Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cleaning performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Independent Effects of Reynolds Number and Mach Number on the Aerodynamics of an Iced Swept Wing

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional (3D) icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind tunnel testing was carried out for a 13.3-percent-scale semispan wing based upon the Common Research Model airplane configuration. The wind tunnel testing was conducted at the Office National d’Etudes et de Recherches Aérospatiales (ONERA) F1 pressurized wind tunnel with Reynolds numbers of 1.6 x 10(exp 6) to 11.9 x 10(exp 6 ) and Mach numbers of 0.09 to 0.34. Five different configurations were investigated using fully 3D, high-fidelity artificial ice shapes that maintain nearly all of the 3D ice-accretion features documented in prior icing wind tunnel tests. These large, leading-edge ice shapes were nominally based upon airplane holding in icing conditions scenarios. For three of these configurations, lower fidelity simulations were also built and tested. The results presented in this paper show that while Reynolds and Mach number effects are important for quantifying the clean-wing performance, there is very little to no effect for an iced wing with 3D, high-fidelity artificial ice shapes or 3D smooth ice shapes with grit roughness. These conclusions are consistent with the large volume of past research on iced airfoils. However, some differences were also noted for the associated stalling angle of the iced swept wing and for various lower fidelity versions of the leading-edge ice accretion. More research is planned to further investigate the key features of ice-accretion geometry that must be simulated in lower fidelity versions in order to capture the essential aerodynamics.

Aircraft icing↗
NASA NTRS1977

Quiet Clean Short-haul Experimental Engine (QCSEE). Aerodynamic and aeromechanical performance of a 50.8 cm (20 inch) diameter 1.34 PR variable pitch fan with core flow

The fan aerodynamic and aeromechanical performance tests of the quiet clean short haul experimental engine under the wing fan and inlet with a simulated core flow are described. Overall forward mode fan performance is presented at each rotor pitch angle setting with conventional flow pressure ratio efficiency fan maps, distinguishing the performance characteristics of the fan bypass and fan core regions. Effects of off design bypass ratio, hybrid inlet geometry, and tip radial inlet distortion on fan performance are determined. The nonaxisymmetric bypass OGV and pylon configuration is assessed relative to both total pressure loss and induced circumferential flow distortion. Reverse mode performance, obtained by resetting the rotor blades through both the stall pitch and flat pitch directions, is discussed in terms of the conventional flow pressure ratio relationship and its implications upon achievable reverse thrust. Core performance in reverse mode operation is presented in terms of overall recovery levels and radial profiles existing at the simulated core inlet plane. Observations of the starting phenomena associated with the initiation of stable rotor flow during acceleration in the reverse mode are briefly discussed. Aeromechanical response characteristics of the fan blades are presented as a separate appendix, along with a description of the vehicle instrumentation and method of data reduction.

Giffin, R. G.↗
NASA NTRS1995

Effects of bearing cleaning and lube environment on bearing performance

Running torque data of SR6 ball bearings are presented for different temperatures and speeds. The data are discussed in contrast to generally used torque prediction models and point out the need to obtain empirical data in critical applications. Also, the effects of changing bearing washing techniques from old, universally used CFC-based systems to CFC-free aqueous/alkaline solutions are discussed. Data on wettability, torque and lubricant life using SR3 ball bearings are presented. In general, performance is improved using the new aqueous washing techniques.

Ward, Peter C.↗
NASA NTRS1983

Development of a clean optical telescope

Particulate contamination on astronomical mirrors degrades performance in two ways: by information loss by extinction of light; and background and noise from scattering, especially forward or Fraunhofer scattering. These effects were not generally understood, and an ambitious pilot program was outlined to measure particulate effects on telescope optical performance; develop prophylactic and cleaning procedures suitable for groundbased observatories; investigate by computational modelling the effects on telescopes in space; and communicate the results and concerns within the astronomical community.

