Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “biogas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Improving Volatile Fatty Acid Productivity of Anaerobic Digestion

Typical anaerobic digestion (AD) focusses on complete conversion of waste to biogas (primarily carbon dioxide and methane). However, the intermediate metabolites of the AD process, which includes short- and long-chain volatile fatty acids (VFAs), that could serve as the precursors for useful industrial applications are typically ignored. The goal of this project is to eliminate production of biogas while enhancing the production of the intermediate VFAs. Using a mixed microbial consortium (from rumen sources and waste-water sludge), we have determined the optimal carbon loading (chemical oxygen demand, "COD") and optimal pH, that results in high VFA concentrations from food waste. The best VFA yields were obtained using 15 g COD/L and a pH of 9.0 for this substrate. pH 9 produced over 200% higher VFA titers than the controlled conditions (i.e., ph 7.0) after 35 d of digestion, in comparison to pH 5 that showed - 88% higher titers than the control digestion. As expected, the cumulative biogas production was highest in the pH 7.0 condition, in comparison to pH 5.0 or pH 9.0. We further observed that removal of VFAs using solid-liquid separation technique reduce the inhibitory effects of VFAs, thereby leading to overall improvement in conversion efficiency. 16s rRNA analysis is being carried out to explain and identify the biocatalysts that enable VFA production in these AD cultures. Additional efforts to improve VFA yields via increasing the total solid content, temperature optimizations, VFA removal via electrodialysis, and improving hydrolysis via microaeration will be presented.

anaerobic digestion↗
DOE OSTI2024

Minimizing grid energy consumption in wastewater treatment plants: Towards green energy solutions, water sustainability, and cleaner environment

Wastewater treatment plants (WWTPs) consume significant amount of energy to sustain their operation. From this point, the current study aims to enhance the capacity of these facilities to meet their energy needs by integrating renewable energy sources. The study focused on the investigation of two primary solar energy systems in As Samra WWTP in Jordan. The first system combines parabolic trough collectors (PTCs) with thermal energy storage (TES). This system primarily serves to fulfill the thermal energy demands of the plant by reducing the demands from boiler units, which allows more biogas for electricity generation. The second system is a photovoltaic (PV) system with Lithium-Ion batteries, which directly produces electricity that will be used to cover part of the electrical energy demands of plant. To assess the optimal configuration, two distinct scenarios have been formulated and compared to the current case scenario (SC#1). The first scenario focuses on maximizing the net present value (NPV) and minimizing the levelized cost of electricity (LCOE). The second scenario is centred on minimizing the levelized cost of heat (LCOH). The findings indicate that both scenarios succeeded in reducing the reliance on the grid to a value that reach 1 %. Moreover, they both reduced biogas percentage in energy production from 88 % to approximately 65 % through the integration of the PV system. In terms of thermal demand, SC#2 reduced the reliance on biogas boiler units from 100 % to 25 %, while SC#3 achieved an even more impressive reduction to just 8 %. The best LCOE value was attained in SC#2, at 0.0895 USD/kWh, with an NPV of 10.54 million USD. Conversely, SC# 3 yielded an LCOH value of 0.0432 USD/kWh th compared to 0.0534 USD/kWh th USD for SC#2. In conclusion, despite their relatively high capital and operating costs, SC#2 and SC#3 managed to substantially decrease the annual electricity expenditure from approximately 2 million USD to 86,000 USD and 0 USD, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Energy utilization strategies in lignocellulosic biorefineries

Lignocellulosic biorefineries can generate various energy-rich side streams, including biogas from anaerobic digestion, a lignin stream from biomass pretreatment, and conversion residues. This study evaluates different chemical energy utilization strategies in lignocellulosic biorefineries based on energy and carbon efficiencies, cost, and greenhouse gas mitigation potential. Specifically, using modeling and optimization, we examine strategies that include electricity generation, biogas upgrade to biomethane, lignin valorization, and carbon capture and storage. We find that upgrading biogas to biomethane demonstrates the highest energy efficiency and leads to the lowest minimum fuel selling price for the main product, ethanol. The biorefinery with carbon capture and storage achieves the lowest net carbon footprint. Lignin valorization has the highest carbon footprint due to the additional materials required for lignin depolymerization, despite its potential to produce high value bioproducts.

