Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Analysis of oscillatory pressure data including dynamic stall effects

The dynamic stall phenomenon was examined in detail by analyzing an existing set of unsteady pressure data obtained on an airfoil oscillating in pitch. Most of the data were for sinusoidal oscillations which penetrated the stall region in varying degrees, and here the effort was concentrated on the chordwise propagation of pressure waves associated with the dynamic stall. It was found that this phenomenon could be quantified in terms of a pressure wave velocity which is consistently much less than free-stream velocity, and which varies directly with frequency. It was also found that even when the stall region has been deeply penetrated and a substantial dynamic stall occurs during the downstroke, stall recovery near minimum incidence will occur, followed by a potential flow behavior up to stall inception.

Carta, F. O.↗
NASA NTRS1975

Chordwise propagation of dynamic stall cells on an oscillating airfoil

The dynamic stall phenomenon was examined in detail by analyzing a set of unsteady pressure data obtained on an airfoil oscillating in pitch. These data were for sinusoidal oscillations which penetrated the stall region in varying degrees, and here the effort was concentrated on the chordwise propagation of pressure waves associated with the dynamic stall. It was found that this phenomenon could be quantified in terms of a pressure wave velocity which is consistently much less than free-stream velocity, and which varies directly with frequency. It was also found that even when the stall region has been deeply penetrated and a substantial dynamic stall occurs during the downstroke, stall recovery near minimum incidence will occur, followed by a potential flow behavior up to stall inception.

Carta, F. O.↗
NASA NTRS1977

Analysis of the development of dynamic stall based on oscillating airfoil experiments

The effects of dynamic stall on airfoils oscillating in pitch were investigated by experimentally determining the viscous and inviscid characteristics of the airflow on the NACA 0012 airfoil and on several leading-edge modifications. The test parameters included a wide range of frequencies, Reynolds numbers, and amplitudes-of-oscillation. Three distinct types of separation development were observed within the boundary layer, each leading to classical dynamic stall. The NACA 0012 airfoil is shown to stall by the mechanism of abrupt turbulent leading-edge separation. A detailed step-by-step analysis of the events leading to dynamic stall, and of the results of the stall process, is presented for each of these three types of stall. Techniques for flow analysis in the dynamic stall environment are discussed. A method is presented that reduces most of the oscillating airfoil normal force and pitching-moment data to a single curve, independent of frequency or Reynolds number.

Carr, L. W.↗
NASA NTRS1980

A study of stall deterrent systems for general aviation aircraft

Stall deterrent concepts for general aviation aircraft have been investigated using simulation studies and flight test experiments. It was found that the simulator was suitable for the development of deterrent system concepts, but the simulator was unacceptable for pilot evaluation of system effectiveness under typical stall/spin accident conditions. A Cessna 319 was outfitted with sensors, servoactuators, and analog control logic necessary to investigate a wide range of stall deterrent systems. It was found that an acoustic stall sensor and an error control law were sufficient for stall deterrence. The pitch intervention control system prevented aircraft stall for all aircraft configurations and pilot inputs. The variable up elevator stop concept was found to be effective for slow decelerations to aircraft stall. The stall deterrent systems were evaluated by four professional pilots and three low time pilots.

Bennett, A. G.↗
NASA NTRS1983

Flow mechanism and experimental investigation of a rotating stall in transonic compressors

The flow characteristics of the rotating stall in compressors is studied, and a flow model is developed along with a theoretical calculation method based on vortex theory. A detailed theoretical calculation is completed for a two dimensional flow field in a transonic rotor in a rotating stall, and the result is in good agreement with experimental findings. The oscillograms of time-varying stall characteristic parameters recorded for the onset, growth, and cessation processes of rotating stall are analyzed, and some new flow phenomena deserving of further investigation are discovered. These include serious separation of individual blades, often preceding the onset of rotating stall in compressors with very small blade-camber angles, and periodical variation of the circumferential width of the stall cell with time, accompanied by periodical oscillation of the width of the stall cell in the radial direction of the blade. The circumferential and radial oscillation frequencies are the same.

