Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capsule”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Experimental Investigation of Roughness Effects on Transition on Blunt Spherical Capsule Shapes

The present contribution reviews recent experimental results of roughness effects on boundary layer transition on capsule geometries with spherical windward geometries. Experiments in three wind tunnel facilities are considered. The ACE Tunnel of Texas AM University, USA, provided Mach 6 experiments with distributed roughness at relatively low Reynolds numbers, 2.5 · 10(exp 5) < Re(sub d) < 5 · 10(exp 5), with d denoting the capsule diameter. The observed boundary layer transition compared well with correlations based on transient growth theory, even though the roughness heights were in the order of boundary layer thickness. Larger Reynolds numbers, 1 · 10(exp 6) < Re(sub d) < 3·10(exp 6), could be assessed in the hypersonic Ludwieg tube, HLB, of TU Braunschweig, Germany. Transition is observed at rather low, subcritical roughness values in the order of 20 μm for a roughness patch placed about the geometric center of the capsule model. These experiments varied fluctuation levels of the freestream. The authors assume that the observed transitions that occur downstream of the subcritical roughness patch are due to freestream disturbances in the tunnel, which interact with small roughness heights. Additional experiments in the HLB facility with patches of larger roughness height support the relevance of transient growth theory for low-to-medium roughness heights, relative to boundary layer thickness. The effects of Reynolds numbers and total flow enthalpy on transition with isolated roughness were investigated in the HIEST facility of JAXA, Japan. Here, a model insert with roughness elements of varying height for tripping transition to turbulence was employed. The results are compared to known trip effectiveness correlations for isolated roughness. Overall, the transient growth correlation seems to represent roughness-induced transition behavior on the ACE and HLB entry capsule shapes with roughness over the entire capsule surface. These experiment are however for perfect gases. Comparable experiments on roughness induced transition in a high-enthalpy facility are still needed to confirm the validity of transient-growth correlation for vehicle design.

Radespiel, Rolf↗
DOE OSTI2026

STANDARD REFERENCE MATERIAL CHARPY TESTING FROM HIGH FLUENCE SURVEILLANCE CAPSULE

The Palisades Nuclear Generating Station included in its original surveillance program a surveillance capsule, designated A-60. The capsule was removed from its surveillance position in early 1995 and has been resident in the spent fuel pool since that time. It was harvested to perform characterization of surveillance specimens in this capsule in 2023. This capsule was irradiated to a fluence of 1.96x1020 n/cm2 (E> 1MeV) that is equivalent for more than 150 effective full power years for the current US reactor pressure vessel (RPV) fleet. This capsule contained several materials, including Charpy specimens of standard reference material (SRM) from Heavy-Section Steel Technology (HSST) A533-B Plate 01. To perform Charpy testing of this highly irradiated material, the new Charpy specimen transfer system was designed and implemented on Charpy impact testing machine in the hot cell to accommodate remote testing of these specimens. This new transfer system includes integrated environmental chamber to cool or heat Charpy specimens to the desired temperature. Testing of this highly irradiated material revealed very large shift of Charpy transition temperature, 188oC.

Sokolov, Mikhail [ORNL] (ORCID:0000000256373346)↗
DOE OSTI2026

Fully Additively Manufactured Wetted Foam Capsules for Inertial Confinement Fusion

In the pursuit of realizing reliable clean energy generation via inertial confinement fusion (ICF), wetted foam (WF) capsule targets have long been coveted due to their potential to simplify the target fielding process and suppress hydrodynamic instabilities and material mixing that limit achievable energy output, yet producing and deploying a WF target has proven challenging. Here, in this work, we demonstrate the design, fabrication, metrology, and testing of fully additively manufactured (AM) foam-lined capsules using two-photon polymerization (2PP) for ICF. We successfully fielded an AM polymeric foam capsule with a 3-mm outer diameter, a nominally 15-µm-thick solid outer layer, a 120-µm-thick inner foam layer, and a 250-µm outer diameter copper fill tube on the National Ignition Facility for a polar direct-drive shot, and we showcase deuterium wetting of the capsule foam layer inside an ignition target proofing station. Our exploration showed that 2PP can produce fieldable targets with complex geometries and potentially shorten the design iteration turnaround time and the overall target fabrication time.

