Results for “Wetting” — Page 3

DOE OSTI2025

High resolution variability in wet deposition in the southeastern United States

Rainwater chemistry is determined by atmospheric pollutants and particles which vary spatially and temporally. Industrial and agricultural activities and meteorological events (e.g. sea breezes, severe weather, blowing dust) alter atmospheric particle and trace gas compositions. These gases and particles are scavenged by cloud and rain droplets that drive wet deposition. During an Intensive Operation Period (IOP) from April to October 2021, rainwater was collected at higher frequency intervals, usually daily, after precipitation events at three locations on the Savannah River Site (SRS). The farthest locations were separated by approximately 20 km. The mean concentration (μeq/L) of seven ions followed the Cl⁻ > SO 4 2− > Na⁺ > NO 3 ⁻ > K⁺ > Mg 2+ > Ca 2+ downward trend. Ion concentrations were compared to background ion concentrations from the National Atmospheric Deposition Program (NADP). The high frequency monthly averaged SRS data compared well with the monthly averaged NADP background but demonstrated extensive variability. In some months in 2021, the high frequency data compared better to the NADP site near the coast while in other months inland sites compared better. Strong spatial variability for ion concentrations was observed across SRS which was attributed to localized impacts in rainfall spatial variability. High frequency measurements allowed for comparison to regional weather patterns indicating influences from the Atlantic Ocean, Gulf of Mexico, and cities. This can account for spatial variability in the wet deposition flux. Sea breezes, Saharan dust, and anthropogenic sources were shown to impact wet deposition flux variability. Higher frequency precipitation chemistry sampling at numerous locations better captures ion concentration variability and improves measurement representativeness.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Physics of laser direct-drive liquid deuterium–tritium wetted foam capsules for inertial confinement fusion

Laser direct-drive liquid deuterium–tritium (DT) wetted foam capsules hold substantial promise for future advancements in inertial confinement fusion (ICF). For this new class of ICF capsules, additive manufacturing (AM) techniques are used to create low aspect ratio spherical shells of a low-density, foam-like CH lattice, which is wetted with cryogenic liquid DT. In the present paper, we discuss key physics issues intrinsic to ignition and burn propagation in laser direct drive wetted foam capsules. These include requirements on laser energy and power, implosion velocity, fuel adiabat, and initial density and dimensions of the CH lattice shell.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2015

Random Vibration Testing of Advanced Wet Tantalum Capacitors

Advanced wet tantalum capacitors allow for improved performance of power supply systems along with substantial reduction of size and weight of the systems that is especially beneficial for space electronics. Due to launch-related stresses, acceptance testing of all space systems includes random vibration test (RVT). However, many types of advanced wet tantalum capacitors cannot pass consistently RVT at conditions specified in MIL-PRF-39006, which impedes their use in space projects. This requires a closer look at the existing requirements, modes and mechanisms of failures, specifics of test conditions, and acceptance criteria. In this work, different lots of advanced wet tantalum capacitors from four manufacturers have been tested at step stress random vibration conditions while their currents were monitored before, during, and after the testing. It has been shown that the robustness of the parts and their reliability are mostly due to effective self-healing processes and limited current spiking or minor scintillations caused by RVT do not increase the risk of failures during operation. A simple model for scintillations events has been used to simulate current spiking during RVT and optimize test conditions. The significance of scintillations and possible effects of gas generation have been discussed and test acceptance criteria for limited current spiking have been suggested.

