Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scaling Validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

On the use of DSCOVR EPIC to monitor the visible calibration stability of polar orbiting imagers to improve the next edition of the CERES climate data record.

The NASA CERES project has provided the climate quality observed TOA and computed surface fluxes to the scientific community. CERES instruments are onboard the Terra, Aqua, NPP, and NOAA-20 spacecraft. CERES uses MODIS and VIIRS imagers to retrieve cloud properties needed to convert CERES footprint radiance observations into fluxes using empirically derived angular directional models obtained during early CERES record. CERES utilizes geostationary sensors to infer the regional diurnal fluxes in between Terra and Aqua CERES observations. The imagers are also used to radiometrically scale the geostationary sensors (GEO) radiances to the imager calibration reference to ensure that the GEO derived cloud properties and broadband TOA fluxes are consistent in both space and time. Both the imager and GEO retrieved cloud properties are used to compute the surface fluxes. The Aqua-MODIS, SNPP-VIIRS, and NOAA-20 VIIRS afternoon imagers will also need to be radiometrically scaled to the same common calibration reference. Although all three imagers employ onboard solar diffusers, the calibration is not consistent over time due to instrument anomalies and ageing of the onboard calibrators. The CERES imager and GEO calibration group (IGCG) has been tasked to remove the imager channel calibration drifts for the next CERES reprocessing effort. The team will rely primarily on deep convective clouds, desert, and polar ice invariant targets to monitor the imager channel stability. The team uses ray-matched radiance pairs to radiometrically scale the SNPP and NOAA-20 VIIRS sensors to Aqua-MODIS. The radiometric scaling is further validated using geostationary imagers as transfer radiometers. The DSCOVR satellite was launched on February 25, 2015 and orbits around the L1 Lagrange point directly between the Earth and the sun. The EPIC instrument onboard DSCOVR employs a CCD array to image the Earth approximately every 2-hours. The EPIC sensor contains no onboard calibration systems. However, multiple inter-calibration studies have shown that the EPIC imager is very stable in time. This is likely due to the DSCOVR satellite being located about a 1.5M km from the Earth, where very little Earth reflected solar radiation degrades the optics. The excellent radiometric stability of EPIC allows the CERES IGCG to utilize the EPIC observations as a stable reference for monitoring the calibration stability of the three afternoon imagers, as well as to validate the radiometric scaling factors between them. Examples of the imager relative calibration using EPIC before and after radiometric scaling will be shown along with the results from the use of invariant targets to remove imager calibration drifts.

DSCOVR-EPIC↗
NASA NTRS2002

The Southern African Regional Science Initiative (SAFARI 2000). Dry-Season Campaign: An Overview

The Southern African Regional Science Initiative (SAFARI 2000) is an international science project investigating the southern African earth-atmosphere-human system. The experiment was conducted over a two-year period March 1999 - March 2001. The dry season field campaign (August-Steptember 2000) was the most intensive activity and involving over 200 scientists from 18 different nations. The main objectives of this campaign were to characterize and quantify the biogenic, pyrogenic and anthropogenic aerosol and trace gas emissions and their transport and transformations in the atmosphere and to validate the NASA Earth Observing System (EOS) satellite Terra within a scientific context. Five aircraft, namely two South African Weather Service aircraft, University of Washington CV-580, the UK Meteorological Office C-130 and the NASA ER-2, with different altitude capabilities, participated in the campaign. Additional airborne sampling of southern African air masses that had moved downwind of the subcontinent was conducted by the CSIRO over Australia. Multiple observations were taken in various sectors for a variety of synoptic conditions. Flight missions were designed to maximize synchronous over-flights of the NASA TERRA satellite platform, above regional ground validation and science targets. Numerous smaller-scale ground validation activities took place throughout the region during the campaign period.

