SEARCH · Engineering Papers

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Preliminary Procedures and Acceptance Criteria for in-situ Structural Materials Surveillance for MSR

This report describes the initial development of the technical basis for a materials surveillance technology that, when fully developed and validated, can be used by stakeholders to develop and implement a materials surveillance program to manage materials degradation during reactor operations. The procedures described in this report aim to bound the detrimental effects of the reactor environment on the creep-fatigue life of the reactor components through materials surveillance. Specifically, the report describes procedures for selecting critical locations within the reactor components for surrogate materials surveillance and the sizing and placements of passively-actuated materials surveillance test articles under development by the US Department of Energy, Advanced Reactor Technologies Program. These test articles apply cyclic thermomechanical load to a surrogate sample of the component structural material passively through thermal expansion mismatch within the articles, without requiring any penetrations in the reactor coolant boundary. The procedures can be used to size materials surveillance test articles so that they will fail before the corresponding structural component. These articles would be exposed to the component operating environment, located to experience a bounding radiation fluence and representative coolant exposure. They can be monitored during reactor operations to ensure that they have not failed under the combination of creep-fatigue damage and environmental degradation. The report describes the key technical decisions and the corresponding rational for using these procedures to provide advanced warning of any impending material failure. An appendix describes the technical basis and the procedure for sizing a family of passively-actuated test articles. Finally, the report describes future work needed to complete the technical basis underlying this materials surveillance technology.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Assessment of Aging Degradation Mechanisms of Alloy 709 for Sodium Fast Reactors

This project was initiated in October 2015 to investigate the creep and creep-fatigue behavior of Alloy 709 for structural components in Gen IV sodium cooled fast spectrum reactors. The goal of this project is to develop an understanding of the mechanisms responsible for the behavior of austenitic stainless steel alloy 709 under accelerated testing conditions to confidently predict long term creep and creep-fatigue behavior at the times (500,000 hours) and temperatures (550°C) of interest for fast reactor structural applications. Alloy 709 has exhibited significantly better creep resistance than Alloy 316H, which is currently specified in design of fast reactor structural components. However, the alloy has not been code qualified for elevated temperature nuclear design. The elevated temperature microstructure stability and creep and creep-fatigue behavior need to be better understood so service life can be accurately predicted. Alloy 709 was developed for fossil boiler applications, which operate at a higher temperature than the nuclear components. Thus, there is a strong need to characterize its creep and creep-fatigue behavior at these lower temperatures and corresponding longer service lifetimes. The overall objective of this project is to develop sufficient understanding of the mechanisms responsible for behavior of Alloy 709 under accelerated testing conditions to confidently predict long term creep and creep-fatigue behavior at the times (500,000 hours) and temperatures (550°C) of interest for fast reactor structural applications. The following report summarizes the findings of the creep-fatigue and creep behavior with respect to the research questions identified during the course of the project. Additionally, the training and professional development that occurred through the project and the products resulting from the project are summarized.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Draft Rules for Alloy 617 Creep-Fatigue Design Using an EPP+SMT Approach

The report describes an improved new creep-fatigue design method for structural components in high temperature nuclear service. The new method uses an integrated elastic-perfectly plastic (EPP) analysis and Simplified Model Test (SMT) approach that greatly simplifies the design process by avoiding the separate evaluation of creep and fatigue damages and eliminating the requirement of stress classification. The report includes draft design rules, presented in a format compatible with an ASME nuclear Code Case, as well as a commentary on the rules and the validation of the rules using pressurized SMT (p-SMT) test data. Areas of potential improvement have been identified for further evaluation. The report also develops EPP+SMT design charts for Alloy 617 at temperatures between 800°C and 950°C by extrapolating high strain range, short hold test data to low strain range and long hold times, typical for structural components in high temperature nuclear service. The design charts are currently limited to 10,000 cycles to avoid excessive extrapolation outside the test database. More robust alternate extrapolation procedures will be considered in future work. The report includes several verification problems comparing the new EPP+SMT design method with current ASME creep-fatigue design methods. The comparison demonstrates that the EPP+SMT method significantly reduces the over-conservatism in current methods. Finally, the report includes a fully-documented sample problem with multiple load cases detailing the application of proposed EPP+SMT design rules.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Simulation and Analysis on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) under SBLOCA scenario by using Cardinal to support the fracture mechanics analyses

