Advances in Turbine-Engine Technology
Status report describes major advances in high-temperature materials, coatings, and turbine-blade coating technology for aircraft turbine engines, which are keys to achieving improved performance.
Freche, J. C.↗
SEARCH · Engineering Papers
Results for “blade coating”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of a Wind Turbine Blade Surface Coating to Reduce Damage due to Lightning
Explore the source record for details and available documents.
17 WIND ENERGY↗
Internal coating of air cooled gas turbine blades
Six coating systems were evaluated for internal coating of decent stage (DS) eutectic high pressure turbine blades. Sequential deposition of electroless Ni by the hydrazine process, slurry Cr, and slurry Al, followed by heat treatment provided the coating composition and thickness for internal coating of DS eutectic turbine blades. Both NiCr and NiCrAl coating compositions were evaluated for strain capability and ductile to brittle transition temperature.
Ahuja, P. L.↗
The effect of adding roughness and thickness to a transonic axial compressor rotor
The performance deterioration of a high speed axial compressor rotor due to surface roughness and airfoil thickness variations is reported. A 0.025 mm (0.001 in.) thick rough coating with a surface finish of 2.54-3.18 RMS microns (100-125 RMS microinches) is applied to the pressure and suction surface of the rotor blades. Coating both surfaces increases the leading edge thickness by 10% at the hub and 20% at the tip. Application of this coating results in a loss in efficiency of 6 points and a 9% reduction in the pressure ratio across the rotor at an operating condition near the design point. To separate the effect of thickness and roughness, a smooth coating of equal thickness is also applied to the blade. The smooth coating surface finish is 0.254-0.508 RMS microns (10-20 RMS microinches), compared to the bare metal blade surface finish of 0.508 RMS microns (20 RMS microinches). The smooth coating results in approximately half of the performance deterioration found from the rough coating. Both coatings are then applied to different portions of the blade surface to determine which portions of the airfoil are most sensitive to thickness/roughness variations. Aerodynamic performance measurements are presented for a number of coating configurations at 60%, 80%, and 100% of design speed. The results indicate that thickness/roughness over the first 10% of blade chord accounts for virtually all of the observed performance degradation for the smooth coating, compared to about 70% of the observed performance degradation for the rough coating. The performance deterioration is investigated in more detail at design speed using laser anemometer measurements as well as predictions generated by a quasi-3D Navier-Stokes flow solver which includes a surface roughness model. Measurements and analysis are performed on the baseline blade and the full-coverage smooth and rough coatings. The results indicate that coating the blade causes a thickening of the blade boundary layers. The interaction between the rotor passage shock and the thickened suction surface boundary layer then results in an increase in blockage which reduces the diffusion level in the rear half of the blade passage, thus reducing the aerodynamic performance of the rotor.
Suder, Kenneth L.↗
Formation trajectories of solution-processed perovskite thin films from mixed solvents
The engineering of mixed-solvent formulations and their evaporation conditions are key to reproducible perovskite coatings for high-performance photovoltaics. Here, we report a lumped-parameter evaporation model to predict the evolution of a perovskite ink liquid film over time (solvent ratio, solute concentration, and film thickness). The drying-rate model is validated via in situ film-thickness measurements, and the predicted transient liquid film state is mapped as a process path. These methods allow for the prediction of process sensitivity to local environmental factors and the understanding and visualization of a broader processing parameter space enabled through the coupling of process and ink engineering. Process maps are applied to create a new framework for scalable perovskite coating development with a goal of improving the reproducibility and transferability of perovskite fabrication. This approach is demonstrated with blade-coated FA 0.83 Cs 0.17 PbI 3 photovoltaic devices, improving the photovoltaic conversion efficiency from 17.5% ± 1.7% to 20.3% ± 0.6%.
