Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermal hydraulic modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

FY22 Status Report on the ART-GCR CMVB and CNWG International Collaborations

This work presents the numerical model for the high temperature test reactor (HTTR) loss of forced cooling (LOFC) experiment with the INL codes Griffin, BISON, and RELAP-7, based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. Promising results were obtained, with the overall behavior of the reactor successfully captured. Changes in the heat transfer coupling, as compared to the fiscal year (FY)-21 model, enabled drastic improvement of the steady-state solution, both in terms of computational time and global energy discrepancies. The former was reduced by a factor of roughly 60, whereas the latter decreased from 11% to less than 2%. Furthermore, the discrepancy in the steady-state multiplication factor was improved from +2,300 and +2,900 pcm (for the 30 and 9 MW cases) to -700 and +1,200 pcm, respectively, and now falls well within the large measurement uncertainties stemming from graphite impurities. Validation of the Monte Carlo model used to generate cross sections was also performed against available measurements. Though significant, the discrepancies remain acceptable overall in light of the large uncertainty. Numerous improvements are still needed to better compare with the experiment involving the 9 MW case and to instill greater confidence in the model’s ability to accurately predict the 30 MW behavior. Specifically, the power levels predicted by the 9 MW transient simulation following re-criticality remain low, pointing to an underestimation of the passive cooling of the core. A key aspect of future work will be to better understand the flow pattern during the LOFC event, particularly to determine if natural or forced convection is occurring inside the reactor pressure vessel (RPV). More generally, additional validation data would be immensely useful for further enhancing the numerical model and better matching the experiments. In addition, a more sophisticated thermal-hydraulics model that simulates all the channels as a single system model should be considered to take into account the rest of the primary loop. Finally, even if the results are in better agreement with the experiments, sensitivity analysis and uncertainty quantification will be necessary to evaluate the model uncertainty.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Experimental measurements and mathematical modeling of cold plate for aviation thermal management

Herein, this study, which has been motivated by the recent applications of the cold plate device in aviation thermal management, reports on physics-based mathematical models derived from the conservation laws of mass, momentum, and energy, and empiricism-based models. One of the objectives of the present work is to report on an elaborate and successful experimental work carried out on an additively manufactured device for the purpose of rigorously validating the numerical predictions. The excellent agreement between the numerical predictions and measured performance provides much needed confidence in the implementation, in the software package, of the offset-strip fin passage correlations, as well as in the software implementation of user-defined wavy fin correlations for aerospace heat exchangers and cold plates operating with ram air at Reynolds numbers below 8000. The contributions of this work can also be found in the development of a new and accurate thermal-hydraulic analysis procedure, referred to in this paper as plate-fin analogy. Results from this procedure are compared with those from thermal resistance network. The comparative study in this paper of the bulk and discrete enthalpy flux method is also new, as is the relative assessment of four off-set strip fin thermal-hydraulic models.

42 ENGINEERING↗
DOE OSTI2025

Towards machine-learning a fully-coupled constitutive model for thermal-hydraulic fracture in geothermal systems: phase I (Final Report)

This project, entitled “Towards machine-learning a fully-coupled constitutive model for thermal-hydraulic fracture in geothermal systems: phase I,” addresses challenges in understanding and controlling subsurface fracture networks, which are crucial for applications like deep geothermal heat mining and deep-crustal minerals/metals/hydrogen extraction. The research focuses on advancing the understanding of coupled thermal-hydro-mechanical-chemical (THMC) processes in geologic materials, particularly under the high temperature and pressure conditions found in the deep crust. This seed grant focused specifically on thermal cracking and the development of new constitutive models. Significant progress was made in both experimental and theoretical domains. To study micro-scale fracture formation, the project demonstrated the ability to create thermal cracking under stress in granite samples using a Paterson Gas-medium Deformation Apparatus.

