SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
A method of forming a battery electrode by forming, on a first substrate, a polymer template comprising interconnected polymer fibers, forming, on the polymer template, a carbon coating to form a carbon-coated polymer template, removing the carbon-coated polymer template from the first substrate, subsequent to removing the carbon-coated polymer template from the first substrate, removing the polymer template from the carbon coating, and disposing the carbon coating on a second substrate. A solid electrolyte interphase layer (SEI) comprising the carbon coating produced via the method, a battery electrode comprising such an SEI layer, and a battery comprising such a battery electrode are also provided.
Explore the source record for details and available documents.
The piezoresistance of carbon nanotube (CNT)-coated microfibers is examined using diametric compression. Diverse CNT forest morphologies were studied by changing the CNT length, diameter, and areal density via synthesis time and fiber surface treatment prior to CNT synthesis. Large-diameter (30–60 nm) and relatively low-density CNTs were synthesized on as-received glass fibers. Small-diameter (5–30 nm) and-high density CNTs were synthesized on glass fibers coated with 10 nm of alumina. The CNT length was controlled by adjusting synthesis time. Electromechanical compression was performed by measuring the electrical resistance in the axial direction during diametric compression. Gauge factors exceeding three were measured for small-diameter (<25 μm) coated fibers, corresponding to as much as 35% resistance change per micrometer of compression. The gauge factor for high-density, small-diameter CNT forests was generally greater than those for low-density, large-diameter forests. A finite element simulation shows that the piezoresistive response originates from both the contact resistance and intrinsic resistance of the forest itself. The change in contact and intrinsic resistance are balanced for relatively short CNT forests, while the response is dominated by CNT electrode contact resistance for taller CNT forests. These results are expected to guide the design of piezoresistive flow and tactile sensors.
LiMn x Fe 1-x PO 4 /C is considered a promising next-generation cathode material with significant commercial potential, inheriting the safety of LiFePO 4 while offering higher energy densities. However, the extremely low conductivity and the Jahn-Teller effect induced by Mn 3+ limit its practical capacity and rate performance. Effective modifications can be achieved through particle nanonization and uniform carbon coating. Here, in this work, we synthesized microspherical LiMn 0.6 Fe 0.4 PO 4 /C cathode materials using a hydrothermal method combined with spray drying carbon coating. The cathode material exhibits a microsphere structure composed of aggregated nanorods with a uniform 3 nm carbon coating, showing good dispersibility, small specific surface area and high tap density. In-situ diffraction analysis showed that expanding the single-phase solid solution region during (de)lithiation can reduce the energy barrier for electron transport, improve the kinetics of the (dis)charge process, and enhance both cycling and rate performance. The initial capacity at 0.1C can reach 155 mAh/g, and the capacity remains at 133.5 mAh/g with a retention rate of 97.1 % after 300 cycles. The synergistic effect of particle nanonization and uniform carbon coating endows the LiMn x Fe 1-x PO 4 /C material with excellent electrochemical performance.
