SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
New fundamental technique of reliability prediction for semiconductor diodes based on realistic mathematical models can be applied to component failure rate prediction including mechanical degradation, electrical degradation, environmental stress factors, and electrical load stress factors.
Literature survey, analytic formulations, and test rig designs for cavitating inducers in rocket engine turbopumps
For abstract, see N74-19673.
The potential gain in buckling resistance is explored by using the curvilinear format with a plate containing a centrally located circular hole and subjected to a uniaxial compressive load. The buckling loads for a uniform stress loading and simple support boundary conditions were examined. The method of analysis is outlined for the buckling improvement study. Several designs that represent an improvement over a baseline quasi-isotropic design (a design that is quite good for buckling resistance) are discussed. The tensile load of these designs is examined. A recommended design is presented that not only shows an improved buckling capacity, but also shows improved tensile performance. Follow-on activities are also discussed.
An analysis is developed which combines the Ritz and collocation methods for the stability solution of an anisotropic plate with a cutout and elastically restrained edges. Results are presented which agree closely with experiment for isotropic and orthotropic materials. Results are also given for restrained anisotropic plates with circular holes loaded in compression and shear. Difference is noted in the critical buckling loads between displacement and stress loaded panels as hole size is increased. Clamping is also seen to affect the trends in buckling associated with hole size.
Several topology optimization problems are conducted within the ribs and spars of a wing box. It is desired to locate the best position of lightening holes, truss/cross-bracing, etc. A variety of aeroelastic metrics are isolated for each of these problems: elastic wing compliance under trim loads and taxi loads, stress distribution, and crushing loads. Aileron effectiveness under a constant roll rate is considered, as are dynamic metrics: natural vibration frequency and flutter. This approach helps uncover the relationship between topology and aeroelasticity in subsonic transport wings, and can therefore aid in understanding the complex aircraft design process which must eventually consider all these metrics and load cases simultaneously.
No abstract available
Constant load, stressed oxidation testing was performed on T-300 C/SiC composites with a SiC seal coat. Test conditions included temperatures ranging from 350 C to 1500 C at stresses of 69 MPa and 172 MPa (10 and 25 ksi). The coupon subjected to stressed oxidation at 550 C/69 MPa for 25 hours had a room temperature residual strength one-half that of the as-received coupons. The coupon tested at the higher stress and all coupons tested at higher temperatures failed in less than 25 hr. Microstructural analysis of the fracture surfaces, using SEM (scanning electron microscopy), revealed the formation of reduced cross-sectional fibers with pointed tips. Analysis of composite cross-sections show pathways for oxygen ingress. The discussion will focus on fiber/matrix interphase oxidation and debonding as well as the formation and implications of the fiber tip morphology.
Viscoplastic models that use the Armstrong and Frederick (1966) kinematic hardening relationship are known to generally overpredict the observed accumulation of ratchet strains. The reason for this behavior is a consequence of the mathematics used to describe Hooke's law and the evolution equations for plastic strain and back stress. Conditions for ratchetting exist whenever there is a cycle-averaged mean stress present over a cyclic loading path. Two types of controlled loading paths are often studied: cyclic relaxation is the ratchet mechanism associated with displacement (strain) control, while cyclic creep is the ratchet mechanism associated with load (stress) control. Overcoming the possible adverse trends in predicted ratchetting behavior is a difficult task, and how one ought to go about doing this is not yet completely clear. We therefore choose to discuss the mathematical cause of ratchetting and how it has been dealt with to date, but make no attempt to correct this flaw.
The determination of the stress distribution in the inner lap of double-lap, double-bolt joints using photoelastic models of the joint is discussed. The principal idea is to fabricate the inner lap of a photoelastic material and to use a photoelastically sensitive material for the two outer laps. With this setup, polarized light transmitted through the stressed model responds principally to the stressed inner lap. The model geometry, the procedures for making and testing the model, and test results are described.
Acclerated fatigue-life testing of heat-exchanger tubes simplified by technique that substitutes mechanical side load for thermally-generated axisymmetric stress. Load amplitudes adjusted to produce strains equivalent to those produced by anticipated thermal stress.