Yajun, L.↗
NASA NTRS1954

Experimental Investigation of Acceleration Characteristics of a Turbojet Engine Including Regions of Surge and Stall for Control Applications

The acceleration characteristics, in the region of maximum acceleration and compressor stall and surge, of an axial-flow turbojet engine with a fixed-area exhaust nozzle were determined by subjecting the engine to fuel flow steps, ramps, and ramps with a sine wave superimposed. From the data obtained, the effectiveness of an optimalizer type of control for this engine was evaluated. At all speeds above 40 percent of rated, a maximum acceleration was not obtained until the engine reached the point of stall or surge. A sharp drop, as high as 80 percent of maximum, in acceleration then occurred as the compressor entered surge of stall. With the maximum acceleration occurring at the point of surge or stall, the optimalizer-type control could not prevent the engine from entering surge or stall. Effective operation of the control may still be possible by sensing the sharp drop in acceleration experienced at the point of stall or surge and using this signal to limit fuel flow. The success of this type of operation would depend on the magnitude of the stall-recovery hysteresis.

Stiglic, Paul M↗
NASA NTRS1994

Interferometric investigations of compressible dynamic stall over a transiently pitching airfoil

The compressible dynamic stall flowfield over a NACA 0012 airfoil transiently pitching from 0 to 60 deg at a constant rate under compressible flow conditions has been studied using real-time interferometry. A quantitative description of the overall flowfield, including the finer details of dynamic stall vortex formation, growth, and the concomitant changes in the airfoil pressure distribution, has been provided by analyzing the interferograms. For Mach numbers above 0.4, small multiple shocks appear near the leading edge and are present through the initial stages of dynamic stall. Dynamic stall was found to occur coincidentally with the bursting of the separation bubble over the airfoil. Compressibility was found to confine the dynamic stall vortical structure closer to the airfoil surface. The measurements show that the peak suction pressure coefficient drops with increasing freestream Mach number, and also it lags the steady flow values at any given angle of attack. As the dynamic stall vortex is shed, an anti-clockwise vortex is induced near the trailing edge, which actively interacts with the post-stall flow.

Chandrasekhara, M. S.↗
NASA NTRS1996

Dimension Determination of Precursive Stall Events in a Single Stage High Speed Compressor

This paper presents a study of the dynamics for a single-stage, axial-flow, high speed compressor core, specifically, the NASA Lewis rotor stage 37. Due to the overall blading design for this advanced core compressor, each stage has considerable tip loading and higher speed than most compressor designs, thus, the compressor operates closer to the stall margin. The onset of rotating stall is explained as bifurcations in the dynamics of axial compressors. Data taken from the compressor during a rotating stall event is analyzed. Through the use of a box-assisted correlation dimension methodology, the attractor dimension is determined during the bifurcations leading to rotating stall. The intent of this study is to examine the behavior of precursive stall events so as to predict the entrance into rotating stall. This information may provide a better means to identify, avoid or control the undesirable event of rotating stall formation in high speed compressor cores.

Bright, Michelle M.↗
NASA NTRS1997

Study of the Unsteady Flow Features on a Stalled Wing

The occurrence of large scale structures in the post stall flow over a rectangular wing at high angles of attack was investigated in a small-scale subsonic wind tunnel. Mean and time dependent measurements within the separated flow field suggest the existence of two distinct angle of attack regimes beyond wing stall. The shallow stall regime occurs over a narrow range of incidence angles (2-3 deg.) immediately following the inception of leading edge separation. In this regime, the principal mean flow structures, termed stall cells, are manifested as a distinct spanwise periodicity in the chordwise extent of the separated region on the model surface with possible lateral mobility not previously reported. Within the stall cells and on the wing surface, large amplitude pressure fluctuations occur with a frequency much lower than anticipated for bluff body shedding, and with minimum effect in the far wake. In the deep stall regime, stall cells are not observed and the separated region near the model is relatively free of large amplitude pressure disturbances.