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended durations or under accident condition. As one of the most significant components of a Reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Ageing degradation mechanisms (e.g. thermos-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The multi-physics simulations are performed using Cardinal, a wrapping of the GPU-oriented spectral element Computational Fluid Dynamics (CFD) code NekRS and other multi-physics sub-modules within the MOOSE framework. Cardinal now fully supports MOOSE stochastic perturbations of NekRS models with varying boundary conditions, initial conditions, material properties, and any other quantity which is defined by a kernel (such as coefficients in a momentum source model). The implementation is designed in a flexible manner so that scalar values are sent from MOOSE into a user scratch space in NekRS, which can then be applied for any purpose within the NekRS case files (both on the host and device). When modeling PTS, several factors can impact the results significantly. In this report, the impacts of the geometry of the model, Reynolds number and buoyancy effect are investigated. Two geometry, i.e., a simplified model and a realistic RPV model, with both laminar and turbulent flow condition are adopted for the PTS simulation with and without buoyancy effect. The purpose of the investigation is to understand the impact of these factors on the prediction of temperature history of RPV. The accurate prediction on the temperature evolution, which will be exported to Grizzly code for further analyses on the progression of aging mechanisms and their effects on the integrity of RPV structures, is very crucial. Based on the understanding of these factors, a more sophisticated model is built to analysis the PTS under SBLOCA scenario. A literature survey is conducted to pick the SBLOCA scenario for the multi-physics simulation. The analysis helps to explain the form and the transformation of the cold plum when the ECC is activated under SBLOCA. This model can be can be applied to study the PTS effect for different RPV configurations. The results can help to assess structural component degradation for advanced reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Understanding the local structure of disordered carbons from cellulose and lignin

An electron microscopy investigation was performed to understand the relationship between the microstructure and properties of carbonized cellulose and lignin (softwood kraft lignin) relative to the structure of the original biomass components. Structure details at micro- and molecular levels were investigated by scanning transmission electron microscopy. Atomic-resolution images revealed the presence of random disordered carbon in carbonized cellulose (C-CNC) and of large domains of well-ordered carbon with graphite sheet structure in carbonized lignin (C-Lignin). These structural differences explain why C-CNC exhibits higher surface area and porosity than C-Lignin. The presence of certain well-ordered carbon in carbonized lignin indicates some of the carbon in lignin are graphitized with heat treatment temperature up to 950 °C. This result is encouraging for future endeavors of attaining acceptable modulus of carbon fiber from lignin given suitable modifications to the chemistry and structure of lignin. The results of this research contribute to an improved understanding of the carbonization mechanism of the key cellulose and lignin components of biomass materials.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Glassy embedded solid-state electrode assemblies, solid-state batteries and methods of making electrode assemblies and solid-state batteries

Batteries, component structures and manufacturing methods, in particular including a glassy embedded battery electrode assembly having a composite material structure composed of interpenetrating material components including a porous electroactive network including a solid electroactive material, and a continuous glassy medium including a Li ion conducting sulfide glass, can achieve enhanced power output, reduced charging time and/or improved cycle life.