Engineered functional surfaces play an important role to enable new products and manufacturing processes that can endure harsh service conditions such as high impact and contact loads, highly abrasive wear, extreme temperatures, and corrosive environments. Engineered surfaces can also be instrumental to improving the efficient use of energy by reducing frictional losses and extending service life. The main objective of this project was to develop a hybrid surface engineering technology that combines the advantages of a novel ultrafast boriding process with the next generation of superhard carbon coatings. The hypothesis was that this hybrid process will offer an unprecedented combination of wear and corrosion resistance, low frictional losses and affordability for treated parts so that it can be utilized in many applications. During this project, a duplex process was developed that combines the advantages of ultra-fast electrochemical boriding with those of hard tetrahedral amorphous carbon coatings. Both technologies can be combined to form a hybrid technology that is characterized by low friction and wear properties combined with corrosion and fatigue resistance. Good adhesion of both layers to each other was one main goal of this project, that has been achieved with HF1 adhesion through the Rockwell-C adhesion test. In this project, the mechanical properties of the hybrid coating were modeled through a finite-element analysis approach. We can conclude that the FEA model resembles the actual samples and be utilized to predict mechanical behavior under impacts. Based on this model, application-oriented load conditions can be simulated for optimal layer design regarding thickness and mechanical properties. To exemplify, one conclusion that can be drawn from the nanoindentation model is a boride layer thickness of 50 µm is sufficient to effectively support the carbon coating on the identified AISI 1045 low carbon steel substrate material. The duplex treatment yields wear rates as low as 6 x 10 -8 mm 3 N -1 m -1 and a coefficient of friction of 0.14 when tested against a steel counter face in a ball-on-disk test setup. On the other hand, the wear rate of the only-borided AISI 1045 steel was 5 x 10 -5 mm 3 N -1 m -1 , about three orders of magnitude higher than the duplex coating. At the same time, duplex treated samples experience corrosion resistance, which could not be achieved with single-layer carbon coatings. The developed surface treatment withstands a 3-hour exposure to 15% HCl, while the only carbon coated counter sample shows severe delamination of the coating due to pin hole corrosion. The boride layer is chemically stable and pin hole free because it is formed through an electrochemical process under high current densities (700 mA/cm 2 ) and high temperature. Additionally, the hybrid coating led to at least 3x increase in fatigue strength of the steel substrate, which exceeds the target performance of 30% improvement. There are numerous potential applications for the duplex coatings. A representative application is bearing ball coatings for off-shore windmills. Compared to currently employed surface technologies in this field, the initial costs of applying our technology might be higher due to more process steps but the performance benefits lead to an increased life time of treated parts, which will lower the maintenance and replacement costs in the long-term. To validate the technology for this specific application, the team is currently investigating the process of white etching crack initiation of the duplex coating in collaboration with ANL. Overall, this project successfully validated that the boride-carbon hybrid technology can withstand harsh conditions. One possible approach to commercialization under consideration is to transfer the technology to a startup or an existing coatings company.
Silicon is a high-energy density anode material for lithium-ion batteries, but it possesses shortcomings such as poor electronic conductivity, interfacial instability and mechanical fracturing that hinder its battery cycling. Carbon coating has been an important strategy for stabilizing silicon anodes, but the effects of the silicon surface properties on carbon coating morphology and the consequent silicon cycling stability have not been clearly elucidated. Herein, we find that thermal oxidation of the silicon anodes followed by chemical vapor deposition of carbonaceous precursors leads to a well-ordered graphene coating, whereas disordered graphite coating is formed on the native silicon surface. Graphene-coated silicon exhibits superior cycling performance, retaining a discharge capacity of ~1300 mAh g -1 after 300 cycles, whereas the disordered graphite-coated silicon suffers continuous degradation, retaining only~600 mAh g -1 after 300 cycles. Cryogenic electron microscopy reveals the mechanism behind the difference in cycling stabilities; graphene coated silicon is able to withstand the large mechanical strains induced during extended cycling, whereas disordered graphite coating is ruptured, exposing silicon surfaces to the electrolyte, leading to extensive buildup of SEI and poor cycling performance. Characterization of the silicon surface reveals that thermal treatment yields an oxygen-rich surface layer, which is hypothesized to play a decisive role in dictating the carbon coating. This work highlights the effect of silicon surface properties on carbon coating microstructure, and presents thermal treatment as a facile avenue to attain graphene coating on silicon anodes.