14 SOLAR ENERGY↗
Advancements in Manufacturing of High-Performance Perovskite Solar Cells and Modules Using Printing Technologies
Perovskite photovoltaic technology carries immense opportunity for the solar industries because of its remarkable efficiency and prospect for cost-effective production. However, the successful deployment of perovskite solar modules (PSMs) in the solar market necessitates tackling stability-based obstacles, scalability, and environmental considerations. This paper unveils a comprehensive examination of the cutting-edge advancements in the manufacturing of perovskite solar cells (PSCs) and modules, with an emphasis on high-speed, large-area printing. The paper underscores the substantial progress achieved in printed PSCs and PSMs, demonstrating promising electrical performance and long-term device durability. This review paper categorizes printing techniques compatible with large-area high-speed manufacturing into three distinct families: blade coating, slot die coating, and screen printing, as these common printing practices offer precise control, scalability, cost-effectiveness, high resolution, and efficient material usage. Additionally, this paper presents an in-depth investigation and comparison of superior PSCs and PSMs fabricated by printing on power conversion efficiency (PCE), stability, and scalability.
14 SOLAR ENERGY↗
Scalable and Quench-Free Processing of Metal Halide Perovskites in Ambient Conditions
With the rise of global warming and the growing energy crisis, scientists have pivoted from typical resources to look for new materials and technologies. Perovskite materials hold the potential for making high-efficiency, low-cost solar cells through solution processing of Earth-abundant materials; however, scalability, stability, and durability remain key challenges. In order to transition from small-scale processing in inert environments to higher throughput processing in ambient conditions, the fundamentals of perovskite crystallization must be understood. Classical nucleation theory, the LaMer relation, and nonclassical crystallization considerations are discussed to provide a mechanism by which a gellan gum (GG) additive—a nontoxic polymeric saccharide—has enabled researchers to produce quality halide perovskite thin-film blade coated in ambient conditions without a quench step. Furthermore, we report on the improved stability and durability properties inherent to these films, which feature improved morphologies and optoelectronic properties compared to films spin-coated in a glovebox with antisolvent. We tune the amount of GG in the perovskite precursor and study the interplay between GG concentration and processability, morphological control, and increased stability under humidity, heat, and mechanical testing. The simplicity of this approach and insensitivity to environmental conditions enable a wide process window for the production of low-defect, mechanically robust, and operationally stable perovskites with fracture energies among the highest obtained for perovskites.
14 SOLAR ENERGY↗
Lamination of transparent conductive adhesives for tandem solar cell applications
A transparent conductive adhesive (TCA) interlayer for mechanically stacked multijunction solar cells provides adhesive strength and electrical connection between sub-cells when stacked. The fabrication of TCA sheets from an ethyl-vinyl acetate (EVA) matrix and silver coated compliant conductive microspheres, similar to industry-standard EVA encapsulant sheets, compatible with a standard lamination process was developed. Blade coating TCA sheets using 3D printed blades and testing of vertical conduction through the interlayer with a TCA conductivity jig allowed for reproducible measurements and low-cost fabrication. The supplemental information provides design files to enable other researchers to produce their own blades and testing jigs. We identified 0.5 mm as an optimal blade height for producing lab-scale TCA sheets and 120 °C at 3 psi for 10 min as the optimal vacuum lamination process to minimize resistance and possible damage to samples. For TCA sheets with coverages between 0.75% and 9%, the series resistance was approximately 0.2 O cm2 which should result in minimal losses for one-sun photovoltaic applications.
14 SOLAR ENERGY↗
Ultrahigh Performance Metallic Turbine Blades for Extreme Environments
In ULTIMATE Phase-I, The Boeing Company and Alloyed Inc. aimed to produce ultrahigh performance metallic extreme environment turbine blades with a base blade alloy capable of inert operation at 1300C, and a maximum coated blade operating temperature up to 1800C. High-performance structural designs for extreme service conditions place additional demands on the present material capability and can potentially outpace the current state-of-the-art in the alloy design space and metal processing. As a part of exploration and adoption of novel concepts for material maturation, the team explored a series of capable base novel refractory complex concentrated alloy (RCCA) compositions and potential powder enhancements. Advanced manufacturing processes, with a focus on laser powder bed fusion additive manufacturing (AM) and powder metallurgy (PM) approaches, were applied to consolidate new alloys and for near net shape processing of blades from the base RCCA.