Visco, Steven J.↗

DOE OSTI2025

Electromagnetic Analysis of ITER Electron Cyclotron Emission Components and Support Structures for the Preliminary Design Review

The ITER electron cyclotron emission (ECE) diagnostic system is located at Design Shield Module (DSM) 2, Equatorial Port (EP) 9 to measure electron temperature profile and electron temperature fluctuations and also to assess nonthermal electron distributions via the oblique view. Therefore, ECE has both radial and oblique views with two couples of mirrors for two different optical views. This ECE diagnostic system shall be exposed to significant power due to unabsorbed electron cyclotron heating power in the plasma. It shall also receive large electromagnetic (EM) loads up to 100 MN/m 3 force density due to the eddy currents generated by the short 16-ms transient plasma disruption. The global EM models of EP12 and EP11 with the worst case of plasma disruption Major Disruption Downward Exponential 16 ms Category III (MD_DW_EXP16MS_CATIII) have been provided by ITER. However, the support structure for these critical components, including four mirrors, is still under the design and development phase, especially during the period of preliminary design reviews (PDRs). For those small in-vessel components that are not modeled explicitly for the PDRs, we can extract the magnetic field (B) data and flux variations (dB/dt) at those locations from the global model and then use the B and dB/dt method to calculate the eddy currents, EM forces, and torques on those components in the local submodels. In conclusion, this paper will present the detailed PDR EM analysis results of the ECE components and support structures.

Electromagnetic↗

DOE OSTI2026

Additive Manufacturing of Cryogenic Austenitic Steel JK2LB via Wire-Fed Directed Energy Deposition (DED) for Fusion Energy Applications

This study explores the feasibility of fabricating cryogenic austenitic steel JK2LB via both laser-based directed energy deposition (laser-DED) and arc-based directed energy deposition (arc-DED) additive manufacturing processes for potential application in fusion reactors. JK2LB, a low-nickel, high-manganese stainless steel developed for ITER, offers excellent cryogenic toughness, radiation resistance, and decay-to-clearance characteristics. Although JK2LB was originally designed to endure cyclic stresses at cryogenic temperatures in tokamaks, its low-temperature mechanical integrity and radiation tolerance also make it a promising candidate for structural components, such as the coil case/support structure in nonplanar high-temperature superconducting magnet assemblies in stellarators. Directed energy deposition (DED) additive manufacturing was selected for this study due to its capability to fabricate large structures with complex geometries. Here, to address the long lead time and high cost associated with acquiring conventional JK2LB solid wire, JK2LB powder-cored wire was developed as the feedstock material. Testing blocks were then fabricated using both wire-fed laser-DED and arc-DED processes. Microstructural and compositional analyses revealed that both DED approaches yield fully austenitic phase and columnar grain structures. Mechanical testing at room temperature revealed that both DED routes achieved yield strength and elongation comparable to those of conventionally processed JK2LB via vacuum melting, electroslag remelting, extrusion, and drawing, though ultimate tensile strength was reduced due to Mn loss and large columnar grains. As a study mainly focusing on the additive manufacturing process, this work demonstrates the potential of additive manufacturing for fusion energy applications and provides a basis for optimization and future cryogenic mechanical evaluation.

Cryogenic steel↗

DOE OSTI2020

Evaluation of Hydrogen Generation in High Burnup Demonstration Dry Storage Cask

This report provides a best-estimate evaluation of residual water content (post-dry out) in the High Burnup (HBU) LWR Spent Fuel Demonstration project TN-32 cask, and evaluates the radiolysis of the residual free water, and the physisorbed and chemisorbed waters on the surfaces of the fuel and cask internal contents. The evaluation of radiolytic breakdown of those waters with gamma radiation causing the generation of hydrogen gas (H 2 ) is made using available literature data and models. This evaluation is part of the overall materials performance evaluation of the SNF-in-canister system, and is part of the technical bases for their continued safe dry storage. The TN-32 cask contents included 32 HBU LWR spent fuel assemblies each with 264 fuel rods clad in zirconium alloys, aluminum neutron absorber components, and aluminum and stainless steel structural components. The residual free and surface (physisorbed/chemisorbed) waters are ascribed to water vapor in the free volume and to components’ surfaces, respectively. The total potential radiolytic hydrogen inventory from the water vapor and from waters ascribed to surfaces has been calculated assuming all the water produced molecular H 2 . The residual water that is chemically incorporated into the bulk of a hydrated oxide, i.e., chemisorbed water, and its total potential hydrogen inventory has been calculated. These calculations are at the physical limit of material available and are used for a bounding assessment purpose only.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Criticality Analysis of Wind Turbine Components - Intern Poster [Poster]