Aboagye, Emmanuel A. [Princeton Univ., NJ (United ↗
DOE OSTI2024

Enhancing anaerobic digestion of lignocellulosic biomass by mechanical cotreatment

Abstract Background The aim of this study was to increase the accessibility and accelerate the breakdown of lignocellulosic biomass to methane in an anaerobic fermentation system by mechanicalcotreatment: milling during fermentation, as an alternative to conventionalpretreatment prior to biological deconstruction. Effluent from a mesophilic anaerobic digester running with unpretreated senescent switchgrass as the predominant carbon source was collected and subjected to ball milling for 0.5, 2, 5 and 10 min. Following this, a batch fermentation test was conducted with this material in triplicate for an additional 18 days with unmilled effluent as the ‘status quo’ control. Results The results indicate 0.5 – 10 min of cotreatment increased sugar solubilization by 5– 13% when compared to the unmilled control, with greater solubilization correlated with increased milling duration. Biogas concentrations ranged from 44% to 55.5% methane with the balance carbon dioxide. The total biogas production was statistically higher than the unmilled control for all treatments with 2 or more minutes of milling (α = 0.1). Cotreatment also decreased mean particle size. Energy consumption measurements of a lab-scale mill indicate that longer durations of milling offer diminishing benefits with respect to additional methane production. Conclusions Cotreatment in anaerobic digestion systems, as demonstrated in this study, provides an alternative approach to conventional pretreatments to increase biogas production from lignocellulosic grassy material.

Biotechnology & Applied Microbiology↗
DOE OSTI2025

Reinventing wastewater treatment plants: energy neutral treatment and enhanced fertilizer production through a novel resource recovery center

Wastewater treatment plants (WWTPs) are typically energy intensive, mainly due to the secondary treatment processes such as activated sludge (AS) for treatment of organics as well as nutrients like nitrogen. Nitrogen removal presents a big problem for WWTPs. The main form of nitrogen in wastewater is ammonium, and an AS process uses oxygen to convert ammonium into nitrite and nitrate which is then converted to nitrogen through denitrification process. During anaerobic digestion (AD), organic nitrogen gets degraded, resulting in an effluent stream (centrate) with a high nitrogen content, mostly in the form of ammonium. This contributes 15-30% of total nitrogen to the wastewater influent which further increases energy consumption for aeration. The project aims to transform this conventional municipal WWTPs into energy-neutral, resource-recovering facilities by integrating three core technologies: • Cloth Media Filtration (CMF) to replace conventional primary sedimentation (CPS) and increase the diversion of organics from the energy intensive secondary treatment to AD. This results in reduced energy demand for aeration in the secondary process while simultaneously increasing the biogas production in the anaerobic digesters. • Anerobic Digester to increase biogas and ammonia production. • Membrane Evaporation (ME) to recover ammonia from AD centrate and produce marketable fertilizer. The benefits of proposed WWTP process modifications were evaluated using techno economic analysis (TEA) and life cycle assessment (LCA). For CMF portion of the research a statistical analysis was employed to develop data-driven tools that could be used to enhance and optimize its performance in terms of energy savings and effluent quality. The main objective of this project is to reduce the energy demand for secondary treatment at municipal WWTPs by at least 50%, increase anaerobic digester (AD) biogas and ammonia production by 100% and 120%, respectively, and recover 90% of ammonia from the AD. Integrated CMF, AD, and ME was shown to work synergistically toward achieving these decarbonization targets through energy-positive treatment and fertilizer recovery techniques.

42 ENGINEERING↗
DOE OSTI2025

Composite Sorbents: Enabling Economical Biomethane Production (CRADA Final Report)

The research performed under this CRADA enhanced the understanding of the performance of LLNL’s composite sorbent technology in the presence of raw biogas with H 2 S contamination, the long-term CO 2 removal performance stability of the composite sorbent in simulated biogas, and highlighted some of the challenges to overcome for further scale-up of material production and system design for deployment. Further development of the technology is of benefit to the public by enabling biogas upgrading from small sources for which existing commercial technologies are not suited, providing additional sources of renewable natural gas and diversifying our energy supply.