15 GEOTHERMAL ENERGY↗
NASA NTRS2009

Proposed Schematics and Modeling Results for a Lunar Portable Life Support System

The Constellation Space Suit Element (CSSE) is an integrated assembly made up of primarily a Pressure Garment System (PGS) and a Portable Life Support System (PLSS). The PLSS is further composed of an oxygen (O2) subsystem, a ventilation subsystem, and a thermal subsystem. This paper baselines a detailed schematic of the CSSE PLSS to provide a basis for current and future CSSE PLSS development efforts. Both context diagrams and detailed schematics describe the hardware components and overall functions for all three of the PLSS subsystems. Additionally, PLSS functions are presented for multiple operational scenarios as follows: 1) Nominal Extravehicular Activity (EVA) Mode; 2) Umbilical Modes; a) No Recharge, b) With Recharge; 3) Decompression Sickness (DCS) Treatment Mode; 4) Buddy Mode; 5) Secondary O2 Modes; a) Helmet Purge; b) Suit Purge; c) Operational; and 5) PLSS Removed Umbilical Mode. A performance modeling effort is being performed to provide a preliminary confirmation of this layout and the current state of the thermal hydraulic modeling efforts being conducted for the PLSS is presented. The goal of these efforts is to provide realistic simulations of the PLSS under various modes of operation. Modeling approaches and assumptions are discussed as well as component model descriptions. Results from the models are included that show PLSS operations at steady-state and transient conditions. Finally, conclusions and recommendations are offered that summarize results, identify PLSS design weaknesses uncovered during review of the analysis results, and propose areas for improvement to increase model fidelity and accuracy.

Conger, Bruce↗
DOE OSTI2025

Development of a Pronghorn Model of the High Temperature Engineering Test Reactor: Preliminary Results from Loss of Forced Cooling #3 [Slides]

This presentation contains results from a Pronghorn model of the High Temperature Engineering Test Reactor (HTTR) operated by the Japan Atomic Energy Agency. The model was used to simulate a loss of forced cooling (LOFC) experiment. This presentation contains preliminary results from a standalone thermal hydraulics model of this LOFC test and some discussion of the results compared to data

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
NASA NTRSDate not supplied

Heat Pipe Heat Exchanger for Nuclear Electric Propulsion Power Conversion System

Heat pipe reactors have been considered by the Space Nuclear Propulsion program for Nuclear Electric Propulsion (NEP) power conversion systems and will require the use of heat exchangers to transfer heat via heat pipes to the Brayton working fluid from the reactor. Sodium (Na) and lithium (Li) were considered as viable working fluids inside the heat pipes which were assumed to have the same geometry based on studies and information from the Los Alamos National Laboratory. The heat exchanger was assumed to be a rectangular duct with heat pipes serving as tubes from previous NEP work and recommendations. Based on this geometry, Zukauskas correlations were used to model the convective heat transfer and pressure losses. Parametric sizing of the reactor component involved operational limits-based heat pipe thermal hydraulic modeling in cohesion with required user input geometry for the in-core lattice and various subcomponents. This work considered various power conversion inlet temperatures (PCIT) of 1100 K, 1150 K, and 1200 K for Na heat pipes and 1100 K, 1150 K, 1200 K, and 1400 K for Li heat pipes based on recommendations from prior work. Using these different PCITs, the subsystem masses and pressure losses were determined and analyzed. Na showed a lower overall operating temperature and about a fifth of the maximum heat throughput capability than that of Li for the same geometry. Due to this, the entire Na-based subsystem ended up being three times more massive than the Li-based subsystem given five times the required number of heat pipes. At the low PCIT of 1100 K, the Na-based subsystem exhibited the lowest pressure losses given the large overall cross sectional flow area and relatively low frictional pressure losses. However, as the PCIT increased, the frictional pressure losses increased resulting in higher pressure losses at the 1200 K PCIT than Li-based subsystem. However, the Li-based subsystem exhibited the largest pressure losses of all analyzed cases at the 1400 K PCIT due to the low density of the Brayton working fluid at this temperature.

electric↗
DOE OSTI2024

RELAP5-3D HTGR Validation Work at Idaho National Laboratory

Prismatic block-type high-temperature gas-cooled reactors (HTGRs) were built in the United States decades ago, and now advanced reactor vendors are seeking to deploy them again for a variety of applications. Deploying these reactors requires modelling and simulation tools that have been validated against conditions representative of the HTGR application. Idaho National Laboratory (INL) is leading the execution an of HTGR thermal hydraulics benchmark to accelerate the validation of thermal hydraulics modelling and simulation tools for these applications. That benchmark is based on a facility called the High Temperature Test Facility (HTTF). This work provides an overview of work conducted at INL over the last 2 years to validate RELAP5-3D against data from HTTF. This presentation shows results from multiple RELAP5-3D models and an HTTF experiment to assess the impact of certain modelling assumptions on results. The contents of this talk sit on the cutting edge of RELAP5-3D validation for HTGR analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Initial development of a generic fluoride salt-cooled reactor model

