Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wire arc additive manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE-20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ̊C.This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Lightweight High Pressure Die Casting Tooling

Oak Ridge National Laboratory (ORNL) and Mercury Marine partnered to develop and test methods for additively manufactured tooling for aluminum die casting applications under CRADA agreement NFE- 20-08193. Tooling is the largest capital expense for high production casting projects. The lead time for tooling is often measured in months with a typical project taking 9-12 months to realize Production Part Approval Process (PPAP) ready die cast samples. This project demonstrated the technical viability of rapidly produced steel components for high pressure die casting tooling via Wire Arc Additive Manufacturing (WAAM). A 410 stainless steel tool was redesigned and optimized with conformal cooling channels and additively manufactured. The finished tool was tested and used to produce over 4000 parts, which well surpassed expectations. A secondary objective was to evaluate the durability of multi-material additively manufactured (AM) components with conformal cooling. A large multi-material tool (H13 and 410SSNiMo) was manufactured using the same methods showing potential reductions in used material and cost. However, the H13 section sustained material cracking. Further analysis showed that the potential cause was the CTE mismatch of the two materials at higher temperatures. It is also suggested that the material mix can be used if the steel processing temperature does not exceed 600 ˚C. This project has shown high potential for using the WAAM technology for creating AM parts for aluminum dies casting. However, the multi-material approach requires extended study and tests.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Multi-material Parts Using H-13 Tool Steel

H-13 tools steel’s relative hardness, resistance to thermal fatigue, and high tolerance of thermal shock, make it very desirable for use in forging, pressing, casting, and extrusion processes[1]. H-13 is however typically quite expensive when compared to many other steel compositions. It is therefore desirable to encase a lower cost steel composition with H-13. This configuration allows for the benefits of H-13 tooling to be realized, at a considerably reduced cost. To demonstrate the viability of this concept, a casting tool was fabricated using a Wire Arc Additive Manufacturing (WAAM) process. Initial materials testing was conducted on a multi-material wall which consisted of one section of H-13 tool steel, and one section of 410NiNmo. These tests included scanning electron microscopy, energy dispersive X-ray spectroscopy, and hardness testing. This testing generated favorable results and subsequently a casting tool was fabricated for evaluation. Utilization of a Multi-Material WAAM process to fabricate large tooling in this manner could yield significant improvements in material cost, manufacturing agility, and supply chain complexity.

Lambert, Nathan [ORNL] (ORCID:0009000324134206)↗
DOE OSTI2022

Analysis of Conduction Cooling Strategies for Wire Arc Additive Manufacturing

Metal additive manufacturing (AM) processing consists of numerous parameters which take time to optimize for various geometries. One aspect of the metal AM process that continues to be explored is the control of thermal energy accumulation during component manufacturing due to the melting and solidification of the feedstock. Excessive energy accumulation causes thermal failure of the component while minimal energy accumulation causes lack of fusion with the build plate or previous layer. The ability to simulate the thermal response of an AM component can increase research efficiency by reducing the time to optimize thermal energy accumulation. This paper presents an effective implementation of finite element analysis to determine the thermal response of a wire arc additive manufactured component with various build plate sizes and cooling methods including, integral build plate cooling, oversized build plates with passive cooling, and non-integral build plate cooling. The use of integral build plate cooling channels was shown to decrease the interpass temperature at the conclusion of the build process by 55% and build plate temperature by 96% compared to the conventionally deposited sample with 20 second dwell time. The use of a tall build plate with passive cooling was shown to reduce the interpass temperature by 32% as compared to the conventionally deposited sample with 20 second dwell time. Each cooling strategy evaluated decreased the interpass temperature within a range of 20–55% which enables higher deposition rates and decreased dwell times during depositions. The cooling strategies are designed to be implemented in a hybrid or retrofit AM platform to mitigate concerns of the thermal input from the additive process having detrimental effects on the precision of the machining process. This paper shows that accurate simulations of all strategies can be used to accurately predict the thermal response of the various strategies discussed. These cooling strategies will allow for increased deposition rates with comparable interpass temperature and decreased dwell time, increasing deposition efficiency. This model and these simulations are verified by experimental results. It is concluded that passive strategies, such as the over-sized tall build plate, can be used when liquid coolant in the AM environment could negatively affect the deposition process. Active cooling strategies, such as the integral build plate cooling could be used if low thermal conductivity materials are deposited or higher material deposition rates are desired. This paper discusses the use of active and passive cooling used during AM and shows how a simulation model can be used to make design choices for cooling strategies. The model also enables verification of select critical process parameters such as dwell times for a desired interpass temperature.