09 BIOMASS FUELS↗
DOE OSTI2022

Low temperature dry reforming of methane using Ru-Ni-Mg/ceria-zirconia catalysts: Effect of Ru loading and reduction temperature

Dry reforming catalysts, especially those with activity at moderate temperatures, have been intensely investigated to enhance the conversion of biogas. Here, Ru is evaluated as a promoter for Ni-Mg based catalysts. Catalysts based on 1.4 wt%Ni-1.0 wt%Mg-Ce 0.6 Zr 0.4 O 2 with Ru (0.02–0.32 wt%) were prepared using incipient wetness. The reducibility of the catalysts and conversions increased with increasing Ru content. Increases in conversions with increasing Ru loading was attributed to the additional active sites and synergistic effect between Ru and Ni, which weakened Ni-Mg interactions. Samples showed dry reforming activity at low temperatures (450–510 °C). Reaction rates and activation energies of higher loading Ru samples (1.4 wt%Ni-1.0 wt%Mg/Ce 0.6 Zr 0.4 O 2 with 0.16 and 0.32 wt%Ru) decreased when the reduction temperature was raised from 300 to 400 °C. A 20 h TOS study showed stable catalytic activity with minimal coke deposition. Furthermore, the results suggest that Ru is an alternative to Pt in promoting low temperature dry reforming of methane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Utilization of microalgae for agricultural runoff remediation and sustainable biofuel production through an integrated biorefinery approach

Generally wastewater such agricultural runoff is considered a nuisance; however, it could be harnessed as a potential source of nutrients like nitrates and phosphates in integrated biorefinery context. In the current study, microalgae Chlorella sp. S5 was used for bioremediation of agricultural runoff and the leftover algal biomass was used as a potential source for production of biofuels in an integrated biorefinery context. The microalgae Chlorella sp. S5 was cultivated on Blue Green (BG 11) medium and a comprehensive optimization of different parameters including phosphates, nitrates, and pH was carried out to acquire maximum algal biomass enriched with high lipids content. Dry biomass was quantified using the solvent extraction technique, while the identification of nitrates and phosphates in agricultural runoff was carried out using commercial kits. The algal extracted lipids (oils) were employed in enzymatic trans-esterification for biodiesel production using whole-cell biomass of Bacillus subtilis Q4 MZ841642. The resultant fatty acid methyl esters (FAMEs) were analyzed using Fourier transform infrared (FTIR) spectroscopy and gas chromatography coupled with mass spectrometry (GC–MS). Subsequently, both the intact algal biomass and its lipid-depleted algal biomass were used for biogas production within a batch anaerobic digestion setup. Interestingly, Chlorella sp. S5 demonstrated a substantial reduction of 95% in nitrate and 91% in phosphate from agricultural runoff. The biodiesel derived from algal biomass exhibited a noteworthy total FAME content of 98.2%, meeting the quality standards set by American Society for Testing and Materials (ASTM) and European union (EU) standards. Furthermore, the biomethane yields obtained from whole biomass and lipid-depleted biomass were 330.34 NmL/g VS added and 364.34 NmL/g VS added , respectively. In conclusion, the findings underscore the potent utility of Chlorella sp. S5 as a multi-faceted resource, proficiently employed in a sequential cascade for treating agricultural runoff, producing biodiesel, and generating biogas within the integrated biorefinery concept.

