Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “State of Practice”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Demonstration of Multi-Gbps Data Rates at Ka-Band Using Software-Defined Modem and Broadband High Power Amplifier for Space Communications

The paper presents the first ever research and experimental results regarding the combination of a software-defined multi-Gbps modem and a broadband high power space amplifier when tested with an extended form of the industry standard DVB-S2 and LDPC rate 9/10 FEC codec. The modem supports waveforms including QPSK, 8-PSK, 16-APSK, 32-APSK, 64-APSK, and 128-QAM. The broadband high power amplifier is a space qualified traveling-wave tube (TWT), which has a passband greater than 3 GHz at 33 GHz, output power of 200 W and efficiency greater than 60 percent. The modem and the TWTA together enabled an unprecedented data rate at 20 Gbps with low BER of 10(exp -9). The presented results include a plot of the received waveform constellation, BER vs. E(sub b)/N(sub 0) and implementation loss for each of the modulation types tested. The above results when included in an RF link budget analysis show that NASA s payload data rate can be increased by at least an order of magnitude (greater than 10X) over current state-of-practice, limited only by the spacecraft EIRP, ground receiver G/T, range, and available spectrum or bandwidth.

Simons, Rainee N.↗
NASA NTRS2011

Peak Satellite-to-Earth Data Rates Derived From Measurements of a 20 Gbps Bread-Board Modem

A prototype data link using a Ka-band space qualified, high efficiency 200 W TWT amplifier and a bread-board modem emulator were created to explore the feasibility of very high speed communications in satellite-to-earth applications. Experiments were conducted using a DVB-S2-like waveform with modifications to support up to 20 Gbps through the addition of 128-Quadrature Amplitude Modulation (QAM). Limited by the bandwidth of the amplifier, a constant peak symbol rate of 3.2 Giga-symbols/sec was selected and the modulation order was varied to explore what peak data rate might be supported by an RF link through this amplifier. Using 128-QAM, an implementation loss of 3 dB was observed at 20 Gbps, and the loss decreased as data rate or bandwidth were reduced. Building on this measured data, realistic link budget calculations were completed. Low-Earth orbit (LEO) missions based on this TWTA with reasonable hardware assumptions and antenna sizing are found to be bandwidth-limited, rather than power-limited, making the spectral efficiency of 9/10-rate encoded 128-QAM very attractive. Assuming a bandwidth allocation of 1 GHz, these computations indicate that low-Earth orbit vehicles could achieve data rates up to 5 Gbps-an order of magnitude beyond the current state-of-practice, yet still within the processing power of a current FPGA-based software-defined modem. The measured performance results and a description of the experimental setup are presented to support these conclusions.

Landon, David G.↗
NASA NTRS2011

Ka-Band, Multi-Gigabit-Per-Second Transceiver

A document discusses a multi-Gigabit-per-second, Ka-band transceiver with a software-defined modem (SDM) capable of digitally encoding/decoding data and compensating for linear and nonlinear distortions in the end-to-end system, including the traveling-wave tube amplifier (TWTA). This innovation can increase data rates of space-to-ground communication links, and has potential application to NASA s future spacebased Earth observation system. The SDM incorporates an extended version of the industry-standard DVB-S2, and LDPC rate 9/10 FEC codec. The SDM supports a suite of waveforms, including QPSK, 8-PSK, 16-APSK, 32- APSK, 64-APSK, and 128-QAM. The Ka-band and TWTA deliver an output power on the order of 200 W with efficiency greater than 60%, and a passband of at least 3 GHz. The modem and the TWTA together enable a data rate of 20 Gbps with a low bit error rate (BER). The payload data rates for spacecraft in NASA s integrated space communications network can be increased by an order of magnitude (>10 ) over current state-of-practice. This innovation enhances the data rate by using bandwidth-efficient modulation techniques, which transmit a higher number of bits per Hertz of bandwidth than the currently used quadrature phase shift keying (QPSK) waveforms.

Simons, Rainee N.↗
NASA NTRS2013

Slotted Polyimide-Aerogel-Filled-Waveguide Arrays

This presentation discussed the potential advantages of developing Slotted Waveguide Arrays using polyimide aerogels. Polyimide (PI) aerogels offer great promise as an enabling technology for lightweight aerospace antenna systems. PI aerogels are highly porous solids possessing low density and low dielectric permittivity combined with good mechanical properties. For slotted waveguide array applications, there are significant advantages in mass that more than compensate for the slightly higher loss of the aerogel filled waveguide when compared to state of practice commercial waveguide.