Yousefiani, Ali↗
Ceramic thermal protective coating withstands hostile environment of rotating turbine blades
Ceramic coatings have low thermal conductivity. They provide potential for increased engine performance, reduced fuel consumption, use of less costly materials or construction procedures, and increased life and durability.
Liebert, C. H.↗
Manipulation and statistical analysis of the fluid flow of polymer semiconductor solutions during meniscus-guided coating
Recent work in structure–processing relationships of polymer semiconductors have demonstrated the versatility and control of thin-film microstructure offered by meniscusguided coating (MGC) techniques. Here, we analyze the qualitative and quantitative aspects of solution shearing, a model MGC method, using coating blades augmented with arrays of pillars. The pillars induce local regions of high strain rates—both shear and extensional—not otherwise possible with unmodified blades, and we use fluid mechanical simulations to model and study a variety of pillar spacings and densities. We then perform a statistical analysis of 130 simulation variables to find correlations with three dependent variables of interest: thin-film degree of crystallinity and transistor field-effect mobilities for charge-transport parallel (Μ para ) and perpendicular (Μ perp ) to the coating direction. Our study suggests that simple fluid mechanical models can reproduce substantive correlations between the induced fluid flow and important performance metrics, providing a methodology for optimizing blade design.
36 MATERIALS SCIENCE↗
Carbon Electrode with Sputtered Au Coating for Efficient and Stable Perovskite Solar Cells
Halide perovskite solar cells (PSCs) represent a low-cost and high-efficiency solar technology. However, most of the highly efficient PSCs need a noble electrode, such as Au, through thermal evaporation. Here it is reported that a sputtered Au electrode on a PSC could damage the organic hole transport layer (HTL) and the perovskite layer. Here, we report a simple, yet effective sputtered gold nanoparticle decorated carbon electrode to fabricate efficient and stable planar PSCs. The sputtered Au layer on the doctor-bladed coated carbon electrode can be directly applied to the perovskite semicells by mechanical stacking. By optimizing the gold thickness, a power conversion efficiency (PCE) of 16.87% was obtained for the composite electrode-based PSC, while the reference device recorded a PCE of 12.38%. The composite electrode-based device demonstrated 96% performance retention after being stored under humid conditions (50-60%) without encapsulation for ~100 h. This demonstrates a promising pathway toward the commercialization of large-scale manufacturable sputtered electrodes for the PSC solar module.
14 SOLAR ENERGY↗
Silver Nanowire-Indium Zinc Oxide Composite Flexible Transparent Conducting Electrodes Made by Spin- coating and Photonic Curing
Realizing high-throughput, low-cost perovskite solar cell (PSC) manufacturing is highly sought-after in photovoltaic (PV) research in recent years. To fully achieve roll-to-roll (R2R) manufacturing of PSCs, it is important to consider the flexible transparent electrode (TE). PET/ITO is a commonly used substrate for making flexible PSCs. When optimizing transparent conducting materials, there is a tradeoff between sheet resistance (Rsh) and optical transparency. Because commercial PET/ITO substrates are made with slow (~1 m/min) vacuum deposition processes, they tend to be expensive. Therefore, it would be advantageous to develop a high-throughput, R2R compatible, solution-deposition approach for fabricating the TE on PET substrates. While various solution-deposition processes, such as blade coating or slot-die coating, can achieve the desired web speed of > 10 m/min, there is still a need to improve the post-deposition annealing step. One promising post-deposition processing technique is intense-pulsed-light processing, also known as photonic curing. Photonic curing delivers short (0.01 – 100 ms) pulses of broadband (200 – 1500 nm) light from a xenon flash lamp to the samples. Any materials in the sample stack that absorb light will convert the impinging light pulse into heat within the sample, which drives changes in the sample (calcination, phase change, crystallization, etc.). Photonic curing has three main advantages over thermal annealing: 1. Faster processing speed (milliseconds or seconds). 2. Compatibility with plastic substrates. 