Here, carbon nanoelectrodes enable the detection of neurotransmitters at the level of single cells, vesicles, synapses and small brain structures. Previously, the etching of carbon fibers and 3D printing based on direct laser writing have been used to fabricate carbon nanoelectrodes, but these methods lack the ability of mass manufacturing. In this paper, we mass fabricate carbon nanoelectrodes by growing carbon nanospikes (CNSs) on metal wires. CNSs have a short, dense and defect-rich surface that produces remarkable electrochemical properties, and they can be mass fabricated on almost any substrate without using catalysts. Tungsten wires and niobium wires were electrochemically etched in batch to form sub micrometer sized tips, and a layer of CNSs was grown on the metal wires using plasma-enhanced chemical vapor deposition (PE-CVD). The thickness of the CNS layer was controlled by the deposition time, and a thin layer of CNSs can effectively cover the entire metal surface while maintaining the tip size within the sub micrometer scale. The etched tungsten wires produced tapered conical nanotips, while the etched niobium wires were long and thin. Both showed excellent sensitivity for the detection of outer sphere ruthenium hexamine and the inner sphere test compound ferricyanide. The CNS nanosensors were used for the measurement of dopamine, serotonin, ascorbic acid and DOPAC with fast-scan cyclic voltammetry. The CNS nanoelectrodes had a large surface area and numerous defect sites, which improved the sensitivity, electron transfer kinetics and adsorption. Finally, the CNS nanoelectrodes were compared with other nanoelectrode fabrication methods, including flame etching, 3D printing, and nanopipettes, which are slower to make and more difficult for mass fabrication. Thus, CNS nanoelectrodes are a promising strategy for the mass fabrication of nanoelectrode sensors for neurotransmitters.
A novel Au nanoparticle (AuNP)-biopolymer coated carbon screen-printed electrode (SPE) sensor was developed through the co-electrodeposition of Au and chitosan for mercury (Hg) ion detection. This new sensor showed successful Hg2+ detection in landfill leachate using square wave anodic stripping voltammetry (SWASV) with an optimized condition: a deposition potential of −0.6 V, deposition time of 200 s, amplitude of 25 mV, frequency of 60 Hz, and square wave step voltage of 4 mV. A noticeable peak was observed at +0.58 V associated with the stripping current of the Hg ion. The sensor exhibited a good sensitivity of ~0.09 μA/μg (~0.02 μA/nM) and a linear response over the concentration range of 10 to 100 ppb (50–500 nM). The limit of detection (LOD) was 1.69 ppb, which is significantly lower than the safety limit defined by the United States Environmental Protection Agency (USEPA). The sensor had an excellent selective response to Hg2+ in landfill leachate against other interfering cations (e.g., Zn2+, Pb2+, Cd2+, and Cu2+). Fifteen successive measurements with a stable peak current and a lower relative standard deviation (RSD = 5.1%) were recorded continuously using the AuNP-biopolymer-coated carbon SPE sensor, which showed excellent stability, sensitivity and reproducibility and consistent performance in detecting the Hg2+ ion. It also exhibited a good reliability and performance in measuring heavy metals in landfill leachate.
This work discusses a study on a surface treatment for creating extremely durable low-friction, wear and corrosion-resistant surfaces for tribological components in harsh conditions. A duplex surface treatment was developed that combines the advantages of ultra-fast electrochemical boriding with those of hard tetrahedral amorphous carbon coatings. The friction and wear properties of the duplex treatment are compared to the boride-only treatment of AISI 1045 steel, while corrosion and contact fatigue behaviors of the duplex layer are compared to that of the single-layer carbon coating on low carbon steel. The duplex treatment yields wear rates as low as 6 × 10−8 mm3·N−1·m−1 and a coefficient of friction of 0.14 when tested against a steel counter face. The contact fatigue impact tests reveal that the high hardness of 1200 HV0.05 of the borided layer in the duplex treatment leads to higher resistance against indentation but is accompanied by a higher incidence of crack initiation, being in good agreement with the finite-element modeling of nanoindentation results. The duplex coatings exhibit resistance to pinhole corrosion as evidenced by a 3 h exposure to 15% HCl at room temperature.