Slotted Waveguide Arrays↗
NASA NTRS2014

Design and Development of Aerogel-Based Antennas for Aerospace Applications: A Final Report to the NARI Seedling

As highly porous solids possessing low density and low dielectric permittivity combined with good mechanical properties, polyimide (PI) aerogels offer great promise as an enabling technology for lightweight aircraft antenna systems. While they have been aggressively explored for thermal insulation, barely any effort has been made to leverage these materials for antennas or other applications that take advantage of their aforementioned attributes. In Phase I of the NARI Seedling Project, we fabricated PI aerogels with properties tailored to enable new antenna concepts with performance characteristics (wide bandwidth and high gain) and material properties (low density, environmental stability, and robustness) superior to the state of practice (SOP). We characterized electromagnetic properties, including permittivity, reflectivity, and propagation losses for the aerogels. Simple, prototype planar printed circuit patch antennas from down-selected aerogel formulations were fabricated by molding the aerogels to net shapes and by gold-metalizing the pattern onto the templates via electron beam evaporation in a clean room environment. These aerogel based antennas were benchmarked against current antenna SOP, and exhibited both broader bandwidth and comparable or higher gain performance at appreciably lower mass. Phase II focused on the success of the Phase I results pushing the PI aerogel based antenna technology further by exploring alternative antenna design (i.e., slot coupled antennas) and by examining other techniques for fabricating the antennas including ink jet printing with the goal of optimizing antenna performance and simplifying production. We also examined new aerogel formulations with better moisture and solvent resistance to survive processing conditions. In addition, we investigated more complex antenna designs including passive phased arrays such as 2x4 and 4x8 element arrays to assess the scalability of the aerogel antenna concept. Furthermore, we explored the possibility of developing these arrays in thin, flexible form to make conformable antennas.

insulation↗
NASA NTRS2011

Aerospace Concurrent Engineering Design Teams: Current State, Next Steps and a Vision for the Future

Over the past sixteen years, government aerospace agencies and aerospace industry have developed and evolved operational concurrent design teams to create novel spaceflight mission concepts and designs. These capabilities and teams, however, have evolved largely independently. In today's environment of increasingly complex missions with limited budgets it is becoming readily apparent that both implementing organizations and today's concurrent engineering teams will need to interact more often than they have in the past. This will require significant changes in the current state of practice. This paper documents the findings from a concurrent engineering workshop held in August 2010 to identify the key near term improvement areas for concurrent engineering capabilities and challenges to the long-term advancement of concurrent engineering practice. The paper concludes with a discussion of a proposed vision for the evolution of these teams over the next decade.

concurrent engineering design↗
NASA NTRS2008

Thermal Expansion Studies of Selected High Temperature Thermoelectric Materials

Radioisotope thermoelectric generators (RTGs) generate electrical power by converting the heat released from the nuclear decay of radioactive isotopes (typically plutonium-238) into electricity using a thermoelectric converter. RTGs have been successfully used to power a number of space missions and have demonstrated their reliability over an extended period of time (tens of years) and are compact, rugged, radiation resistant, scalable, and produce no noise, vibration or torque during operation. System conversion efficiency for state-of-practice RTGs is about 6% and specific power less than or equal to 5.1 W/kg. Higher specific power would result in more on-board power for the same RTG mass, or less RTG mass for the same on-board power. The Jet Propulsion Laboratory has been leading, under the advanced thermoelectric converter (ATEC) project, the development of new high-temperature thermoelectric materials and components for integration into advanced, more efficient RTGs. Thermoelectric materials investigated to date include skutterudites, the Yb14MnSb11 compound, and SiGe alloys. The development of long-lived thermoelectric couples based on some of these materials has been initiated and is assisted by a thermo-mechanical stress analysis to ensure that all stresses under both fabrication and operation conditions will be within yield limits for those materials. Several physical parameters are needed as input to this analysis. Among those parameters, the coefficient of thermal expansion (CTE) is critically important. Thermal expansion coefficient measurements of several thermoelectric materials under consideration for ATEC are described in this paper. The stress response at the interfaces in material stacks subjected to changes in temperature is discussed, drawing on work from the literature and project-specific tools developed here. The degree of CTE mismatch and the associated effect on the formation of stress is highlighted.

silicon germanium↗
NASA NTRS2016

NASA Electric Aircraft Test Bed (NEAT) Development Plan - Design, Fabrication, Installation

As large airline companies compete to reduce emissions, fuel, noise, and maintenance costs, it is expected that more of their aircraft systems will shift from using turbofan propulsion, pneumatic bleed power, and hydraulic actuation, to instead using electrical motor propulsion, generator power, and electrical actuation. This requires new flight-weight and flight-efficient powertrain components, fault tolerant power management, and electromagnetic interference mitigation technologies. Moreover, initial studies indicate some combination of ambient and cryogenic thermal management and relatively high bus voltages when compared to state of practice will be required to achieve a net system benefit. Developing all these powertrain technologies within a realistic aircraft architectural geometry and under realistic operational conditions requires a unique electric aircraft testbed. This report will summarize existing testbed capabilities located in the U.S. and details the development of a unique complementary testbed that industry and government can utilize to further mature electric aircraft technologies.

