SEARCH · Engineering Papers

Results for “Surface Comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Fermiology and transport properties of the candidate topological crystalline insulator SrAg 4 ⁢Sb 2

Compared to time-reversal symmetry-protected ℤ 2 topological insulators and Dirac/Weyl semimetals, there are significantly fewer candidates for topological crystalline insulators. SrAg 4 ⁢Sb 2 is predicted to exhibit topological crystalline insulator behavior when considering spin-orbit coupling. In this study, we systematically investigate single crystals of SrAg 4 ⁢Sb 2 using electrical transport and magnetic torque measurements, along with first-principles calculations. Our transport data reveals its compensated semimetal nature with a magnetoresistance up to around 700% at 2 K and 9 T. Analysis of de Haas–van Alphen oscillations uncovers a Fermi surface consisting of three distinct Fermi pockets with light effective masses. Comparison between the three-dimensional fermiology obtained from our oscillation data and the first-principles calculations demonstrates excellent agreement. This confirms the accuracy of the calculations, which indicate a band inversion centered at the 𝑇 point and identify the existence of nontrivial tube and needle hole Fermi pockets at Γ, alongside one trivial diamond electron pocket at the 𝐹 point in the Brillouin zone. Furthermore, symmetry and topology analysis results in two potential sets of topological invariants, suggesting the emergence of two-dimensional gapless Dirac surface states either on the 𝑎⁢𝑏 planes or on both the 𝑎⁢𝑏 planes and mirror planes, protected by crystal symmetries. Therefore, SrAg 4 ⁢Sb 2 emerges as a promising candidate topological crystalline insulator.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Single particle trace element analysis of uranium oxide standards with laser-induced breakdown spectroscopy

Femtosecond Laser-Induced Breakdown Spectroscopy (LIBS) was used to analyze over 1000 individual particles of uranium oxide trace element standard CRM124. Intra-granular analysis showed elemental concentrations were consistent across different surface locations on each uranium grain. However, inter-granular comparison revealed large heterogeneity between different grains of the same sample. By comparing the distribution of elemental concentrations across the particle populations, we were able to correctly identify a manufacturing process involving wet chemistry, rather than a dry mixing of two powders to give an overall chemical average. In conclusion, this demonstrates the utility of LIBS as a large-scale single particle analysis tool for nuclear forensics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Comprehensive new insights on the potential use of SiC as plasma-facing materials in future fusion reactors

Abstract The performance of silicon carbide as an alternative plasma facing material (PFM) was studied at various irradiation conditions relevant to ion energies and fluxes of a fusion reactor. This analysis involves detailed modeling of subsurface plasma/material interactions, sputtered particle transport above the surface and redeposition, and related changes in material composition and microstructure induced by steady-state and Edge Localized Mode ion fluxes. Transition of a crystalline SiC surface to semi-crystalline and amorphous phases was analyzed based on advanced modeling of DIII-D tokamak experiments where SiC was irradiated in single- and multiple- L-mode and H-mode discharges. This analysis shows that displacement damage, particle deposition/redeposition, and D accumulation on the SiC divertor surface can lead to significant microstructural changes that result in enhanced sputtering erosion in comparison with the original crystalline material. However, the resulting total net erosion rate for a full-coverage, advanced tokamak, SiC coated divertor may well be acceptably low. Moreover, the C sputtering yield from the evolved SiC surface can be seven times lower than from a pure graphite surface; this would imply significantly reduced tritium co-deposition rates in a D-T tokamak reactor, compared with a pure carbon surface. It was also determined that chemical sputtering of both C and Si should not result in any noticeable effect on the net erosion, for attached plasma regimes. Our results thus show encouraging results overall for use of SiC as a PFM in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Laser interference structuring of Cu for adhesive joining of HVAC equipment

Due to potential energy and cost savings benefits, adhesive joining has been recently considered for heating, ventilation, air conditioning, and refrigeration (HVAC&R) systems. HVAC adhesive bonding requires cost-effective and adequate surface preparations of adherents. Here, this article investigates the use of abrasion, traditional single-beam laser, and a laser-interference technique as surface preparations of copper surfaces. Surface morphology is characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Effective submicrometer peak-to-valley structuring with a periodicity of ∼2.7μ⁢m was demonstrated for laser-interference processing. Single-lap shear tests were conducted for 89 joints made with bondline thicknesses of 0.15 and 0.3 mm. Data on process variables and measured variables included open-time, bond length, maximum load, displacement at failure, shear lap strength, and failure mode. A statistical analysis was conducted on each lot to determine the lower limit with 95% confidence intervals for displacements at failure and shear lap strengths. A comparison is presented between the properties of laser-structured joints with respect to those prepared by abrasion, which is considered the baseline surface preparation technique. Based on this comparison, one single-beam laser technique and two laser-interference techniques were shown to exhibit vastly superior performance over the joints made with abraded specimens.