cracking↗

NASA NTRS2015

Random Vibration Testing of Advanced Wet Tantalum Capacitors

Advanced wet tantalum capacitors allow for improved performance of power supply systems along with substantial reduction of size and weight of the systems that is especially beneficial for space electronics. Due to launch-related stresses, acceptance testing of all space systems includes random vibration test (RVT). However, many types of advanced wet tantalum capacitors cannot pass consistently RVT at conditions specified in MIL-PRF-39006, which impedes their use in space projects. This requires a closer look at the existing requirements, modes and mechanisms of failures, specifics of test conditions, and acceptance criteria. In this work, different lots of advanced wet tantalum capacitors from four manufacturers have been tested at step stress random vibration conditions while their currents were monitored before, during, and after the testing. It has been shown that the robustness of the parts and their reliability are mostly due to effective self-healing processes and limited current spiking or minor scintillations caused by RVT do not increase the risk of failures during operation. A simple model for scintillations events has been used to simulate current spiking during RVT and optimize test conditions. The significance of scintillations and possible effects of gas generation have been discussed and test acceptance criteria for limited current spiking have been suggested.

cracking↗

NASA NTRS2015

Random Vibration Testing of Advanced Wet Tantalum Capacitors

Advanced wet tantalum capacitors allow for improved performance of power supply systems along with substantial reduction of size and weight of the systems that is especially beneficial for space electronics. Due to launch-related stresses, acceptance testing of all space systems includes random vibration test (RVT). However, many types of advanced wet tantalum capacitors cannot pass consistently RVT at conditions specified in MIL-PRF-39006, which impedes their use in space projects. This requires a closer look at the existing requirements, modes and mechanisms of failures, specifics of test conditions, and acceptance criteria. In this work, different lots of advanced wet tantalum capacitors from four manufacturers have been tested at step stress random vibration conditions while their currents were monitored before, during, and after the testing. It has been shown that the robustness of the parts and their reliability are mostly due to effective self-healing processes and limited current spiking or minor scintillations caused by RVT do not increase the risk of failures during operation. A simple model for scintillations events has been used to simulate current spiking during RVT and optimize test conditions. The significance of scintillations and possible effects of gas generation have been discussed and test acceptance criteria for limited current spiking have been suggested.

wet tantalum capacitors↗

NASA NTRS2015

Leakage Currents and Gas Generation in Advanced Wet Tantalum Capacitors

Currently, military grade, established reliability wet tantalum capacitors are among the most reliable parts used for space applications. This has been achieved over the years by extensive testing and improvements in design and materials. However, a rapid insertion of new types of advanced, high volumetric efficiency capacitors in space systems without proper testing and analysis of degradation mechanisms might increase risks of failures. The specifics of leakage currents in wet electrolytic capacitors is that the conduction process is associated with electrolysis of electrolyte and gas generation resulting in building up of internal gas pressure in the parts. The risk associated with excessive leakage currents and increased pressure is greater for high value advanced wet tantalum capacitors, but it has not been properly evaluated yet. In this work, in Part I, leakages currents in various types of tantalum capacitors have been analyzed in a wide range of voltages, temperatures, and time under bias. Gas generation and the level of internal pressure have been calculated in Part II for different case sizes and different hermeticity leak rates to assess maximal allowable leakage currents. Effects related to electrolyte penetration to the glass seal area have been studied and the possibility of failures analyzed in Part III. Recommendations for screening and qualification to reduce risks of failures have been suggested.

degradation mechanisms↗

NASA NTRS2021

Technical Note: AQMEII4 Activity 1: Evaluation of Wet and Dry Deposition Schemes as an Integral Part of Regional-scale Air Quality Models