Target↗
DOE OSTI2025

Additively Manufactured Pressure Limiting Irradiation Capsule for the High Flux Isotope Reactor

The Advanced Materials and Manufacturing Technologies (AMMT) program previously demonstrated an additively manufactured (AM) irradiation capsule (commonly referred to as a “rabbit”) from 316H stainless steel (SS) for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL)1. This report details efforts to design and fabricate an AM pressure limiting structure (PLS) into one of the end caps of a rabbit capsule and qualify it for insertion into HFIR. The PLS includes a thin cylindrical rupture wall, a shield, and internal supports to facilitate printing and ensure mechanical integrity. Its overall dimensions are 9-mm tall and 10-mm in diameter— equivalent to about one-fourth of the size of a AAA battery. The PLS maintains safe internal operating pressures for a rabbit capsule while in the reactor. Although this application is specific to HFIR, the approach lends itself to further applications in industrial, aeronautical, advanced space and power generation environments. Several PLS rabbits capsules have been successfully designed, fabricated, pressure tested, and qualified for future insertion into the HFIR for irradiation and post-irradiation evaluation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

CNL Calandria Lifetime Extension Program: 1st Capsule Assembly

This report provides documentation and a summary of all 18 capsules assembled for the Canadian Nuclear Laboratories (CNL) Calandria Lifetime Extension Program. This is the first set of capsules in a series of two irradiation campaigns to provide data relevant to weldments in the calandria of Canada deuterium uranium (CANDU) reactors. This report provides documentation on capsule IDs, specimen IDs, and capsule locations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Irradiation of Advanced Cladding Specimens in the High Flux Isotope Reactor: Capsule Designs and Test Matrix

The Advanced Fuels Campaign (AFC) has initiated the Advanced Reactor Cladding (ARC) irradiation campaign to generate irradiation performance data for candidate fuel cladding concepts. The campaign includes a diverse set of ferritic/martensitic steels, oxide dispersion strengthened (ODS) alloys, FeCrAlbased alloys, coated materials, and welded cladding specimens produced through multiple US Department of Energy (DOE) programs and international collaborations. Three complementary experimental thrusts comprise the campaign: tensile testing (ARC Tensile) to rapidly screen candidate alloys, fracture toughness testing (ARC Fracture) to evaluate irradiation effects on crack resistance, and tubular weld testing (ARC Weld) to quantify irradiation-induced changes in the mechanical performance of end cap welds. This report documents the irradiation campaign design, including the selected materials, specimen types, irradiation matrix, and capsule designs for irradiation within the High Flux Isotope Reactor (HFIR). A total of 14 irradiation capsules were developed to achieve target irradiation temperatures between 300°C and 600°C and doses up to 30 dpa. Thermal analyses were performed using finite element methods to establish capsule geometries capable of achieving the desired specimen temperatures while accommodating differences in specimen geometry and material properties. The resulting capsule designs provide the basis for irradiation of the AFC-ARC experimental matrix and subsequent post-irradiation examination to assess the effects of neutron irradiation on advanced cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1967

Program for calculating optimum dimensions of alpha radioisotope capsules exposed to varying stress and temperature

A method and computer program were developed for calculating the creep and optimizing the dimensions of capsules filled with alpha-emitting radioisotopes. The method solves an integral equation that was developed assuming linear accumulation of partial creep lives and relating life to time-dependent stress and temperature using the Larson-Miller parameter. The computer program, CAPSUL, is written in Fortran language for the IBM 360/75 computer. The program makes a least squares fit of the creep life function using conventional constant stress, constant temperature creep data. Dimensions of capsules having maximum thermal power per unit of weight, volume, or area are calculated for a given creep life and pressure-temperature history using a numerical Lagrange Multiplier formulation. The program also calculates the life to a prescribed strain for capsules of given dimensions and pressure-temperature history. The method has been used to analyze creep data for the alloys 304 stainless steel, Hastelloy N, Cb-1% Zr, FS-85, and T-222.