Wind turbines are an important part of critical energy infrastructure, with wind farms generating more than 10% of US energy in 2023. The goal of this project is to identify and analyze major, common components of wind turbines to reach a preliminary understanding of which should be considered most critical in terms of turbine operation and attack surface. At the time of this project, minimal data was available regarding component costs and lead times, so a qualitative risk assessment approach was used. Components were given a score of 1-5 in four categories– cost to repair, operational downtime, ease of physical attack, and ease of cyber attack. An overall component criticality score was assigned based on the sum of those scores, with a higher score indicating higher criticality. The turbine control system was identified as the most critical component, closely followed by the blades, structural components, and gearbox. This is ongoing project, and further research on the supply chain for wind turbine components will allow for a deeper and more concrete understanding of component criticality.

17 WIND ENERGY↗

DOE OSTI2023

GRAPHITE–MOLTEN SALT CONSIDERATIONS FOR COMPONENTS IN NUCLEAR APPLICATIONS

The new High Temperature Reactor (HTR) designs being considered for future Gen IV nuclear reactor deployment include designs utilizing molten salt as the primary coolant. These molten-salt cooled, graphite core designs pose new material compatibility challenges that are not considered within the gas-cooled HTR designs that have been previously built and operated. While the Molten Salt Reactor Experiment (MSRE) demonstrated that the molten salt can be considered chemically inert to graphite the novel physical and thermal interactions that the molten salt poses may be just as impactful as the chemical reactivity. Specifically, molten salt intrusion into the open pore structure of nuclear graphite grades can provide additional internal stresses within the microstructure exacerbating the stress buildup from irradiation induced dimensional change. Additionally, designs using a molten salt containing liquid fuel could provide “hot spots” within graphite structural components causing local thermal stresses. Abrasion and erosion concerns are magnified with molten salt due to the extremely high density of the salts (some have higher densities than the structural graphite components). Finally, the graphite-graphite and fuel pebble-graphite tribological behavior are distinctly difference within the molten salt from the inert gas environments and must be investigated. These topics and others are currently under investigation within the DOE Advanced Reactor Technologies (ART) graphite program and will be discussed in depth.

Gallego, Nidia↗

DOE OSTI2021

Demonstration of CFD to support the coupled analysis of a reactor pressure vessel subjected to pressurized thermal shock

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Multi physics simulation on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) by using Cardinal

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Thermal-Fluid and Thermal-Structural Response of the T-Tube Modular Divertor to Spatiotemporally Varying Heat Loads

Tungsten (W) is the leading candidate for divertor target plates because of its high melting point (>3000°C), thermal conductivity, and ultimate tensile stress. While W and its alloys are the only solid materials that can survive the high heat fluxes incident on the divertor, W’s low-ductility high ductile-to-brittle transition temperature of ~600°C and relatively low recrystallization temperature (RT) of ~1300°C pose structural (among other) challenges. The objective of this work is to estimate the thermal-fluid and thermal-structural performance of the helium (He)-cooled T-tube divertor, which was originally developed by the Advanced Reactor Innovation and Evaluation Study (ARIES) using numerical simulations. Here, predictions of temperature distributions across the plasma-facing structural component and surface pressures from computational fluid dynamics simulations are used to determine stress distributions using commercial structural finite element modeling software over a range of fusion-relevant conditions. The maximum allowable incident heat fluxes are determined based on the temperature limits imposed by the ITER elastic Structural Design Criteria for In-vessel Components (SDC-IC) and the maximum RT over a range of He mass flow rates and presented in the form of performance design charts. Our recent work found that thermal- structural criteria accounting for the low ductility of W in a finger-type modular divertor constrain the maximum incident heat fluxes to values well below the ITER specifications, and those based on considering only the RT demonstrate that integrated thermal-fluid and elastic structural performance evaluation are required for accurate assessment of divertor performance. This novel analysis of the T-tube considers how nonuniform and transient incident heat fluxes affect its thermal-fluid and thermal-structural performance, as well as the effect of volumetric heating, which can be as great as 27% of the power incident on the divertor surface. The W tile of the T-tube, with its relatively large plasma-facing area of ~15 cm 2 , will likely experience significant spatial variations in incident heat flux. This work therefore assesses whether steady-state incident heat flux profiles with a peak of 10 MW/m 2 and maximum heat flux gradients of 200 MW/m 2 per m exceed the structural limits imposed by the ITER elastic SDC-IC and the maximum RT over a range of fusion-relevant conditions. The effect of transient heat fluxes typical of plasma detachment and reattachment from the target plate due, for example, to gas injection are also evaluated