Swap, R. J.↗
NASA NTRS2020

GISS Model E2.2: A Climate Model Optimized for the Middle Atmosphere. Part 2: Validation of Large-Scale Transport and Evaluation of Climate Response

Here we examine the large‐scale transport characteristics of the new ``Middle Atmosphere" NASA Goddard Institute for Space Studies climate model (E2.2). First we evaluate the stratospheric transport circulation in historical atmosphere‐only simulations integrated with interactive trace gas and aerosol chemistry. Compared to lower vertical resolution model versions, E2.2 exhibits improved tropical ascent and older stratospheric mean ages that are more consistent with observed values. In the troposphere, poleward transport to the Arctic and interhemispheric mean ages in E2.2 are comparable to models participating in the Chemistry Climate Modeling Initiative. In addition to validating E2.2 we also assess its ``transport sensitivity" using the coupled atmosphere‐ocean abrupt 4xCO2 and transient 1%CO2 simulations submitted to the Coupled Model Intercomparison Project, Phase 6, along with a 2xCO2 simulation used to evaluate the linearity of the transport circulation's response to increased CO2. We show that decreases (increases) in a stratospheric mean age (idealized surface loss) tracer scale linearly with increased lower stratospheric upwelling, which also increases linearly with warming tropical sea surface temperatures (SSTs). Abrupt 2xCO2 and 4xCO2 experiments constrained with (fixed) pre‐industrial SSTs are also used to quantify the relative importance of rapid adjustments versus SST feedbacks to the transport circulation responses in the model. Finally, sensitivity experiments are presented to illustrate the impact of changes in the convective parameterization on stratospheric transport.

GISS Model E2.2↗
NASA NTRS1995

Validating spatial structure in canopy water content using geostatistics

Heterogeneity in ecological phenomena are scale dependent and affect the hierarchical structure of image data. AVIRIS pixels average reflectance produced by complex absorption and scattering interactions between biogeochemical composition, canopy architecture, view and illumination angles, species distributions, and plant cover as well as other factors. These scales affect validation of pixel reflectance, typically performed by relating pixel spectra to ground measurements acquired at scales of 1m(exp 2) or less (e.g., field spectra, foilage and soil samples, etc.). As image analysis becomes more sophisticated, such as those for detection of canopy chemistry, better validation becomes a critical problem. This paper presents a methodology for bridging between point measurements and pixels using geostatistics. Geostatistics have been extensively used in geological or hydrogeolocial studies but have received little application in ecological studies. The key criteria for kriging estimation is that the phenomena varies in space and that an underlying controlling process produces spatial correlation between the measured data points. Ecological variation meets this requirement because communities vary along environmental gradients like soil moisture, nutrient availability, or topography.

Sanderson, E. W.↗
NASA NTRS1978

Critical phenomena in a low gravity environment

Various types of critical point phenomena are discussed including the gas-liquid phase transition of a fluid, the spontaneous magnetization of a ferromagnet below the Curie temperature, and structural phase transitions of solid materials. The interrelation of thermodynamic properties by scaling laws is considered noting theories for the validity of scaling laws and the principle of universality. Gravity effects are reviewed noting that in earth-based experiments the phenomena are significantly influenced by the earth's gravitational field and that fluid samples that are spatially homogeneous cannot be realized near the gas-liquid critical point.

Sengers, J. V.↗
NASA NTRS1998

Real-Time Sensor Validation System Developed

Real-time sensor validation improves process monitoring and control system dependability by ensuring data integrity through automated detection of sensor data failures. The NASA Lewis Research Center, Expert Microsystems, and Intelligent Software Associates have developed an innovative sensor validation system that can automatically detect automated sensor failures in real-time for all types of mission-critical systems. This system consists of a sensor validation network development system and a real-time kernel. The network development system provides tools that enable systems engineers to automatically generate software that can be embedded within an application. The sensor validation methodology captured by these tools can be scaled to validate any number of sensors, and permits users to specify system sensitivity. The resulting software reliably detects all types of sensor data failures.

Zakrajsek, June F.↗
NASA NTRS2008

Validation through Full-scale Flight Exploration

Full scale flight test forces designers to address real-world issues. Provides high-visibility demonstration. Adds credibility that adaptation technology can be a viable design option. Helps to separate the real from the imagined.

Bosworth, John T.↗
NASA NTRS2009

Validation through Full-Scale Flight Exploration

Objectives: a) Regain Stable Platform: 1) Metrics analogous to stability margins needed for adaptive control systems; 2) Avoid adverse structural interactions. b) Maneuverability: 1) Control vehicle within new constraints; 2) Respect structural limitations; 3) Inform pilot of new performance limitations. c) Provide ability to safely land airplane: 1) Develop safest recovery trajectory.