Abstract Cu-based superelastic shape memory alloys are promising for low-stress elastocaloric cooling. We have synthesized bulk alloys of 68Cu–16Al–16Zn under different conditions in order to promote its grain growth and enhance its elastocaloric properties. High-temperature x-ray diffraction of untreated 68Cu–16Al–16Zn alloy showed that the phase boundary between the α + β mixed phases and the high temperature phase ( β phase) was between 973 K and 1023 K. Based on this result, the 68Cu–16Al–16Zn alloy was heated and cooled in a furnace repeatedly between 773 K and 1173 K. The maximum grain size after heat treatment of the ingot rolled to 67% reached 11.1 mm. The latent heat of the martensitic transformation after grain growth was 6.3 J g −1 , which is higher than the previously reported value for the compound. The stress–strain curve of 68Cu–16Al–16Zn rolled to 67% rolling with cyclical heat treatments showed a maximum stress of 106 MPa at 4.5% strain, with adiabatic temperature change of 5.9 K in heating during stress loading and 5.6 K in cooling in stress removal. Furthermore, no fatigue in the stress–strain behavior was observed up to at least 60 000 mechanical cycles at 2% strain.
The results of a series of experiments performed in the evaluation of nondestructive tensile testing of chip and wire bonds are presented. Semiconductor devices were subjected to time-temperature excursions, static-load life testing and multiple pre-stressing loads to determine the feasibility of a nondestructive tensile testing approach. The report emphasizes the importance of the breaking angle in determining the ultimate tensile strength of a wire bond, a factor not generally recognized nor implemented in such determinations.
Method for calculating stress due to acceleration loading: 1) Part has been designed by FEA and hand calculation in one critical loading direction judged by the analyst; 2) Maximum stress can be due to loading in another direction; 3) Analysis procedure to be presented determines: a) The maximum Mises stress at any point; and b) The direction of maximum loading associated with the "stress". Concept of Mass Acceleration Curves (MAC): 1) Developed by JPL to perform preliminary structural sizing (i.e. Mariners, Voyager, Galileo, Pathfinder, MER,...MSL); 2) Acceleration of physical masses are bounded by a curve; 3) G-levels of vibro-acoustic and transient environments; 4) Convergent process before the couple loads cycle; and 5) Semi-empirical method to effectively bound the loads, not a simulation of the actual response.
External loading procedures for stress corrosion tests of aluminum alloys, and ferrous and nickel alloys
A series of fracture tests were conducted on Middle-crack tension M(T) and compact tension C(T) specimens to determine the effects of specimen type, specimen width, notch tip sharpness and buckling on the fracture behavior of cracked thin sheet (0.04 inch thick) 2024-T3 aluminum alloy material. A series of M(T) specimens were tested with three notch tip configurations: (1) a fatigue pre-cracked notch, (2) a 0.010-inch-diameter wire electrical discharge machined (EDM) notch, and (3) a EDM notch sharpened with a razor blade. The test procedures are discussed and the experimental results for failure stress, load vs. crack extension and the material stress-strain response are reported.
The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is one example of a proposed vehicle that would perform science independently of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design for these vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and fuselage designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.
The successful demonstration of powered flight on Mars by Ingenuity has led to the development of next generation Martian rotorcraft. As technology advances from a technology demonstrator to possible expanded planetary science investigations, the potential to fly a high payload carrying rotorcraft relies on the capability to analyze and validate the structural integrity of the vehicle in addition to the rotor aerodynamic performance. The Mars Science Helicopter (MSH), a next generation hexacopter concept, is an example of a proposed vehicle that would perform science investigations independent of a land-based vehicle. To ensure the feasibility and viability of MSH mission performance, it is critical to mature the structural design of vehicle concepts to bridge the gap between the best practices of the spacecraft and aircraft communities. MSH was analyzed under operational and 26G quasi-static launch loads with different rotor arm and frame designs. Structural analysis results showed that rotor arms could be stiffened for significantly improved structural performance with minimal mass penalty, while the rotorcraft frame exhibited a more complex relationship between mass and launch load stresses due to the mass-dependent launch loads.