We present in this technical note the research protocol for phase 4 of the Air Quality Model Evaluation International Initiative (AQMEII4). This research initiative is divided into two activities, collectively having three goals: (i) to define the current state of the science with respect to representations of wet and especially dry deposition in regional models, (ii) to quantify the extent to which different dry deposition parameterizations influence retrospective air pollutant concentration and flux predictions, and (iii) to identify, through the use of a common set of detailed diagnostics, sensitivity simulations, model evaluation, and reduction of input uncertainty, the specific causes for the current range of these predictions. Activity 1 is dedicated to the diagnostic evaluation of wet and dry deposition processes in regional air quality models (described in this paper), and Activity 2 to the evaluation of dry deposition point models against ozone flux measurements at multiple towers with multiyear observations (to be described in future submissions as part of the special issue on AQMEII4). The scope of this paper is to present the scientific protocols for Activity 1, as well as to summarize the technical information associated with the different dry deposition approaches used by the participating research groups of AQMEII4. In addition to describing all common aspects and data used for this multi-model evaluation activity, most importantly, we present the strategy devised to allow a common process-level comparison of dry deposition obtained from models using sometimes very different dry deposition schemes. The strategy is based on adding detailed diagnostics to the algorithms used in the dry deposition modules of existing regional air quality models, in particular archiving diagnostics specific to land use–land cover (LULC) and creating standardized LULC categories to facilitate cross-comparison of LULC-specific dry deposition parameters and processes, as well as archiving effective conductance and effective flux as means for comparing the relative influence of different pathways towards the net or total dry deposition. This new approach, along with an analysis of precipitation and wet deposition fields, will provide an unprecedented process-oriented comparison of deposition in regional air quality models. Examples of how specific dry deposition schemes used in participating models have been reduced to the common set of comparable diagnostics defined for AQMEII4 are also presented.

Air Quality Model Evaluation International Initiat↗

DOE OSTI2025

Simulation insights into wetting properties of hydrogen-brine-clay for hydrogen geo-storage

Hydrogen geo-storage is attracting substantial interdisciplinary interest as a cost-effective and sustainable option for medium- and long-term storage. Hydrogen can be stored underground in diverse formations, including aquifers, salt caverns, and depleted oil and gas reservoirs. The wetting dynamics of the hydrogen-brine-rock system are critical for assessing both structural and residual storage capacities, and ensuring containment safety. Through molecular dynamics simulations, we explore how varying concentrations of cushion gases (CO 2 or CH 4 ) influence the wetting properties of hydrogen-brine-clay systems under geological conditions (15 MPa and 333 K). We employed models of talc and the hydroxylated basal face of kaolinite (kaoOH) as clay substrates. Our findings reveal that the effect of cushion gases on hydrogen-brine-clay wettability is strongly dependent on the clay-brine interactions. Notably, CO 2 and CH 4 reduce the water wettability of talc in hydrogen-brine-talc systems, while exerting no influence on the wettability of hydrogen-brine-kaoOH systems. Detailed analysis of free energy of cavity formation near clay surfaces, clay-brine interfacial tensions, and the Willard-Chandler surface for gas-brine interfaces elucidate the molecular mechanisms underlying wettability changes. Our simulations identify empirical correlations between wetting properties and the average free energy required to perturb a flat interface when clay-brine interactions are less dominant. Here, our thorough thermodynamic analysis of rock-fluid and fluid-fluid interactions, aligning with key experimental observations, underscores the utility of simulated interfacial properties in refining contact angle measurements and predicting experimentally relevant properties. These insights significantly enhance the assessment of gas geo-storage potential. Prospectively, the approaches and findings obtained from this study could form a basis for more advanced multiscale simulations that consider a range of geological and operational variables, potentially guiding the development and improvement of geo-storage systems in general, with a particular focus on hydrogen storage.

25 ENERGY STORAGE↗

DOE OSTI2026

Molecular Dynamics Investigation of Oil Wetting on Synthetic Polymer Substrates

Understanding the interaction of polymer surfaces with nonpolar, low surface tension liquids, or whether a substrate is oleophobic versus oleophilic, is critical for applications ranging from antifingerprint coatings to oil–water separation membranes and oil spill remediation. Despite its technological importance, the molecular mechanisms underpinning polymer–oil wetting are not well characterized. Here, we employ molecular dynamics simulations to investigate the behavior of n-hexadecane in contact with chemically distinct polymer surfaces, spanning eight constitutional unit chemistries as well as amorphous and crystalline morphologies. This permits a critical examination of both thermodynamic and dynamic descriptors of oleophobicity, including oil contact angle, dewetting free energy, interfacial diffusivity, and a proposed “ghost probe energy,” which does not require explicit simulation of oil–polymer interactions. We find that the oil contact angle does not reliably distinguish oleophobic behavior across polymer chemistries, whereas other metrics provide clearer and more consistent differentiation. Analysis of the results reveals that polymer–oil wetting behavior is primarily governed by interfacial van der Waals interactions and modulated by surface flexibility and morphology. Collectively, this work establishes a computational framework for characterizing oil wetting and provides additional insight into what molecular-level factors dictate trends in oleophobicity.

