Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stiffness removal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Method Developed for the High-Temperature Nondestructive Evaluation of Fiber-Reinforced Silicon Carbide Ceramic Matrix Composites

Ceramic matrix composites have emerged as candidate materials to allow higher operating temperatures (1000 to 1400 C) in gas turbine engines. A need, therefore, exists to develop nondestructive methods to evaluate material integrity at the material operating temperature by monitoring thermal and mechanical fatigue. These methods would also have potential as quality inspection tools. The goal of this investigation at the NASA Lewis Research Center is to survey and correlate the temperature-dependent damping and stiffness of advanced ceramic composite materials with imposed thermal and stress histories that simulate in-service turbine engine conditions. A typical sample size of 100 by 4 by 2 cubic millimeters, along with the specified stiffness and density, placed the fundamental vibration frequencies between 100 and 2000 Hz. A modified Forster apparatus seemed most applicable to simultaneously measure both damping and stiffness. Testing in vacuum reduced the effects of air on the measurements. In this method, a single composite sample is vibrated at its fundamental tone; then suddenly, the mechanical excitation is removed so that the sample's motion freely decays with time. Typical results are illlustrated in this paper.

Goldsby, Jon C.↗
DOE OSTI2021

A non‐intrusive domain‐decomposition model reduction method for linear steady‐state partial differential equations with random coefficients

Abstract Domain decomposition methods have been proved to be an effective strategy to reduce the dimension of parametric partial differential equations (PDEs). However, existing domain decomposition methods for parametric PDEs are usually intrusive, which means domain decomposition based solvers need to be implemented from scratch for each target parametric PDE. To address this issue, we develop a new non‐intrusive domain‐decomposition model reduction method for linear steady‐state PDEs with random‐field coefficients. As a variant of our previous work by Mu and Zhang, the new method only needs access to the final linear system, that is, the global stiffness matrix and the right hand side, of a deterministic PDE solver, in order to build a domain‐decomposition‐based reduced model without intrusive implementation from scratch. The key idea is to remove the interface condition between sub‐domains and rely on the correlation between columns of the linear system to couple the sub‐domains. The non‐intrusive feature enables the applicability of the proposed method to a broader class of uncertainty quantification problems, where many legacy codes/solvers can be fully reused by our method. Two numerical examples including diffusion equations with random diffusivity and convection‐dominated transport with random velocity, are provided to demonstrate the effectiveness and efficiency of our method.

Zhang, Guannan↗
NASA NTRS1990

Behaviour of plate elements based on the first-order shear deformation theory

A new analytical technique to assess the performance of shear deformable elements is presented, which makes it possible to determine a priori whether a given element will lock when used to model thin structures. The role that shear constraints play in determining the behavior of thin elements was established by comparing the results of key numerical tests with the predictions of element behavior made by studying the form of the shear constraints. Conclusions regarding locking behavior and the effects of reduced integration in thin shear deformable elements are presented, including the findings (1) that singularity of the shear stiffness matrix is not sufficient to avoid locking; (2) that the effect of mesh refinement on an element that contains spurious constraints is two-fold; and (3) that reduced integration does not remove spurious constraints but rather relaxes them. The results of the study are in agreement with previous studies of Mindlin plate elements in regarding Lagrangian elements as superior to serendipity elements when either full or reduced integration is employed.

Averill, R. C.↗
NASA NTRS2004

Helping Aircraft Engines Lighten Up

High-temperature polyimide/carbon fiber matrix composites are developed by the Polymers Branch at NASA's Glenn Research Center. These materials can withstand high temperatures and have good processing properties, which make them particularly useful for jet and rocket engines and for components such as fan blades, bushings, and duct segments. Applying polyimide composites as components for aerospace structures can lead to substantial vehicle weight reductions. A typical polyimide composite is made up of layers of carbon or glass fibers glued together by a high-temperature polymer to make the material strong, stiff, and lightweight. Organic molecules containing carbon, nitrogen, oxygen, and hydrogen within the polyimide keep the material s density low, resulting in the light weight. The strength of a component or part made from a polyimide comes mainly from the reinforcing high-strength fibers. The strength of the carbon fibers coupled with the stiffness of polyimides allows engineers to make a very rigid structure without it being massive. Another benefit of a polyimide s suitability for aerospace applications is its reduced need for machining. When polyimide parts are removed from a mold, they are nearly in their final shape. Usually, very little machining is needed before a part is ready for use.

