Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SURFACE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Effects of surface pressures and streamline metrics on the calculation of laminar heating rates

The effect of streamline geometry and pressure distributions on surface heating rates is examined for slender, spherically blunted cones. The modifications to the approximate aeroheating code include a curve fit of pressures computed by an Euler solution over a range of Mach numbers and cone angles. The streamline geometry is then found using the surface pressures and inviscid surface properties. Previously, streamlines were determined using the inviscid properties at the edge of the boundary layer when accounting for the effects of entropy-layer swallowing. Streamline calculations are now based on inviscid surface conditions rather than boundary-layer edge properties. However, the heating rates are calculated using inviscid properties at the edge of the boundary layer. Resulting heating rates compare favorably with solutions from the viscous-shock-layer equations.

Riley, Christopher J.↗
NASA NTRS2021

Skin Friction Extracted from Surface Pressure in Incident Shock-Wave/Boundary-Layer Interaction

High-resolution skin-friction fields are extracted from pressure-sensitive paint (PSP) data obtained in shock-wave/boundary-layer interaction (SWBLI). The method of extracting skin friction from surface pressure is described, including the fundamental relation between skin friction and surface pressure, the variational method, error analysis, and an approximate iterative method. The proposed method is based on a coupling relation between skin friction and surface pressure, where the boundary enstrophy flux is suitably modeled or approximated. This method is applied to unsteady PSP data obtained in incident SWBLIs at Mach 2.5 for different Reynolds numbers, revealing the skin-friction structures of the flows: particularly, the separation bubble induced by the incident shock wave. The extracted results are in good agreement with the data obtained by the surface-stress-sensitive film.

skin friction↗
NASA NTRS1980

Surface pressure measurements at two tips of a model helicopter rotor in hover

Surface pressures were measured near the tip of a hovering single-bladed model helicopter rotor with two tip shapes. The rotor had a constant-chord, untwisted blade with a square, flat tip which could be modified to a body-of-revolution tip. Pressure measurements were made on the blade surface along the chordwise direction at six radial stations outboard of the 94 percent blade radius. Data for each blade tip configuration were taken at blade collective pitch angles of 0, 6.18 and 11.4 degrees at a Reynolds number of 736,000 and a Mach number of 0.25 both based on tip speed. Chordwise pressure distributions and constant surface pressure contours are presented and discussed.

Gray, R. B.↗
NASA NTRS1981

A study of real jet effects on the surface pressure distribution induced by a jet in a crossflow

A study of jet exit profile, exit Mach number, swirl and turbulence level on jet-induced loadings for jets exhausting from a surface into a crossflow is presented. The importance of each of these real jet characteristics is assessed using available data. Where adequate surface pressure distribution data are available, a correlation method to predict surface pressure for a jet exhausting from an infinite flat plate is used either to attempt to develop a correlation based on the real jet characteristics or to model the effects of that characteristic. Data comparisons are presented for selected cases. Also, a summary of information on surface pressure distribution data for jet exhausting from flat plates into a subsonic crossflow is presented.

Perkins, S. C., Jr.↗
NASA NTRS1999

Simulations of the Surface Pressure Tides on Mars Incorporating New MOLA Topography Data

Simulations of surface pressure tides on Mars have been conducted previously with the NASA Ames Mars General Circulation Model (MGCM), as well as by Wilson and Hamilton. In the case of the MGCM, annual simulations with realistic (Viking-derived) dust loading have been reasonably successful at reproducing observed tides at the Viking Lander sites. One obvious discrepancy between observed and simulated tides is the amplification found in the model's diurnal tidal amplitude around L(sub s) 90. The observations show no such amplification. We report here on recent simulations of the surface pressure tide on Mars conducted with the MGCM and with the newly acquired MOLA topography data. The data is provided at 1deg x 1deg resolution, and is used by the MGCM at 7.5deg x 9deg resolution. The vertical domain of the MGCM extends to around 80 km. In the simulations reported in, the vertical domain extended to around 50 km, and the Consortium topography dataset was used. Additional information is contained in the original extended abstract.