Yon, Steven A.↗
NASA NTRS2000

Dynamic Stall Characteristics of Drooped Leading Edge Airfoils

Helicopters in high-speed forward flight usually experience large regions of dynamic stall over the retreating side of the rotor disk. The rapid variations in the lift and pitching moments associated with the stall process can result in vibratory loads, and can cause fatigue and failure of pitch links. In some instances, the large time lag between the aerodynamic forces and the blade motion can trigger stall flutter. A number of techniques for the alleviation of dynamic stall have been proposed and studied by researchers. Passive and active control techniques have both been explored. Passive techniques include the use of high solidity rotors that reduce the lift coefficients of individual blades, leading edge slots and leading edge slats. Active control techniques include steady and unsteady blowing, and dynamically deformable leading edge (DDLE) airfoils. Considerable amount of experimental and numerical data has been collected on the effectiveness of these concepts. One concept that has not received as much attention is the drooped-leading edge airfoil idea. It has been observed in wind tunnel studies and flight tests that drooped leading edge airfoils can have a milder dynamic stall, with a significantly milder load hysteresis. Drooped leading edge airfoils may not, however, be suitable at other conditions, e.g. in hover, or in transonic flow. Work needs to be done on the analysis and design of drooped leading edge airfoils for efficient operation in a variety of flight regimes (hover, dynamic stall, and transonic flow). One concept that is worthy of investigation is the dynamically drooping airfoil, where the leading edge shape is changed roughly once-per-rev to mitigate the dynamic stall.

Sankar, Lakshmi N.↗
NASA NTRS1999

Development of Hub Corner Stall and Its Influence on the Performance of Axial Compressor Blade Rows

A detailed investigation has been performed to study hub corner stall phenomena in compressor blade rows. Three-dimensional flows in a subsonic annular compressor stator and in a transonic compressor rotor have been analyzed numerically by solving the Reynolds-averaged Navier-Stokes equations. The numerical results and the existing experimental data are interrogated to understand the mechanism of compressor hub comer stall. Both the measurements and the numerical solutions for the stator indicate that a strong twister-like vortex is formed near the rear part of the blade suction surface. Low-momentum fluid inside the hub boundary layer is transported toward the suction side of the blade by this vortex. On the blade suction surface near the hub, this vortex forces fluid to move against the main flow direction and a limiting stream surface is formed near the hub. The formation of this vortex is the main mechanism of hub corner stall. When the aerodynamic loading is increased, the vortex initiates further upstream, which results in a larger corner stall region. For the transonic compressor rotor studied in this paper, the numerical solution indicates that a mild hub corner stall exists at 100 percent rotor speed. The hub corner stall, however, disappears at the reduced blade loading, which occurs at 60 percent rotor design speed. The present study demonstrates that hub comer stall is caused by a three-dimensional vortex system and that it does not seem to be correlated with a simple diffusion factor for the blade row.

Hah, C.↗
NASA NTRS2003

Task I: A Computational Model for Short Wavelength Stall Inception and Development In Multi-Stage Compressors

A computational model is presented for simulating axial compressor stall inception and development via disturbances with length scales on the order of several (typically about three) blade pitches. The model was designed for multi-stage compressors in which stall is initiated by these short wavelength disturbances, also referred to as spikes. The inception process described is fundamentally nonlinear, in contrast to the essentially linear behavior seen in so-called modal stall inception . The model was able to capture the following experimentally observed phenomena: (1) development of rotating stall via short wavelength disturbances, (2) formation and evolution of localized short wavelength stall cells in the first stage of a mismatched compressor, (3) the switch from long to short wavelength stall inception resulting from the re-staggering of the inlet guide vane, (4) the occurrence of rotating stall inception on the negatively sloped portion of the compressor characteristic. Parametric investigations indicated that (1) short wavelength disturbances were supported by the rotor blade row, (2) the disturbance strength was attenuated within the stators, and (3) the reduction of inter-blade row gaps can suppress the growth of short wavelength disturbances. It is argued that each local component group (rotor plus neighboring stators) has its own instability point (i.e. conditions at which disturbances are sustained) for short wavelength disturbances, with the instability point for the compressor set by the most unstable component group.