Hybrid Electric↗
NASA NTRS2018

Improving NASA Earth Science Data and Information Access Through Natural Language Processing Based Data Analysis and Visualization

NASA: The Research Access initiative is part of the agency's framework for increasing public access to scientific publications and digital scientific data. The initiative follows the release of White House Office of Science and Technology Policy's (OSTP) memorandum "Increasing Access to the Results of Federally Funded Research," to ensure federally funded research is available to the public within one year of publication. NASA answered the mandate by creating an agency plan entitled "NASA Plan for Increasing Access to the Results of Scientific Research" and associated policy, NPD 2230.1, Research Data and Publication Access. Principles in NASA SMD Strategic Plan for Scientific Data and Computing: Continued free and open access to scientific data for any use. Improved ease of use and discoverability. Enhanced science applications and new use cases. Incorporates best practices and "state of the art" through partnerships. Earth Data and Systems are Evolving: Increasing archive and file sizes. More complicated data structures. More user-friendly and data services. What is the future direction?

Liu, Zhong↗
NASA NTRS2019

2018 NISAR Applications Workshop: Agriculture and Soil Moisture

Agricultural lands cover the globe and play an essential role in not only sustaining a growing global population, but can have significant implications on the Earth system through land use change (e.g., deforestation, grazing, etc.). As such, countries around the world have dedicated programs for managing these lands. Accurate and timely information concerning the status of agricultural crops (soil moisture, crop health, crop type, etc.) is essential to those nations’ anthropogenic and ecological health as well as economy. The joint NASA/US Department of Agriculture Agricultural Research Service (USDA-ARS) workshop focused on advancing agriculture and soil moisture applications by using remote sensing data from the NASA-ISRO Synthetic Aperture Radar (NISAR) mission (expected launch 2022). Participants included representatives from the international agriculture community that are key players in facilitating integration of Earth Observations into decision support workflows including US Federal Agencies, nonprofits, and private sector. They included scientists, technicians, and program managers with a responsibility for data acquisition and exploitation such as product development, delivery, and use, as well as capacity building. Discussions were held over two and a half days to convey the broader agriculture and soil moisture community information needs, the mission and procedures for various representative participants and programs involved in the delivery of geospatial products, and the capabilities and status of the NISAR mission. Case studies were presented to demonstrate the current state of practice in the use of SAR remote sensing for applications of direct importance for the agriculture and soil moisture communities. Eleven organizations presented their information requirements in response to a set of questions provided by the NASA team, then the NASA team responded by describing the degree to which NISAR could meet these requirements. Discussion ensued about needed data product specifications to increase utility (e.g., projection, latency, etc.), tools and capacity building.

Stavros, Natasha↗
NASA NTRS2019

2018 NISAR Applications Workshop: Forest and Disturbance; Workshop Report

Forest lands cover the globe and are important sources for providing ecosystem services including: carbon sequestration, biodiversity, timber, air and water quality. As such, counties around the world have dedicated programs for managing them. Accurate and timely information concerning the status of these forests (moisture, biomass, disturbance type, etc.) is essential to those Nations’ human and ecological health as well as economy. The joint NASA/US Forest Service workshop focused on arming forest land managers with observations and remote sensing information from the upcoming NASA-ISRO (Indian Space Research Organization) SAR (Synthetic Aperture Radar) (NISAR) satellite mission (expected to launch early 2022). Participants included representatives from different US Federal Agencies, private sector, and non-governmental organizations (NGO) that are key players in facilitating integration of Earth Observations (EO) into forest management and decision support workflows. They included scientists, technicians, and program managers with a responsibility for data acquisition and exploitation such as product development, delivery, and use, and capacity building. Discussions were held over two days to convey the broader forest and disturbance community information needs for various representative participants and programs and to facilitate the delivery of NISAR mission geospatial products and observational capabilities. Case studies were presented to demonstrate the current state of practice in the use of SAR remote sensing for applications of direct importance to forest and disturbance land management community. Eleven organizations presented their information requirements in response to a set of questions provided by the NASA team, then the NASA team responded by describing the degree to which NISAR could meet these requirements. Discussion ensued about needed data product specifications to increase utility (e.g., projection, latency, etc.), tools and capacity building. The general findings of this workshop were that (a) NISAR observations will be particularly useful to the global forest carbon and disturbance monitoring applications, but that certain data product design decisions (projections and radiometric and terrain corrections) need to be considered to increase utility; b) the biomass and disturbance detection algorithms meet many of the community needs, however there are other information products of value (e.g., soil moisture or disturbance classification, not just detection) and all products should be compliant with existing community standards for reporting uncertainty; c) providing SAR education to the community will be key specifically thinking about putting the information first and the SAR theory second, providing a simple guide of standard data processing steps (e.g., dB (decibel) to power conversion and speckle filtering); d) the community needs a user-friendly interface for finding free, archived data over their geographic regions of interest; e) user-friendly tools that connect to open-sources GIS (Global Information System) software (e.g., QGIS (Quantum GIS)) that include a graphical user interface (GUI) for SAR processing that enables both download and cloud processing. To integrate these findings and prepare the community before NISAR launches, it was suggested that there be a dedicated NISAR Forest and Disturbance Applications Working Group (as per the specifications in the NISAR Utilization Plan). After launch, it was decided that the community continue capacity building activities.

