Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VERTICAL FIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.4 to 0.9 of a Model of the "Swallow" with Outer Wing Panels Swept 25 degree with and without Power Simulation

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model (the "Swallow") with the outer wing panels swept 25 deg has been conducted in the Langley 16-foot transonic tunnel. The wing was uncambered and untwisted and had RAE 102 airfoil sections with a thickness-to-chord ratio of 0.14 normal to the leading edge. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. A pair of swept lateral fins and a single vertical fin were mounted on each engine nacelle to provide aerodynamic stability and control. Jets-off data were obtained with flow-through nacelles, stimulating the effects of inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained through a Mach number range of 0.40 to 0.90 at angles of attack and angles of sideslip from 0 deg to 15 deg. Longitudinal, directional, and lateral control were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control.

Runckel, Jack F.↗
NASA NTRS1977

Effect of wing fins on lift-generated wakes

A theoretical and experimental study has been made of the effect of wing-mounted fins on the vortex wakes of subsonic aircraft. The theory is used (a) to gain an understanding of wake alleviation by vortex injection and (b) to guide the experimental investigation. Wind-tunnel tests were used to evaluate the alleviation achievable and to find the optimum values for the various fin parameters. It was found that vertical fins mounted on the upper surface of a wing could lower the wake-induced rolling moments on an encountering wing by a factor of 3 or more. The most promising fin configuration found for the Boeing 747 model is a fin positioned 48% outboard from the centerline to the wingtip with a height of 0.014 span, a chord of 0.085 span, and an 18 deg angle of attack. This fin configuration caused a 10% increase in drag but no lift penalty.

Rossow, V. J.↗
NASA NTRS1992

Sailboard Fin Design

In high performance boardsailing, demands on the vertical fin or "skeg" often produce "spinout" - when the skeg loses horizontal lift creating a force imbalance and causing the tail of the board to slide sideways. Richard Caldwell, RACE Technology, Inc. used NASA airfoil technology to solve this problem and formed a business based on his solution. After determining that the spinout resulted from air ventilating down the low pressure side of the underwater fin, he adapted the airfoil technology to the design of a short board skeg, which would overcome the problem and lower the drag, resulting in improved performance. He patented his RACE 145 foil section, formed his company and later returned to Langley for additional technical assistance. The company's newest product is a rigid sail that also incorporates NASA technology and has excellent performance. This company no longer exists - product is no longer in production.

Source record↗
NASA NTRS1949

Wind-Tunnel Investigation of the Low-Speed Static Stability and Control Characteristics of a Model of Bell MX-776

An investigation has been made in the Langley stability tunnel to determine the low-speed static stability and control characteristics of a model of the Bell MX-776. The results of the investigation indicated that the basic model configuration was longitudinally stable in the angle-of-attack range from about -16 deg. to 16 deg. but that the stability was a minimum near O deg angle of attack. The data indicated an aerodynamic-center position about 0.64 body diameters behind the center of gravity at low angles of attack. Reduction in the size of the front horizontal fins increased the longitudinal stability. With 20 percent of the span of the normal front horizontal fins cut off the aerodynamic center was about 1.04 body diameters behind the center of gravity, and with front horizontal fins having the same area as the front vertical fins, the aerodynamic center was 2.26 body diameters behind the center of gravity (at low angles of attack).

Queijo, M. J.↗
NASA NTRS1983

Effect of modifications of aerodynamic characteristics of a single-stage-to-orbit vehicle at Mach 5.9

Hypersonic stability, control, and performance characteristics were determined on a single-stage-to-orbit vehicle based on control-configured stability concepts. The configuration (0.006-scale model) had a large body with a small 50 deg swept wing. Two vertical-fin arrangements were investigated which consisted of a large center-line vertical tail and small wing-tip fins. The wing-tip fins had movable surfaces called controllers which could be deflected outward. Longitudinal and lateral directional characteristics were obtained over an angle-of-attack rage from 0 deg to 40 deg. The effects of tip-fin controller deflection on roll- and yaw-control characteristics at a sideslip angle of 0 deg were obtained. This investigation was conducted in the Langley 20 Inch Mach 6 Tunnel.