Suder, Kenneth↗
NASA NTRS1946

Preliminary Tests of a Buffet Stall-Warning Device on a 1/5-Scale Model of the Republic XP-84 Airplane

During the first flight tests of the Republic XP-84 airplane it was discovered that there was a complete lack of stall warning. A short series of development tests of a suitable stall-warning device for the airplane was therefore made on a 1/5-scale model in the Langley 300 MPH 7- by 10-foot tunnel. Two similar stall-warning devices, each designed to produce early root stall which would provide a buffet warning, were tested. It appeared that either device would give a satisfactory buffet warning in the flap-up configuration, at the cost of an increase of 8 or 10 miles per hour in minimum speed. Although neither device seemed to give a true buffet warning in the flaps-down configuration, it appeared that either device would improve the flaps-down stalling characteristics by lessening the severity of the stall and by maintaining better control at the stall. The flaps-down minimum-speed increase caused by the devices was only 1 or 2 miles per hour.

Tucker, Warren A.↗
NASA NTRS1998

Jet Injection Used to Control Rotating Stall in a High-Speed Compressor

In a joint effort between the Massachusetts Institute of Technology (MIT) and the NASA Lewis Research Center, a new technology was demonstrated to identify and control rotating stall and surge in a single-stage, high-speed compressor. Through the use of highvelocity, high-frequency jet injectors, the instabilities of surge and stall were controlled in a high-speed compressor rig. Through the use of active stall control, modal instabilities that normally occur in the pressure measurements prior to stall were normalized and the range of the compressor was extended. Normally the events of rotating stall and surge instabilities limit the operation of the aeroengine compressor to a region below the surge line. To enhance the performance of the compressor, the Lewis/MIT team used active stall control methods to extend the normal operation of the compressor beyond the original stall point.

Bright, Michelle M.↗
NASA NTRS2004

Conical Magnetic Bearings Developed for Active Stall Control in Gas Turbine Engines

Active stall control is a current research area at the NASA Glenn Research Center that offers a great benefit in specific fuel consumption by allowing the gas turbine to operate beyond the onset of stall. Magnetic bearings are being investigated as a new method to perform active stall control. This enabling global aviation safety technology would result in improved fuel efficiency and decreased carbon dioxide emissions, as well as improve safety and reliability by eliminating oil-related delays and failures of engine components, which account for 40 percent of the commercial aircraft departure delays. Active stall control works by perturbing the flow in front of the compressor stage such that it cancels the pressure wave, which causes the compressor to go into stall. Radial magnetic bearings are able to whirl the shaft so that variations in blade tip leakage would flow upstream causing a perturbation wave that could cancel the rotating stall cell. Axial or thrust magnetic bearings cannot be used to cancel the surge mode in the compressor because they have a very low bandwidth and thus cannot modulate at a high enough frequency. Frequency response is limited because the thrust runner cannot be laminated. To improve the bandwidth of magnetic thrust bearings, researchers must use laminations to suppress the eddy currents. A conical magnetic bearing can be laminated, resulting in increased bandwidth in the axial direction. In addition, this design can produce both radial and thrust force in a single bearing, simplifying the installation. The proposed solution combines the radial and thrust bearing into one design that can be laminated--a conical magnetic bearing. The new conical magnetic bearing test rig, funded by a Glenn fiscal year 2002 Director's Discretionary Fund, was needed because none of the existing rigs has an axial degree of freedom. The rotor bearing configuration will simulate that of the main shaft on a gas turbine engine. One conical magnetic bearing replaces the ball bearing in front of the compressor, and the second replaces the roller bearing behind the burner. The rig was made operational to 10,000 rpm under Smart Efficient Components funding, and both position and current adaptive vibration control have been demonstrated. Upon program completion, recommendations will be made as to the efficacy of the conical magnetic bearing for active stall control.