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Improving and Automating Building Model Data Exchange

There are many instances throughout a project’s lifecycle where there arises a need for quick and accurate risk assessment of building designs. For example, an unexpected design change during construction may necessitate structural engineers to perform a seismic risk assessment on analytical models of the updated building design using high fidelity structural analysis software, such as ANSYS or Abaqus. However, the efficiency of such workflows often depends upon the interoperability of architectural design software and structural analysis software. When the quality of this interoperability is lacking or even non-existent, the efficiency of virtual engineering workflows is hampered, which increases project costs. A McGraw Hill industry survey of professional users of Building Information Modeling (BIM) technologies found that there is high demand for BIM interoperability for structural analysis, but that the value/difficulty ratio is currently too low for practical use. There have been efforts by the academic community to facilitate model data exchange between the architectural design and structural analysis domains, but such solutions have not been widely adopted by industry, face technical challenges, and oftentimes are limited in applicability for users of various BIM software. Therefore, INL is developing capabilities to improve, automate, and generalize model data exchange between architectural BIM software (e.g., Revit) and structural analysis software (e.g., SAP2000, ANSYS). The goal is to help expedite and automate as much of the pre-processing step for creating analytical models in finite element analysis software as reasonably as possible. Such a "BIM-to-FEA" conversion tool should provide direct benefit to end-users through accuracy, automation, quick turn-around, and wide applicability. To generalize the application of this BIM-to-FEA conversion tool and increase its useability among the many different commercial BIM software currently used by industry, the program is being developed with the concept of openBIM. OpenBIM is the application of non-proprietary, open data standards that allow for BIM model data exchange in a format that is accessible, retainable, and useable for all users. The most widely used open, non-proprietary data exchange format for BIM is the Industry Foundation Classes (IFC) schema. IFC is developed by buildingSMART international and is ISO certified (ISO 16739-1:2018). The BIM-to-FEA conversion tool is being developed for compatibility with typical commercial building designs of steel framed structures. The tool is currently capable of importing architectural BIM data of framed building structures, recognizing and extracting the aspects of the model that are required for structural analysis, adjusting the connectivity of frame members, and finally exporting to an analytical model stored in the IFC format. The exported IFC analytical model can then be imported into various openBIM compliant software, such as SAP2000. Such capabilities have already been tested on commercial software, as shown above, and continue to be improved. Work is underway to test the conversion on various commercial BIM software, develop a user-friendly interface, incorporate the program into the broader DeepLynx data warehouse project being developed by INL, and to eventually open-source the tool for the benefit of the community. Future development of the tool envisions the ability for efficient iterative risk assessment of generative building designs, all within a workflow utilizing open-source tools. One such open-source tool will be MOOSE, an advanced finite element analysis tool developed at INL. The conversion tool will also branch out from typical commercial building designs and will aim to incorporate nuclear construction. The aim will be to convert both structural and non-structural components of nuclear facilities, such as curved concrete containment structures and piping systems, respectively.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2020

Multiscale-Informed Modeling of High Temperature Component Response with Uncertainty Quantification

