Results for “STAGNATION PRESSURE” — Page 3

NASA NTRS1998

Inlet Performance Analysis Code Developed

The design characteristics of an inlet very much depend on whether the inlet is to be flown at subsonic, supersonic, or hypersonic speed. Whichever the case, the primary function of an inlet is to deliver free-stream air to the engine face at the highest stagnation pressure possible and with the lowest possible variation in both stagnation pressure and temperature. At high speeds, this is achieved by a system of oblique and/or normal shock waves, and possibly some isentropic compression. For both subsonic and supersonic flight, current design practice indicates that the inlet should deliver the air to the engine face at approximately Mach 0.45. As a result, even for flight in the high subsonic regime, the inlet must retard (or diffuse) the air substantially. Second, the design of an inlet is influenced largely by the compromise between high performance and low weight. This compromise involves tradeoffs between the mission requirements, flight trajectory, airframe aerodynamics, engine performance, and weight-all of which, in turn, influence each other. Therefore, to study the effects of some of these influential factors, the Propulsion System Analysis Office of the NASA Lewis Research Center developed the Inlet Performance Analysis Code (IPAC). This code uses oblique shock and Prandtl-Meyer expansion theory to predict inlet performance. It can be used to predict performance for a given inlet geometric design such as pitot, axisymmetric, and two-dimensional. IPAC also can be used to design preliminary inlet systems and to make subsequent performance analyses. It computes the total pressure, the recovery, the airflow, and the drag coefficients. The pressure recovery includes losses associated with normal and oblique shocks, internal and external friction, the sharp lip, and diffuser components. Flow rate includes captured, engine, spillage, bleed, and bypass flows. The aerodynamic drag calculation includes drags associated with spillage, cowl lip suction, wave, bleed, and bypass.

Jules, Kenol↗

NASA NTRS1972

Computer program of data reduction procedures for facilities using CO2-N2-O2-Ar equilibrium real-gas mixtures

Data reduction procedures for determining free-stream and post-normal-shock flow conditions are presented. These procedures are applicable to flows of CO2, N2, O2, Ar, or mixtures of these gases and include the effects of dissociation and ionization. The assumption of thermochemical equilibrium free-stream and post-normal-shock flow is made. Although derived primarily to meet the immediate needs of an expansion tube of a hot gas radiation research facility, these procedures are applicable to any supersonic or hypersonic test facility using these gases or mixtures thereof. The data reduction procedures are based on combinations of three of the following flow parameters measured in the immediate vicinity of the test section: (1) stagnation pressure behind normal shock, (2) free-stream static pressure, (3) stagnation-point heat-transfer rate, (4) free-stream velocity, and (5) free-stream density. Thus, these procedures do not depend explicitly upon measured or calculated upstream flow parameters. The procedures are incorporated into a single computer program written in FORTRAN IV language. A listing of this computer program is presented, along with a description of the inputs required and a sample of the data printout.

Miller, C. G., III↗

NASA NTRS1961

A Technique for Determining the Nozzle-Flow Properties of Air in an Equilibrium, Nonequilibrium, or Frozen State

One of the problems associated with the development of high-enthalpy hypersonic test facilities hos been the determination of nozzle flow properties. This note presents a technique for determining the flow properties of air in an equilibrium, non-equilibrium, or frozen state using two test section measurements. A knowledge of two stagnation properties is required before the technique can be applied. The stagnation pressure can be measured, and reference 1 offers a method for determining stagnation enthalpy. Results of the calculations using the method of reference 1 are presented in reference 2 in a chart (chart 21) which can be readily used to determine the stagnation enthalpy from measurements of stagnation pressure, mass flow of air through the tunnel, and throat diameter.

Hayman, Lovick O.↗

NASA NTRS1960

Real-Gas Correction Factors for Hypersonic Flow Parameters in Helium

The real-gas hypersonic flow parameters for helium have been calculated for stagnation temperatures from 0 F to 600 F and stagnation pressures up to 6,000 pounds per square inch absolute. The results of these calculations are presented in the form of simple correction factors which must be applied to the tabulated ideal-gas parameters. It has been shown that the deviations from the ideal-gas law which exist at high pressures may cause a corresponding significant error in the hypersonic flow parameters when calculated as an ideal gas. For example the ratio of the free-stream static to stagnation pressure as calculated from the thermodynamic properties of helium for a stagnation temperature of 80 F and pressure of 4,000 pounds per square inch absolute was found to be approximately 13 percent greater than that determined from the ideal-gas tabulation with a specific heat ratio of 5/3.