Fluoride high-temperature reactors (FHRs) are high-temperature, low-pressure reactor concepts that use tri-structural isotropic (TRISO) fuel and molten fluoride salt coolant. These reactors have the potential to provide both electrical power and high-temperature process heat. We used generic FHR parameters for a pebble-bed FHR to develop an initial model with fresh fuel for a generic FHR (gFHR) in MELCOR and SCALE (NEWT and KENO). In this paper, we present the development of our gFHR models, which will serve as the baseline for a sensitivity and uncertainty analysis to quantify the range of possible source terms for FHRs in severe accidents. We present MELCOR results for fuel and coolant temperatures through the core, a nodalization study for the steady-state thermal hydraulic model, and development of reactor physics models in SCALE. As this work progresses, these models will be used to calculate source terms for a loss-of-forced-flow accident and to conduct a sensitivity study on this accident to establish a range of possible source terms. SCALE will provide reactor physics parameters like isotopic inventory, decay heat generation, and temperature coefficients of reactivity. Using the uncertainty quantification tools within SCALE, we will generate distributions for those parameters and will use the uncertainty quantification code RAVEN or DAKOTA to sample those distributions in MELCOR to quantify the impact of reactor physics and thermal hydraulic uncertainties on FHR source terms. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Development of a MOOSE thermal model of the MPC-32 canister and HI-STORM overpack

Nuclear power is a significant source of electricity in the United States, but the average age of nuclear power plants is around 40 years old. The safe management of the spent nuclear fuel (SNF) is a key aspect of the back-end of the nuclear fuel cycle. Spent fuel dry storage systems are becoming a popular and effective solution in this area, given the absence of a final disposal system. The spent fuel cask system (dry cask method) provides a feasible solution to maintain spent fuel for 60 years before final disposal. Dry cask storage has many characteristics that make it attractive. It fulfills the safety requirements of the Nuclear Regulatory Commission (NRC) while providing modularity and flexibility to contractors. The HI-STORM overpack and MPC-32 canister are the main parts of the HI-STORM 100 dry cask storage system. These components remove heat from the system using natural circulation, requiring no human intervention. This is the characteristic that provides passive heat removal and low maintenance features in dry cask storage systems. To develop a thermal model for a dry cask storage system, the physics behind the system should be defined clearly. There are two natural circulation loops in the system; circulation of helium cools down the nuclear assemblies in the MPC, while circulation of air cools down the walls of the MPC. This work aims to develop a thermal model of the MPC-32 canister and HI-STORM overpack using the Multiphysics Object-Oriented Simulation Environment (MOOSE). MOOSE is an open-source framework developed by Idaho National Laboratory (INL) for multiscale, multiphysics simulations. In this study, we will investigate and demonstrate the thermal-hydraulics modeling capabilities of the MOOSE framework, including natural circulation, heat transfer, and porous flow.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Progress Towards the Validation of a new RELAP5-3D model of the High Temperature Test Facility

Validation is a key step in the development of any type of systems model. As the next generation of reactors approaches, the need for codes that have been validated for these new types of systems continues to grow. An example of a prominent option is the Reactor Excursion Leak Analysis Program (RELAP5-3D), developed by Idaho National Laboratory. This code was developed for the purpose of systems level thermal-hydraulic modeling of light water reactors (LWRS) and postulated transients that can occur in LWRS.RELAP5-3D has been substantially validated against LWR data. Due to its long history as a reactor safety analysis tool, there has been an effort to adapt RELAP5-3D for the purposes of advanced reactor concepts such as prismatic high-temperature gas-cooled reactors (HTGRs). However, RELAP5-3D has not nearly been validated and verified for HTGRs to the degree of LWRs, warranting verification and validation opportunities with computational benchmarks and existing experimental facilities. Examples of such facilities include the modular high-temperature gas-cooled reactor (MHTGR) 350 and the high temperature engineering test reactor (HTTR) from Japan. The MHTGR 350 is a benchmark design concept for code-to-code verification purposes; therefore, it does not provide any experimental data for validation opportunities The HTTR provides useful multiphysics validation data but does not have the in-core instruments to generate thermal-hydraulic experimental data to help with RELAP5-3D validation. Consequently, a facility that could provide key in-core temperatures for thermal-hydraulic validation was still needed. The High Temperature Test Facility (HTTF) is an integral effects facility for HTGR thermal hydraulics developed and operated by Oregon State University. HTTF represents ¼ length scale of the General Atomics MHTGR and is rated for a total power of 2.2 MW. Axially, the core consists of an upper and lower reflector and 10 blocks, numbered from bottom to top (Block 1 is right above lower reflector). The core is heated via graphite resistive heater rods, with respective channels distributed throughout the core. The primary coolant is helium and heat can radiate out of the core to the reactor cavity cooling system (RCCS), which is cooled by water. The primary purpose of the facility is to investigate pressurized conduction cooldown (PCC) and depressurized conduction cooldown (DCC) transients, which are also referred to as the pressurized and depressurized loss of forced cooling respectively. Two experiments were chosen to perform the validation study with a RELAP5-3D model of HTTF. These experiments are PG-27 (PCC) and PG-29 (DCC). These were chosen based off of the quality of available experimental data before and during the experiment which led to their inclusion in the HTGR Thermal Hydraulics Benchmark.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Risk-Informed MultiPphysics BestEestimate Plus Uncertainties (BEPU) Application Development of RELAP5-3D Perturbation Model