09 BIOMASS FUELS↗
DOE OSTI2024

Maximizing energy efficiency in wastewater treatment plants: A data-driven approach for waste heat recovery and an economic analysis using Organic Rankine Cycle and thermal energy storage

Maximizing energy efficiency through waste heat recovery (WHR) processes is crucial for sustainable and ecofriendly operations across multiple industries, notably in wastewater treatment plants (WWTPs). This work proposes a comprehensive approach for assessing the WHR feasibility in WWTPs, structured in two main objectives. Firstly, an Artificial Neural Network (ANN) model is developed to accurately predict WHR based on operational data, including biogas temperature, biogas pressure, daily production in kWh, and WHR values in kWh th . The second objective focuses on economically evaluating the WHR feasibility based on the estimated WHR values obtained by the ANN model, and then realistically assessing the economic feasibility of integrating the Organic Rankine Cycle (ORC) and Seasonal Thermal Energy Storage (STES) systems. With an application to the As-Samra WWTP located in Jordan, the developed ANN model demonstrates promising results in the validation phase, with a root mean square error (RMSE) of 2206 kWh/day, a mean absolute error (MAE) of 1674 kWh/day, and an R-squared (R 2 ) value of 68%. On the other hand, the economic analysis reveals that an optimal ORC system of 412.14 kW e capacity yields a Net Present Value (NPV) of 2.09 million US dollars, a Levelized Cost of Energy (LCOE) of 0.0749 USD/kWh, a Payback Period (PBP) of 4.8 years, and annual revenues of 428 kUSD. This work also investigates the techno-economic feasibility of integrating ORC-STES. Results indicate that the LCOE and PBP are highly affected by the ORC's capital cost, and integrating STES increases the LCOE to 0.0824 USD/kWh, rendering its integration with ORC infeasible. In conclusion, this study aims to advance the understanding and application of WHR in WWTPs, paving the way for more efficient and sustainable practices in the field.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Hydrogen production from full-strength corn stover fermentation effluent in single-chamber replaceable-cathode microbial electrolysis cells

Lignocellulosic residual biomass generated by the agricultural sector is an abundant feedstock for biohydrogen production via dark fermentation. However, this process is intrinsically inefficient, converting only ~30% of the reductant energy into H2 and leaving substantial amounts of reduced byproducts. These byproducts, mostly found in the fermentation effluents, can be further valorized in microbial electrolysis cells (MECs) to enhance the overall H2 recovery. However, current MEC configurations are typically dual- or single-chamber systems, yet both suffer from key inefficiencies. Dual-chamber systems rely on proton exchange membranes that are costly and prone to rapid biofouling, whereas single-chamber, membraneless systems are limited by reduced productivity due to H2 recycling and methanogenic consumption In this study, three single-chamber, 50-mL replaceable-cathode microbial electrolysis cells (RC-MECs) were 3D-printed and equipped with a physical separator to isolate anode and cathode compartments and limit H2 migration. Full-strength milled corn stover (MCS) fermentation effluent (COD of ~23.8 g-COD/L) was treated in fed-batch mode over two operational periods spanning 21 (Run 1) and 80 (Run 2) days. The RC-MECs exhibited comparable performance in both runs: after biofilm maturation, current densities exceeded 100 A/m²_cathode, COD removal reached up to 43%. Notably, extended RC-MECs operation led to a substantial methanogenic activity with the CH4 fraction in the cathode gas increasing to as high as 80% of the total biogas. Additions of a methanogenesis inhibitor 2-bromoethanesulfonate (2-BES) produced transient increases in hydrogen yields (11.51 and 5.12 L-H2/L_reactor/day in Runs 1 and 2, respectively); however, sustained 2-BES addition in subsequent cycles reduced total biogas production, decreased COD removal, and led to volatile fatty acid accumulation. Overall, single-chamber MECs can treat high-strength dark fermentation effluents while improving H2 recovery, but methanogenesis remains a key bottleneck, and complete long-term inhibition may be operationally unsustainable.