In this study, manganese-based Olivine is a promising cathode candidate with high energy and low cost for Li-ion batteries (LIBs). Its rate capability and cyclability challenges still remain even with nano-size and carbon coating. Herein, an ultrahigh rate performance is achieved by introducing an affinitive conductor to enhance the interfacial electron transport of LiMn 0.7 Fe 0.3 PO 4 via Li 3 V 2 (PO 4 ) 3 . It is found that the Li 3 V 2 (PO 4 ) 3 facilitates sp 2 hybridization to form a highly conductive carbon coating during the carbonized process. The composite 0.9LiMn 0.7 -Fe 0.3 PO 4 .0.1Li 3 V 2 (PO 4 ) 3 can deliver a capacity of 90.9 mAh g -1 and power density of 11444 W kg -1 at 50 C-rate. Both in situ X-ray diffraction and conductive-atomic force microscopy are conducted to understand the synergetic effect between LiMn 0.7 Fe 0.3 PO 4 and Li 3 V 2 (PO 4 ) 3 . The results suggest that the interfacial electron transfer between LiMn 0.2 Fe 0.3 PO 4 particles and the electron conducting medium, such as binder/carbon black composite, is greatly improved so that the highly Li + conductive nature of olivine materials can be fully unleashed. This work demonstrates the importance of efficient interfacial electron transfer to the active cathode particles, and opens up a new venue for the rational design of high-energy and high-power batteries.
A novel hybrid structure has been developed by growing carbon nanotubes (CNTs) on a metal mesh that functions as a literally unlimitedly extendable backbone. This hybrid material structure provides a new approach of extending CNTs’ advantageous properties such as ultrahigh thermal and electrical conductivities, high sensitivity to gases, and distinctive wettability for different liquids with chemical inertness to macroscale—otherwise available only in nano- and microscales. In this feasibility work, CNTs were grown on a Type 316 stainless steel (SS) mesh by self-catalytical chemical vapor deposition (CVD) without the need of an externally added catalyst or catalyst support. For the radially aligned and entangled CNT forest on the SS mesh, the average CNT diameter is around 50 nm, while the length varies from 20 to 25 µm. High-resolution transmission electron microscopy analysis revealed the multiwall structure of the CNTs with >30 rolled-up graphitic sheets. Raman spectra of the CNTs showed a dominant G band, indicating a well-ordered graphitic nanostructure. Being highly hydrophobic with a water contact angle of ∼145° and oleophilic, the CNT-coated SS mesh could be used in fluid separation and organic contaminant removal from water. Moreover, CNTs are recognized for their exceptional thermal conductivity and the CNT-coated mesh offers a supportive structure with directly connected CNTs for efficient heat transfer. Proof of concept has been achieved for the CNT-coated mesh’s potentials as a liquid filter and an thermal interface material (TIM). Specifically, the CNT-coated mesh demonstrated the capability of capturing water from a water-organic mixture with a 100 % efficiency while allowing organic liquids to pass through the filter. Furthermore, when used as a TIM, the CNT-coated mesh reduced the interfacial thermal impedance by >30 %.
Superlubricity, i.e., coefficient of friction (COF) below 0.01, was earlier limited to microscale in controlled environments in the earlier literature and more recently realized for macroscale sliding of ceramic or carbon surfaces lubricated by water or other polar fluids. However, there is lack of report of superlubricity for the most common bearing system, i.e., steel-steel contact in non-polar oil lubrication. Here, in this work, we present ultra-low COF of 0.001–0.007 by using a sacrificial coating composed of vertically-aligned carbon nanotubes (CNTs) for macroscale steel-steel sliding under minimum quantity lubrication (MQL) of a polyalphaolefin (PAO) oil in the ambient environment. Raman spectroscopy and electron microscopy analyses detected graphene-containing tribofilms on both the steel surfaces, which was produced by the fractured CNT flakes and metallic wear debris during running-in. The in situ formed graphene-graphene contact interface presumably possesses a low shear resistance leading to superlubricity. The presence of oil, despite as little as one droplet, has proven to be crucial. Such a superlubricity performance has shown good sustainability in extended testing of more than 500,000 cycles and strong ability of accommodating changes in sliding conditions. Results here demonstrate feasibility with fundamental insights for achieving ambient environment macroscale superlubricity.