Source record↗
NASA NTRS1977

Earth orbital teleoperator manipulator system evaluation program

The operator's ability to perform five manipulator tip movements while using monoptic and stereoptic video systems was assessed. Test data obtained were compared with previous results to determine the impact of camera placement and stereoptic viewing on manipulator system performance. The tests were performed using the NASA MSFC extendible stiff arm Manipulator and an analog joystick controller. Two basic manipulator tasks were utilized. The minimum position change test required the operator to move the manipulator arm to touch a target contract. The dexterity test required removal and replacement of pegs.

Brye, R. G.↗
DOE OSTI2022

An energy-based study of the embedded element method for explicit dynamics

Abstract The embedded finite element technique provides a unique approach for modeling of fiber-reinforced composites. Meshing fibers as distinct bundles represented by truss elements embedded in a matrix material mesh allows for the assignment of more specific material properties for each component rather than homogenization of all of the properties. However, the implementations of the embedded element technique available in commercial software do not replace the material of the matrix elements with the material of the embedded elements. This causes a redundancy in the volume calculation of the overlapping meshes leading to artificially increased stiffness and mass. This paper investigates the consequences in the energy calculations of an explicit dynamic model due to this redundancy. A method for the correction of the edundancy within a finite element code is suggested which removes extra energy and is shown to be effective at correcting the energy calculations for large amounts of redundant volume.

Martin, Valerie A.↗
NASA NTRS2004

Experimental Results From Stitched Composite Multi-Bay Fuselage Panels Tested Under Uni-Axial Compression

The experimental results from two stitched VARTM composite panels tested under uni-axial compression loading are presented. The curved panels are divided by frames and stringers into five or six bays with a column of three bays along the compressive loading direction. The frames are supported at the ends to resist out-of-plane translation. Back-to-back strain gages are used to record the strain and displacement transducers were used to record the out-of-plane displacements. In addition a full-field measurement technique that utilizes a camera-based-stero-vision system was used to record displacements. The panels were loaded in increments to determine the first bay to buckle. Loading was discontinued at limit load and the panels were removed from the test machine for impact testing. After impacting at 20 ft-lbs to 25 ft-lbs of energy with a spherical indenter, the panels were loaded in compression until failure. Impact testing reduced the axial stiffness 4 percent and less than 1 percent. Postbuckled axial panel stiffness was 52 percent and 70 percent of the pre-buckled stiffness.

Baker, Donald J.↗
NASA NTRS1999

Hybrid Active-Passive Systems for Control of Aircraft Interior Noise

Previous work has demonstrated the large potential for hybrid active-passive systems for attenuating interior noise in aircraft fuselages. The main advantage of an active-passive system is, by utilizing the natural dynamics of the actuator system, the control actuator power and weight is markedly reduced and stability/robustness is enhanced. Three different active-passive approaches were studied in the past year. The first technique utilizes multiple tunable vibration absorbers (ATVA) for reducing narrow band sound radiated from panels and transmitted through fuselage structures. The focus is on reducing interior noise due to propeller or turbo fan harmonic excitation. Two types of tunable vibration absorbers were investigated; a solid state system based upon a piezoelectric mechanical exciter and an electromechanical system based upon a Motran shaker. Both of these systems utilize a mass-spring dynamic effect to maximize tile output force near resonance of the shaker system and so can also be used as vibration absorbers. The dynamic properties of the absorbers (i.e. resonance frequency) were modified using a feedback signal from an accelerometer mounted on the active mass, passed through a compensator and fed into the drive component of the shaker system (piezoelectric element or voice coil respectively). The feedback loop consisted of a two coefficient FIR filter, implemented on a DSP, where the input is acceleration of tile ATVA mass and the output is a force acting in parallel with the stiffness of the absorber. By separating the feedback signal into real and imaginary components, the effective natural frequency and damping of the ATVA can be altered independently. This approach gave control of the resonance frequencies while also allowing the simultaneous removal of damping from the ATVA, thus increasing the ease of controllability and effectiveness. In order to obtain a "tuned" vibration absorber the chosen resonant frequency was set to the excitation frequency. In order to minimize sound radiation a gradient descent algorithm was developed which globally adapted the resonance frequencies of multiple ATVA's while minimizing a cost based upon the radiated sound power or sound energy obtained from an array of microphones.