This report summarizes a joint effort between Argonne National Laboratory, Idaho National Laboratory, and Los Alamos National Laboratory to develop and deploy constitutive models targeted at predicting the life of Grade 91 alloy components subjected to high temperature environments typical of those that structural components in advanced nuclear reactors would experience. Two distinct, but complementary constitutive modeling approaches have been taken here. The first employs a phenomenological viscoplastic model for which parameters have been calibrated based on experimental data for a wide range of Grade 91 alloy that has undergone a variety of processing. A Bayesian approach was used to derive distributions of uncertain parameters for this model based on this data set. The second approach is a reduced order model suitable for engineering-scale analysis that is based on the results of a large set of mesoscale simulations. Mesoscale models allow for the microstructure and composition of a particular alloy to be directly taken into account in the computation of the viscoplastic response, but are computationally expensive, which makes it impractical to directly call those models for the material constitutive response in an engineering-scale simulation. The reduced-order representation of the response of the underlying model used here allows for an engineering-scale model to take into account the characteristics of the underlying microstructure, while only incurring a reasonable computational expense. Both of these approaches have different strengths, and are applicable for different parts of the design/analysis process. The phenomenological models can be readily parameterized based on a set of experimental data for a given class of materials and used for scoping calculations. Once a specific material is chosen and adequately characterized, the reduced order models can accurately predict the response of that specific alloy, and because the models are based on predictive models of the underlying microstructure, they can be used to more confidently predict the response under conditions in regions where there is limited experimental data. Both of these models have been integrated in the Grizzly code, which is used here to perform proof-of-concept uncertainty quantification analyses of a simple component under prototypical conditions. The built- in stochastic analysis capabilities in the MOOSE framework that Grizzly is built on are used here to run large sets of simulations for this uncertainty quantification analysis. As would be expected, because the reduced order models are developed for a much more tightly defined alloy, they predict tighter distributions of the time to failure than the phenomenological models, which are calibrated to a broader set of data. Also important is that these simulations demonstrate that a reduced order modeling approach can be successfully deployed to propagate uncertainties from the material scale to practical engineering-scale component simulations.

42 ENGINEERING↗

DOE OSTI2020

Initial development for the introduction of provisions for irradiation effects in Division 5 rules

Heat pipe microreactor concept involves the use of a solid core block to encapsulate the nuclear fuel and the passive extraction of heat from the core block to the heat exchanger block by advanced heat pipes. The core block is a key component of the heat pipe microreactor design. It integrates the functions of reactor vessel, core structural components and fuel cladding of traditional Gen IV advanced reactor designs into one single structure. The effects of irradiation on the structural failure modes are outside the scope of the rules of the ASME Boiler and Pressure Vessel Code, Section III, Division 5, Subsection HB, Subpart B for metallic Class A components. Methods to account for the irradiation effect were investigated in order to develop design methods that can be applied to the core block design in the heat pipe microreactor. This report presents an initial development of an approach to account for the irradiation effects in the design rules.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Report on Properties and Microstructure of 3D Printed Inc-718

The report presents the microstructure and mechanical properties of 3D printed Inconel 718 to assess its potential use as a structural material for the Transformation Challenge Reactor (TCR). The structural components near the outlet of the core will experience significant neutron fluxes and outlet coolant temperatures from the hot standby temperature of 300°C to nearly 550°C at the center of the part. These components must support the core in appropriate loading conditions and require structural analysis at relevant temperatures. Strong spatial and chemical heterogeneity was found in as-built (ASB) Inconel 718. Three heat treatments were designed and conducted to simplify the microstructure and determine how each precipitating phase contributed to the overall strength. Baseline mechanical properties were measured from uniaxial tensile tests on subsize SS-J2 specimens at room temperature and at elevated temperatures of 300, 450, and 600°C. Microstructure electron microscopy was performed on ASB Inconel 718 and heat treated to correlate the observed mechanical properties with nanoscale features. Homogenization of the microstructure led to a highly ductile Inconel with lower strength compared with wrought Inconel 718. The tensile properties of additively manufactured 718 using a standard ASTMrecommended heat treatment were consistent with literature and with the ASTM for the properties of this alloy. A higher fraction of the δ phase led to shorter uniform elongation without altering other engineering properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