Erickson, Wayne D.↗

NASA NTRS1979

Inhibition of solar wind impingement on Mercury by planetary induction currents

Analytic methods are developed for taking into account finite planetary conductivity in modeling departures from equilibrium of a magnetospheric boundary caused by solar wind stagnation pressure variations. Using the lowest suggested value of the planetary dipole moment (2.4 x 10 to the 22nd G cu cm), it is estimated that a minimum pressure of about 38 P sub 0 (where P sub 0 is the external stagnation pressure in the steady state) is required to force the standoff distance down to the subsolar surface of Mercury if the pressure change persists for at least 1 day. This value is 4.3 times that which would be predicted if Mercury had no core, and it is larger than the maximum pressure predicted at Mercury's orbit (about 25 P sub 0) on the basis of hourly averaged solar wind statistics at 1 AU.

Hood, L. L.↗

NASA NTRS1994

Light Weight Ceramic Ablators for Mars Follow-on Mission Vehicle Thermal Protection System

New Light Weight Ceramic Ablators (LCA) were produced by using ceramic and carbon fibrous substrates, impregnated with silicone and phenolic resins. The special infiltration techniques (patent pending) were developed to control the amount of organic resins in the highly porous fiber matrices so that the final densities of LCA's range from 0.22 to 0.24 g/cc. This paper presents the thermal and ablative performance of the Silicone Impregnated Reusable Ceramic Ablators (SIRCA) in simulated entry conditions for Mars-Pathfinder in the Ames 60 MW Interaction Heating Facility (I HF). Arc jet test results yielded no evidence of char erosion and mass loss at high stagnation pressures to 0.25 atm. Minimal silica melt was detected on surface char at a stagnation pressure of 0.31 atm. Four ceramic substrates were used in the production of SIRCA's to obtain the effective of boron oxide present in substrate so the thermal performance of SIRCA's. A sample of SIRCA was also exposed to the same heating condition for five cycles and no significant mass loss or recession was observed. Tensile testing established that the SIRCA tensile strength is about a factor of two higher than that of the virgin substrates. Thermogravimetric Analysis (TGA) of the char in nitrogen and air showed no evidence of free carbon in the char. Scanning Electron Microscopy of the post test sample showed that the char surface consists of a fibrous structure that was sealed with a thin layer of silicon oxide melt.

Tran, Huy K.↗

NASA NTRS1987

Low thrust viscous nozzle flow fields prediction

An existing Navier-Stokes code (PARC2D) was used to compute the nozzle flow field. Grids were generated by the interactive grid generator codes TBGG and GENIE. All computations were made on the NASA/MSFC CRAY X-MP computer. Comparisons were made between the computations and MSFC in-house wall pressure measurements for CO2 flow through a conical nozzle having an area ratio of 40. Satisfactory agreements exist between the computations and measurements for different stagnation pressures of 29.4, 14.7, and 7.4 psia, at stagnation temperature of 1060 R. However, agreements did not match precisely near the nozzle exit. Several reasons for the lack of agreement are possible. The computational code assumes a constant gas gamma, whereas the gamma i.e. the specific heat ratio for CO2 varied from 1.22 in the plenum chamber to 1.38 at the nozzle exit. The computations also assumes adiabatic and no-slip walls. Both assumptions may not be correct. Finally, it is possible that condensation occurs during the nozzle expansion at the low stagnation pressure. The next phase of the work will incorporate variable gamma and slip wall boundary conditions in the computational code and develop a more accurate computer code.

Liaw, Goang-Shin↗

NASA NTRSDate not supplied

A TPS Design Analysis of Entry Probe Delivery from Orbit for Ice Giant Missions

Previous investigation of direct delivery of a probe into Neptune’s atmosphere showed said approach to be challenging due to high stagnation pressures and heat loads. Entering at a high entry flight path angle (EFPA) results in stagnation pressure beyond current Heatshield for Extreme Entry Environment Technology (HEEET) qualification, while entering at a lower EFPA results in higher heat loads, leading to required HEEET thicknesses beyond manufacturing capabilities. Aerocapture is an enticing alternative entry scenario because it enables a fast trip and the placement of a payload in orbit around Neptune that can also reach Triton. Here, we investigate entry conditions associated with delivering a probe from orbit to assess feasibility. We consider whether 1) this entry scenario results in reasonable conditions, and 2) HEEET single insulating layer (mid-density carbon phenolic, 3MDCP) can be used to decrease mass, risk, and cost.