Fuller, Chris R.↗
DOE OSTI2023

Metal (Cu,Al)/CNT Composite Wires for Energy Efficient Motors

This report summarizes the main results of research project on Metal/CNT nanocomposites conducted at University of Central Florida (UCF). It should be noted that the project was budgeted for three years, but the budget period 3 was unfortunately not funded and conducted in COVID19 pandemic years due to many reasons. The demonstration plan on the small motors was also removed according to the discussion with the DOE program manager. All research activities were focused on the (Cu,Al)/CNT material development and wire extrusion. Existing methods to fabricate Metal/CNTs were usually suffering from agglomeration of CNTs due to their density and stiffness differences. A new method is studied by the UCF research team, where CNTs are surface treated firstly, then coated with pure metals (i.e., Al, Cu, and Nickle). The metal encapsulation on CNT is expected to significantly improve the interfacial bonding between CNTs and the intimated metal matrices. The coated CNT powders were used to make sample materials through sintering, then a customized wire extrusion process was employed to fabricate wires. Measurement of material property improvements in mechanical strength, thermal conductivity, and electrical conductivity were conducted on both cylinder samples and extruded wires. In addition to the sintering process, casting on metal coated CNT powder was also investigated. The best results we achieved are summarized as follows. (1) The measured thermal conductivity of Al/CNT composite made with Ni-encapsulated CNTs and pure Al powders is about 85% better than that of pure aluminum fabricated. The measured electrical conductivity of fabricated Al/CNT is about 14-20% better than that of pure aluminum. (2) The measured electrical conductivity of Cu/CNT is about 14.5% better than that of pure copper fabricated. (3) The mechanical strengths of both Cu/CNT and Al/CNT (with about 1% wt. CNTs) are 70% better than pure metals although losing some material ductility. (4) Two-stage wire extrusion at high temperatures were designed and successfully conducted to fabricate wires of Metal/CNTs.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Generalization of rectangular element stiffness matrix and thermal load vector associated with a(0) + a(1)x + a(2)y + a(3)xy type interpolation rule

The stiffness-matrix formulation for the rectangular finite element described by Melosh (1963) and Weaver and Johnston (1984) is generalized to orthotropic materials with material axes not necessarily coincident with the x and y axes; i.e., the condition d(13) = d(23) = 0 is removed. Also included are explicit expressions for the element load vector associated with nonuniform temperature increase in the element. Applications to the analysis of thermal stresses in thin Si-crystal ribbons subjected to temperature changes with highly nonuniform lengthwise and transverse gradients (Utku et al., 1986) and to the simulation of the thermoviscoelastic behavior of growing Si ribbons (Utku and Ray, 1986) are indicated.

Ray, Sujit K.↗
DOE OSTI2023

Efficient Integration of Algebraic Constraint for Exponential Time Integration

This work is a continuation of a previous project where the high efficiency of exponential integration methods for DRMHD systems was demonstrated. Often algebraic constraints must also be enforced for DRMHD systems of interest. Straightforward application of exponential methods to DRMHD equations with constraints leads to prohibitively computationally expensive methods. In this work, we propose new exponential schemes that allow the constraints to be removed from evaluation of exponential matrix functions which drastically reduces computational complexity by eliminating the need to perform computations enforcing constraints in exponential calculations while still preserving a high order of accuracy and allowing for a large time step even when the problem is stiff. This idea is similar to the W-methods and is achieved by carefully designing a method with the desired order of accuracy, even with an incomplete Jacobian matrix used as an argument of exponential-like functions. The constraints are accounted for by including them in the evaluation of the right-hand-side forcing function of the spatially discretized system. We study performance of the new methods on test problems and outline future research directions that this work opens.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1974

A stiffness derivative finite element technique for determination of crack tip stress intensity factors

A finite element technique for determination of elastic crack tip stress intensity factors is presented. The method, based on the energy release rate, requires no special crack tip elements. Further, the solution for only a single crack length is required, and the crack is 'advanced' by moving nodal points rather than by removing nodal tractions at the crack tip and performing a second analysis. The promising straightforward extension of the method to general three-dimensional crack configurations is presented and contrasted with the practical impossibility of conventional energy methods.

Parks, D. M.↗
DOE OSTI2023

Intermittent supplementation with fisetin improves arterial function in old mice by decreasing cellular senescence

Cellular senescence and the senescence-associated secretory phenotype (SASP) contribute to age-related arterial dysfunction, in part, by promoting oxidative stress and inflammation, which reduce the bioavailability of the vasodilatory molecule nitric oxide (NO). In the present study, we assessed the efficacy of fisetin, a natural compound, as a senolytic to reduce vascular cell senescence and SASP factors and improve arterial function in old mice. We found that fisetin decreased cellular senescence in human endothelial cell culture. In old mice, vascular cell senescence and SASP-related inflammation were lower 1 week after the final dose of oral intermittent (1 week on—2 weeks off—1 weeks on dosing) fisetin supplementation. Old fisetin-supplemented mice had higher endothelial function. Leveraging old p16-3MR mice, a transgenic model allowing genetic clearance of p16 INK4A -positive senescent cells, we found that ex vivo removal of senescent cells from arteries isolated from vehicle- but not fisetin-treated mice increased endothelium-dependent dilation, demonstrating that fisetin improved endothelial function through senolysis. Enhanced endothelial function with fisetin was mediated by increased NO bioavailability and reduced cellular- and mitochondrial-related oxidative stress. Arterial stiffness was lower in fisetin-treated mice. Ex vivo genetic senolysis in aorta rings from p16-3MR mice did not further reduce mechanical wall stiffness in fisetin-treated mice, demonstrating lower arterial stiffness after fisetin was due to senolysis. Lower arterial stiffness with fisetin was accompanied by favorable arterial wall remodeling. The findings from this study identify fisetin as promising therapy for clinical translation to target excess cell senescence to treat age-related arterial dysfunction.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1985