Stavros, Natasha↗
NASA NTRS2020

Hybrid Electric MC-12 Ground Testing Plan Chapter

In the commercial aviation world, hybrid/electric propulsion is a promising technology for fuel, emissions, and noise reduction in support of the challenging goals established by 2050 EU Flightpath/SRIA, NASA ARMD Strategic Implementation Plan, and the US Air Force ATTAM programs. Ongoing results indicate operational benefits are possible in those three technical areas. Considering military applications, hybrid/electric propulsion may yield further significant improvements by enabling new, unorthodox mission capabilities. Potential benefits are expected in the areas of vehicle signature reduction (lower noise, lower exhaust signature), usage in enhanced flight environments, minimized human-in-the-loop workload by offering a platform compatible with future goals of autonomous operations facilitation, maintenance cost reductions, and performance burst/dash energy. Additional synergies are likely when used in conjunction with energy weapons. Some potential areas of mutual interest could include, dusty operations capability, remote supply capability, extended surveillance, dispatch able power, fuel-flexible vehicles, and autonomous rescue equipment. Many of the key technologies that have been demonstrated in ground operation must now be qualified for altitude conditions. We expect to have many flight qualified powertrain systems over the next decade for military planners to choose from for new future battlefield capability. This requires new flight-weight and flight-efficient powertrain components, fault tolerant power management, and electromagnetic interference mitigation technologies. Moreover, initial studies indicate some combination of ambient and cryogenic thermal management and relatively high bus voltages when compared to state of practice will be required to achieve a net system benefit. Developing all these powertrain technologies within a realistic aircraft architectural geometry and under realistic operational conditions requires a unique electric aircraft test bed. The MC-12 surveillance aircraft is an ideal military aircraft for demonstrating some of the benefits of incorporating hybrid electric propulsion. This report details an approach for full-scale ground-based altitude testing the hybrid electric MC-12 powertrain through a full flight profile.

military electric aircraft propulsion↗
NASA NTRS2019

Solar power for deep-space applications: state of art and development

Solar arrays have been used successfully as the power source for multiple NASA spacecraft, including in deep space as far as the Jupiter orbit at 5.5AU. In this paper, we outline the challenges to solar array performance in deep space environments, and overview the current state of practice. We also highlight recent results from our work on developing solar cells optimized for low irradiance, low temperature (LILT) operating conditions, and the implications on extending the range of solar power out to the Saturn orbit at 9.5AU.

Kowalczyk, Robert S.↗
NASA NTRS2020

Efficient Thermal Management for Sampling Arm Actuators

An electric actuator incorporating novel features for thermal management is designed and analyzed. Reducing intra-actuator thermal resistance is not only beneficial for cold missions (helping to pre-heat the gearbox) but can also enable high power applications in benign environments. The proposed design increases the thermal conductance between the motor windings and the motor casing by at least two orders of magnitude over the state of practice actuator designs. The design leverages Additive Manufacturing (AM) to integrate a complex 3 dimensional Oscillating Heat Pipe (OHP) directly within the actuator structure. A baseline actuator without this thermal management feature was fabricated. Testing was conducted to evaluate the temperature difference between actuator components at a range of motor winding heat dissipations. An analysis of a proposed revised design incorporating OHPs into the input structure indicated an increase in the effective thermal conductivity of 8 and 22 times for the nominal and start-up modes respectively. In addition, the thermal conductance between the windings and the input structure is increased by a factor of 90, and the thermal conductance between the windings and the gear assembly is increased by a factor of 200 with the proposed design.