Bosworth, John T.↗
NASA NTRS2017

Integrating Bioregenerative Foods into the Exploration Spaceflight Food System

Food, the nutrition it provides, and the eating experiences surrounding it, are central to performance, health, and psychosocial wellbeing on long duration spaceflight missions. Exploration missions will require a spaceflight food system that is safe, nutritious, and acceptable for up to five years, possibly without cold storage. Many of the processed and packaged spaceflight foods currently used on the International Space Station will not retain acceptable quality or required levels of key nutrients under these conditions. The addition of bioregenerative produce to exploration missions may become an important countermeasure to the nutritional gaps and a resource to support psychosocial health. Bioregenerative produce will be central to establishment of Earth-independence as exploration extends deeper into space. However, bioregenerative foods introduce food safety and scarcity risks that must be eliminated prior to crew reliance on these systems. The pathway to Earth independence will require small-scale integration and validation prior to large scale bioregenerative dependence. Near term exploration missions offer the opportunity to establish small scale supplemental salad crop and fruit systems and validate infrastructure reliability, nutritional potential, and the psychosocial benefits necessary to promote further bioregenerative integration.

Douglas, Grace L.↗
NASA NTRS1993

Measured acoustic characteristics of ducted supersonic jets at different model scales

A large-scale (about a 25x enlargement) model of the Georgia Tech Research Institute (GTRI) hardware was installed and tested in the Propulsion Systems Laboratory of the NASA Lewis Research Center. Acoustic measurements made in these two facilities are compared and the similarity in acoustic behavior over the scale range under consideration is highlighted. The study provide the acoustic data over a relatively large-scale range which may be used to demonstrate the validity of scaling methods employed in the investigation of this phenomena.

Jones, R. R., III↗
NASA NTRS2000

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick Glauert Goldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗
NASA NTRS2000

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick GlauertGoldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗
NASA NTRS2006

Latest Developments in SLD Scaling

Scaling methods have been shown previously to work well for super cooled large droplet (SLD) main ice shapes. However, feather sizes for some conditions have not been well represented by scale tests. To determine if there are fundamental differences between the development of feathers for appendix C and SLD conditions, this study used time-sequenced photographs, viewing along the span of the model during icing sprays. An airspeed of 100 kt, cloud water drop MVDs of 30 and 140 microns, and stagnation freezing fractions of 0.30 and 0.50 were tested in the NASA Glenn Icing Research Tunnel using an unswept 91-cm-chord NACA0012 airfoil model mounted at 0deg AOA. The photos indicated that the feathers that developed in a distinct region downstream of the leading-edge ice determined the horn location and angle. The angle at which feathers grew from the surface were also measured; results are shown for an airspeed of 150 kt, an MVD of 30 microns, and stagnation freezing fractions of 0.30 to 0.60. Feather angles were found to depend strongly on the stagnation freezing fraction, and were independent of either chordwise position on the model or time into the spray. Feather angles also correlated well with horn angles. For these tests, there did not appear to be fundamental differences between the physics of SLD and appendix C icing; therefore, for these conditions similarity parameters used for appendix C scaling appear to be valid for SLD scaling as well. Further investigation into the cause for the large feather structures observed for some SLD conditions will continue.

Tsao, Jen-Ching↗
NASA NTRS2006

In-Flight Validation of a Pilot Rating Scale for Evaluating Failure Transients in Electronic Flight Control Systems

Engineering development and qualification of a Research Flight Control System (RFCS) for the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) JUH-60A has motivated the development of a pilot rating scale for evaluating failure transients in fly-by-wire flight control systems. The RASCAL RFCS includes a highly-reliable, dual-channel Servo Control Unit (SCU) to command and monitor the performance of the fly-by-wire actuators and protect against the effects of erroneous commands from the flexible, but single-thread Flight Control Computer. During the design phase of the RFCS, two piloted simulations were conducted on the Ames Research Center Vertical Motion Simulator (VMS) to help define the required performance characteristics of the safety monitoring algorithms in the SCU. Simulated failures, including hard-over and slow-over commands, were injected into the command path, and the aircraft response and safety monitor performance were evaluated. A subjective Failure/Recovery Rating (F/RR) scale was developed as a means of quantifying the effects of the injected failures on the aircraft state and the degree of pilot effort required to safely recover the aircraft. A brief evaluation of the rating scale was also conducted on the Army/NASA CH-47B variable stability helicopter to confirm that the rating scale was likely to be equally applicable to in-flight evaluations. Following the initial research flight qualification of the RFCS in 2002, a flight test effort was begun to validate the performance of the safety monitors and to validate their design for the safe conduct of research flight testing. Simulated failures were injected into the SCU, and the F/RR scale was applied to assess the results. The results validate the performance of the monitors, and indicate that the Failure/Recovery Rating scale is a very useful tool for evaluating failure transients in fly-by-wire flight control systems.