The United States nuclear industry is facing a strong challenge to ensure maximum safety while enhancing economic benefit. Safety is a key parameter to all aspects related to light water reactor (LWR) nuclear power plants (NPPs), especially cost savings. Since the goal is to extend the lifetimes of these NPPs, the traditional deterministic safety concept may not guarantee a current economic asset. The Light Water Reactor Sustainability (LWRS) Program has been promoting a wide range of research and development (R&D) in this field to maximize the safety, economics, and performance of these NPPs through improved scientific understanding. One of the best practices to achieve this goal is to identify and optimize safety margins, which can lead to cost reduction. To do this, under the LWRS framework, the Risk-Informed Systems Analysis (RISA) Pathway will focus on the optimization of safety margin and minimization of uncertainties to ensure both safety and economics at the highest level. The RISA Pathway will provide enhanced capabilities for analyzing and characterizing LWR systems performance by developing and demonstrating methods, tools, and data to enable risk-informed margins management (RIMM). The goals of the RISA Pathway are twofold: (1) deploy the risk-informed tools and methods that enable better representation of safety margins and factors that contribute to cost and safety; and (2) conduct advanced risk assessment applications with industry to support margin management strategies that enable more cost-effective plant operation. The tools and methods provided by the RISA Pathway will support effective margin management for both active and passive safety systems, structures, and components (SSC) of an NPP. The tools and methods used in the RISA Pathway should have high confidence and highest technical maturity for and implementation to industry at its current setting. They should also have a capability to support risk-informed decision making for both probabilistic and deterministic elements of safety. The RISA Pathway will, therefore, perform a comprehensive assessment of verification and validation (V&V) status of RISA Toolkit to enhance credibility RISA Toolkit which be used by industry. This report summarizes RELAP5-3D development activities for best estimated and uncertainty (BEPU) capability to support ongoing RISA Pathway pilot projects for risk informed uncertainty quantification applications. Work scope includes (1) development of initial perturbation model for selected closure laws and (2) testing of suitable probability distribution functions (PDF) for the selected correlations. Developed BEPU modules are tested with selected separate effect cases and compared with conventional thermal-hydraulics model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Accident event progression, gaps, and key performance indicators for steam generator tube rupture events in water-cooled SMRs: A review

According to historical records of reactor-related incidents, a steam generator tube rupture (SGTR) is one of the most common occurrences at operating pressurized water reactors (PWRs). Such design-basis accidents (DBAs) could lead to a direct path for radionuclides to be released to the atmosphere via the safety and relief valves, making assessments of radionuclide discharge from operating nuclear power plants (NPPs) into the environment crucial for ensuring safety. In such analyses, the primary focus has been on the extent of radioactive release, not the potential damage to the core. Moreover, significant and timely intervention by operators is needed during the initial stages of SGTRs in order to avert overfilling of the SGs, as well as to restrict the dissemination of radioactive materials. Determining the event sequence and phases that occur during an SGTR incident in an advanced passive (e.g., AP1000) water-cooled nuclear reactor is crucial for implementing effective passive safety systems (PSSs) for a specific water-cooled small modular reactor (SMR) design. Here this study provides a comprehensive review of the accident event progression, associated physical phenomena, knowledge gaps, and key performance indicators that must be evaluated and assessed in thermal-hydraulics models, based on relevant test data, respectively.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

