration they had flown. The major improvements noted were the reduced stall speed, the improved longitudinal stability at high lift, and the reduction in low-speed buffet. The study has shown the minimum comfortable landing-approach speeds are between 120.5 and 126.5 knots compared to 134 for the airplane with a slatted leading edge and the same trailing-edge flap. The limiting factors in the pilots' choices of landing-approach speeds were the limits of ability to control flight-path angle, lack of visibility, trim change with thrust, low static directional stability, and sluggish longitudinal control. Several of these factors were found to be associated with the high angles of attack, between 13 deg. and 15 deg., required for the low approach speeds. The angle of attack for maximum lift coefficient was 28 deg.

Quigley, Hervey C.↗
NASA NTRS1959

Full-Scale Wind-Tunnel Investigation of a Jet Flap in Conjunction with a Plain Flap with Blowing Boundary-Layer Control on a 35 deg Sweptback-Wing Airplane

Previous investigations have shown that increased blowing at the hinge-line radius of a plain flap will give flap lift increases above that realized with boundary-layer control. Other experiments and theory have shown that blowing from a wing trailing edge, through the jet flap effect, produced lift increases. The present investigation was made to determine whether blowing simultaneously at the hinge-line radius and trailing edge would be more effective than blowing separately at either location. The tests were made at a Reynolds number of 4.5 x 10(exp 6) with a 35 deg sweptback-wing airplane. For this report, only the lift data are presented. Of the three flap blowing arrangements tested, blowing distributed between the trailing edge and the hinge-line radius of a plain flap was found to be superior to blowing at either location separately at the plain flap deflections of interest. Comparison of estimated and experimental jet flap effectiveness was fair.

Aoyagi, Kiyoshi↗
DOE OSTI2022

Current state and future trends in boundary layer control on lifting surfaces

Successful flow control may bring numerous benefits, such as flow stabilization, flow reattachment, separation delay, drag reduction, lift increase, aerodynamic performance improvement, energy efficiency increase, shock delay or weakening, noise reduction, etc. For these purposes, many different flow control devices, which can be classified as passive, semi-active and active, have been designed and tested. This review paper aims to highlight the most promising and commonly employed boundary layer control methods as well as outline their potential in specific applications in aerospace and energy engineering. Referenced studies, performed on various geometries (flat plates, channels, airfoils, wings, blades, cylinders), are primarily numerical or experimental. Although enhanced aerodynamic performance is achieved in many cases, further research is required to draw general conclusions. This paper aims to demonstrate that, in the future, we may expect further developments of flow control actuators, as well as their increased application.

42 ENGINEERING↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1961

Investigation of Longitudinal and Lateral Stability Characteristics of a Six-Propeller Deflected-Slipstream VTOL Model with Boundary-Layer Control Including Effects of Ground Proximity

An investigation of the longitudinal and lateral stability and control and Performance characteristics of a six-propeller deflected- slipstream vertical-take-off-and-landing (VTOL) model in the transition speed range was conducted in the 17-foot test section of the Langley 300-MPH 7- by 10-foot tunnel. A complete analysis of the data was not conducted. A modest amount of blowing boundary-layer control was necessary to achieve transition without wing stall.

Grunwald, Kalman J.↗
DOE OSTI2023

Boundary Layer Controls on the Shallow-to-Deep Cumulus Transition (Final Technical Report)

This project advanced our understanding of the processes governing cumulus cloud formation and provides an improved observational basis for validating earth system models. To be specific, the project used laser- and radar-remote sensors to examine the physical properties of updrafts that rise from earth’s surface and initiate clouds deeper in the atmosphere. These updrafts comprise “thermals” and “plumes” and occur at small spatial and temporal scales (e.g., 10s of minutes, 100s of meters). These small scales preclude explicit representation in most earth system and climate models, and thus necessitate “sub-grid-scale” parameterization of updraft processes. The innovation of this project was to directly measure the size, shape, strength and water vapor content of these updrafts with Doppler and Raman lidars, respectively, and to link these updraft properties to cloud processes using vertically pointed weather radars. The resulting data sets comprise 100s of thousands of updrafts and thousands of clouds, which far exceeds previous efforts, and thereby provides a robust statistical and physical representation of these processes. From these large datasets the project produced a sequence of scientific analyses that: (1) Elucidate how variations in the turbulent structure of the convective boundary layer control shallow cumulus convection, (2) Quantify the upward transport of water vapor to cloud base via thermals and plumes, (3) Validate large-eddy simulations of updrafts and shallow convective clouds, (4) Demonstrate a size-to-strength relationship between updraft width and updraft speed, and (5) Demonstrate how updrafts interact with the stability at the top of the convective boundary layer to modulate the depth and vigor of convective clouds. These results have been disseminated via several published journal articles, academic theses, and conference presentations. Collectively these results contribute to the Atmospheric System Research (ASR) program’s goal to “improve understanding of the key cloud, aerosol, precipitation, and radiation processes that affect the Earth’s radiative balance and hydrological cycle, particularly processes that limit the predictive ability of regional and global earth system models”.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Passive shock wave/boundary layer control for transonic airfoil drag reduction

An investigation of the passive shock wave/boundary layer interaction control for reducing the drag in 12 percent thick circular arc and 14 percent thick supercritical airfoils was conducted in a 3 in. x 15.4 in. transonic wind tunnel at transonic Mach numbers. A porous surface with a cavity beneath it was positioned on the area of the airfoils, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure data for determining the profile drag, and the Schlieren photographs for porous surface airfoils are presented and compared with the results for solid surface airfoils. With the porous surface the normal shock wave for solid surface was changed to a lambda shock wave system, and the wake impact pressure data indicated an appreciable drag reduction for both airfoils with the porous surface at transonic speeds while causing little or no loss of lift. The effect of porosity and cavity size is investigated and off-design performance is discussed.

Bahi, L.↗