H. S. Alpert↗

NASA NTRSDate not supplied

A TPS Design Analysis of Entry Probe Delivery from Orbit for Ice Giant Missions

Previous investigation of direct delivery of a probe into Neptune’s atmosphere showed said approach to be challenging due to high stagnation pressures and heat loads. Entering at a high entry flight path angle (EFPA) results in stagnation pressure beyond current Heatshield for Extreme Entry Environment Technology (HEEET) qualification, while entering at a lower EFPA results in higher heat loads, leading to required HEEET thicknesses beyond manufacturing capabilities. Aerocapture is an enticing alternative entry scenario because it enables a fast trip and the placement of a payload in orbit around Neptune that can also reach Triton. Here, we investigate entry conditions associated with delivering a probe from orbit to assess feasibility. We consider whether 1) this entry scenario results in reasonable conditions, and 2) HEEET single insulating layer (mid-density carbon phenolic, 3MDCP) can be used to decrease mass, risk, and cost.

Hannah S. Alpert↗

NASA NTRS1976

Analysis and testing of two-dimensional vented Coanda ejectors with asymmetric variable area mixing sections

The analysis of asymmetric, curved (Coanda) ejector flow has been completed using a finite difference technique and a quasi-orthogonal streamline coordinate system. The boundary layer type jet mixing analysis accounts for the effect of streamline curvature in pressure gradients normal to the streamlines and on eddy viscosities. The analysis assured perfect gases, free of pressure discontinuities and flow separation and treated three compound flows of supersonic and subsonic streams. Flow parameters and ejector performance were measured in a vented Coanda flow geometry for the verification of the computer analysis. A primary converging nozzle with a discharge geometry of 0.003175 m x 0.2032 m was supplied with 0.283 cu m/sec of air at about 241.3 KPa absolute stagnation pressure and 82 C stagnation temperature. One mixing section geometry was used with a 0.127 m constant radius Coanda surface. Eight tests were run at spacing between the Coanda surface and primary nozzle 0.01915 m and 0.318 m and at three angles of Coanda turning: 22.5 deg, 45.0 deg, and 75.0 deg. The wall static pressures, the loci of maximum stagnation pressures, and the stagnation pressure profiles agree well between analytical and experimental results.

Maroti, L. A.↗

NASA NTRS1975

Measurement of density and temperature in a hypersonic turbulent boundary layer using the electron beam fluorescence technique

Mean density and temperature fluctuations were measured across the turbulent, cooled-wall boundary layer in a continuous hypersonic (Mach 9.4) wind tunnel in air, using the nitrogen fluorescence excited by a 50 kV electron beam. Data were taken at three values of the tunnel stagnation pressure, the corresponding free stream densities being equivalent to 1.2, 4.0, and 7.4 torr at room temperature, and the boundary layer thicknesses about 4.0, 4.5, and 6.0 inches. The mean temperature and density profiles were similar to those previously determined in the same facility by conventional probes (static and pitot pressure, total temperature). A static pressure variation of about 50% across the boundary layer was found, the shape of the variation changing somewhat for the three stagnation pressure levels. The quadrupole model for rotational temperature spectra gave closer agreement with the free stream isentropic level (approximately 44 K) than the dipole model.

Mcronald, A. D.↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Karl T Edquist↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Supersonic Retropropulsion↗

NASA NTRS1960

Basic Pressure Measurements at a Mach Number of 1.43 on a Thin 45 deg Sweptback Highly Tapered Wing with Systematic Spanwise Twist Variations

Pressure distributions are presented on four wings: an untwisted wing to serve as a reference, and wings with linear, quadratic and cubic twist variations along the span. All the twisted wings had 0deg twist at the 10-percent-semispan station and 6deg twist at the tip. The tests were made at a Mach number of 1.43 and covered an angle-of-attack range from -4deg to 20deg. The average Reynolds number based on the wing mean aerodynamic chord was 2.9 x 10(exp 6) during tests at a stagnation pressure of 1.0 atmosphere and 1.5 x 10(exp 6) during tests at a stagnation pressure of 0.5 atmosphere.