Hydrogen Production↗
DOE OSTI2023

Biological conversion of methane to methanol at high H 2 S concentrations with an H 2 S-tolerant methanotrophic consortium

To develop biological biogas to methanol conversion technology without costly hydrogen sulfide (H 2 S) removal, a high H 2 S tolerant methanotrophic consortium (HTMC), was enriched from an anaerobic digester effluent in presence of 5.64 g/m 3 H 2 S in the gas phase. The HTMC can grow stably and produce methanol under conditions with CH 4 /air mixtures containing 5.64 g/m 3 of H 2 S. There is no significant (p>0.05) difference in cell yield or CH 4 to methanol conversion efficiency between trials with different H 2 S concentrations from 0 g/m 3 to 5.64 g/m 3 . Further, under optimal conditions, a cell yield of 0.333 g cells/g CH 4 , a methanol concentration of 0.28 mg/mL, and a CH 4 to methanol conversion efficiency of 0.22 mol/mol were obtained, respectively. Besides methanotrophs (14.85%) and other bacteria, Cyanobacteria were also identified in the HTMC with a high abundancy (32.16%), which could broaden the application of HTMC for simultaneous utilization of CH 4 and CO 2 from raw biogas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Load-Shifting Strategies for Cost-Effective Emission Reductions at Wastewater Facilities

Significant hourly variation in the carbon intensity of electricity supplied to wastewater facilities introduces an opportunity to lower emissions by shifting the timing of their energy demand. This shift could be accomplished by storing wastewater, biogas from sludge digestion, or electricity from on-site biogas generation. However, the life cycle emissions and cost implications of these options are not clear. Here, we present a multiobjective optimization framework for comparing cost- and emission-minimizing load-shifting strategies at a California case study facility with a relatively low carbon intensity grid and high spread in peak and off-peak electricity prices. We evaluate cost and emission trade-offs from the optimal flexible operation of both existing infrastructure and optimally sized energy flexibility upgrades. We estimate energy-related emission reductions of up to 9.0% with flexible operation of existing infrastructure and up to 16.8% with optimally sized storage upgrades. Only a fraction of these potential savings are realized under actual industrial energy tariffs and the EPA’s recommended social cost of carbon. Energy flexibility may hold promise as a short-term emission-saving solution for the wastewater sector, but the extent of savings is heavily dependent on the cost of carbon, electricity tariffs, and emission intensity of the regional electricity grid.

climate↗
DOE OSTI2024

Phenotypic and genomic characterization of Methanothermobacter wolfeii strain BSEL, a CO 2 -capturing archaeon with minimal nutrient requirements

A new variant of Methanothermobacter wolfeii was isolated from an anaerobic digester using enrichment cultivation in anaerobic conditions. Here, the new isolate was taxonomically identified via 16S rRNA gene sequencing and tagged as M. wolfeii BSEL. The whole genome of the new variant was sequenced and de novo assembled. Genomic variations between the BSEL strain and the type strain were discovered, suggesting evolutionary adaptations of the BSEL strain that conferred advantages while growing under a low concentration of nutrients. M. wolfeii BSEL displayed the highest specific growth rate ever reported for the wolfeii species (0.27 ± 0.03 h –1 ) using carbon dioxide (CO 2 ) as unique carbon source and hydrogen (H 2 ) as electron donor. M. wolfeii BSEL grew at this rate in an environment with ammonium (NH 4 + ) as sole nitrogen source. The minerals content required to cultivate the BSEL strain was relatively low and resembled the ionic background of tap water without mineral supplements. Optimum growth rate for the new isolate was observed at 64°C and pH 8.3. In this work, it was shown that wastewater from a wastewater treatment facility can be used as a low-cost alternative medium to cultivate M. wolfeii BSEL. Continuous gas fermentation fed with a synthetic biogas mimic along with H 2 in a bubble column bioreactor using M. wolfeii BSEL as biocatalyst resulted in a CO 2 conversion efficiency of 97% and a final methane (CH 4 ) titer of 98.5%v, demonstrating the ability of the new strain for upgrading biogas to renewable natural gas.