Odagiri, Kimihide↗
NASA NTRSDate not supplied

NASA's Identified Risk of Adverse Outcomes due to Inadequate Human Systems Integration Architecture

The NASA Human System Risk Board (HSRB) is responsible for tracking the evolution of the top ~30 human system risks identified to be associated with human spaceflight. As part of this process, the Board is charged with maintaining a consistent, integrated process to evaluate those risks and developing evidence-based risk posture recommendations. Risks are ranked by likelihood and consequence. Intermediate causal relationships between risk contributing factors and countermeasures that link hazards to outcomes are described using Directed Acyclic Graphs (DAGs). The DAGs are also useful for identifying common factors and countermeasures across the top 30 risks as well as communicating how astronaut exposure to spaceflight hazards leads to meaningful mission-level health and performance outcomes. One of the top risks tracked by the HSRB is The Risk of Adverse Outcomes Due to Inadequate Human-Systems Integration Architecture (HSIA). This risk captures the possibility that due to decreasing real-time ground support during missions beyond LEO, crew will be unable to adequately respond to unanticipated critical malfunctions or detect safety-critical procedural errors. The HSIA risk is ranked red (high) for Lunar surface and Mars missions due to the probability of Loss of Crew and Loss of Mission consequences. This paper describes the evidence that supports the HSIA risk ranking and presents the central narrative of the HSIA risk DAG-- i.e., anomaly detection, diagnosis, intervention, and task performance. Characterizations of the current state of practice for each of the DAG’s central nodes and the future tools needed for successful anomaly response are provided.

human-systems integration architecture↗
NASA NTRSDate not supplied

Runway Configuration Management with Offline Reinforcement Learning

Runway configuration management (RCM) is a challenging task, and it affects the efficiency of the National Airspace System (NAS) and airport surface operations significantly. Each airport, depending on the geometry, capacity, local climate patterns, etc. has multiple configurations for the runway usage for arriving and departing flights. Many factors such as the incoming/outgoing traffic load, wind direction and speed, convective weather, cloud ceiling and other environmental factors might affect the choice of a runway configuration at any point in time. However, other factors such as safety measures and regulations, noise abatement, capacity of each configuration, and preference of the air traffic controllers (ATCs) can also play a significant role in selecting the configuration. A sub-optimal selection of the runway configuration, or delay in making configuration changes might result in significant increase in taxi times for aircraft on the surface of the airport, fuel and energy use of the aircraft, and maintenance costs. It can also lead to safety concerns, such as an aircraft performing one or more go-arounds before being able to land. All these factors make RCM an extremely important and challenging decision-making process for the ATCs. The current state of practice sets the runway configuration by the ATCs based on relevant information available at the time including weather, traffic, noise abatement, safety bounds, etc. This makes the decision-making process subjective based on the accuracy of the available information and the bias in human decision making. Unfortunately, this approach yields poor results (e.g., significant delays) if the predicted outcomes are uncertain and their relative impact is not well understood. This is especially evident when the uncertainty increases the size of possible predicted outcomes (combinatorial explosion in possible scenarios) that cannot be handled by human reasoning. On the other hand, an automated approach based on machine intelligence can make use of historical data and search through all (or significant amount of) possible scenarios under uncertainty and make well-informed decisions.

Milad Memarzadeh↗
NASA NTRSDate not supplied

Steady-state RANS Pretest CFD Comparisons for the SWiFT NTF Test

The NATO AVT-298 research program has been underway for seven years to improve the understanding of the full-scale aerodynamics for moderately-swept hybrid wing-bodies found on future civil and military configurations and how this differs from what is measured with low Reynolds number wind tunnel testing or predicted with Computational Fluid Dynamics (CFD). Toward this effort, a hybrid wing-body configuration, known as Swept Wing Flow Test (SWiFT), was designed and tested in the Aircraft Research Association (ARA) and NASA Langley National Transonic Facility (NTF) wind tunnels. This presentation summarizes comparisons between the NTF wind tunnel data and a series of pretest CFD computations generated using steady-state Reynolds-averaged Navier-Stokes (RANS) simulations from participants representing seven institutions using nine separate flow solvers. The objective of this research was to assess the effectiveness of state-of-practice CFD methods in predicting the aerodynamics of swept wing aircraft and identify recommended areas of improvement to the methods themselves. Computational force and moment data will be presented for a series of angle-of-attack and sideslip angle sweeps over a range of Reynolds numbers at both low-speed and near-cruise Mach numbers, as tested in the NTF experiment.

National Transonic Facility↗