Sodium fluorophosphate Na 2 FePO 4 F holds great potential for sodium-ion batteries due to its high theoretical capacity, excellent structural stability, abundant resources, and affordability. However, its poor electronic and ionic conductivities limit its practical applications. Therefore, ion doping and carbon coating have been employed as synergistic strategies in this study to overcome these limitations. A one-step, energy-efficient solid-state method using sucrose as a carbon coating source was used to synthesize Na 2 FePO 4 F/C (NFPF/C) and its doped variant, Na 2 Fe 0.85 V 0.1 PO 4 F/C (NFVPF/C). 23 Na-MAS-NMR spectra confirm the existence of two distinct sites for sodium (Na1/Na2). The ex-situ 23 Na-MAS-NMR performed at different states-of-charge reveals the activity of only one sodium. The scanning electron microscopy findings reveal a reduction in the particle size with V-introduction, enhancing the energetic performances. NFVPF/C delivers higher specific capacity of 122 mAh g −1 compared to 116 mAh g −1 for NFPF/C at 0.1C. It also demonstrates improved cycling stability, retaining 81 % of its initial capacity after 120 cycles, in contrast to 46 % for the pristine material. The doped phase outperforms the pristine at higher current rates, delivering specific capacities of 81 and 55 mAh g −1 at 2C and 3C, respectively, compared to 35 and 17 mAh g −1 for NFPF/C.
Abstract The unique capability of 3D printing to create geometric complex structures presents a promising avenue for producing 3D electrodes aimed at enhancing power and energy densities within constrained spaces, which is challenging to achieve through traditional slurry casting methods. However, despite advancements over the years, 3D‐printed batteries have faced limitations in terms of mechanical robustness to endure significant volume changes during cycling and restricted electrochemical performance due to the lack of adequate electrode feedstock development or post‐processing treatments. Herein, a high‐loaded electrode filament with ≈65 wt.% fillers, enabling the fabrication of structural electrodes with improved electrochemical performance and superior mechanical properties, is developed. Through a combination of 3D printing and post‐processing techniques, interdigitated structures with high areal‐loading density, resulting in a full cell with an enhanced areal capacity of ≈12.28 mAh cm −2 at ≈0.92 mA cm −2 is fabricated. Moreover, the structural batteries, treated through the carbonizing process, are integrated by the carbon coating generated during carbonization, exhibiting remarkable compressive properties (with a modulus of 18.5 MPa and a strength of 1.09 MPa). Overall, the findings demonstrate the promising potential of 3D printed batteries for practical applications, while showcasing the scalability and design flexibility offered by 3D printing technology.
Carbon steel is a widely used structural material; however, it lacks corrosion resistance in water environments. An alternative approach to overcome this challenge is to implement the deposition of inherently corrosion-resistant ceramic coatings. SiC/C/Al coatings were developed at 700°C, using polycarbosilane in combination with Al and C, which were included as active and passive fillers, respectively. Here, we show that it is necessary to use Al particle sizes below 10 µm for them to function as an active filler below 900°C. Owing to their laminar microstructure, these coatings showed a cohesive delamination with an adhesion strength of 10 MPa. Results demonstrated that these coatings were able to reduce the corrosion of carbon steel in saline water by 99.7%, with corrosion rates of 38.33 mpy for carbon steel, and 0.099 and 0.155 mpy for SiC/C and SiC/C/Al (10 µm) coatings, respectively.
Contact resistance between the cathode active material (CAM) and the Al current collector can be reduced by applying carbon coatings to the Al current collector surface. However, this process requires an additional step of carbon layer coating on the current collector, which increases both manufacturing costs and processing time. In the present work, an interlayer of continuous unsized carbon fibers aligned in one direction (CF interlayer), is introduced between the Al current collector and the NMC811 cathode during cathode deposition on the Al current collector. This single-step approach eliminates the need for the additional carbon layer coating on the current collector. Additionally, this approach removes the use of toxic solvents and insulative polymers used for making the carbon coating. The CF interlayer improves the rate capability at higher C-rates. The CF interlayer lowers the contact resistance between the cathode particles and the current collector while improving the activation energy of charge transfer. The peel test showed that the CF interlayer does not affect the adhesion strength of the cathode layer with the current collector.