Bernot, P. T.↗
NASA NTRS1945

Flight Measurements of Lateral and Directional Stability and Control Characteristics of the Grumman F8F-1 Airplane

This paper presents the results of flight tests to determine the lateral and directional stability and control characteristics of the Grumman F8F-1 airplane with three vertical-tail configurations. The data presented herein have no bearing on the performance characteristics of the airplane, which were not measured but which were considered to be exceptionally good. The conclusions reached regarding the lateral and directional stability and control characteristics may be summarized as follows: 1. It was found that the directional stability was poor with the production vertical tail. Addition of a 12-inch extension to the vertical fin and rudder produced a desirable improvement in directional stability and control characteristics. However, further enlargement of the vertical tail would be required to make the directional stability satisfactory in all respects. 2. There was a tendency for the rudder control force to overbalance at large angles of right sideslip with the modified vertical tails. There was no such tendency with the production tail configuration which included a dorsal fin. It was concluded that the dorsal fin should have been retained on the modified vertical tails. 3. The aileron control characteristics were better than those of many comparable airplanes which have been tested. However, the ailerons did not satisfy the Navy requirements for satisfactory flying qualities with regard to either control forces or rolling effectiveness. 4. The power of the rudder trimming tab proved to be inadequate and the tab should be enlarged and/or be provided with an increased deflection range.

Crane, H. L.↗
NASA NTRS1952

Wind-Tunnel Investigation of the Static Longitudinal Stability Characteristics of a 0.15-Scale Model of the Hermes A-1E2 Missile at High Subsonic Mach Numbers

The static longitudinal stability characteristics of a 0.15-scale model of the Hermes A-lE2 missile have been determined in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.98, corresponding to Reynolds numbers, based on body length, of 12.3 x 10(exp 6) to 17.1 x 10(exp 6). This paper presents results obtained with body alone and body-fins combinations at 0 degrees (one set of fins vertical and the other set horizontal) and 45 degree angle of roll. The results indicate that the addition of the fins to the body insures static longitudinal stability and provides essentially linear variations of the lift and pitching moment at small angles of attack throughout the Mach number range. The slopes of the lift and pitching-moment curves vary slightly with Mach number and show only small effects due to the angle of roll.

Alford, William J., Jr.↗
NASA NTRS1994

Development of a low-aspect ratio fin for flight research experiments

A second-generation flight test fixture, developed at NASA Dryden Flight Research Center, offers a generic testbed for aerodynamic and fluid mechanics research. The new fixture, a low-aspect ratio vertical fin shape mounted on the centerline of an F-15B aircraft lower fuselage, is designed for flight research at Mach numbers up to 2.0. The new fixture is a composite structure with a modular configuration and removable components for functional flexibility. This report describes the multidisciplinary design and analysis approach used to develop the fixture. The approach integrates conservative assumptions with simple analysis techniques to minimize the time and cost associated with its development. Presented are the principal disciplines required for this effort, which include aerodynamics, structures, stability, and operational considerations. In addition, preliminary results from the first phase of flight testing are presented. Acceptable directional stability and flow quality are documented and show agreement with predictions. Future envelope expansion activities will minimize current limitations so that the fixture can be used for a wide variety of high-speed aerodynamic and fluid mechanics research experiments.

Richwine, David M.↗
NASA NTRS1974

Flight investigation of effects of a fan-in-fin yaw control concept on helicopter flying-quality characteristics

Flight-test results which describe flying-quality factors related to the fan-in-fin yaw control concept as utilized on a pre-production version of a European helicopter are presented. Design compromises to be considered with this concept are also presented. The large, fixed vertical fin associated with the fan-in-fin system was helpful in maneuvering flight, but introduced several flying-quality problems when combined with the fan.

Kelley, H. L.↗
NASA NTRS1980

The prediction of pressure distributions on an arrow-wing configuration including the effect of camber, twist, and a wing fin

Wind tunnel tests of an arrow wing body configuration consisting of flat, twisted, and cambered twisted wings were conducted at Mach numbers from 0.40 to 2.50 to provide an experimental data base for comparison with theoretical methods. A variety of leading and trailing edge control surface deflections were included in these tests, and in addition, the cambered twisted wing was tested with an outboard vertical fin to determine its effect on wing and control surface loads. Theory experiment comparisons show that current state of the art linear and nonlinear attached flow methods were adequate at small angles of attack typical of cruise conditions. The incremental effects of outboard fin, wing twist, and wing camber are most accurately predicted by the advanced panel method PANAIR. Results of the advanced panel separated flow method, obtained with an early version of the program, show promise that accurate detailed pressure predictions may soon be possible for an aeroelasticity deformed wing at high angles of attack.