NEA HTTR LOFC Project Test#3 Benchmark Results

In the second half of FY23, the High Temperature Engineering Test Reactor (HTTR) Loss Of Forced Cooling (LOFC)#3 data for the 9 MW test case with Vessel Cooling System (VCS) off were made available through the Nuclear Energy Agency (NEA) LOFC project framework; the neutronic model developed for the initial test (LOFC#1) achieved a satisfactory level of maturity, demonstrating its accuracy in predicting power evolution and core re-criticality, but LOFC#3 should be used primarily to investigate thermal hydraulic phenomena, as the reactor was shut down prematurely due to overheating in the upper reactor components, which prevented re-criticality; this report focuses on advancing the HTTR thermal hydraulic model to accurately simulate the LOFC#3 scenario, including simulating the LOFC#3 benchmark and generating the corresponding benchmark specifications, aiming to ensure consistency across participant models and provide essential data for future participants, including private industry stakeholders seeking to validate their computational tools.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Species Transport Framework Development in SAM for System-Level Tritium Source Term Analysis

The SAM code is under development as a modern system-level modeling and simulation tool for advanced non–light water reactor safety analyses, with recent efforts to add capabilities to evaluate radiological source term risks in these novel reactor concepts. By leveraging the established system-level multiphysics thermal-hydraulic models in SAM, a framework for tightly coupled species transport modeling has been integrated into the code for engineering-scale source term evaluation. This species transport framework was first applied to the simulation of tritium, which is a well-known source term in conventional light water reactors. Tritium poses a unique risk in salt-cooled reactors, especially those with lithium-bearing salts such as the fluoride salt–cooled high-temperature reactor (FHR) concept, as tritium is generated in the salt coolant in significant quantities due to neutron interactions. A compounding factor is the increased mobility of tritium at high temperatures, which is able to permeate through metals while also potentially being retained in graphite pebbles and structures. Engineering-scale models for the tritium transport pathways in a FHR have been developed using the new species transport framework in SAM. The capabilities are assessed through analytical verification problems and validated with data from a graphite retention experiment. In conclusion, the system-level model is demonstrated by performing an initial estimate of baseline tritium generation and flows in a generic reference SAM FHR model, setting a foundation for future studies of source term transient analysis with the potential for further multiscale and multiphysics integration.

SAM↗
NASA NTRS1993

Particle bed reactor modeling

The topics are presented in viewgraph form and include the following: particle bed reactor (PBR) core cross section; PBR bleed cycle; fuel and moderator flow paths; PBR modeling requirements; characteristics of PBR and nuclear thermal propulsion (NTP) modeling; challenges for PBR and NTP modeling; thermal hydraulic computer codes; capabilities for PBR/reactor application; thermal/hydralic codes; limitations; physical correlations; comparison of predicted friction factor and experimental data; frit pressure drop testing; cold frit mask factor; decay heat flow rate; startup transient simulation; and philosophy of systems modeling.

Sapyta, Joe↗
DOE OSTI2023

Scoping Study for Fast Flux Testing in the Advanced Test Reactor

The value of fast spectrum reactors remains prominent in the nuclear technology portfolio. The performance of these reactors can be maximized with advancements in nuclear fuel technologies, but development of these technologies is currently held back by lack of fast spectrum test reactors available to the United States. Spectral modification of experiment positions in the thermal spectrum Advanced Test Reactor (ATR) has long been used to support fast reactor fuel development, but these methods have not been progressed to their full potential. This study investigated the use of concentric rings of aluminum-clad fuel plates in ATR flux traps and thermal neutron absorbing filters to increase fast neutron flux on test specimens. This concept was termed the Boosted Energy Advanced Spectrum Test (BEAST). This approach will enable irradiation of advanced fuel designs in prototypic-length fuel pins and representative flux environment to support post irradiation exams, enable transient testing, and produce the type of data that will permit lead test assembly irradiations in true Sodium Fast Reactors (SFRs) when they become available. Neutronic predictions were performed to investigate BEAST design options and thermal hydraulic models were produced to ensure feasibility of BEAST. Two versions were considered based on the geometric limitations of ATR’s small and large flux traps. The small version was found to be preferable due to slightly higher fast flux and fast-to-thermal neutron ratio. Perhaps more influentially, the small flux trap option was also preferred to avoid conflict with ongoing very high temperature reactor fuel irradiation programs in ATR’s large northeast flux trap. The small flux trap option provided less than half the test volume of the large version, but still had adequate volume for seven SFR pins in cross section which could be stacked two-high in ATR’s 1.2m long core to accommodate up to 14 EBR-II size pins. The preference for the small flux trap configuration should be revisited if additional collaborative test programs emerge with the need to irradiate a significant volume of additional specimens. Calculations were performed regarding a lithium deuteride ring to convert thermal neutrons into 14 MeV fusion neutrons. At the time this report was written these calculations were partially complete and it remains to be seen whether the concept would be worth including in BEAST. Given the preference for the small flux trap option, which does not afford enough room for the 14 MeV ring, it was concluded to defer future work on the lithium deuteride ring. This decision could be revisited if fusion material research programs emerge for collaborative testing in BEAST. A cadmium-lined specimen holder design was found to be adequate in filtering thermal neutrons and preferred over other neutron absorbers based on past experience with cadmium baskets. It was acknowledged that cadmium-bearing hardware would become depleted and need to be replaced occasionally, which appeared feasible from a mechanical design perspective. Neutronic studies investigated different enrichment levels in the booster fuel using uranium-molybdenum alloy dispersion fuel which has performed well in past ATR irradiations. Both options were able to drive fuel pins to SFR-like fission heating rates. The high enriched booster fuel option outperformed the low enriched option by ~20% on key metrics including fast flux and fast-to-thermal ratio, but the low enriched option was favored in order to broaden options for potential fuel suppliers. The preferred BEAST design options including cadmium filter with low enriched booster fuel in the small flux trap configuration was predicted to achieve 6.2E14 n/cm2sec fast flux (>0.1 MeV) with a fast-to-thermal ratio of 44.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