Brown, R. A.↗
NASA NTRS2005

Experimental Investigation of Ice Accretion Effects on a Swept Wing

An experimental investigation was conducted to study the effects of 2-, 5-, 10-, and 22.5-min ice accretions on the aerodynamic performance of a swept finite wing. The ice shapes tested included castings of ice accretions obtained from icing tests at the NASA Glenn Icing Research Tunnel (IRT) and simulated ice shapes obtained with the LEWICE 2.0 ice accretion code. The conditions used for the icing tests were selected to provide five glaze ice shapes with complete and incomplete scallop features and a small rime ice shape. The LEWICE ice shapes were defined for the same conditions as those used in the icing tests. All aerodynamic performance tests were conducted in the 7- x 10-ft Low-Speed Wind Tunnel Facility at Wichita State University. Six component force and moment measurements, aileron hinge moments, and surface pressures were obtained for a Reynolds number of 1.8 million based on mean aerodynamic chord and aileron deflections in the range of -15o to 20o. Tests were performed with the clean wing, six IRT ice shape castings, seven smooth LEWICE ice shapes, and seven rough LEWICE ice shapes. Roughness for the LEWICE ice shapes was simulated with 36-size grit. The experiments conducted showed that the glaze ice castings reduced the maximum lift coefficient of the clean wing by 11.5% to 93.6%, while the 5-min rime ice casting increased maximum lift by 3.4%. Minimum iced wing drag was 133% to 3533% greater with respect to the clean case. The drag of the iced wing near the clean wing stall angle of attack was 17% to 104% higher than that of the clean case. In general, the aileron remained effective in changing the lift of the clean and iced wings for all angles of attack and aileron deflections tested. Aileron hinge moments for the iced wing cases remained within the maximum and minimum limits defined by the clean wing hinge moments. Tests conducted with the LEWICE ice shapes showed that in general the trends in aerodynamic performance degradation of the wing with the simulated ice shapes were similar to those obtained with the IRT ice shape castings. However, in most cases, the ice castings resulted in greater aerodynamic performance losses than those obtained with the LEWICE ice shapes. For the majority of the LEWICE ice shapes, the addition of 36-size grit roughness to the smooth ice shapes increased aerodynamic performance losses.

Ice shape↗
NASA NTRS2022

Dusty Environment Classification and Testing: Dust Mitigation Slide Wipes & Tapes

During the Apollo missions many mechanisms, equipment, and surfaces were contaminated by lunar dust and often negatively affected. The methods used to clear these devices of dust proved ineffective, which led to premature failure in some cases. Systems being designed for upcoming missions to the Moon will need to address the performance degradation risk of dust contamination. Surfaces at risk include thermal control surfaces, solar cells, camera and sensor optics, seals, metal joints and tools, and space suit assemblies. To improve state of the art dust mitigation approaches, the dust mitigation team at NASA Glenn Research Center (GRC) explored the effects imposed on substrates during cleaning activities in the presence of lunar dust. The Uniform Dust Deposition System (UDDS) was used to conduct a study of various cleaning techniques on different substrates. Test substrates and cleaning media were selected to represent a wide range of structural and functional materials. Substrates included orthofabric, thermal radiator coating, aluminum, quartz glass, silicone rubber, aluminized Mylar, and FEP. Cleaning materials included cloth wipes, tapes, a brush, and a pliable cleaner concept. Cleaning material / substrate pairs were rated on cleaning efficiency, substrate damage, cleaning material longevity, and ease of use. The best performing cleaning method varied based on application.

lunar simulant↗
NASA NTRS1975

Performance of a J85-13 compressor with clean and distorted inlet flow

The results presented are of a series of experimental tests in which a J85-13 turbojet engine was subjected to both distorted and undistorted inlet total pressure conditions. A distinctive feature of the data base obtained is that it includes compressor interstage information not previously recorded for a J85-13 engine. Each of the eight compressor stages was instrumented to obtain the characteristics of the individual stages for undistorted inlet conditions, and these data are documented in the report along with the undistorted compressor overall performance. Also included in the report is the overall performance of the compressor exposed to 14 different distorted-inlet conditions - 10 circumferential patterns and 4 radial patterns. The distortion patterns were introduced using screens that spoiled from 8 to 50 percent of the compressor face area; the distortion screen density, or the area blocked by the screen wire per unit area of screen, varied from 26 to 69 percent.