lipids↗

DOE OSTI2024

Caprock Remains Water Wet Under Geologic CO 2 Storage Conditions

Abstract Carbon storage technology is primarily targeted in saline formations, which is a porous rock matrix filled with brine, sealed with a low permeability caprock. There are significant variations of CO 2 wetting properties, typically reported in the literature as contact angle of CO 2 and brine interacting with a rock material, suggesting that CO 2 could become wetting under geostorage conditions and negatively impact containment effectiveness. Here, we performed the first controlled laboratory measurements of CO 2 ‐brine contact angles on shale rocks from low permeability sealing formations with distinctive mineralogic properties—calcite‐rich, quartz‐rich, and dolomite‐rich. We targeted temperatures at 40° and 100°C, pressures at 8.3, 34.5, and 62.1 MPa, and salinity at 35,000 and 260,000 ppm. Results show no significant change in contact angle with mineralogy, temperature, pressure, salinity, and CO 2 bubble size. We conclude that caprocks will remain water‐wet at geologic CO 2 storage conditions and will not lose their capillary sealing capacity.

Tapriyal, Deepak↗

DOE OSTI2026

Wet-Bulb Temperature from Pressure, Relative Humidity, and Air Temperature

Abstract The algorithms currently in use for calculating the wet-bulb temperature from pressure, relative humidity, and air temperature have errors of a degree or more. Here, the equation for the thermodynamic wet-bulb temperature is derived using the Rankine–Kirchhoff approximations, which are highly accurate for meteorological and climatological applications. Likewise, equations are derived for the thermodynamic ice-bulb temperature and for the psychrometric wet-bulb and ice-bulb temperatures. The equations are fast to solve, requiring only a microsecond on a current laptop computer, and the results match empirical data to within hundredths of a degree. Furthermore, the equations reveal the existence of air temperatures and humidities that generate bistability: Evaporating liquid water is stable at a liquid temperature above freezing and, simultaneously, sublimating ice is stable at an ice temperature below freezing.

Romps, David M↗

DOE OSTI2026

Robust and High Throughput Tools for Characterization of Wet Cellulosic Biogas Feedstocks and Co-Products: Cooperative Research and Development Final Report, CRADA Number CRD-21-21472

This project will develop standardized analytical procedures to support understanding of the chemical composition of wet manure feedstocks, and the digestate formed following anaerobic digestion of organic waste to produce renewable natural gas (RNG). The developed methods will be validated to improve component mass closure, eliminate ambiguities around key constituents, and document the precision and accuracy of the methods. Following validation of the analytical laboratory methods for characterization of wet organic waste feedstocks and digestate, NLR will use the same samples to build and validate near-infrared (NIR) models for high throughput analysis, potentially deployable at commercial facilities, enabling increased production of low carbon intensity RNG from wet organic wastes.

09 BIOMASS FUELS↗

NASA NTRS1980

Permittivity and attenuation of wet snow between 4 and 12 GHz

The permittivity and attenuation of prepared samples of wet snow are measured and curves presented showing the dependence of these quantities of snow wetness and frequency. Equations are given that express the experimentally determined relation between attenuation per unit length and volume-percent wetness at any frequency between 4 and 12 GHz. Additional equations are given for the calculation of permittivity from the snow density, attenuation per unit length, and frequency. Water retention characteristics of snow are described. Some applications of the techniques, such as runoff forecasting from mountain snowpacks, are proposed.