3. Smaller physical footprint and less wasted energy. Since the light pulses are on for a short time, the intensity can be high while the total energy delivered to the sample is low, minimizing damages to the plastic substrates. In this work, a hybrid TE material is fabricated on PET substrates using photonic curing. The hybrid TE material contains a layer of silver nanowires (AgNWs) and a layer of metal-oxide (InOx, ITO, IZO, etc.). The AgNWs increase the light absorbed by the film during the photonic curing process, which leads to higher processing temperatures, possibly improving the conversion of the metal-oxide layer. The AgNWs also enhance the electrical conductivity of the final TE layer after photonic curing. A AgNW and metal-oxide bilayer is formed by spin coating each solution onto the PET substrate sequentially followed by a single photonic curing process. We use average optical transmittance (Tavg) from 400 to 700 nm and average Rsh to evaluate the TE performance. The following photonic curing parameters are varied to optimize Tavg (maximize) and Rsh (minimize): Pulse voltage, pulse envelope, number of micro-pulses, duty cycle, number of pulses, and pulse repetition rate. Preliminarily, we also observe a significant impact on the TE properties by the volume of AgNW deposited during the spin coating deposition step. Using dispense volumes of 80 µL and 20 µL, we achieve samples with Tavg = 73%, Rsh = 19 Ω/sq, and roughness = 9 nm, and Tavg = 83%, Rsh = 58 Ω/sq, and roughness = 5.6 nm, respectively, after photonic curing.
14 SOLAR ENERGY↗
Tunable Solid‐State Properties and Anisotropic Charge Mobility in Hydrogen‐Bonded Diketopyrrolopyrrole Polymers via Automated Device Fabrication and Characterization
The optoelectronic properties of semiconducting polymers and device performance rely on a delicate interplay of design and processing conditions. However, screening and optimizing the relationships between these parameters for reliably fabricating organic electronics can be an arduous task requiring significant time and resources. To overcome this challenge, Polybot is developed—a robotic platform within a self‐driving lab that can efficiently produce organic field‐effect transistors (OFETs) from various semiconducting polymers via high‐throughput blade coating deposition. Polybot not only handles the fabrication process but also can conduct characterization tests on the devices and autonomously analyze the data gathered, thus facilitating the rapid acquisition of data on a large scale. This work leverages the capabilities of this platform to investigate the fabrication of OFETs using hydrogen bonding‐containing semiconducting polymers. Through high‐throughput fabrication and characterization, various data trends are analyzed, and large extents of anisotropic charge mobility are observed in devices. The materials are thoroughly characterized to understand the role of processing conditions in solid state and electronic properties of these organic semiconductors. The findings demonstrate the effectiveness of automated fabrication and characterization platforms in uncovering novel structure–property relationships, facilitating refinement of rational chemical design, and processing conditions, ultimately leading to new semiconducting materials.
automated fabrication and characterization↗
Hybrid Data‐Driven Discovery of High‐Performance Silver Selenide‐Based Thermoelectric Composites
Optimizing material compositions often enhances thermoelectric performances. However, the large selection of possible base elements and dopants results in a vast composition design space that is too large to systematically search using solely domain knowledge. To address this challenge, a hybrid data-driven strategy that integrates Bayesian optimization (BO) and Gaussian process regression (GPR) is proposed to optimize the composition of five elements (Ag, Se, S, Cu, and Te) in AgSe-based thermoelectric materials. Data is collected from the literature to provide prior knowledge for the initial GPR model, which is updated by actively collected experimental data during the iteration between BO and experiments. Within seven iterations, the optimized AgSe-based materials prepared using a simple high-throughput ink mixing and blade coating method deliver a high power factor of 2100 µW m −1 K −2 , which is a 75% improvement from the baseline composite (nominal composition of Ag 2 Se 1 ). In conclusion, the success of this study provides opportunities to generalize the demonstrated active machine learning technique to accelerate the development and optimization of a wide range of material systems with reduced experimental trials.