Milner, E. J.↗
NASA NTRS1996

Supersonic Gas-Liquid Cleaning System

The Supersonic Gas-Liquid Cleaning System Research Project consisted mainly of a feasibility study, including theoretical and engineering analysis, of a proof-of-concept prototype of this particular cleaning system developed by NASA-KSC. The cleaning system utilizes gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the device to be cleaned. The cleaning fluid being accelerated to these high velocities may consist of any solvent or liquid, including water. Compressed air or any inert gas is used to provide the conveying medium for the liquid, as well as substantially reduce the total amount of liquid needed to perform adequate surface cleaning and cleanliness verification. This type of aqueous cleaning system is considered to be an excellent way of conducting cleaning and cleanliness verification operations as replacements for the use of CFC 113 which must be discontinued by 1995. To utilize this particular cleaning system in various cleaning applications for both the Space Program and the commercial market, it is essential that the cleaning system, especially the supersonic nozzle, be characterized for such applications. This characterization consisted of performing theoretical and engineering analysis, identifying desirable modifications/extensions to the basic concept, evaluating effects of variations in operating parameters, and optimizing hardware design for specific applications.

Kinney, Frank↗
NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗
NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗
NASA NTRS1997

Adhesion Performance of Solid Film Lubricants on Substrates Cleaned With Environmentally Compliant Cleaners

Solid film adhesion testing was used to determine the effect different environmentally compliant cleaners have on the adhesion properties of solid film lubricants used for several NASA programs. In an action to remove ozone depleting chemicals from aerospace processes, a replacement cleaner must be identified that does not affect the adhesion of solid film lubricants used on flight critical NASA hardware. ASTM D251083 Standard Test Method for Adhesion of Solid Film Lubricants was used to evaluate the cleaners. Two different lubricants - Inlox 88 and Boosterlube - were tested using various commercially available cleaners. Inlox 88 is produced by E/M Corporation and is a liquid oxygen compatible lubricant used in the Space Shuttle Main Engine, and Boosterlube is a new lubricant being implemented for use on the Space Shuttle Solid Rocket Booster. These lubricants were selected because of their specific use on flight critical NASA components. Results of this testing are presented in the paper.

Hall, P. B.↗
NASA NTRS2000

Spacecraft Communications System Verification Using On-Axis Near Field Measurement Techniques

Determination of the readiness of a spacecraft for launch is a critical requirement. The final assembly of all subsystems must be verified. Testing of a communications system can mostly be done using closed-circuits (cabling to/from test ports), but the final connections to the antenna require radiation tests. The Tropical Rainfall Measuring Mission (TRMM) Project used a readily available 'near-fleld on-axis' equation to predict the values to be used for comparison with those obtained in a test program. Tests were performed in a 'clean room' environment at both Goddard Space Flight Center (GSFC) and in Japan at the Tanegashima Space Center (TnSC) launch facilities. Most of the measured values agreed with the predicted values to within 0.5 dB. This demonstrates that sometimes you can use relatively simple techniques to make antenna performance measurements when use of the 'far field ranges, anechoic chambers, or precision near-field ranges' are neither available nor practical. Test data and photographs are provided.

Keating, Thomas↗
NASA NTRS1921

Effects of nature of cooling surface on radiator performance

This report discusses the effects of roughness, smoothness, and cleanness of cooling surfaces on the performance of aeronautic radiators, as shown by experimental work, with different conditions of surface, on (1) heat transfer from a single brass tube and from a radiator; (2) pressure drop in an air stream in a single brass tube and in a radiator; (3) head resistance of a radiator; and (4) flow of air through a radiator. It is shown that while smooth surfaces are better than rough, the surfaces usually found in commercial radiators do not differ enough to show marked effect on performance, provided the surfaces are kept clean.

