Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Test Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

CFD Validation with LDV Test Data for Payload/Fairing Internal Flow

Flowfield testing of a 1/5th scale model of a payload/fairing configuration, typical of an expendable launch vehicle, has been performed. Two-dimensional (planar) velocity measurements were carried out in four planes with the aid of Laser Doppler Velocimetry (LDV). Computational Fluid Dynamics (CFD) analysis results for the scale model flowfleld are compared with the test data. The CFD results are in general agreement with the test data. The ability of the CFD methodology in identifying the global flow features (including critical points such as vortex, saddle point, etc.) has been demonstrated. Practical problems and difficulties associated with the LDV method applied to the complex geometry under consideration have been summarized.

Kandula, max↗
NASA NTRS1986

Summary of longitudinal stability and control parameters as determined from space shuttle Columbia flight test data

Extensive wind tunnel tests were conducted to establish the preflight aerodynamics of the Shuttle vehicle. This paper presents the longitudinal, short-period aerodynamics of the space shuttle Columbia as determined from flight test data. These flight-determined results are compared with the preflight predictions, and areas of agreement or disagreement are noted. In addition to the short-period aerodynamics, the pitch RCS effectiveness was determined.

Suit, W. T.↗
NASA NTRS1992

Numerical analyses of a rocket engine turbine and comparison with air test data

The study presents cold air test data on the Space Shuttle Main Engine High Pressure Fuel Turbopump turbine recently collected at the NASA Marshall Space Flight Center. Overall performance data, static pressures on the first- and second-stage nozzles, and static pressures along with the gas path at the hub and tip are gathered and compared with various (1D, quasi-3D, and 3D viscous) analysis procedures. The results of each level of analysis are compared to test data to demonstrate the range of applicability for each step in the design process of a turbine. One-dimensional performance prediction, quasi-3D loading prediction, 3D wall pressure distribution prediction, and 3D viscous wall pressure distribution prediction are illustrated.

Tran, Ken↗
NASA NTRS1986

Implementation and flight tests for the Digital Integrated Automatic Landing System (DIALS). Part 1: Flight software equations, flight test description and selected flight test data

Five flight tests of the Digital Automated Landing System (DIALS) were conducted on the Advanced Transport Operating Systems (ATOPS) Transportation Research Vehicle (TSRV) -- a modified Boeing 737 aircraft for advanced controls and displays research. These flight tests were conducted at NASA's Wallops Flight Center using the microwave landing system (MLS) installation on runway 22. This report describes the flight software equations of the DIALS which was designed using modern control theory direct-digital design methods and employed a constant gain Kalman filter. Selected flight test performance data is presented for localizer (runway centerline) capture and track at various intercept angles, for glideslope capture and track of 3, 4.5, and 5 degree glideslopes, for the decrab maneuver, and for the flare maneuver. Data is also presented to illustrate the system performance in the presence of cross, gust, and shear winds. The mean and standard deviation of the peak position errors for localizer capture were, respectively, 24 feet and 26 feet. For mild wind conditions, glideslope and localizer tracking position errors did not exceed, respectively, 5 and 20 feet. For gusty wind conditions (8 to 10 knots), these errors were, respectively, 10 and 30 feet. Ten hands off automatic lands were performed. The standard deviation of the touchdown position and velocity errors from the mean values were, respectively, 244 feet and 0.7 feet/sec.

Hueschen, R. M.↗
NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗
NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗
NASA NTRS1925

The application of propeller test data to design and performance calculations

This report is a study of a test data on a family of Durand's propellers (nos. 3, 7, 11, 82, 113, 139), which is fairly representative of conventional design. The test data are so plotted that the proper pitch and diameters for any given set of conditions are readily obtained. The same data are plotted in other forms which may be used for calculating performance when the ratio of pitch to diameter is known. These new plots supply a means for calculating the performance, at any altitude, of airplanes equipped with normal or supercharged engines. The coefficients used and the methods of plotting adopted in this report coordinate the results of a few tests into complete families of curves covering the entire range of p/d ordinarily used. This method of analyzing test data enables an investigator to plan tests systematically and leads to useful application of test data.

Diehl, Walter S↗
NASA NTRS1979

Program documentation for the space environment test division post-test data reduction program (GNFLEX)

The Space Environment Test Division Post-Test Data Reduction Program processes data from test history tapes generated on the Flexible Data System in the Space Environment Simulation Laboratory at the National Aeronautics and Space Administration/Lyndon B. Johnson Space Center. The program reads the tape's data base records to retrieve the item directory conversion file, the item capture file and the process link file to determine the active parameters. The desired parameter names are read in by lead cards after which the periodic data records are read to determine parameter data level changes. The data is considered to be compressed rather than full sample rate. Tabulations and/or a tape for generating plots may be output.