Kalinowski, Kevin F.↗
NASA NTRS2022

A Global Evaluation of IMERG Precipitation Occurrence Using SMAP Detected Soil Moisture Change

A globally consistent ground validation method for remotely sensed precipitation products is crucial for building confidence in these products. This study develops a new methodology to validate the IMERG precipitation products through the use of SMAP soil moisture changes as a proxy for precipitation occurrence. Using a standard 2x2 contingency table method, preliminary results provide confidence in SMAP’s ability to be utilized as a validation tool for IMERG as results are comparable to previous validation studies. However, the method allows for an overestimate of false alarm frequency due to light precipitation events that can evaporate before the subsequent SMAP overpass and changes in overpass-to-overpass SMAP soil moisture that are within the range of SMAP uncertainty. To counter these issues, a 3x3 contingency table is used to reduce noise and extract more signal from the detection method. Through the use of this novel approach, the validation method produces a global mean POD of 0.64 and global mean FAR of 0.40, the first global-scale ground validation skill scores for the IMERG products. Advancing the method to validate precipitation quantity and the development of a real-time validation for the IMERG Early product are the crucial next developments.

Precipitation↗
NASA NTRS1981

The development of methods for predicting and measuring distribution patterns of aerial sprays

A set of relationships used to scale small sized dispersion studies to full size results are experimentally verified and, with some qualifications, basic deposition patterns are presented. In the process of validating these scaling laws, the basic experimental techniques used in conducting such studies both with and without an operational propeller were developed. The procedures that evolved are outlined in some detail. The envelope of test conditions that can be accommodated in the Langley Vortex Research Facility, which were developed theoretically, are verified using a series of vortex trajectory experiments that help to define the limitations due to wall interference effects for models of different sizes.

Ormsbee, A. I.↗
NASA NTRS2010

Sorbent, Sublimation, and Icing Modeling Methods: Experimental Validation and Application to an Integrated MTSA Subassembly Thermal Model

This paper details the validation of modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly, developed for use in a Portable Life Support System (PLSS). The first core component in the subassembly is a sorbent bed, used to capture and reject metabolically produced carbon dioxide (CO2). The sorbent bed performance can be augmented with a temperature swing driven by a liquid CO2 (LCO2) sublimation heat exchanger (SHX) for cooling the sorbent bed, and a condensing, icing heat exchanger (CIHX) for warming the sorbent bed. As part of the overall MTSA effort, scaled design validation test articles for each of these three components have been independently tested in laboratory conditions. Previously described modeling methodologies developed for implementation in Thermal Desktop and SINDA/FLUINT are reviewed and updated, their application in test article models outlined, and the results of those model correlations relayed. Assessment of the applicability of each modeling methodology to the challenge of simulating the response of the test articles and their extensibility to a full scale integrated subassembly model is given. The independent verified and validated modeling methods are applied to the development of a MTSA subassembly prototype model and predictions of the subassembly performance are given. These models and modeling methodologies capture simulation of several challenging and novel physical phenomena in the Thermal Desktop and SINDA/FLUINT software suite. Novel methodologies include CO2 adsorption front tracking and associated thermal response in the sorbent bed, heat transfer associated with sublimation of entrained solid CO2 in the SHX, and water mass transfer in the form of ice as low as 210 K in the CIHX.

Bower, Chad↗
NASA NTRS1979

The development of methods for predicting and measuring distribution patterns of aerial sprays

The capability of conducting scale model experiments which involve the ejection of small particles into the wake of an aircraft close to the ground is developed. A set of relationships used to scale small-sized dispersion studies to full-size results are experimentally verified and, with some qualifications, basic deposition patterns are presented. In the process of validating these scaling laws, the basic experimental techniques used in conducting such studies, both with and without an operational propeller, were developed. The procedures that evolved are outlined. The envelope of test conditions that can be accommodated in the Langley Vortex Research Facility, which were developed theoretically, are verified using a series of vortex trajectory experiments that help to define the limitations due to wall interference effects for models of different sizes.

Ormsbee, A. I.↗