Sabau, Adrian S. [Oak Ridge National Laboratory (O↗

DOE OSTI2024

Distilling the Evolving Contributions of Anthropogenic Aerosols and Greenhouse Gases to Large‐Scale Low‐Frequency Surface Ocean Changes Over the Past Century

Abstract Anthropogenic aerosols (AER) and greenhouse gases (GHG)—the leading drivers of the forced historical change—produce different large‐scale climate response patterns, with correlations trending from negative to positive over the past century. To understand what caused the time‐evolving comparison between GHG and AER response patterns, we apply a low‐frequency component analysis to historical surface ocean changes from CESM1 single‐forcing large‐ensemble simulations. While GHG response is characterized by its first leading mode, AER response consists of two distinct modes. The first one, featuring long‐term global AER increase and global cooling, opposes GHG response patterns up to the mid‐twentieth century. The second one, featuring multidecadal variations in AER distributions and interhemispheric asymmetric surface ocean changes, appears to reinforce the GHG warming effect over recent decades. AER thus can have both competing and synergistic effects with GHG as their emissions change temporally and spatially.

Dong, Yue↗

DOE OSTI2025

U-Surf: a global 1 km spatially continuous urban surface property dataset for kilometer-scale urban-resolving Earth system modeling

High-resolution urban climate modeling has faced substantial challenges due to the absence of a globally consistent, spatially continuous, and accurate dataset to represent the spatial heterogeneity of urban surfaces and their biophysical properties. This deficiency has long obstructed the development of urban-resolving Earth system models (ESMs) and ultra-high-resolution urban climate modeling, over large domains. Here, we present U-Surf, a first-of-its-kind 1 km resolution present-day (circa 2020) global continuous urban surface parameter dataset. Using the urban canopy model (UCM) in the Community Earth System Model as a base model for satisfying dataset requirements, U-Surf leverages the latest advances in remote sensing, machine learning, and cloud computing to provide the most relevant urban surface biophysical parameters, including radiative, morphological, and thermal properties, for UCMs at the facet and canopy level. Generated using a systematically unified workflow, U-Surf ensures internal consistency among key parameters, making it the first globally coherent urban canopy surface dataset. U-Surf significantly improves the representation of the urban land heterogeneity both within and across cities globally; provides essential, high-fidelity surface biophysical constraints to urban-resolving ESMs; enables detailed city-to-city comparisons across the globe; and supports next-generation kilometer-resolution Earth system modeling across scales. U-Surf parameters can be easily converted or adapted to various types of UCMs, such as those embedded in weather and regional climate models, as well as air quality models. The fundamental urban surface constraints provided by U-Surf can also be used as features for machine learning models and can have other broad-scale applications for socioeconomic, public health, and urban planning contexts. We expect U-Surf to advance the research frontier of urban system science, climate-sensitive urban design, and coupled human–Earth systems in the future. The dataset is publicly available at https://doi.org/10.5281/zenodo.11247598 (Cheng et al., 2024).

Cheng, Yifan [Univ. of Illinois at Urbana-Champaig↗

DOE OSTI2024

Quantifying Dissolution Dynamics in Porous Media Using a Spatial Flow Focusing Profile

Abstract The diverse range of patterns in porous media formed by dissolution processes depends on the relative magnitude of flow, transport, and chemical reactions at pore surfaces. However, distinguishing between regimes often relies solely on qualitative, visual comparisons of emergent structures. Here, we propose a quantitative measure capable of identifying different regimes using the concept of the spatial flow focusing profile, which segments the medium into cross sections along the flow direction to calculate the flow focusing index for each section. We employ this measure in numerical simulations of a dissolving porous medium using a pore network model. We obtain a morphological phase diagram of dissolution patterns, which we characterize using the flow focusing profile. In particular, we demonstrate that analyzing the temporal changes in the profile allows one to quantitatively distinguish between wormholing and channeling. The transition between them is shown to be affected by the heterogeneity of the system.