Mugler, John P., Jr.↗

NASA NTRS1976

Axial flow rotor unsteady response to circumferential inflow distortions

The unsteady response of an axial flow fan rotor to steady, circumferential inflow velocity and stagnation pressure distortions is assessed by two different methods. These are: (1) investigation of the unsteady normal force and pitching moment on a chordwise element of a rotor blade; and (2) investigation of the variation of the stagnation pressure distortion between the inlet and exit of the rotor. Experimental measurements of these unsteady characteristics are presented as a function of the geometry of the rotor -- stagger angle, solidity and steady angle of incidence -- for sinusoidally varying circumferential distortions with different numbers of distortion cycles. These measurements are compared with several theoretical analyses. While these comparisons indicate some of the deficiencies which exist in the theories, the existence of an unsteady cascade effect and the ability of the theories to adequately predict the trend of the unsteady response due to variations in reduced frequency, rotor stagger angle, solidity and mean incidence angle is clearly demonstrated.

Bruce, E. P.↗

NASA NTRS1996

Rayleigh scattering measurements in supersonic facilities

Using a narrow-band, pulsed, ArF excimer laser and a single-intensified CCD camera, planar laser Rayleigh scattering measurements were performed to obtain quantitative density measurements both in the free stream and in a model flow field. These measurements were conducted in the 15-inch, Mach 6 high temperature facility at NASA Langley Research Center. This facility is capable of achieving stagnation temperatures up to 700 K (800 F) over a range of stagnation pressures from 0.35 to 2.07 MPa (50 to 300 psia). The high temperature capability of this facility eliminates the clustering effect observed in earlier Mach 6 studies, and allows quantitative density measurements in the free stream over a range of stagnation pressures from 0.35 to 1.75 MPa (50 to 250 psia). Model flow field measurements were obtained on 38.1 mm diameter cylinder. Measurement locations include the free stream, the region behind the bow shock in front of the model, and the region behind the model including the wake. The densities deduced from the Rayleigh scattering measurements in the model flow field are compared with CFD computations. Measurement uncertainties and the detection limit are discussed.

Shirinzadeh, B.↗

NASA NTRS1993

Experimentation in the low-density plume of a simulated electrothermal thruster for computer code validation

Pressures and flow angles are measured in the plume of a 20 deg half-angle, conical nozzle in vacuum with Pitot tubes and conical probes. The area of measurement in the plume ranges from the nozzle exit plane to 480 mm axially downstream and from the plume centerline to 60 mm radially. The nozzle has an exit-to-throat area ratio of 100:1 and a throat diameter of 3.2 mm. The nozzle flow exhausts to a vacuum of order 10(exp -2) Pa to simulate a resistojet (an electrothermal rocket of less than 1 N of thrust) operating in space. Experimental data are given for flows of nitrogen at 55 and 68 mg/s, stagnation temperatures between 695 and 921 K, and stagnation pressures ranging from 5600 to 7100 Pa. Data are also given for argon at a rate of 68 mg/s, a stagnation temperature of 648 K, and stagnation pressures of 4500, 4750, and 4770 Pa. Measurements in the nitrogen plume are compared with computational results from a direct-simulation Monte Carlo method.

Meissner, Dana L.↗

NASA NTRS2007

Wall Boundary Layer Measurements for the NASA Langley Transonic Dynamics Tunnel

Measurements of the boundary layer parameters in the NASA Langley Transonic Dynamics tunnel were conducted during extensive calibration activities following the facility conversion from a Freon-12 heavy-gas test medium to R-134a. Boundary-layer rakes were mounted on the wind-tunnel walls, ceiling, and floor. Measurements were made over the range of tunnel operation envelope in both heavy gas and air and without a model in the test section at three tunnel stations. Configuration variables included open and closed east sidewall wall slots, for air and R134a test media, reentry flap settings, and stagnation pressures over the full range of tunnel operation. The boundary layer thickness varied considerably for the six rakes. The thickness for the east wall was considerably larger that the other rakes and was also larger than previously reported. There generally was some reduction in thickness at supersonic Mach numbers, but the effect of stagnation pressure, and test medium were not extensive.

Wieseman, Carol D.↗