Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solute trapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Two-fence concept for efficient trapping of vortices on airfoils

Previous work on the use of a vortex trapped above a wing in order to produce high lift at low angles of attack is extended here. It is first postulated that the optimum way to trap a vortex is to design the airfoil section and wing so that the flow along the vortex core is minimized. It is then shown that a vertical fence both in front of and behind the separation bubble generated by the trapped vortex is an effective way to reduce the mass flow removal and its associated drag to a negligible amount. In order to show that vertical surfaces upstream and downstream of the vortex separation bubble have an opposite effect on the source requirements for vortex trapping, conformal mapping methods are used to obtain the solutions for a variety of simple two-dimensional, inviscid, incompressible flow configurations. Trapped-vortex flowfield solutions for the flow over flat plate and Clark-Y airfoils are then used to demonstrate that the heights of the fences can be tailored to make the required mass withdrawal (and therefore, the drag due to trapping) to be vanishingly small.

Rossow, Vernon J.↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
NASA NTRS1978

One-dimensional inhomogeneous Vlasov equilibria

Bernstein, Greene, and Kruskal (1957) showed how, given the electrostatic potential as a function of position, the entire distribution function for ions, and the distribution function for untrapped electrons in a one-dimensional two-species Vlasov plasma, one could determine the distribution function for the trapped electrons as the solution of an Abel integral equation. This result is generalized by replacing the statements about the distribution functions with the specification of the velocity-space distribution functions of both species at a single position in the plasma. Limiting cases are shown to correspond to the earlier treatment, and the applicability of the theory to experiment is discussed.

Crownfield, F. R., Jr.↗
DOE OSTI2021

Environmentally-Friendly Fixatives with Embedded Intelligence for Dust Management at Contaminated Sites – 21266

Wind or rain can potentially spread loose hazardous contaminants from piles of rubble and soil waiting to be trucked to a landfill site for disposal. Water, which is plentiful near remediation sites, is the traditional dust suppressant during demolition, post-demolition sizing and encapsulation as well as soil trucking activities. However, water can mobilize the toxic metal contaminants in the soil into the ground water. Ground water is highly regulated and contaminant removal is costly. InnoSense LLC (ISL) is developing DustSafe™ as a cost-effective alternative to water for various decontamination & decommissioning (D&D) applications. It is a sprayable dust abatement solution designed to actively trap, remediate, and aid in visualizing hazardous materials while preventing their dispersion by wind, water or impact. Aside from application as a dust suppressant to trap airborne toxic and radiological hazards during demolition activities, with customization DustSafe can be used to locate/characterize and remediate hazards prior to D&D activities.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1980

Minimum energy trap states of dual-spin spacecraft

The general solution to the bearing axis motor torque required to escape a minimum energy trap state is presented for oblate dual-spin spacecraft. A simplified, reduced order analysis of the bearing torque is then obtained for the case of small static imbalances, dynamic imbalances, and asymmetries on the rotor and the stator. This analysis is extended to include large asymmetry on one of the bodies. The results are applied to the design of the Galileo spacecraft.

Hollars, M. G.↗
DOE OSTI2024

Exact evaluation of large-charge correlation functions in nonrelativistic conformal field theory

The large-charge master field which generates all n -point correlation functions with an insertion of large charge Q in nonrelativistic conformal field theory is obtained. This field is used to compute Schrödinger-invariant n -point correlation functions of large-charge operators via a direct evaluation of the path integral. Conformal dimensions are found to agree with calculations based on the state-operator correspondence. The master field solution exhibits an emergent harmonic trap whose frequency is a function of the Euclidean time. The large-charge effective action with operator insertions describes a droplet of superfluid matter whose spatial size scales with the time separation of sources. The solution is used to compute Schrödinger symmetry breaking corrections in the large-charge effective field theory (EFT) due to a finite scattering length in the fundamental theory of fermions near unitarity. The scaling of these effects in the large-charge power counting scheme is established, and the size of the effects is quantified using input from quantum Monte Carlo simulations of the near-unitary gas, as well as from the large- N expansion at large charge. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
NASA NTRS1993