58 GEOSCIENCES↗

DOE OSTI2024

Performance evaluation of the USGS velocity model for the San Francisco Bay Area

In this study, we evaluated the performance of the United States Geological Survey velocity model developed for the San Francisco Bay Area (SFBA), version 21.1. The evaluation was performed through high-resolution three-dimensional physics-based ground motion simulations of seven small-magnitude earthquakes (ranging from magnitude 3.8 to 4.4) that occurred on the eastern side of the San Francisco Bay. The simulations were performed in the frequency range from 0 to 5 Hz with a minimum shear-wave velocity of 250 m/s, which allowed the capture of wave propagation effects of the near-surface soft materials that characterize local basins. Based on the direct comparison of Fourier amplitude spectra between recorded and simulated ground motions for more than 250 stations, we found that the velocity model generally performs well in the frequency range of 0.2–5 Hz. The median value of the Fourier amplitude residuals was found to be near zero for all seven earthquakes. The slight over-prediction of 0.2 log-natural units at frequencies above 3 Hz in our simulations was attributed to the potentially inaccurate representation of the source radiation pattern by a double-couple point source model, and simple representation of shallow small-scale underground structural complexity in the velocity model. Maps of spectral amplitude differences between the simulated and recorded data were used to identify areas responsible for systematic ground motion over-predictions or under-predictions. For example, while some sub-domains over soft sediments show over-prediction patterns, the block east of the Hayward fault is prone to exhibit patterns of under-prediction. These maps can be used to guide future refinements of the SFBA velocity model. Since our simulation methodology allows for the decoupling of the source and wave propagation effects, the ground motion data generated by our simulations can also be used to quantify the epistemic uncertainty due to the velocity model, in empirically based ground motion estimates for the SFBA.

58 GEOSCIENCES↗

DOE OSTI2026

Seismic Elastic Double-Beam Characterization of Faults and Fractures for CO₂ Storage Site Selection

Site characterization for underground injection and storage of gigatonne-scale CO₂ requires reliable and cost-effective methods to detect and characterize faults and fractures and to assess their stress state and fault activation potential. This is critical, as wastewater injection and disposal have been shown to activate faults and induce earthquakes, and CO₂ leakage remains a key concern for long-term storage. In this project, we developed seismic methods to detect and characterize large-scale sedimentary and crystalline basement faults and associated small-scale fractures below conventional seismic imaging resolution using multicomponent (9C) surface seismic data. Machine learning was used to automatically interpret large-scale faults, providing key information for estimating the maximum magnitude of potential induced earthquakes. High-fidelity imaging was achieved by exploiting redundancy across multiple elastic wave modes, where independent images from different modes and frequencies cross-validate each other. We also used our nonlinear signal comparison (NLSC) method for ground roll removal, improving data quality in complex near-surface conditions. The methods were validated using field data acquired in central Montana. Results show that basement faults extend into the sedimentary section and that small-scale fractures are widespread above the basement. The inferred stress orientation is consistent with regional stress data, and the estimated maximum induced earthquake magnitude is small (Mw ~2.3). The developed workflow provides a practical approach for fault and fracture characterization and for assessing induced seismicity and leakage risk. It is directly applicable to CO₂ storage site selection and to other subsurface systems.

02 PETROLEUM↗

DOE OSTI2024

Synchronization of the Recent Decline of East African Long Rains and Northwestern Eurasian Warming

Abstract The East African March–April–May (MAM, “long rains”) precipitation decline in recent decades remains a puzzle marked by various proposed large‐scale drivers. Here, the interannual variability of the long rains and their recent drying trend are examined using global model simulations and observations. Comparison of a control simulation and re‐initialized simulations in which land‐surface feedback is suppressed shows that much of the long rains deficit experienced between 1980 and 2014 is synchronized with the warming of the Northwestern Eurasian landmass. In agreement with the modeling results, multiple observational data sets reveal a strong negative correlation between MAM mean East African rainfall amount and the surface temperature over Northwestern Eurasia. Idealized simulations further indicate that warming in Northwestern Eurasia weakens the regional Hadley Cell and diverts the monsoonal transport of moisture away from Eastern Africa toward Europe and southern Africa, highlighting the role of remote land surface warming on the observed precipitation decline.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Analysis of Tank 38H (HTF-38-24-53, -56) and Tank 43H (HTF-43-24-54, -55) Samples for Support of the Enrichment Control and Corrosion Control Programs