Heinrich, Lauren↗
DOE OSTI2025

Characterization and prediction of the electromechanical wear of contact tips during wire arc additive manufacturing of 316L stainless steel

Here, this study seeks to better understand the degradation of the contact tip with respect to WAAM for a 316L wire electrode as well as explore methods of monitoring the contact tip state from process data. The contact tip, a consumable component, positions the wire and serves as the electrical contact surface between the wire electrode and the welding power supply. The wear of the contact tip was characterized in terms of material loss and material contamination for a set of tips worn to discrete levels as measured by the amount of wire fed or arc time. Geometrical characterization found a 49% increase in the bore exit area at 180 meters of wire fed. Machine learning models were developed to predict the relative bore exit area of the contact tip from arc-based process data and a random forest classifier exhibited favorable performance with a cross-validated f1-score of 0.84. The regression architecture implemented a multi-layer perceptron with the ability to predict the relative exit area with an $R^2$ score of 0.75. Key features used in the prediction include the standard deviation of the voltage and the time between shorts.

Contact tip wear↗
DOE OSTI2022

Effect of N 2 - and CO 2 -containing shielding gases on composition modification and carbonitride precipitation in wire arc additive manufactured grade 91 steel

Additive manufacturing (AM) represents a promising technique to fabricate metallic alloys with greater control of the resulting material features as compared to traditional manufacturing routes. Recently, there is greater interest in AM research on 9 wt% Cr ferritic/martensitic (F/M) steels, which are commonly studied for use in the nuclear energy industry. This work aims to prove that wire arc AM can manufacture F/M steels with adequate mechanical properties in multiple processing atmospheres and aims to study how shielding gas composition can be leveraged during fabrication to induce specific precipitation pathways. The effect of shielding gas composition on MX (M=Nb and/or V, Xdouble bondC and/or N) carbonitride precipitation in a 9 wt% Cr ferritic/martensitic (F/M) steel alloy known as Grade 91 was studied using N 2 and CO 2 gas additions to an inert Ar shielding gas atmosphere during wire arc AM. The N and C atoms present in the processing atmospheres were absorbed into the melt pools during fabrication. Due to their differing affinities for precipitate-forming reactions, the varying levels of C and N between the samples contributed to differences in final carbonitride composition and morphologies. Such precipitate behavior is of interest as carbonitrides have been shown to contribute to increased mechanical performance. This increased performance was studied via electron microscopy and tested for strength, ductility, and fracture properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi material/functionally graded wire arc additive manufacturing of high strength steel valves clad with nickel alloy 625 used for oil extraction

This Phase 1 technical collaboration project (ORNL/TM-2022/2683) began on August 1st, 2020 and concluded on July 31st, 2022. The collaboration partner Schlumberger is a large business enterprise assisting oil companies to extract oil from land and subsea cost competitively and safely. It is based in Houston, Texas USA. In this work as study of additive deposition of AWS EF100S-G and AWS ERNiCrMo-3 wires via wire-arc process was conducted.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Wire-arc Additive Manufacturing Benchmark

This is the dataset associated with the 2022 SRP Additive Manufacturing Prediction Challenge, originally hosted on Github at https://github.com/SRP-AM/SRP_AM_Prediction_Challenge. The benchmark was designed for validating prediction for the temperature history, residual stress, and distortion of an additively manufactured metal part with relatively simple geometry. A calibration problem with the same as-built geometry is provided with measured quantities of interest; including temperature histories at selective locations, post-build residual stress at selective locations, and overall distortion measurements. The challenge problem is presented with a different build sequence (i.e. thermal history). In this dataset, we include the actual recorded calibration and challenge measurements, as well as benchmark template files for testing predictions without incorporating the challenge data. Supplementary files around the materials and setup are available for transparency and reproducibility.

Bachus, Nicholas [UC Davis, Davis, CA]↗