Jones, L. D.↗
NASA NTRS1938

A discussion of certain problems connected with the design of hulls of flying boats and the use of general test data

Report presents the results of a survey of problems encountered in applying general test data to the design of flying-boat hulls. It is shown how basic design features may be readily determined from special plots of test data. A study of the effect of the size of a flying boat on the probable limits to be covered by the general test data is included and recommendations for special tests and new methods of presenting test data for direct use in design are given.

Diehl, Walter S↗
NASA NTRS1985

An industry and government survey: A nickel-hydrogen testing data base

A survey of the testing data base for nickel-hydrogen (NiH2) battery cells was performed. The objective of this survey was to evaluate the status of testing of cells in general and of the Air Force design nickel-hydrogen cell in particular. Sufficient detail was sought so that a critical evaluation of the test results and of cell performance could be made. Realizing that subtle differences in test conditions can result in large differences in cell performance, an effort was made to define the actual test environment as closely as possible. These data were obtained in the time period February to May 1984, and reflect the status of tests at that time. Periodic updates of the information are planned. The testing data collected from most North American sources indicates that the basis for use of NiH2 cells in high orbits is firm. Results from over 227 cells produced only 14 failures up to 1000 cycles. The failures are of the type that have either been corrected or would be screened out in a flight program. Recent flight experience appears to support this position.

Badcock, C.↗
NASA NTRS1976

Correlation of low speed wind tunnel and flight test data for V/STOL aircraft

The availability of wind tunnel test data for correlation purposes of the same V/STOL aircraft tested in flight is very limited. This is due in a large part to size limitations of wind tunnels and the number of wind tunnels available for testing of full-scale aircraft. Wind tunnel tests are described for two research aircraft - the XV-5B fan-in-wing aircraft and the YOV-10 RCF (rotating cylinder flap) aircraft - in the NASA Ames 40- by 80-foot wind tunnel. The tests were conducted specifically to provide for correlation between wind tunnel and in-flight aerodynamics and noise test data. Correlation between aerodynamic and noise data are presented and testing techniques that are related to the accuracy of the data, or that might affect the correlations, are discussed. The correlation of noise measurements made with a J-85 engine mounted on a F-106 aircraft during low altitude flyovers with the same J-85 engine mounted on a model and tested in the Ames 40- by 80-foot wind tunnel are also reported.

Cook, W. L.↗
NASA NTRS2000

Identification of Low Order Equivalent System Models From Flight Test Data

Identification of low order equivalent system dynamic models from flight test data was studied. Inputs were pilot control deflections, and outputs were aircraft responses, so the models characterized the total aircraft response including bare airframe and flight control system. Theoretical investigations were conducted and related to results found in the literature. Low order equivalent system modeling techniques using output error and equation error parameter estimation in the frequency domain were developed and validated on simulation data. It was found that some common difficulties encountered in identifying closed loop low order equivalent system models from flight test data could be overcome using the developed techniques. Implications for data requirements and experiment design were discussed. The developed methods were demonstrated using realistic simulation cases, then applied to closed loop flight test data from the NASA F-18 High Alpha Research Vehicle.

Morelli, Eugene A.↗
DOE OSTI2016

Test Data Monitor

The National Security Campus (NSC) collects a large amount of test data used The National Security Campus (NSC) collects a large amount of test data used to accept high value and high rigor product. The data has been used historically to support root cause analysis when anomalies are detected in down-stream processes. The opportunity to use the data for predictive failure analysis however, had never been exploited. The primary goal of the Test Data Monitor (TDM) software is to provide automated capabilities to analyze data in near-real-time and report trends that foreshadow actual product failures. To date, the aerospace industry as a whole is challenged at utilizing collected data to the degree that modern technology allows. As a result of the innovation behind TDM, Honeywell is able to monitor millions of data points through a multitude of SPC algorithms continuously and autonomously so that our personnel resources can more efficiently and accurately direct their attention to suspect processes or features. TDM’s capabilities have been recognized by our U.S. Department of Energy National Nuclear Security Administration (NNSA) sponsor for potential use at other sites within the NNSA. This activity supports multiple initiatives including expectations of the NNSA and broader corporate goals that center around data-based quality controls on production.