Savannah River National Laboratory analyzed samples from Tank 38H and Tank 43H to support the Enrichment Control Program (ECP) and Corrosion Control Program (CCP). The results indicate the concentrations of most soluble species in the Tank 38H surface sample increased from the previous Tank 38H surface sample. The current Tank 38H subsurface sample shows similar Na, free hydroxide, and anions in comparison to the previous subsurface sample. However, the 38H subsurface sample shows lower concentrations of Al, Ca, Fe, Mn, and Si in comparison to the previous Tank 38H subsurface sample. Measurement of the wt.% insoluble solids in the Tank 38H subsurface sample and associated uncertainty analysis indicates that the calculated average wt.% insoluble solids is 0.45 ± 0.75 wt.%. Significant differences in the concentrations of major components between the Tank 38H surface and subsurface samples indicate significant stratification of solution species between these two locations within Tank 38H.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Analysis of Tank 38H (HTF-38-25-36, -32) and Tank 43H (HTF-43-25-33, -35) Samples for Support of the Enrichment Control and Corrosion Control Programs

Savannah River National Laboratory (SRNL) analyzed samples from Tank 38H and Tank 43H to support the Enrichment Control Program (ECP) and Corrosion Control Program (CCP). The results indicate the concentrations of most soluble species in the Tank 38H surface sample are similar to the previous Tank 38H surface sample. The current Tank 38H subsurface sample shows similar Na, free hydroxide, and anions in comparison to the previous subsurface sample. The current Tank 38H subsurface sample appears brown in color. Measurement of the wt.% insoluble solids in the Tank 38H subsurface sample and associated uncertainty analysis indicates that the calculated average wt.% insoluble solids is 5.5 ± 3.6 wt.%. Significant differences in the concentrations of major components between the Tank 38H surface and subsurface samples indicate stratification of solution species between these two locations within the Tank 38H. The current Tank 43H surface sample is ~ 10% diluted versus the previous Tank 43H surface sample and the Tank 43H subsurface sample is similar in composition to the previous Tank 43H subsurface sample. Information provided by SRMC on tank additions since the last ECP sampling indicates that a total of about 4,062 gallons of water was added to Tank 43H. This addition could account for the observed relatively small dilution of ~ 10% in the Tank 43H surface sample. Similar solution compositions measured in the current Tank 43H surface and subsurface samples indicate a minimal stratification within the tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Photon counting with intensified charge coupled device (ICCD) – I. In-depth detector characterization

While the adsorption properties of transition metal catalysts have been widely studied, leading to the discovery of various scaling relations, descriptors of catalytic activity, and well-established computational models, a similar understanding of semiconductor catalysts has not yet been achieved. In this work, we present a high-throughput density functional theory investigation into the adsorption properties of 5 oxides of interest to the photocatalytic CO 2 reduction reaction: TiO 2 (rutile and anatase), SrTiO 3 , NaTaO 3 , and CeO 2 . Using a systematic approach, we exhaustively identify unique surfaces and construct adsorption structures to undergo geometry optimizations. We then perform a data-driven analysis, which reveals the presence of weak adsorption energy scaling relations, the propensity of adsorbates of interest to interact with oxygen surface sites, and the importance of slab deformation upon adsorption. Our findings are presented in the context of experimental observations and in comparison to previously studied classes of catalysts, such as pure metals and tellurium-containing semiconductors, and reinforce the need for a comprehensive approach to the study of site-specific surface phenomena on semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Systematic computational study of oxide adsorption properties for applications in photocatalytic CO 2 reduction

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

In-Situ Laser Diagnostics to Understand Plasma-Surface Interactions in Titanium Thin Film Deposition