Bridger, A. F. C.↗
NASA NTRS1979

Determination of tropical cyclone surface pressure and winds from satellite microwave data

An approach to the problem of deducing wind speed and pressure around tropical cyclones is presented. The technique, called the Surface Wind Inference from Microwave data (SWIM technique, uses satellites microwave sounder data to measure upper tropospheric temperature anomalies which may then be related to surface pressure anomalies through the hydrostatic and radiative transfer equations. Surface pressure gradients outside of the radius of maximum wind are estimated for the first time. Future instruments may be able to estimate central pressure with + or - 0/1 kPa accuracy.

Kidder, S. Q.↗
NASA NTRS1991

Unsteady surface pressure measurements on a slender delta wing undergoing limit cycle wing rock

An experimental investigation of slender wing limit cycle motion known as wing rock was investigated using two unique experimental systems. Dynamic roll moment measurements and visualization data on the leading edge vortices were obtained using a free to roll apparatus that incorporates an airbearing spindle. In addition, both static and unsteady surface pressure data was measured on the top and bottom surfaces of the model. To obtain the unsteady surface pressure data a new computer controller drive system was developed to accurately reproduce the free to roll time history motions. The data from these experiments include, roll angle time histories, vortex trajectory data on the position of the vortices relative to the model's surface, and surface pressure measurements as a function of roll angle when the model is stationary or undergoing a wing rock motion. The roll time history data was numerically differentiated to determine the dynamic roll moment coefficient. An analysis of these data revealed that the primary mechanism for the limit cycle behavior was a time lag in the position of the vortices normal to the wing surface.

Arena, Andrew S., Jr.↗
NASA NTRS1959

Surface Pressure Distribution at Hypersonic Speeds for Blunt Delta Wings at Angle of Attack

Surface pressures were measured over a blunt 60 deg delta wing with extended trailing edge at a Mach number of 5.7, a free-stream Reynolds number of 20,000 per inch, and angles of attack from -10 to +10 deg. Aft of four leading-edge thicknesses the pressure distributions evidenced no appreciable three-dimensional effects and were predicted qualitatively by a method described herein for calculation of pressure distribution in two-dimensional flow. Results of tests performed elsewhere on blunt triangular wings were found to substantiate the near two-dimensionality of the flow and were used to extend the range of applicability of the method of surface pressure predictions to Mach numbers of 11.5 in air and 13.3 in helium.

Creager, Marcus O.↗
NASA NTRS1986

An experimental study of the properties of surface pressure fluctuations for separating turbulent boundary layers

Noise generated by helicopter and turbomachine rotors is a nuisance that designers would like to predict and to minimize within other design constraints. A key element for the noise calculation procedure is knowledge relating the flowfield structure to the surface pressure fluctuation structure. Surface pressure fluctuation data for zero-pressure-gradient and accelerating turbulent boundary layers were obtained. The zero-pressure-gradient turbulent boundary layers were examined with freestream velocities of 72 and 105 fps. Mean and fluctuation velocity profiles and streamwise velocity spectra and wavespeeds were obtained for momentum thickness Reynolds numbers up to 18000 for the zero-pressure-gradient case and up to 4000 for the favorable-pressure-gradient case. The wall shearing stress was estimated from a Clauser plot of the near wall data. It is clear that turbulent pressure fluctuations are produced by turbulent velocity fluctuations. Detailed simultaneous measurements of all of these fluctuations are needed to determine in more detail the structural relationships between velocity and pressure fields. Although some measurements were made for unseparated flows, none were made for separated flows.