Bosas, Joseph↗
NASA NTRS1978

Test data report, low speed wind tunnel tests of a full scale lift/cruise-fan inlet, with engine, at high angles of attack

A low speed wind tunnel test of a fixed lip inlet with engine, was performed. The inlet was close coupled to a Hamilton Standard 1.4 meter, variable pitch fan driven by a lycoming T55-L-11A engine. Tests were conducted with various combinations of inlet angle of attack freestream velocities, and fan airflows. Data were recorded to define the inlet airflow separation boundaries, performance characteristics, and fan blade stresses. The test model, installation, instrumentation, test, data reduction and final data are described.

Shain, W. M.↗
NASA NTRS1975

Test data from solid propellant plume aerodynamics test program in Ames 6 x 6 foot supersonic wind tunnel (shuttle test FA7) (Ames test 033-66)

The aerodynamic effects of plumes from hot combustion gases in the presence of a transonic external flow field were measured to advance plumes simulation technology, extend a previously acquired data base, and provide data to compare with the effects observed using cold gas plumes. A variety of underexpanded plumes issuing from the base of a strut-mounted ogive-cylinder body were produced by combusting solid propellant gas generators. The gas generator fired in a short-duration mode (200 to 300 msec). Propellants containing 16 percent and 2 percent A1 were used, with chamber pressures from 400 to 1800 psia. Conical nozzles of 15 deg half-angle were tested with area ratios of 4 and 8. Pressures were measured in the gas generator combustion chamber, along the nozzle wall, on the base, and along the body rear exterior. Schlieren photographs were taken for all tests. Test data are presented along with a description of the test setup and procedures.

Hair, L. M.↗
NASA NTRSDate not supplied

Py MILab: Capturing, Analyzing and Storing Test Data

Integrated Computational Materials Engineering (ICME) has recently received widespread attention due to its promises in reducing dependence on physical testing for engineering design by relying on simulation, reducing both time and cost to market for various applications. ICME however requires validated multiscale material models, which is heavily dependent on available test data with full material and test pedigree, including material processing, test and measurement equipment, raw data collection, and analysis methodology and results. Populating searchable information management systems with such rich data sets is often burdensome for data producers, resulting in a lack of findable data for modelers to validate and verify their models. To overcome these cultural barriers to ICME, NASA has developed of various database-integration toolsets that perform both data management activities within the organization’s best practices with additional functionality that relieves the effort of the data producer and promotes adoption of information management system. One such tool currently under development is Py MILab, an automatic framework for automatic capturing, analysis, maintenance, and storage of material test data. Py MILab uses a modular approach for capturing raw data, analyzing the data, and storing the data in a database, interfaced by neutral file structures, to promote plug-and-play capabilities for various analysis types. TMAnalysis is a Python-based tool that performs automatic data reduction and analysis of uniaxial thermomechanical test data. The TMAnalysis toolset can be implemented within the Analysis module of Py MILab, and thus requires a populated neutral file form the Raw Data Module of Py MILab and outputs a Analysis neutral file compatible with the Database Module of Py MILab. TMAnalysis is able to perform automatic segmentation of multistage tests and perform data analysis and reduction, including determination of point-wise properties in tension, compression, and shear, analysis of stress relaxation tests, creep analysis and zone identification, and combination of these stage types for tests with complex loading histories. The TMAnalysis code is accompanied with a graphical user interface (GUI) that allows users to easily analyze test data in bulk, verify the automatic, consistent analysis performed by the backend code, and edit stage segmentation if necessary before producing the output neutral files, ensuring data is properly analyzed and maintained with full traceability.

Data management↗
DOE OSTI2026

Downloadable Dynamometer Database (D3): Public Test Data on Advanced-Technology Vehicles

Access to high-quality, independent vehicle test data is critical to advancing energy-efficient transportation research. The Downloadable Dynamometer Database (D3) is a public repository of dynamometer test data on advanced-technology vehicles, generated at the Advanced Mobility Technology Laboratory (AMTL) at Argonne National Laboratory and hosted by the Transportation and Power Systems Division. The database has been made available to support researchers, students, and professionals engaged in energy-efficient vehicle research, development, and education. A wide range of vehicle categories has been tested (i.e., alternative fuel vehicles, conventional gasoline and diesel vehicles, all-electric vehicles, hybrid electric vehicles, and plug-in hybrid electric vehicles), as well as various drive cycles and test conditions documented in the accompanying D3 user presentation. Stakeholders can select a vehicle type, identify a vehicle of interest, and download the associated test data for use in their own analyses. Data downloaded from D3 must be accompanied by the required attribution: "This data is from the Downloadable Dynamometer Database and was generated at the Advanced Mobility Technology Laboratory (AMTL) at Argonne National Laboratory." These data are critical to vehicle modeling, validation, technology assessment, and educational use.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