Bobbitt, P. J.↗
NASA NTRS1985

Wind tunnel acoustic study of a propeller installed behind an airplane empennage: Data report

The open test section of the NASA-Ames 7- by 10- ft wind tunnel was used for an acoustic test of a propeller mounted behind an airplane empennage. The empennage was attached to a model fuselage and the propeller with its electric motor drive was mounted separately so that the relative positions of empennage and propeller could be varied. A single vertical fin, and a V-tail with, and without, a dorsal fin configurations were used the model propeller had four blades (SR-1). Data were recorded at several locations for two tunnel flow speeds (45.7) and 62.5 m/s) and propeller speeds in the range 4000 to 8200 rpm. Data reduction was performed in narrowband and one-third octave band spectra, with emphasis on harmonics of the passage frequency blade. The influence of flow speed, propeller rpm, empennage configuration, axial and vertical separation between propeller axis and empennage centerline, and empennage angle of incidence on propeller harmonic levels and acoustic field directivity are studied.

Wilby, J. F.↗
NASA NTRS1980

Measurement of Aircraft Speed and Altitude

Problems involved in measuring speed and altitude with pressure-actuated instruments (altimeter, airspeed indicator, true-airspeed indicator, Machmeter, and vertical-speed indicator) are examined. Equations relating total pressure and static pressure to the five flight quantities are presented, and criteria for the design of total and static pressure tubes are given. Calibrations of typical static pressure installations (fuselage nose, wing tip, vertical fin, and fuselage vent) are presented, various methods for flight calibration of these installations are described, and the calibration of a particular installation by two of the methods is described in detail. Equations are given for estimating the effects of pressure lag and leaks. Test procedures for the laboratory calibration of the five instruments are described, and accuracies of mechanical and electrical instruments are presented. Operational use of the altimeter for terrain clearance and vertical separation of aircraft is discussed, along with flight technical errors and overall altitude errors of aircraft in cruise operations. Altitude-measuring techniques based on a variety of properties of the Earth and the atmosphere are included. Two appendixes present airspeed and altitude tables and sample calculations for determining the various flight parameters from measured total and static pressures.

Gracey, W.↗
NASA NTRS1954

Wind-tunnel Tests of a Model of a Wingless Fin-controlled Missile to Obtain Static Stability and Control Characteristics Through a Range of Mach Numbers from 0.5 to 0.88

An investigation at medium to high subsonic speeds has been conducted in the Langley low-turbulence pressure tunnel to determine the static stability and control characteristics and to measure the fin normal forces and moments for a model of a wingless fin-controlled missile. The data were obtained at Reynolds number of 2.1 x 10(6) based on the missile maximum diameter or 17.7 x 10(6) based on missile length; this Reynolds number was found to be large enough to avoid any large scale effects between the test and the expected flight Reynolds number. With the horizontal-fin deflection limited to a maximum of 6 degrees, longitudinally stable and trimmed flight could not be maintained beyond an angle of attack of 17 degrees for a Mach number of 0.88 and beyond 20 degrees for a Mach number of 0.50 for any center-of-gravity location without the use of some auxiliary stability or control device such as jet vanes. Mach number had no appreciable effect on the center-of-pressure positions and only a slight effect on neutral-point position. There was a shift in neutral-point position of about 1 caliber as the angle of attack was varied through the range for which the neutral point could be determined. Yawing the model to angles of sideslip up to 7 degrees had little effect on the longitudinal stability at angles of attack up to 15 degrees; however, above 15 degrees, the effect of sideslip was destabilizing. With the vertical fins at a plus-or-minus 6 degree roll deflection, the rolling moment caused by yawing the model at high angles of attack could be trimmed out up to angles of sideslip of 6.5 degrees and an angle of attack of 26 degrees for a Mach number of 0.50; this range of sideslip angles was reduced to 3 degrees at a Mach number of 0.88. The data indicated that, at lower angles of attack, the trim range extended to higher angles of sideslip. The total normal-force and hinge-moment coefficients for both horizontal fins were slightly nonlinear with both angle-of-attack and fin deflection. The effect of Mach number was to reduce the slopes of the hinge-moment coefficient with angle of attack and deflection angle. In general, the effort of increasing the sideslip angle was to reduce the values of the fin normal-force and hinge-moment coefficients.