An Overview of the Molten Salt Thermal Properties Database–Thermophysical, Version 4.0 (MSTDB-TP V.4.0)

A central repository of thermophysical and thermochemical properties of molten salt compositions of relevance to molten salt reactors (MSRs) is vital in supporting the broad community of MSR developers, who are at various stages of developing and deploying their reactor designs. In general, these MSR designs differ significantly from developer to developer (e.g., with respect to the hardness of the neutron spectra, level of fissile loading, target multicomponent temperatures and power levels, and moderating capabilities). Therefore, the fuel and coolant salts being considered vary greatly: they may be chlorides or fluorides, they utilize different actinides at different ratios, and the cations in the melt are selected based on perceived advantages and disadvantages. Considering the general need for thermal properties, and the vastness of the array of potential candidate salt mixtures, the Molten Salt Thermal Properties Database (MSTDB) was initiated in 2018 with the goal of providing thermophysical and thermochemical characterization of key molten salt compounds and mixtures across their temperature and compositional domains. The MSTDB is thus divided into the thermophysical arm (MSTDB-TP) and the thermochemical arm (MSTDB-TC). The MSTDB is an effort funded by the Department of Energy, Office of Nuclear Energy (DOE-NE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, and the MSR Campaign. This report provides an overview of the MSTDB-TP v4.0 in terms of the data contained within, the state of the tools used to access the data, the availability of predictive models that leverage the raw data in the database, the preliminary status of developmental efforts that are currently underway, and an account of future goals for MSTDB-TP. The primary goal for the update from MSTDB-TP v.3.1 to v4.0 was the incorporation of surface tension data into the database; this property is important for thermal hydraulics modeling and species transport in other tools that have been developed under the NEAMS program. A breakdown of the surface tension data that have been added into MSTDB-TP v4.0 is provided herein, and the manner in which the quality of the data has been assessed is also documented. For MSTDB-TP v4.0, newly published thermophysical property data—primarily from collaborative experimental efforts under the MSR Campaign—have been incorporated into the database, and the resulting expansion is documented here. Because of the size to which MSTDB-TP has grown, the raw data format has now been recast into JavaScript Object Notation (JSON) format for easier connection with the MSTDB-TP application programming interface (API). Saline; the pre-existing comma-separated value (CSV) format has been deprecated but is still maintained, accessible, and up to date. As a final effort in packaging the MSTDB-TP v4.0 update, the graphical user interface (GUI) for MSTDB has been updated to allow full accessibility to the density and viscosity predictive models, which are based on Redlich-Kister expansions of MSTDB-TP raw data. Some other major aspects of this report, in terms of preliminary and future work, include: (1) documentation of the formalism and preliminary testing of a kinetic theory model that may act as a predictive model for thermal conductivity; (2) documentation of the candidate predictive models that may be considered in the future for surface tension, making use of the surface tension data now in MSTDB-TP v4.0; (3) a preliminary account of a data collection process that will enable the filling of additional gaps within MSTDB-TP, namely with data which have been collected computationally (e.g., through ab initio molecular dynamics).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