J. P. Nichols↗
NASA NTRS1973

Gettering capsule for removing oxygen from liquid lithium systems

Capsule consisting of tantalum shell lined with tantalum screen and partially filled with lithium and pieces of yttrium is immersed in hot lithium stream. Oxygen is removed from stream by being absorbed by gettering capsule. Oxygen passes through capsule wall and into lithium inside capsule where it reacts with yttrium to form Y2O3.

Tower, L. K.↗
NASA NTRS1974

Long-duration life tests of slip ring capsule assemblies for inertial guidance platforms

Eight slip ring capsules, each having 80 or 100 circuits, were operated for time periods ranging from 14,300 hours to 24,700 hours. The test mode simulated the motion of gimbal axes of the Saturn inertial guidance the platform in an organic free nitrogen environment. Computer-compiled noise data (approximately 45,000 recordings) were graphed as a function of test time and position within the capsules and as extreme probability distributions. Greater than ninety-nine percent of the noise measurements for the capsules with sufficient lubrication were less than 10 milliohms. Capsules with glass dielectrics did not perform significantly differently than those with filled epoxy dielectrics. The initial wear mode of prow formation was followed by rider wear. After 10 to the 8th power wipes, ring wear depth did not exceed the surface finish and the radial rider wear depth was less than 13 microns.

Cole, S. R.↗
NASA NTRS1975

Design, fabrication, and operation of capsules for the irradiation testing of candidate advanced space reactor fuel pins

Fuel irradiation experiments were designed, built, and operated to test uranium mononitride (UN) fuel clad in tungsten-lined T-111 and uranium dioxide fuel clad in both tungsten-lined T-111 and tungsten-lined Nb-1% Zr. A total of nine fuel pins was irradiated at average cladding temperatures ranging from 931 to 1015 C. The UN experiments, capsules UN-4 and -5, operated for 10,480 and 10,037 hr, respectively, at an average linear heat generation rate of 10 kW/ft. The UO2 experiment, capsule UN-6, operated for 8333 hr at an average linear heat generation rate of approximately 5 kW/ft. Following irradiation, the nine fuel pins were removed from their capsules, externally examined, and sent to the NASA Plum Brook Facility for more detailed postirradiation examination. During visual examination, it was discovered that the cladding of the fuel pin containing dense UN in each of capsules UN-4 and -5 had failed, exposing the UN fuel to the NaK in which the pins were submerged and permitting the release of fission gas from the failed pins. A rough analysis of the fission gas seen in samples of the gas in the fuel pin region indicated fission gas release-to-birth rates from these fuel pins in the range of .00001.

Thoms, K. R.↗
NASA NTRS1997

Entry Dispersion Analysis for the Stardust Comet Sample Return Capsule

Stardust will be the first mission to return samples from beyond the Earth-Moon system. The sample return capsule, which is passively controlled during the fastest Earth entry ever, will land by parachute in Utah. The present study analyzes the entry, descent, and landing of the returning sample capsule. The effects of two aerodynamic instabilities are revealed (one in the high altitude free molecular regime and the other in the transonic/subsonic flow regime). These instabilities could lead to unacceptably large excursions in the angle-of-attack near peak heating and main parachute deployment, respectively. To reduce the excursions resulting from the high altitude instability, the entry spin rate of the capsule is increased. To stabilize the excursions from the transonic/subsonic instability, a drogue chute with deployment triggered by an accelerometer and timer is added prior to main parachute deployment. A Monte Carlo dispersion analysis of the modified entry (from which the impact of off-nominal conditions during the entry is ascertained) shows that the capsule attitude excursions near peak heating and drogue chute deployment are within Stardust program limits. Additionally, the size of the resulting 3-sigma landing ellipse is 83.5 km in downrange by 29.2 km in crossrange, which is within the Utah Test and Training Range boundaries.