Burrows, Dale L↗
NASA NTRS1972

Aerodynamic stability and control characteristics of TBC shuttle booster AR-11981-3

A scale model of the Boeing Company space shuttle booster configuration 3 was tested in the MSFC 14-inch trisonic wind tunnel. This test was proposed to fill-in the original test run schedule as well as to investigate the aerodynamic stability and control characteristics of the booster with three wing configurations not previously tested. The configurations tested included: (1) a cylindrical booster body with an axisymmetric nose, (2) clipped delta canards that had variable incidence from 0 deg to -60 deg, (3) different aft body mounted wing configurations, (4) two vertical fin configurations, and (5) a Grumman G-3 orbiter configuration. Tests were conducted over a Mach range from 0.6 to 5.0.

Phelps, E. R.↗
NASA NTRS1974

Experimental low-speed and calculated high-speed aerodynamic characteristics of a hypersonic research airplane concept having a 65 deg swept delta wing

An experimental wind-tunnel investigation has been carried out to determine the static longitudinal, lateral, and directional stability and control characteristics of a model of a large-body, delta-wing hypersonic research airplane concept at low speed. This investigation was conducted at a dynamic pressure of 239.4 Pa (5 psf) and a Reynolds number, based on fuselage length, of 2 million. The configuration variables included vertical fins, engine modules, canards, and a canopy. The aerodynamic results of a computer study at Mach numbers of 3 to 12 are presented.

Penland, J. A.↗
NASA NTRS1974

Feasibility study of the transonic biplane concept for transport aircraft application

Investigations were conducted to evaluate the feasibility of a transonic biplane consisting of a forward-mounted swept-back lower wing, a rear-mounted swept-forward upper wing, and a vertical fin connecting the wings at their tips. This wing arrangement results in significant reductions in induced drag relative to a monoplane designed with the same span, and it allows for a constant-section fuselage shape while closely matching an ideal area distribution curve for M = 0.95 cruise. However, no significant reductions in ramp weight were achieved for the biplane relative to a monoplane with the same mission capability. Flutter analyses of the biplane revealed both symmetric and antisymmetric instabilities that occur well below the required flutter speed. Further studies will be required to determine if acceptable flutter speeds can be achieved through the elimination of the instabilities by passive means or by active controls. Configurations designed for other missions, especially those with lower Mach numbers and lower dynamic pressures, should be examined since the geometries suitable for those design constraints might avoid the weight penalties and flutter instabilities which prevent exploitation of induced drag benefits for the configuration studied.

Lange, R. H.↗
NASA NTRS1978

Development of advanced composite structures

Composite structure programs: the L-1011 Advanced Composite Vertical Fin (ACVF), the L-1011 Advanced Composite Aileron, and a wing study program were reviewed. These programs were structured to provide the technology and confidence for the use of advanced composite materials for primary and secondary structures of future transport aircraft. The current status of the programs is discussed. The results of coupon tests for both material systems are presented as well as the ACVF environmental (moisture and temperature) requirements. The effect of moisture and temperature on the mechanical properties of advanced composite materials is shown. The requirements set forth in the FAA Certification Guidelines for Civil Composite Aircraft Structures are discussed as they relate to the ACVF.

Stauffer, W. A.↗
NASA NTRS1976

Flight service evaluation of an advanced composite empennage component on commercial transport aircraft

The development and flight evaluation of an advanced composite empennage component is presented. The recommended concept for the covers is graphite-epoxy hats bonded to a graphite-epoxy skin. The hat flare-out has been eliminated, instead the hat is continuous into the joint. The recommended concept for the spars is graphite-epoxy caps and a hybrid of Kevlar-49 and graphite-epoxy in the spar web. The spar cap, spar web stiffeners for attaching the ribs, and intermediate stiffeners are planned to be fabricated as a unit. Access hole in the web will be reinforced with a donut type, zero degree graphite-epoxy wound reinforcement. The miniwich design concept in the upper three ribs originally proposed is changed to a graphite-epoxy stiffened solid laminate design concept. The recommended configuration for the lower seven ribs remains as graphite-epoxy caps with aluminum cruciform diagonals. The indicated weight saving for the current advanced composite vertical fin configuration is 20.2% including a 24 lb growth allowance. The project production cost saving is approximately 1% based on a cumulative average of 250 aircraft and including only material, production labor, and quality assurance costs.

Source record↗