During the current project period the following tasks were completed: (1) We demonstrated the feasibility of a new way of measuring CH3 radicals in a plasma environment using a single, femtosecond (fs) pulsed laser for the first time, in a CH4 + Ar flow. A single fs pulsed Ti:Sa laser was split into two beams and with beam conversion using crystals we generatedtwo beams of 275 nm and 205 nm. The 275 nm was used to predissociate the CH3 radicals to CH2+H, followed by 205 nm Two Photon Laser Induced Fluorescence (TALIF) detection of H atoms, with a 11 ns delay from 275 nm predissociation pulse. (2) We demonstrated preliminary CH3 concentration measurements with spatial (< 100 µm) and time resolution (< 10 ns) by image processing of H and Kr TALIF signal images. (3) The methodology to quantify CH3 concentrations was developed. (4) Preliminary measurements of laser dissociation cross sections for CH4 and CH3 to (CH3+H), and (CH2+H), respectively, were conducted. (5) 275 nm laser dissociation of CH4 is a multiphoton process, and the CH4 dissociation cross section is a more sensitive function of the laser pulse energy than CH4 concentration. In the coming months, we will make more precise measurements of the dissociation cross sections, 𝑘275, 𝐶𝐻4 and 𝑘275, 𝐶𝐻3, by varying the laser energy while keeping the flow composition and conditions constant. This will enable more precise quantification of CH3 radical concentrations. More detailed measurements of CH3 radicals will be conducted in the following months of 2025 (Sept-Dec) in a Titanium Isopropoxide (TIP) + H2 + Ar flow meant for pure phase Ti thin film deposition by Chemical Vapor Deposition (CVD). More precise measurements of 275 nm laser dissociation cross sections for CH4 (to CH3 + H) and CH3 (to CH2 + H) will be conducted in the future. Detailed 275 nm laser predissociation cross sections for CH4 and CH3 dissociation to (CH3+H), and (CH2+H), respectively, as a function of gas heating, plasma power, and laser pulse energy will be evaluated. This will enable quantification of CH3 concentrations in the precursor flow over a substrate with time and spatial resolution. Comparison of the concentrations with 2D numerical simulations can lead to understanding of plasma surface interactions during pure metallic Ti thin film deposition using environmentally safer non-halogen TIP precursor. Flow conditions for pure Ti thin film deposition using non-halogen precursor (TIP) will be identified in the following months.

Uddi, Mruthunjaya [Advanced Cooling Technologies, ↗

DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗

DOE OSTI2026

The XPS of Azines: A Comparative Study

A detailed analysis is presented of the X-ray Photoelectron Spectroscopy, XPS, of thin films of three Azines: Pyrazine, Pyridine and Pyrimidine. This includes not only the binding energies of the various core ionizations but also their intensities. A major focus is to compare our theoretical predictions with our measured XPS for N(1s) and C(1s) as a basis for assigning the features and for justifying the broadening parameters that must be applied to the theoretical results. The C(1s) XPS of Pyridine and Pyrimidine are significantly broadened because of unresolved XPS for their inequivalent C atoms. The extent of the binding energy, BE, shifts and the XPS intensities for the unique C atoms, which are responsible for this broadening, are obtained from the theory. The additional broadening parameters to be applied to the theory to enable comparison with measured XPS are discussed in terms of lifetime broadening, experimental resolution, and BE shifts in different layers of the thin film. A novel feature of our analysis is that it is necessary to invoke surface core level shifts to explain and to justify the broadenings needed to apply to the theoretical results to have a complete comparison with the measured XPS. The results presented have general value for extracting chemical and physical information from XPS.

Bagus, Paul↗

DOE OSTI2026

SPARTAN and IMPROVE Comparison Experiment (SPICE) Interim Campaign Report

SPICE (the SPARTAN and IMPROVE Comparison Experiment) aims to obtain and quantify comparisons between aerosol PM 2.5 mass concentration measurements from the University of Oklahoma (OU) Surface Particulate Matter Network (SPARTAN) station and the U.S. Environmental Protection Agency (EPA) Interagency Monitoring of Protected Visual Environments (IMPROVE) station hosted by the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) User Facility at ARM’s Southern Great Plains (SGP) observatory in Oklahoma. Aerosols—both natural and anthropogenic—affect human populations in multiple ways. Much of ARM’s research focuses on how aerosols influence weather and climate through their optical and radiative effects, as well as their impacts on clouds and precipitation. However, aerosols also pose direct risks to humans and other organisms through inhalation, with the severity of health impacts depending on particle size, chemical composition, and duration of exposure. The IMPROVE network was established by the U.S. EPA to monitor air quality, including visible clarity as well as total and chemically speciated aerosol mass concentrations. The ARM SGP site hosts the IMPROVE SOGP station. Separately, the SPARTAN network operates a globally distributed set of stations similar to IMPROVE but with an emphasis on remote deployment and semi-autonomous operation for use beyond the borders of the United States (IMPROVE only operates within the U.S.). The University of Oklahoma operates a SPARTAN station. To establish confidence in the OU SPARTAN instrumentation and measurement protocol relative to the EPA-certified IMPROVE station, the OU SPARTAN station is currently deployed at SGP in close proximity to the IMPROVE SOGP station. The SPICE campaign was envisioned as a contiguous calendar-year effort for 2025 to capture seasonal variation in mass loading as well as composition. However, independent of the SPICE campaign, the SPARTAN network adopted a new filter construction part-way through the year, interrupting our contiguous data set. Thus, to obtain a contiguous data set with a uniform consistent configuration, SPICE desires an extension through 2026.

54 ENVIRONMENTAL SCIENCES↗