Desai, Prasun N.↗
NASA NTRS1998

Aerothermal Effects of Cavities and Protuberances for High-Speed Sample Return Capsules

Extraterrestrial sample return is a growing component of solar system exploration. Currently, four missions, Stardust, 1 Muses-C, 2 Genesis, and Mars Sample Return, are under development that employ sample return as a prime component of the mission architecture. Respectively, these missions will return samples from the tail of a comet, an asteroid, the solar wind, and, Mars. An important component of these missions and the focus of this paper is the design of the sample return capsule (SRC). The purpose of the SRC is to safely return to Earth any gathered samples for terrestrial analysis. The two major design constraints for any SRC are as follows: 1) it must be able to survive a high-speed Earth entry (11 km/s to as a high as 15 km/s), 2) the mass of the SRC must be as small as possible. Because the SRC mass is carried from Earth to the sample sight and back, the SRC mass is a strong driver in the mission mass budget. Further, for the Mars Sample Return Capsule, planetary protection is another constraint. For this capsule, the probability of planetary contamination at Earth due to an SRC failure at entry must be minimal. For an SRC, a possible failure mechanism is severe local heating as a result of cavities and or protuberances in the SRC forebody heatshield. For example, the Apollo Command Module had a number of cavities and protuberances as part of the baseline designs Wind-tunnel tests of models containing small cavities and protuberances showed severe local heating augmentations in the vicinity of these surface discontinuities.4-5 As another example, the Genesis SRC forebody heat-shield contains penetrations (cavities) to mount the vehicle to the carrier bus. It is expected that these penetrations will also experience a severe local heating environment. A concern is that the large thermal gradients may produce sufficient thermal stress to cause local mechanical failure of the heatshield. Penetrations to the forebody heat-shield can also result from damage at vehicle integration, during launch, or during transportation of the sample return capsule from earth to the sample site and back. For example, the Starting SRC was damaged near the shoulder during the heatshield integration process producing a local surface discontinuity. Also, the Starting SRC traverses through the tail of a comet and is in space for 7 years. Thus, damage to the heatshield as a result of micrometeroid impact is a concern. Finally, it is difficult to characterize the effects of these potential heatshield singularities with ground-test facilities. Either detailed simulation or a dedicated flight test is required.

Olynick, David↗
NASA NTRS2005

Ballistic Range Testing of the Mars Exploration Rover Entry Capsule

Results from a 25 shot ballistic range test of the Mars Exploration Rover (MER) aeroshell are presented. The supersonic pitch damping properties of the MER capsule were characterized between Mach = 1.5 and Mach = 3.5 and total angles-of-attack from 0 degrees to greater than 25 degrees. Three capsule center-of-gravity positions were tested across this range of conditions, 0.27, 0.30 and 0.33 body diameters aft of the nose. Parameter identification results show that the capsule is dynamically unstable at low angles-of-attack across the Mach numbers tested, with instability increasing with lower speeds. This dynamic instability was seen to increase with aft center-of-gravity movement. The MER outer mold line was very similar to the successful Mars Pathfinder capsule with only minor modifications. Pathfinder relied on Viking forced oscillation data for preflight predictions. The pitch damping data calculated from this test program are shown to more accurately reproduce the measured Path finder flight data.