Linlor, W. I.↗

NASA NTRS1982

The Seasat altimeter wet tropospheric range correction

It is found that the difference between the wet tropospheric corrections obtained with the Seasat Multichannel Microwave Radiometer (SMMR) algorithm and corrections based on near-coincident radiosonde meteorological measurements has a standard deviation of 2.79 cm, which is consistent with the independent value for water vapor determination accuracy reported by the SMMR Evaluation Team. Because the difference between the radiosonde corrections and those obtained by means of interpolated surface meteorological data has a standard deviation of 5.73 cm, the SMMR wet tropospheric correction is recommended for investigations sensitive to the wet tropospheric height correction accuracy.

Tapley, B. D.↗

NASA NTRS1983

First-order wetting transition at a liquid-vapor interface

Evidence from reflectance and contact angle measurements is presented that three-phase mixtures of i-C3H7OH-C7F14 exhibit a first-order wetting phase transition at the liquid-vapor interface at 38 C. Equilibration phenomena support this interpretation. Ellipsometry was used to measure the apparent thickness of the intruding layer in the three-phase mixture. At temperatures slightly above the wetting temperature T(w), the intruding layer's thickness is several hundred angstroms and its variation with temperature is extremely weak. Below T(w), three-phase contact can occur between the vapor and both the upper and lower liquid phases; one of the angles which characterizes this contact has a very simple temperature dependence. The thickness of the intruding layer, monitored as the solutions approached equilibrium, is found to depend quite weakly on the height spanned by the upper liquid phase in the vicinity of a first-order wetting transition.

Schmidt, J. W.↗

NASA NTRS1983

Evaporation from a partially wet forest canopy

The results of experimental studies of water storage in a Sitka-spruce canopy are presented and analyzed in terms of model simulations of evaporation. Wet-branch cantilever deflection was measured along with meteorological data on three days in August, 1976, to determine the relationship of canopy evaporation to wind speed and (hence) aerodynamic resistance. Two versions of a simple unilayer model of sensible and latent heat transport from a partially wet canopy were tested in the data analysis: model F1 forbids the exchange of heat between wet and dry foliage surfaces; model F2 assumes that this exchange is highly efficient. Model F1 is found to give results consistent with the rainfall-interception model of Rutter et al. (1971, 1975, 1977), but model F2 gives results which are more plausible and correspond to the multilayer simulations of Sellers and Lockwood (1981) and the experimental findings of Hancock and Crowther (1979). It is inferred that the role of eddy diffusivity for water vapor is enhanced relative to momentum transport, and that the similarity hypothesis used in conventional models may fail in the near vicinity of a forest canopy.

Hancock, N. H.↗

NASA NTRS1983

Gas flow across a wet screen - Analogy to a relief valve with hysteresis

The flow of gas through a wet fine-mesh screen is analyzed in terms of the capillary forces of the liquid wetting the screen and the pressure difference across the screen thickness driving the gas flow. Several different types of time-dependent flow are shown to be possible. The most interesting type is one in which the pressure difference opens small channels in the liquid, which are then closed rapidly by the wetting action of the liquid. The opening and closing exhibit hysteresis, and the flow is highly oscillatory.

Nachman, A.↗

NASA NTRS1985

Experimental and Theoretical Studies of Wetting and Multilayer Adsorption

The recent work with partially miscible binary liquid mixtures has established that the structure of the liquid-vapor interface can undergo a first-order phase transition from incomplete to complete wetting of the vapor as the temperature is raised. A discontinuity in the change of interfacial tension as a function of temperature at the phase transition has been predicted to occur in many systems and to play an important role in the growth of uniform composites from alloy melts at monotectic points. These measurements are the first to establish the order of the transition. Studies of capillary rise in SF6 in a unique interferometer have led to the first measurements of the thickness of wetting layers (or equivalently, multilayer adsorbed films) on a solid surface near a liquid-vapor critical point. Instabilities in wetting layers were observed. A theory for the instabilities is being developed and will be checked by both static and dynamic optical experiments. The effect of gravity on the apparent thickness of interfaces (as measured by ellipsometry) is under study.

Moldover, M. R.↗