Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEMPERATURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

High Temperature / High Frequency Temperature Measurement: Achieving MHz Response at Temperatures > 1000 Deg-F

High frequency temperature measurements are not possible with current SOA temperature measurement devices at temperatures higher than ~700 deg-F. Temperature measurements above ~1000 deg-F are typical for entry vehicle thermal protection systems (TPS), rocket engines, ram/scramjet engines, etc. A new technology capable of achieving ~1200 deg-F temperature measurements with MHz response has been achieved. Investigations are underway to extend the concept to even higher temperatures. A U.S. patent application is about to be submitted.

High Frequency↗

High-temperature thermoelectric performance of heavily doped PbSe

We present a model calculation, employing first-principles calculations as well as empirical data, which suggests that properly hole-doped bulk PbSe may show a Seebeck coefficient as high as 230 μV/K, in a temperature regime in which the lattice thermal conductivity is rather small. It may therefore show a figure-of-merit ZT as high as 2 for temperatures of 1000 K. Heavily doped p-type PbSe may offer better thermoelectric performance than the sister material, optimized PbTe, for high-temperature applications such as power generation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the Interpretation and Correlation of High-Temperature Ignition Delays in Reactors with Varying Thermodynamic Conditions

Ignition delay time (IDT) is a useful global metric for fuel performance screening and a major target for kinetic modeling. Measurements of IDT are conceptually straightforward, however interpretation could be complicated, especially for systems with changing temperature and pressure. Some experimental conditions in the high repetition rate miniature shock tube (HRRST) exhibit complex temperature and pressure state histories. To better interpret and correlate IDTs, especially those obtained in reactors with varying thermodynamic conditions, an inverse Livengood-Wu (L-W) integral technique is applied to de-convolve the constant condition IDTs from measured IDTs in the HRRST using information on the varying state history. In this paper, the approximate problem is demonstrated using only the measured pressure history leading up to ignition, where the temperature history is estimated based on an isentropic assumption. The IDTs of several fuels were first measured in the HRRST including isooctane and acetone to represent those fuels without strong low temperature chemistry effects. Based on the measured pressure and approximated temperature history, measurements of IDTs in the HRRST compare very favorably with those measured using more conventional techniques, including conventionally sized shock tubes, via the inverse L-W correlation with relaxed Newton iteration and Genetic Algorithm (GA). Furthermore, this study demonstrates the feasibility of using a high throughput ignition testing facility, like the HRRST to extract the constant state IDT measured in regular shock tubes, assisted by the inverse L-W correlation. It is expected with an independent temperature measurement available in the future, IDTs in a broader range of thermodynamic conditions and effects of heat loss could be better resolved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Load partitioning between ferrite/martensite and dispersed nanoparticles of a 9Cr ferritic/martensitic (F/M) ODS steel at high temperatures

In this study, a high-energy synchrotron radiation X-ray technique was used to investigate the tensile deformation processes of a 9Cr-ODS ferritic/martensitic (F/M) steel at different temperatures. Two minor phases within the 9Cr-ODS F/M steel matrix were identified as Y2Ti2O7 and TiN by the high-energy X-ray diffraction, and confirmed by the analysis using energy dispersive X-ray spectroscopy (EDS) of scanning transmission electron microscope (STEM). The lattice strains of the matrix and particles were measured through the entire tensile deformation process. During the tensile tests, the lattice strains of the ferrite/martensite and the particles (TiN and Y2Ti2O7) showed a strong temperature dependence, decreasing with increasing temperature. Analysis of the internal stress at three temperatures showed that the load partitioning between the ferrite/martensite and the particles (TiN and Y2Ti2O7) was initiated during sample yielding and reached to a peak during sample necking. At three studied temperatures, the internal stress of minor phases (Y2Ti2O7 and TiN) was about 2 times that of F/M matrix at yielding position, while the internal stress of Y2Ti2O7 and TiN reached about 4.5-6 times and 3-3.5 times that of the F/M matrix at necking position, respectively. It indicates that the strengthening of the matrix is due to minor phases (Y2Ti2O7 and TiN), especially Y2Ti2O7 particles. Although the internal stresses of all phases decreased with increasing temperature from RT to 600 degrees C, the ratio of internal stresses of each phase at necking position stayed in a stable range (internal stresses of Y2Ti2O7 and TiN were about 4.5-6 times and 3-3.5 times of that of F/M matrix, respectively). The difference between internal stress of the F/M matrix and the applied stress at 600 degrees C is slightly lower than those at RI and 300 degrees C, indicating that the nanoparticles still have good strengthening effect at 600 degrees C. (C) 2015 Elsevier B.V. All rights reserved.

Microstructure↗

Evidence for strong enhancement of the magnetic ordering temperature of trivalent Nd metal under extreme pressure [Anomalous enhancement of the magnetic ordering temperature of trivalent Nd metal under extreme pressure: Possible Kondo lattice behavior]

Four-point electrical resistivity measurements were carried out on Nd metal and dilute magnetic alloys containing up to 1 at.% Nd in superconducting Y for temperatures 1.5–295 K under pressures to 210 GPa. The magnetic ordering temperature T o of Nd appears to rise steeply under pressure, increasing ninefold to 180 K at 70 GPa before falling rapidly. Y(Nd) alloys display both a resistivity minimum and superconducting pair breaking ΔT c as large as 38 K/at.% Nd. The present results give evidence that for pressures above 30–40 GPa, the exchange coupling J between Nd ions and conduction electrons becomes negative, thus activating Kondo physics in this highly correlated electron system. Furthermore, the rise and fall of T o and ΔT c with pressure can be accounted for in terms of an increase in the Kondo temperature.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

On the Use of Ocean Dynamic Temperature for Hurricane Intensity Forecasting

Sea surface temperature (SST) and the Tropical Cyclone Heat Potential (TCHP) are metrics used to incorporate the ocean's influence on hurricane intensification in the National Hurricane Center's Statistical Hurricane Intensity Prediction Scheme (SHIPS). While both SST and TCHP serve as useful measures of the upper-ocean heat content, they do not accurately represent ocean stratification effects. Here we show that replacing SST in the SHIPS framework with a dynamic temperature (Tdy), which accounts for the oceanic negative feedback to the hurricane's intensity arising from storm-induced vertical mixing and sea-surface cooling, improves the model performance. While the model with SST and TCHP explains nearly 41% of the variance in 36-hr intensity changes, replacing SST with Tdy increases the variance explained to nearly 44%. Our results suggest that representation of the oceanic feedback, even through relatively simple formulations such as Tdy, may improve the performance of statistical hurricane intensity prediction models such as SHIPS.

Balaguru, Karthik↗

Two-temperature model in molecular dynamics simulations of cascades in Ni-based alloys

In high-energy irradiation events, energy from the fast moving ion is transferred to the system via nuclear and electronic energy loss mechanisms. The nuclear energy loss results in the creation of point defects and clusters, while the energy transferred to the electrons results in the creation of high electronic temperatures, which can affect the damage evolution. We perform molecular dynamics simulations of 30 keV and 50 keV Ni ion cascades in nickel-based alloys without and with the electronic effects taken into account. We compare the results of classical molecular dynamics (MD) simulations, where the electronic effects are ignored, with results from simulations that include the electronic stopping only, as well as simulations where both the electronic stopping and the electron-phonon coupling are incorporated, as described by the two temperature model (2T-MD). Our results indicate that the 2T-MD leads to a smaller amount of damage, more isolated defects and smaller defect clusters.

Zarkadoula, Eva↗