Schoenenberger, Mark↗
NASA NTRS2009

Using Numerical Modeling to Simulate Space Capsule Ground Landings

Experimental work is being conducted at the National Aeronautics and Space Administration s (NASA) Langley Research Center (LaRC) to investigate ground landing capabilities of the Orion crew exploration vehicle (CEV). The Orion capsule is NASA s replacement for the Space Shuttle. The Orion capsule will service the International Space Station and be used for future space missions to the Moon and to Mars. To evaluate the feasibility of Orion ground landings, a series of capsule impact tests are being performed at the NASA Langley Landing and Impact Research Facility (LandIR). The experimental results derived at LandIR provide means to validate and calibrate nonlinear dynamic finite element models, which are also being developed during this study. Because of the high cost and time involvement intrinsic to full-scale testing, numerical simulations are favored over experimental work. Subsequent to a numerical model validated by actual test responses, impact simulations will be conducted to study multiple impact scenarios not practical to test. Twenty-one swing tests using the LandIR gantry were conducted during the June 07 through October 07 time period to evaluate the Orion s impact response. Results for two capsule initial pitch angles, 0deg and -15deg , along with their computer simulations using LS-DYNA are presented in this article. A soil-vehicle friction coefficient of 0.45 was determined by comparing the test stopping distance with computer simulations. In addition, soil modeling accuracy is presented by comparing vertical penetrometer impact tests with computer simulations for the soil model used during the swing tests.

Heymsfield, Ernie↗
NASA NTRS2011

Airborne Observation of the Hayabusa Sample Return Capsule Re-Entry

The Japan Aerospace Exploration Agency (JAXA) recently completed their Hayabusa asteroid exploration mission. Launched in 2003, Hayabusa made contact with, and retrieved a sample from, the near-Earth asteroid Itokawa in 2005. The sample return capsule (SRC) re-entered over the Woomera Test Range (WTR) in southern Australia on June 13, 2010, at approximately 11:21 pm local time (09:51 UTC). The SRC re-entry velocity was 12.2 km/s, making it the second-fastest Earth return velocity behind NASA s Stardust sample return capsule re-entry in 2006. From a space technology development perspective, Hayabusa s re-entry functioned as a rare flight experiment of an entry vehicle and its thermal protection system. In collaboration with the SETI Institute, NASA deployed its DC-8 airborne laboratory and a team of international researchers to Australia to observe the re-entry of the SRC. The use of an airborne platform enables observation above most clouds and weather and greatly diminishes atmospheric absorption of the optical signals. The DC-8 s flight path was engineered and flown to provide a view of the spacecraft that bracketed the heat pulse to the capsule. A suite of imaging instruments on board the DC-8 successfully recorded the luminous portion of the re-entry event. For approximately 70 seconds, the spectroscopic and radiometric instruments acquired images and spectra of the capsule, its wake, and destructive re-entry of the spacecraft bus. Figure 1 shows a perspective view of the WTR, the SRC re-entry trajectory, and the flight path of the DC-8. The SRC was jettisoned from the spacecraft bus approximately 3 hours prior to entry interface. Due to thruster failures on the spacecraft, it could not be diverted from the entry path and followed the trajectory of the SRC, where it burned up in the atmosphere between approximately 100 and 50 km altitude. Fortuitously, the separation distance between the spacecraft and SRC was sufficient to clearly resolve the SRC from the debris field of the burning spacecraft. Figure 2 shows a frame from a high-definition television camera on board the aircraft and denotes the locations of the SRC and spacecraft bus debris.

Grinstead, Jay H.↗
NASA NTRS2014

Visualization of Flow Separation Around an Atmospheric Entry Capsule at Low-Subsonic Mach Number Using Background-Oriented Schlieren (BOS)

This paper presents the results of visualization of separated flow around a generic entry capsule that resembles the Apollo Command Module (CM) and the Orion Multi-Purpose Crew Vehicle (MPCV). The model was tested at flow speeds up to Mach 0.4 at a single angle of attack of 28 degrees. For manned spacecraft using capsule-shaped vehicles, certain flight operations such as emergency abort maneuvers soon after launch and flight just prior to parachute deployment during the final stages of entry, the command module may fly at low Mach number. Under these flow conditions, the separated flow generated from the heat-shield surface on both windward and leeward sides of the capsule dominates the wake flow downstream of the capsule. In this paper, flow visualization of the separated flow was conducted using the background-oriented schlieren (BOS) method, which has the capability of visualizing significantly separated wake flows without the particle seeding required by other techniques. Experimental results herein show that BOS has detection capability of density changes on the order of 10(sup-5).