36 MATERIALS SCIENCE↗
Optimized Incorporation of Furan into Diketopyrrolopyrrole-Based Conjugated Polymers for Organic Field-Effect Transistors
Flexible electronics have received considerable attention in the past decades due to their promising application in rollable display screens, wearable devices, implantable devices, and other electronic applications. Here, in particular, conjugated polymers are favored for flexible electronics due to their mechanical flexibility and potential for solution-processed fabrication techniques, such as blade-coating, roll-to-roll printing, and high-throughput printing allowing for high-performance transistor devices. Thiophene is the prevailing conjugated unit to construct these conjugated polymers due to its favorable electronic properties. On the other hand, furans are among the few conjugated moieties that are easily derived from bio renewable resources. To promote sustainability, we selectively introduced furan into the conjugated backbone of a high-mobility polymer scaffold and systematically studied the effect on the microstructure and charge transport. We show that partially and selectively replacing thiophene units with furan can yield nearly comparable performance compared to the all-thiophene polymer. This strategy offers an improvement in the sustainability of the polymer by incorporating bio-sourced furan without sacrificing the high-performance characteristics. Meanwhile, polymers with incorrect or complete furan incorporation show reduced mobilities. This work serves to develop coherent structure–morphology–performance relationships; such knowledge will establish guidelines for the future development of sustainable, furan-based conjugated materials.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
The Importance of Nonequilibrium to Equilibrium Transition Pathways for the Efficiency and Stability of Organic Solar Cells
Controlled morphology of solution-processed thin films have realized impressive achievements for non-fullerene acceptor (NFA)–based organic solar cells (OSCs). Given the large set of donor–acceptor pairs, employing various processing conditions to realize optimal morphology for high efficiency and stable OSCs is a strenuous task. Therefore, comprehensive correlations between processing conditions and morphology evolution pathways have to be developed for efficient performance and stability of devices. Within the framework of the blend system, crystallization transitions of NFA molecules are tracked utilizing the first heating scan of differential scanning calorimeter (DSC) measurement correlating with respective morphology evolution of blend films. Real-time dynamics measurements and morphology characterizations are combined to provide optimal morphology transition pathways as NFA molecules are shown to be released from the mixed phase to form balanced ordered packing with variant processing conditions. Polymer:NFA films are fabricated using blade coating incorporating solvent additive or thermal annealing as processing conditions as a correlation is formulated between performance and stability of solar cells with morphology transition pathways. In conclusion, this work demonstrates the significance of processing condition-controlled transition pathways for the realization of optimal morphology leading to superior OSC devices.
14 SOLAR ENERGY↗
Improved Organic Electrochemical Transistors via Directed Crystallizable Small Molecule Templating
Organic electrochemical transistors (OECTs) are of great interest as biosensors and for flexible electronics applications. Historically, processing techniques have been widely used to improve the performance of polymers in organic electronics but have been underutilized in the field of OECTs. Here, in this work, we study the effects of a crystallizable small molecule template for improving the performance of poly(3-hexylthiophene-2,5-diyl) (P3HT)-based OECTs. We utilize 1,3,5-trichlorobenzene (TCB) as a crystallizable additive to induce directional crystallization during blade coating. This procedure results in an aligned, highly ordered, and moderately porous layer of the semiconducting polymer. We find that compared to neat P3HT solutions, films cast with TCB additive show a greater than 8× improvement in the steady state figure of merit for OECTs. Additionally, the optimum TCB loading produces anisotropic OECTs where the polymer chain aligned parallel to the current outperforms the perpendicular alignment by more than a factor of 10. We investigated the mechanism of this improvement and found that polymer alignment, polymer ordering, and film porosity all play a role in improving the device performance. Overall, these results demonstrate the importance of processing on the optimization of polymers for OECTs and suggest a route to greatly improve the performance of commercially available hydrophobic polymers.
36 MATERIALS SCIENCE↗