A dual spin space station design

A dual spin space station design is described. The space station has a cylindrical solar array that is spun to provide both gyroscopic stiffness to the space station and to stiffen the array structure. The platform is spun at the orbital angular rate. The space station is designed to have gravity gradient and aerodynamic restoring torques. An active control system is used to stabilize the station and store excess angular momentum until it can be removed from the station by magnetic torques.

Paluszek, M. A.↗
NASA NTRS1976

Track-train dynamic analysis and test program. Barber S-2 static test

The results of a static test of a Barber S-2 freight truck conducted to measure the stiffness and friction parameters of the modes of deformation which are being used in various mathematical models in the railroad industry were presented. Some difficulty was first experienced with the truck hardware since it was in an essentially new condition with many high spots causing interference. No difficulty was experienced once the interference was removed. The characteristics of the Barber S-2 are very similar to the ASF ride control truck. The major difference between the two trucks is the amount of friction between the bolster and side frames in both the vertical and lateral directions. The Barber S-2 has approximately twice the friction the ASF ride control truck has in the fully loaded condition. This does not necessarily imply that all trucks will have this same ratio of friction.

Abbott, P. W.↗
NASA NTRS1991

Rigid lightweight optical bench for a spaceborne FUV spatial heterodyne interferometer

Requirements for spaceflight optical instruments usually dictate that for the structures be rigid, lightweight, and thermally stable. In addition, for interferometric far ultraviolet (FUV) spectrometers, the requirements for torsional deflection are more severe than with conventional spectrometers. To meet the challenge for rigid and lightweight optical instruments, this paper explores the design of a high-stiffness structure for the support of an FUV spatial heterodyne interferometer where the torsional deflection of the instrument is on the order of 10 arc seconds. The structure is based on use of a thin, hollow section beam with weight-relieving between optical elements. The design also uses a modular and self-contained positioning mechanism that is removed after final optical alignment. Several specific material properties are presented as criteria for material selection. The parameters which affect the particular design requirements are identified with respect to the desired material properties and physical design features. Although large thin sections are susceptible to thermal gradients, this could be minimized by a trade-off for weight, where adequate margin exists. This paper describes the preliminary design for the structure and presents an analysis to verify compliance with the requirements.

Tom, James L.↗
NASA NTRS1990

Performability analysis using semi-Markov reward processes

Beaudry (1978) proposed a simple method of computing the distribution of performability in a Markov reward process. Two extensions of Beaudry's approach are presented. The method is generalized to a semi-Markov reward process by removing the restriction requiring the association of zero reward to absorbing states only. The algorithm proceeds by replacing zero-reward nonabsorbing states by a probabilistic switch; it is therefore related to the elimination of vanishing states from the reachability graph of a generalized stochastic Petri net and to the elimination of fast transient states in a decomposition approach to stiff Markov chains. The use of the approach is illustrated with three applications.

Ciardo, Gianfranco↗
NASA NTRS2006

Finite Element Development of Honeycomb Panel Configurations with Improved Transmission Loss

The higher stiffness-to-mass ratio of a honeycomb panel compared to a homogeneous panel results in a lower acoustic critical frequency. Above the critical frequency the panel flexural wave speed is acoustically fast and the structure becomes a more efficient radiator with associated lower sound transmission loss. Finite element models of honeycomb sandwich structures are presented featuring areas where the core is removed from the radiating face sheet disrupting the supersonic flexural and shear wave speeds that exist in the baseline honeycomb panel. These modified honeycomb panel structures exhibit improved transmission loss for a pre-defined diffuse field sound excitation. The models were validated by the sound transmission loss of honeycomb panels measured in the Structural Acoustic Loads and Transmission (SALT) facility at the NASA Langley Research Center. A honeycomb core panel configuration is presented exhibiting a transmission loss improvement of 3-11 dB compared to a honeycomb baseline panel over a frequency range from 170 Hz to 1000 Hz. The improved transmission loss panel configuration had a 5.1% increase in mass over the baseline honeycomb panel, and approximately twice the deflection when excited by a static force.

Grosveld, Ferdinand W.↗