Trudell, Jeffrey J.↗
NASA NTRS1955

Preliminary Results of the Determination of Inlet-Pressure Distortion Effects on Compressor Stall and Altitude Operating Limits of the J57-P-1 Turbojet Engine

During an investigation of the J57-P-1 turbojet engine in the Lewis altitude wind tunnel, effects of inlet-flow distortion on engine stall characteristics and operating limits were determined. In addition to a uniform inlet-flow profile, the inlet-pressure distortions imposed included two radial, two circumferential, and one combined radial-circumferential profile. Data were obtained over a range of compressor speeds at an altitude of 50,000 and a flight Mach number of 0.8; in addition, the high- and low-speed engine operating limits were investigated up to the maximum operable altitude. The effect of changing the compressor bleed position on the stall and operating limits was determined for one of the inlet distortions. The circumferential distortions lowered the compressor stall pressure ratios; this resulted in less fuel-flow margin between steady-state operation and compressor stall. Consequently, the altitude operating Limits with circumferential distortions were reduced compared with the uniform inlet profile. Radial inlet-pressure distortions increased the pressure ratio required for compressor stall over that obtained with uniform inlet flow; this resulted in higher altitude operating limits. Likewise, the stall-limit fuel flows required with the radial inlet-pressure distortions were considerably higher than those obtained with the uniform inlet-pressure profile. A combined radial-circumferential inlet distortion had effects on the engine similar to the circumferential distortion. Bleeding air between the two compressors eliminated the low-speed stall limit and thus permitted higher altitude operation than was possible without compressor bleed.

Wallner, L. E.↗
NASA NTRS2013

Analysis of Low-Speed Stall Aerodynamics of a Swept Wing with Laminar-Flow Glove

Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a GIII aircraft s swept wing modified with a laminar-flow wing glove. The stall aerodynamics of the gloved wing were analyzed and compared with the unmodified wing for the flight speed of 120 knots and altitude of 2300 ft above mean sea level (MSL). The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First AIAA CFD High-Lift Prediction Workshop. It was found that the Star-CCM+ CFD code can produce results that are within the scattering of other CFD codes considered at the workshop. In particular, the Star-CCM+ CFD code was able to predict wing stall for the AIAA wing-body geometry to within 1 degree of angle of attack as compared to benchmark wind-tunnel test data. Current results show that the addition of the laminar-flow wing glove causes the gloved wing to stall much earlier than the unmodified wing. Furthermore, the gloved wing has a different stall characteristic than the clean wing, with no sharp lift drop-off at stall for the gloved wing.

Bui, Trong↗
NASA NTRS2014

Analysis of Low-Speed Stall Aerodynamics of a Swept Wing with Laminar-Flow Glove

Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a GIII aircraft's swept wing modified with a laminar-flow wing glove. The stall aerodynamics of the gloved wing were analyzed and compared with the unmodified wing for the flight speed of 120 knots and altitude of 2300 ft above mean sea level (MSL). The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First American Institute of Aeronautics and Astronautics (AIAA) CFD High-Lift Prediction Workshop. It was found that the Star-CCM+ CFD code can produce results that are within the scattering of other CFD codes considered at the workshop. In particular, the Star-CCM+ CFD code was able to predict wing stall for the AIAA wing-body geometry to within 1 degree of angle of attack as compared to benchmark wind-tunnel test data. Current results show that the addition of the laminar-flow wing glove causes the gloved wing to stall much earlier than the unmodified wing. Furthermore, the gloved wing has a different stall characteristic than the clean wing, with no sharp lift drop-off at stall for the gloved wing.

Bui, Trong T.↗