Self-consistent electrostatic potential due to trapped plasma in the magnetosphere

A steady state solution for the self-consistent electrostatic potential due to a plasma confined in a magnetic flux tube is considered. A steady state distribution function is constructed for the trapped particles from the constants of the motion, in the absence of waves and collisions. Using Liouville's theorem, the particle density along the geomagnetic field is determined and found to depend on the local magnetic field, self-consistent electric potential, and the equatorial plasma distribution function. A hot anisotropic magnetospheric plasma in steady state is modeled by a bi-Maxwellian at the equator. The self-consistent electric potential along the magnetic field is calculated assuming quasineutrality, and the potential drop is found to be approximately equal to the average kinetic energy of the equatorially trapped plasma. The potential is compared with that obtained by Alfven and Faelthammar (1963).

Miller, Ronald H.↗
DOE OSTI2024

Microfabricated Ion Traps on Sapphire for Larger Trap Areas and Higher Qubit Count

Surface ion traps are a promising platform for quantum computing due to their potential to store large numbers of ions that can be addressed by electrical and optical control signals in order to implement quantum algorithms. Increasing the power of the quantum computer requires increasing the number of ions, but this poses a significant challenge in that it leads to a non-linear increase in on-chip power dissipation. The primary contributor to this power scaling in current devices is the capacitance between the radio frequency (RF) electrode and the metal plane that shields the silicon substrate from the RF signals applied to it. Silicon has traditionally been chosen for the substrate material for compatibility with the processing required for multi-metal-level traps. In this work, we address these capacitance and fabrication challenges by replacing the commonly used silicon substrate with an insulating sapphire substrate to fabricate a multi-metal-level ion trap, while still employing common semiconductor manufacturing techniques. This change in substrate allows the design to remove the metal shielding from the device design, reducing the capacitance of the RF electrode. The electrical characteristics of these traps were measured, specifically trap impedance, capacitance, and voltage breakdown, and compared to nearly identical silicon trap devices. Finally, we used laser cutting techniques to shape a sapphire wafer into bowtie shapes matching silicon traps previously fabricated at Sandia National Labs to explore solutions for integrating sapphire substrates into non-rectangular ion trap designs.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2012

Floating Oil-Spill Containment Device

Previous oil containment booms have an open top that allows natural gas to escape, and have significant oil leakage due to wave action. Also, a subsea pyramid oil trap exists, but cannot move relative to moving oil plumes from deepsea oil leaks. The solution is to have large, moveable oil traps. One version floats on the sea surface and has a flexible tarp cover and a lower weighted skirt to completely entrap the floating oil and natural gas. The device must have at least three sides with boats pulling at each apex, and sonar or other system to track the slowly moving oil plume, so that the boats can properly locate the booms. The oil trap device must also have a means for removal of the oil and the natural gas. A second design version has a flexible pyramid cover that is attached by lines to ballast on the ocean floor. This is similar to fixed, metal pyramid oil capture devices in the Santa Barbara Channel off the coast of California. The ballast lines for the improved design, however, would have winches that can move the pyramid to always be located above the oil and gas plume. A third design is a combination of the first two. It uses a submerged pyramid to trap oil, but has no anchor and uses boats to locate the trap. It has ballast weights located along the bottom of the tarp and/or at the corners of the trap. The improved floating oil-spill containment device has a large floating boom and weighted skirt surrounding the oil and gas entrapment area. The device is triangular (or more than three sides) and has a flexible tarp cover with a raised gas vent area. Boats pull on the apex of the triangles to maintain tension and to allow the device to move to optimum locations to trap oil and gas. The gas is retrieved from a higher buoyant part of the tarp, and oil is retrieved from the floating oil layer contained in the device. These devices can be operated in relatively severe weather, since waves will break over the devices without causing oil leaking. Also, natural gas is entrapped and can be retrieved. All designs can use sonar to locate the moving oil plume, and then be relocated by using boats or winches to move the oil trapping devices. These devices can be constructed of treated, non-permeable DuPont Kevlar cloth (or similar material).