Parsons, S R↗
NASA NTRS2018

James Webb Space Telescope Primary and Secondary Mirror Segment Assemblies Cleaning: a Quantitative Assessment

The James Webb Space Telescope Primary Mirror Segment Assemblies (PMSAs) and Secondary Mirror Assembly (SMA) were cleaned at the Johnson Space Center (JSC) in January 2018. In order to quantify the effectiveness of the cleaning, the same cleaning process was performed on the PMSA and SMA traveling witness wafers. These wafers have accompanied their respective mirror segments from their arrival at the Goddard Space Flight Center, through transport to JSC, and ultimately their exposure in Chamber A for cryogenic testing. The traveling wafers were analyzed using an Image Analysis automated microscope both prior to and after the cleaning. The resulting data showed that the PMSA wafers' Percent Area Coverage (PAC) reduced by 83.5% on average, from 0.1524 PAC to 0.0251 PAC. The SMA wafer's PAC decreased by 97.2%, from 0.1194 PAC to 0.0034 PAC. Further analysis of the particle size bins was completed in order to calculate their particle distribution slopes. The slope of the PMSA wafers increased by 0.025 on average, and the SMA wafer slope increased by 0.066. This indicates that the ratio of large to small particles slightly increased after the cleaning across all mirror segments. Visual inspections of the wafers and the flight PMSAs and SMA showed considerable and comparable particulate coverage improvements, thus leading to the conclusion that the average PAC on the PMSAs and SMA improved by the same factor as their respective wafers.

mirror↗
NASA NTRS2000

Critical Surface Cleaning and Verification Alternatives

As a result of federal and state requirements, historical critical cleaning and verification solvents such as Freon 113, Freon TMC, and Trichloroethylene (TCE) are either highly regulated or no longer 0 C available. Interim replacements such as HCFC 225 have been qualified, however toxicity and future phase-out regulations necessitate long term solutions. The scope of this project was to qualify a safe and environmentally compliant LOX surface verification alternative to Freon 113, TCE and HCFC 225. The main effort was focused on initiating the evaluation and qualification of HCFC 225G as an alternate LOX verification solvent. The project was scoped in FY 99/00 to perform LOX compatibility, cleaning efficiency and qualification on flight hardware.

Melton, Donald M.↗
NASA NTRS2008

Precision Cleaning - Path to Premier

ITT Space Systems Division s new Precision Cleaning facility provides critical cleaning and packaging of aerospace flight hardware and optical payloads to meet customer performance requirements. The Precision Cleaning Path to Premier Project was a 2007 capital project and is a key element in the approved Premier Resource Management - Integrated Supply Chain Footprint Optimization Project. Formerly precision cleaning was located offsite in a leased building. A new facility equipped with modern precision cleaning equipment including advanced process analytical technology and improved capabilities was designed and built after outsourcing solutions were investigated and found lacking in ability to meet quality specifications and schedule needs. SSD cleans parts that can range in size from a single threaded fastener all the way up to large composite structures. Materials that can be processed include optics, composites, metals and various high performance coatings. We are required to provide verification to our customers that we have met their particulate and molecular cleanliness requirements and we have that analytical capability in this new facility. The new facility footprint is approximately half the size of the former leased operation and provides double the amount of throughput. Process improvements and new cleaning equipment are projected to increase 1st pass yield from 78% to 98% avoiding $300K+/yr in rework costs. Cost avoidance of $350K/yr will result from elimination of rent, IT services, transportation, and decreased utility costs. Savings due to reduced staff expected to net $4-500K/yr.

Mackler, Scott E.↗
NASA NTRS1967

Liquid oxygen dicting cleaned by falling film method

Principle of a vertical falling film is used to clean contaminated large diameter and length liquid oxygen /LOX/ cylindrical ducting. The cleaning cycle is performed by flowing trichloroethylene in a falling film down a vertically mounted duct for approximately one hour.

Paul, H. I.↗
NASA NTRS1974

Auger electron spectroscopy and depth profile study of oxidation of modified 440C steel

Auger electron spectroscopy (AES) and sputtering were used to study selective oxidation of modified 440C steel. The sample was polycrystalline. Oxidation was performed on initially clean surfaces for pressures ranging from 1 x 10 to the minus 7th power to 1 x 10 to the minus 5th power torr and temperatures ranging from room temperature to 800 C. AES traces were taken during oxidation. In situ sputtering depth profiles are also obtained. A transition temperature is observed in the range 600 to 700 C for which the composition of the outer surface oxide changed from iron oxide to chromium oxide. Heating in vacuum about 5 x 10 to the minus 10 power torr to 700 C causes conversion of the iron oxide surface to chromium oxide.

Ferrante, J.↗