09 BIOMASS FUELS↗
DOE OSTI2022

Irrigation Modernization Task 4: Accelerating Energy Solutions (FY2022 Final Report)

This report offers insights on energy solutions for irrigation modernization that serve the needs of farmers as well as residents and industry in the local community. Solutions are found in the irrigation districts where local generation from renewable energy sources – solar, hydro, and wind – can be combined with energy storage and customer loads. These combined resources configured in microgrids can lower costs during peak loads and provide resiliency by maintaining electricity supply during outages. The goal of this project, as stated in the FY2022 AOP, is to promote realization of energy solutions that are tailored to physical location, community, infrastructure, and energy value streams. Further, it is to develop examples of how to increase value of, and overcome barriers to, energy solutions in the context of irrigation modernization. In pursuit of that goal, the project looked at options for: 1) Reducing the cost of energy consumed in irrigation systems, 2) Increasing the revenue from surplus power generation, and 3) Deploying new power generation configured as part of a local microgrid. Potential solutions to reducing energy costs and increasing surplus power revenue revolve around addressing regulatory and legal constraints tied to how power is purchased by and sold to the irrigator or irrigation district. Some headway was made in identifying barriers and ways to push utilities to be more accommodating to distributed energy sources; however, for the most part, real progress hinges on changes at the regulatory and legislative level. Deployment of local, renewable generation systems can be implemented provided the economics of the project and the location are favorable. In concert with Famers Conservation Alliance and Energy Trust of Oregon, a number of approaches were studied in the past year, including off-grid solar powered pumps, grid-tied community solar projects, and in-conduit canal hydropower systems. Ultimately three viable projects were identified: 1) North Unit Irrigation District/City of Redmond, Oregon Critical Facility Microgrid – offers combined in-conduit hydro and solar power generation. 2) Wallowa County/Joseph, Oregon Irrigation System Upgrades – centered on upgrades to a non-powered dam that will add a turbine as well as in-conduit power in canal feeders downstream. 3) Medford, Oregon Wastewater Treatment Plant Biogas Cogeneration System – centered on building out biogas storage and grid upgrades to power the plant, sell excess power, and provide emergency backup power (supplanting a diesel generator). Each of these projects has characteristics that broaden the understanding of the value of microgrids employing renewable energy to achieve resiliency and net-zero carbon goals. The first two projects are centered on new hydropower systems. Although the Medford project is only tangentially tied to an irrigation district, it was selected for study analysis as it was the only one mature enough (with sufficient data) to complete an analysis within this project year. Thus, we chose to move forward developing a case study, in concert with the Community Water-Power Resilience project, to demonstrate a method for evaluating such projects. Essentially, this case study serves as a template for studies to be carried out next year that more directly involve irrigation system hydropower, e.g., the project at the Wallowa County/Joseph, Oregon Irrigation System. Lastly, it is recognized that the locations and case studies in this report are all located in Oregon. We recognize this as a limitation. While the intent is not to ignore other states or regions, this result is driven by the fact that we have cultivated a collaboration with non-profit entities in Oregon that focus on these topics – Farmers Conservation Alliance and Energy Trust of Oregon. These partners were central to identifying projects that may be good fits for this program. A goal in the coming year is to establish collaboration with entities in other states/regions that, similarly, can connect us to potential projects in their geographic area. The potential benefits from the WPTO’s support for demonstration projects as energy solutions in irrigation districts include: (1) Alternative power supplies for communities and farms using renewable, carbon-free energy resources, (2) Cost savings for electricity for communities and farms, (3) Resiliency of power supplies for critical loads when electricity from the grid is not available, (4) Resiliency of power supplies for critical infrastructure in the event of catastrophic events, and (5) Demonstration of irrigation modernization projects that provide resilience and a reduced carbon footprint to irrigation districts and nearby communities. These deployments can serve as vanguards/archetypes spurring similar projects in other districts and states.

13 HYDRO ENERGY↗
DOE OSTI2026

NREL's 1MW Water Electrolysis Stack Performance Validation to Pilot-Scale Renewable Natural Gas Production [Slides]

NREL has designed, built, and operates a 1MW water electrolyzer balance-of-plant to support industrial partners and the U.S. Department of Energy in developing next-generation PEM stacks to reduce the cost of hydrogen production. With that hydrogen, we are developing, innovating and de-risking a biomethanation process capable of megawatt-scale deployment that upgrades biogas waste streams to produce pipeline quality renewable natural gas (RNG). Biomethanation is a two-step process using a methanogenic microorganism to convert renewable hydrogen (H 2 ) and waste carbon dioxide (CO 2 ) to renewable methane (CH 4 ) - the primary component in natural gas. Using biogenic CO 2 from biogas sources like dairies, wastewater treatment plants, and landfills allows production of this drop-in direct replacement fuel. Research projects and future R&D topics are also discussed during the presentation.