Jones, Jack A.↗
DOE OSTI2023

Investigation of defects in melt and solution grown perovskite CsPbBr 3 single crystals

Recently, there has been considerable interest in x-ray and gamma ray detectors with large volume and high energy resolution that operate at room temperature. To improve detector energy resolution, the carrier mobility-lifetime product needs to be increased, and the electronic trap state concentration needs to be minimized. Defect concentrations in the part per billion range can alter the charge transport and carrier recombination lifetime. In this work, thermally stimulated current spectroscopy measurements were systematically carried out in bulk halide perovskite single crystals of CsPbBr 3 over a temperature range of 80–320 K. The origins and trap parameters of CsPbBr 3 crystals from the solution growth and melt growth procedures were determined and compared. Trap concentrations were ranged from 1 × 10 11 to 1 × 10 16 cm –3 . Appreciable detector performance was observed for CsPbBr3 crystals with trap concentrations less than 1 × 10 14 cm –3 . The comparison of spectral responses of crystal samples grown using two different methods shows that, after purification, solution-grown crystals are comparable to melt-grown crystals in terms of low defect concentration and improved detector performance. Finally, for an improved mobility-lifetime product and enhanced spectral response to high energy radiation from fissile materials, trap states in either type of a crystal ingot must be reduced closer to 10 11 cm –3 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Feedback between radiation and transport in photovoltaics

By building on the generalized Hovel model, this work develops an analytical solution to unify photon recycling, light trapping, and carrier transport in solar cells. Enhanced transport due to photon recycling diffusion is considered. While photon recycling diffusion is often negligible, it can significantly support transport in cases where charge diffusion is low but radiative efficiency is high. Next, the diffusion equation is solved to determine carrier collection for planar and textured cells. Results elucidate novel features in the external quantum efficiency (EQE) curve that occur for textured cells with high absorption and limited transport. Then, the effect of limited transport on the radiative recombination of solar cells is investigated in detail. While the traditional treatment of detailed balance uses the applied voltage to calculate a cell's radiative recombination, the present approach uses the spatially resolved quasi-Fermi-level splitting (QFLS). Further, the discrepancy between the models is shown to be inconsequential to performance for cells with low radiative recombination (Si) or with high mobilities (lowly doped GaAs). However, for cells with high radiative recombination and low mobility (highly doped GaAs, polycrystalline CdTe, and thin-film perovskites), incorporating variation in QFLS in the determination of radiative recombination can become necessary for accurate photovoltaic modeling.

14 SOLAR ENERGY↗
NASA NTRS1991

Stacking the odds in favor of a space propulsion jackpot

When faced with a variety of technical options to solve a problem, program planners often try to identify one potential winner, then channel their resources into this option. The more scarce their resources are perceived to be, the more likely they are to fall into this trap of illogic. The real ideal solution could well be an optimum combination of options, not just one. Many propulsion opportunities are tantalizing solutions to the potentially high cost of travelling to other planets. Among these opportunities, nuclear thermal rockets (NTR), nuclear electric propulsion (NEP), and asteroid derived propellants stand out as high-payoff modest-challenge options, as near term as they are resolved to be made. But which to choose? Or should higher risk higher payoff technology be opted for, such as fusion? The approach advocated here, technoflex, is one that addresses NTR, NEP, and asteroid propellants in harmony rather than in isolation. Technoflex is technology rich, and option flexible. Technoflex should cost roughly the same as a classic phased technology elimination approach. The synergistic benefits amongst these three options, how they can be efficiently pursued together, and how they can fit with longer range technologies are stressed. Even if no single option reaches its highest expectations, the combinations of any two partial winners would still give big dividends. These combinations are cheap propellants in space, dual mode high thrust/low thrust, or versatile propellant NTR. The triple payoff is excellent, even if all three options would pan out below expectations. If only one option reaches its potential, it could make the other two still worth their investment. If all three options meet full expectations, the triple payoff is a space propulsion jackpot which makes concern about the initial investment ludicrous as well as open up the solar system to expedient exploration.