Mizukaki, Toshiharu↗
NASA NTRS2016

Infrared Observations of the Orion Capsule During EFT-1 Hypersonic Reentry

High-resolution infrared observations of the Orion capsule during its atmospheric reentry on December 5, 2015 were made from a US Navy NP-3D. This aircraft, equipped with a long-range optical sensor system, tracked the capsule from Mach 10 to 7 from a distance of approximately 60 nmi. Global surface temperatures of the capsule's thermal heatshield were derived from near infrared intensity measurements. The global surface temperature measurements complemented onboard instrumentation and were invaluable to the interpretation of the in-depth thermocouple measurements which rely on inverse heat transfer methods and material response codes to infer the desired surface temperature from the sub-surface measurements. The full paper will address the motivations behind the NASA Engineering Safety Center sponsored observation and highlight premission planning processes with an emphasis on aircraft placement, optimal instrument configuration and sensor calibrations. Critical aspects of mission operations coordinated from the NASA Johnson Spaceflight Center and integration with the JSC Flight Test Management Office will be discussed. A summary of the imagery that was obtained and processed to global surface temperature will be presented. At the capsule's point of closest approach relative to the imaging system, the spatial resolution was estimated to be approximately 15-inches per pixel and was sufficient to identify localized temperature increases associated with compression pad support hardware on the heatshield. The full paper will discuss the synergy of the quantitative imagery derived temperature maps with in-situ thermocouple measurements. Comparison of limited onboard surface thermocouple data to the image derived surface temperature will be presented. The two complimentary measurements serve as an example of the effective leveraging of resources to advance the understanding of high Mach number environments associated with an ablated heatshield and provide unique data for the validation of design tools and numerical flight simulation techniques. Collaborative opportunities and technology investments in support of planned observations of NASA's next Orion flight test in 2018 will be explored in the full manuscript.

Horvath, Thomas J.↗
NASA NTRS2019

Modal Analysis of the Orion Capsule Two Parachute System

As discussed in Ref [1], it is apparent from flight tests that the system made up of two main parachutes and a capsule can undergo several distinct dynamical behaviors. The most significant and problematic of these is the pendulum mode in which the system develops a pronounced swinging motion with an amplitude of up to 24 deg. Large excursions away from vertical by the capsule could cause it to strike the ground at a large horizontal or vertical speed and jeopardize the safety of the astronauts during a crewed mission. In reference [1], Ali et al. summarized a series of efforts taken by the Capsule Parachute Assembly System (CPAS) Program to understand and mitigate the pendulum issue. The period of oscillation and location of the system's pivot point are determined from post-flight analysis. Other noticeable but benign modes include: 1) flyout (scissors) mode, where the parachutes move back and forth symmetrically with respect to the vertical axis similar to the motion of a pair of scissors; 2) maypole mode, where the two parachutes circle around the vertical axis at a nearly constant radius and period; and 3) breathing mode, in which deformation of the non-rigid canopies affects the axial acceleration of the system in an oscillatory manner. Because these modes are relatively harm- less, little effort has been devoted to analyzing them in comparison with the pendulum motion. Motions of the actual system made up of two parachutes and a capsule are extremely complicated due to nonlinearities and flexibility effects. Often it is difficult to obtain insight into the fundamental dynamics of the system by examining results from a multi-body simulation based on nonlinear equations of motion (EOMs). As a part of this study, the dynamics of each mode observed during flight is derived from first principles on an individual basis by making numerous simplifications along the way. The intent is to gain a better understanding into the behavior of the complex multi-body system by studying the reduced set of differential equations associated with each mode. This approach is analogous to the traditional modal analysis technique used to study airplane flight dynamics, in which the full nonlinear behavior of the airframe is decomposed into the phugoid and short period modes for the longitudinal dynamics and the spiral, roll-subsidence, and dutch-roll modes for the lateral dynamics. It is important to note that the study does not address the mechanisms that cause the system to transition from one mode to another, nor does it discuss motions during which two or more modes occur simultaneously.

Pei, J.↗