08 HYDROGEN↗
NASA NTRS2001

Turning Gas into Greens

Scientists from Cook College, Rutgers University, and Stevens Institute of Technology conducted studies to create an experimental greenhouse that uses methane from decomposing trash to fuel a system that makes food. Biogasses created by the anaerobically decomposing trash are necessary to fulfill the energy needs of this revolutionary greenhouse. The primary emission, methane, is piped to the greenhouse boiler and used to fuel the hot water heating system. Thus far, the use of biogas has drastically reduced the operating costs of the greenhouse, eliminating the need for non-renewable fuels. The biogas will also generate electricity for the greenhouse in the near future. The plants are irrigated with recycled plant nutrients such as nitrogen, phosphorus, potassium, calcium, and magnesium. These nutrients are delivered through hydroponics, the cultivation of plants in a nutrient solution rather than in soil. High-pressure sodium lamps augment the natural light, thereby boosting production and reducing cropping time. A total of 16 hours of light are provided to the crop each day, year-round. It only takes about 90 days for a seed to germinate and produce a tomato harvest. Not only is the food produced faster, the manual labor needed for the upkeep of the plants is also drastically reduced.

Source record↗
DOE OSTI2025

Techno-economic analysis and life cycle analysis of renewable natural gas production from brewery wastewater via ex-situ methanation processes

As sustainability becomes increasingly critical, the brewing industry encounters challenges in managing high-organic-content wastewater, a promising renewable energy source. This study evaluates the economic feasibility and environmental impacts of converting brewery wastewater into renewable natural gas (RNG) through anaerobic digestion and biogas upgrading, with an emphasis on different hydrogen sources for biomethanation. Four scenarios were analyzed: Scenario 1 uses purchased hydrogen, while Scenarios 2–4 use renewable hydrogen from microbial electrolysis cells and water electrolyzers. Results show that capital investments for processing 139 MT/h of wastewater, yielding 208 m 3 /h of RNG, range from 10.6 M to 31.9M USD, with estimated minimum selling prices of RNG between 2.25 and 4.37 USD/m 3 . Life cycle greenhouse gas (GHG) emissions span from -21 to 32g CO 2 -equivalent per MJ of RNG. Further, this study presents key economic and environmental metrics for RNG production from brewery wastewater, offering insights to enhance sustainability in brewery wastewater management.

03 NATURAL GAS↗
DOE OSTI2024

Prioritization of Early-Stage Research and Development of a Hydrogel-Encapsulated Anaerobic Technology for Distributed Treatment of High Strength Organic Wastewater

This study aims to support the prioritization of research and development (R&D) pathways of an anaerobic technology leveraging hydrogel-encapsulated biomass to treat high-strength organic industrial wastewaters, enabling decentralized energy recovery and treatment to reduce organic loading on centralized treatment facilities. To characterize the sustainability implications of early-stage design decisions and to delineate R&D targets, an encapsulated anaerobic process model was developed and coupled with design algorithms for integrated process simulation, techno-economic analysis, and life cycle assessment under uncertainty. Across the design space, a single-stage configuration with passive biogas collection was found to have the greatest potential for financial viability and the lowest life cycle carbon emission. Through robust uncertainty and sensitivity analyses, we found technology performance was driven by a handful of design and technological factors despite uncertainty surrounding many others. Hydraulic retention time and encapsulant volume were identified as the most impactful design decisions for the levelized cost and carbon intensity of chemical oxygen demand (COD) removal. Encapsulant longevity, a technological parameter, was the dominant driver of system sustainability and thus a clear R&D priority. Ultimately, we found encapsulated anaerobic systems with optimized fluidized bed design have significant potential to provide affordable, carbon-negative, and distributed COD removal from high strength organic wastewaters if encapsulant longevity can be maintained at 5 years or above.

Anaerobic Treatment↗