Willoughby, Alan J.↗
NASA NTRS1992

A case of poor substructure diagnostics

The NASTRAN Manuals in the substructuring area are all geared toward instant success, but the solution paths are fraught with many traps for human error. Thus, the probability of suffering a fatal abort is high. In such circumstances, the necessity for diagnostics that are user friendly is paramount. This paper is written in the spirit of improving the diagnostics as well as the documentation in one area where the author felt he was backed into a blind corner as a result of his having committed a data oversight. This topic is aired by referring to an analysis of a particular structure. The structure, under discussion, used a number of local coordinate systems that simplified the preparation of input data. The principle features of this problem are introduced by reference to a series of figures.

Butler, Thomas G.↗
DOE OSTI2022

Tuning the Properties of Nanocomposites by Trapping Them in Deep Metastable States

We report the interfacial region formed in a polymer matrix around nanoparticles (NPs) controls many macroscopic properties of polymer nanocomposites (PNCs). However, understanding the factors controlling structure and properties of interfacial region remains a challenge. We demonstrated that the initial trapping of polymer chains at surfaces of NPs in solution strongly affects the macroscopic properties of PNCs. The most surprising result is that the differences in properties of PNCs persist even after an extremely long thermal annealing time. We ascribe the observed changes to the formation of interfacial layer that is trapped in a deep metastable state already in solution. Furthermore, presented analysis suggests that PNC equilibration time is defined by the chain desorption time that can be extremely long and, in some cases, even not accessible on a reasonable experimental time scale. These results highlight the importance of polymer solution concentrations on the formation of interfacial layer and the macroscopic properties of PNCs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evaluation and mitigation of trace 210Pb contamination on copper surfaces

Clean materials are required to construct and operate many low-background physics experiments. High-purity copper has found broad use because of its physical properties and availability. In this paper, we describe methods to assay and mitigate Pb-210 contamination on copper surfaces, such as from exposure to environmental radon or coming from bulk impurities. We evaluated the efficacy of wet etching on commercial samples and observed that Po-210 contamination from the copper bulk does not readily pass into solution. During the etch, the polonium appears to trap at the copper-etchant boundary, such that it is effectively concentrated at the copper surface. We observed a different behavior for Pb-210; high-sensitivity measurements of the alpha emissivity versus time indicate the lowest level of Pb-210 contamination ever reported for a commercial copper surface: 0 +/- 12 nBq/cm2 (1-sigma). Additionally, we have demonstrated the effectiveness of mitigating trace Pb-210 and Po-210 surface backgrounds using custom, high-purity electroplating techniques. These approaches were evaluated utilizing assays performed with an XIA UltraLo-1800 alpha spectrometer.

radon, copper, copper cleaning, dark matter, Pb-21↗
NASA NTRS1976

Flight data analysis and further development of variable-conductance heat pipes

Continuing efforts in large gains in heat-pipe performance are reported. It was found that gas-controlled variable-conductance heat pipes can perform reliably for long periods in space and effectively provide temperature stabilization for spacecraft electronics. A solution was formulated that allows the control gas to vent through arterial heat-pipe walls, thus eliminating the problem of arterial failure under load, due to trace impurities of noncondensable gas trapped in an arterial bubble during priming. This solution functions well in zero gravity. Another solution was found that allows priming at a much lower fluid charge. A heat pipe with high capacity, with close temperature control of the heat source and independent of large variations in sink temperature was fabricated.

Enginer, J. E.↗