Simpson, Roger L.↗
NASA NTRS1985

Flight measurements of surface pressures on a flexible supercritical research wing

A flexible supercritical research wing, designated as ARW-1, was flight-tested as part of the NASA Drones for Aerodynamic and Structural Testing Program. Aerodynamic loads, in the form of wing surface pressure measurements, were obtained during flights at altitudes of 15,000, 20,000, and 25,000 feet at Mach numbers from 0.70 to 0.91. Surface pressure coefficients determined from pressure measurements at 80 orifice locations are presented individually as nearly continuous functions of angle of attack for constant values of Mach number. The surface pressure coefficients are also presented individually as a function of Mach number for an angle of attack of 2.0 deg. The nearly continuous values of the pressure coefficient clearly show details of the pressure gradient, which occurred in a rather narrow Mach number range. The effects of changes in angle of attack, Mach number, and dynamic pressure are also shown by chordwise pressure distributions for the range of test conditions experienced. Reynolds numbers for the tests ranged from 5.7 to 8.4 x 1,000,000.

Eckstrom, C. V.↗
NASA NTRS1979

Fluctuating surface pressure and acoustic radiation for subsonic normal jet impingement

Results are presented from an experimental study of fluctuating surface pressures and far-field noise produced by a subsonic circular jet impinging normally to a large, rigid, flat surface. The tests were performed in an anechoic room for jet Mach numbers from 0.54 to 0.85 and for jet-to-surface heights from 5 to 10 jet diameters. Space and time correlations of surface pressure indicated a radially spreading, decaying pressure field having correlation lengths on the order of one-half the jet diameter with convection speeds between 0.5 and 0.6 of the peak wall-jet velocity. Overall sound pressure level varied as the eighth power of the jet velocity. Large-scale orderly structures in the flow were suggested by the noise spectra which peaked at a Strouhal number of about 0.3. In addition, an analytical formulation was given to approximate the apparent noise-producing regions of the flow in terms of cross-correlations and cross-spectra between the surface and far-field measurements. Results pointed to the impingement region of the flow field as the major contribution to the far-field impingement noise.

Preisser, J. S.↗
NASA NTRS1973

Measurements of surface-pressure fluctuations on the XB-70 airplane at local Mach numbers up to 2.45

Measurements of surface-pressure fluctuations were made at two locations on the XB-70 airplane for nine flight-test conditions encompassing a local Mach number range from 0.35 to 2.45. These measurements are presented in the form of estimated power spectral densities, coherence functions, and narrow-band-convection velocities. The estimated power spectral densities compared favorably with wind-tunnel data obtained by other experimenters. The coherence function and convection velocity data supported conclusions by other experimenters that low-frequency surface-pressure fluctuations consist of small-scale turbulence components with low convection velocity.

Lewis, T. L.↗
NASA NTRS1992

Unsteady wing surface pressures in the wake of a propeller

The unsteady nature of the propeller slipstream interacting with a wing has been studied by flow visualization and unsteady wing surface pressure measurements. Flow visualization was performed by marking the propeller tip vortex with smoke. Unsteady wing surface pressures were measured by traversing a wing instrumented with a chordwise array of 16 microphones in a spanwise direction through the propeller wake. This work yielded information on the motion of the propeller wake as it passes over the wing. As the propeller wake passed over the wing: the propeller tip vortex experienced an inviscid interaction at the leading edge; viscous action at the leading edge severed the propeller tip vortex; the propeller tip vortex experienced significant spanwise and chordwise displacements and then deformed in order to reconnect at the trailing edge; axial velocity in the vortex core caused the helical vortex to thicken or stretch near the wing surface; and, the magnitude of the pressure fluctuations decreased in magnitude with distance traveled along the chord.

Johnston, R. T.↗
NASA NTRS1955

Effect of high rotor pressure-surface diffusion on performance of a transonic turbine

The subject turbine was investigated to determine the effect of high rotor pressure-surface diffusion on turbine performance. A comparison of the subject turbine with the most efficient transonic turbine in the present series of investigations showed that the efficiency of the subject turbine was almost as high, the suction-surface diffusion parameter was about the same, and the solidity was reduced by 36 percent. Because the loss per blade increased greatly with an increase in pressure-surface diffusion, the latter is also considered to be an important design consideration.

Miser, James W↗