High efficiency of seaplanes
A table is presented which includes data for calculating the index of efficiency. The author uses this data to conclude that seaplanes cannot be considered inferior to terrestrial airplanes.
Pegna, G↗
SEARCH · Engineering Papers
Results for “SEAPLANES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Shape and strength of seaplane under-structures with special regard to seaworthiness
This report presents experiments and calculations for the purpose of determining the landing gear requirements upon the water. Moving pictures are given which furnish data and also may give both the magnitude and direction of the forces acting. Different classes of seaplanes are examined and proposals for calculation instructions are given.
Lewe, Victor↗
Air Force and Three Moments for F-5-L Seaplane
A model of the F-5-L seaplane was made, verified, and tested at 40 miles an hour in the 8' x 8' tunnel for lift and drag, also for pitching, yawing and rolling moments. Subsequently, the yawing moment test was repeated with a modified fin. The results are reported without VL scale correction.
Source record↗
Full scale determination of the lift and drag of a seaplane
The speed, barometric pressure, and number of revolutions of the engine of a seaplane were measured, including tests with stopped engine. The mean data obtained are given in the following note; the results of the gliding tests are used for the computation of the lift and drag coefficients, and by making use of them the results of the engine flights are used for the computation of the propeller efficiency.
Munk, Max M↗
F-5-L Boat Seaplane : performance characteristics
Performance characteristics for the F-5-L Boat Seaplane are given. Characteristic curves for the RAF-6 airfoil and the F-5-L wings, parasite resistance and velocity data, engine and propeller characteristics, effective and maximum horsepower, and cruising performance are discussed.
Diehl, W S↗
Static stability of seaplane floats and hulls
Values of lateral and longitudinal metacentric heights for various seaplanes were calculated by means of approximate formulae derived here. The data are given in tabular form. Upon plotting these metacentric heights against the corresponding gross weights, it appears that the metacentric height is approximately a straight line function of the gross weight. For the lateral metacentric height GM = 13 + .002 W and for longitudinal metacentric height GM = 15 + .002 W, GM is in feet and the gross weight (W) is in pounds. Although only approximate, it is thought that the values indicated here are a reliable guide to current practice. It is recommended that the longitudinal and lateral metacentric heights be made equal and of the value given by GM = 15 = .002 W. The proper length or spacing required to satisfy the indicated value may then be obtained from substitution in the approximate formulae for metacentric height.
Diehl, W S↗
The impact on seaplane floats during landing
In order to make a stress analysis of seaplane floats, and especially of the members connecting the floats with the fuselage, it is of great importance to determine the maximum pressure acting on the floats during landing. Here, the author gives a formula for maximum pressures during landing that permits one to apply experimental results to different bodies and different velocities. The author notes that the formula checks very well with experimental results.
Von Karman, TH↗
Tank Tests of Models of Floats for Single-float Seaplanes First Series.
Large models of the Mark V and Mark VI floats used for single float seaplanes (National Advisory Committee for Aeronautics (NACA) models 41-A and 41-B, respectively) were tested in the NACA tank to provide general test data for typical single floats and a basis for possible improvements of their form. The resistance of model 41-B was greater than that of model 41-A, either when free to trim or at the best trim angle for each. The resistance of model 35-B (a pointed step hull tested free to trim) was less than either of the models at the hump speed, greater at intermediate planing speeds, and less at the speeds and loads near get-away, although the spray was generally worse owing to the absence of transverse flare. The results of the fixed-trim tests of model 41-A were cross plotted to obtain data at the angle for zero trimming moment and at the best trim angle. The trims assumed by models 41-A and 41-B, when tested free to trim, were found to be excessive at the hump speed. The corresponding trim of model 35-B was found to be approximately 3 degrees lower because of the lower angle of afterbody keel used in this model, and the maximum hump resistance was 15 percent lower.
Parkinson, J B↗
Hydrodynamic and Aerodynamic Tests of a Family of Models of Seaplane Floats with Varying Angles of Dead Rise - N.A.C.A. Models 57-A, 57-B, and 57-C
Three models of V-bottom floats for twin-float seaplanes (N.A.C.A. models 57-A, 57-B, and 57-C) having angles of dead rise of 20 degrees, 25 degrees, and thirty degrees, respectively, were tested in the N.A.C.A. tank and in the N.A.C.A. 7- by 10-foot wind tunnel. Within the range investigated, the effect of angle of dead rise on water resistance was found to be negligible at speeds up to and including the hump speed, and water resistance was found to increase with angle of dead rise at planing speeds. The height of the spray at the hump speed decreased with increase in angle of dead rise and the aerodynamic drag increased with dead rise. Lengthening the forebody of model 57-B decreased the water resistance and the spray at speeds below the hump speed. Spray strips provided an effective means for the control of spray with the straight V sections used in the series but considerably increased the aerodynamic drag. Charts for the determination of the water resistance and the static properties of the model with 25 degrees dead rise and for the aerodynamic drag of all the models are included for use in design.
Parkinson, John B↗
Seaplanes for commerce
The advantages of using seaplanes for commercial purposes is discussed.
Warner, Edward P↗
NACA Model Investigations of Seaplanes in Waves
The models, apparatus, and instrumentation developed for investigations of the rough-water characteristics of seaplanes in the Langley tanks are described briefly. The results of several investigations to improve these characteristics are combined and summarized. The large effect of waves in take-off resistance is illustrated. The general relationship of the measured quantities of importance to wave length and height are also illustrated.
Parkinson, John B↗
The Supermarine "Southampton" seaplane : observation or bomber
Purchased for the British Air Ministry, the Southampton seaplane uses 2 Napier Lion engines and has a boat hull with outriggers mounted on the wings. It was designed as a military aircraft and can be easily converted to a bomber.
AIRPLANES - SUPERMARINE SOUTHAMPTON (BRIT )↗
Designing seaplane hulls and floats
Experimental data, such as the results of tank tests of models, render it possible to predict, at least in principle, as to how a hull or float of a given shape will comport itself. We will see further along, however, how uncertain these methods are and how they leave room for empiricism, which will reign for a long time yet in seaplane research bureaus.
FLOATS AND HULLS - DESIGN↗
The estimation of maximum load capacity of seaplanes and flying boats
This reports presents a method of calculating time and gross load for take-off of seaplanes and flying boats.
Diehl, Walter S↗
The NACA Tank : A High-speed Towing Basin for Testing Models of Seaplane Floats
This report describes the high-speed model towing basin of the National Advisory Committee for Aeronautics, usually referred to as the NACA Tank. The purpose of this piece of equipment is to enable the Committee to provide information and data regarding the performance of seaplanes on the water analogous to the information furnished concerning the performance of airplanes in the air.
Truscott, Starr↗
Effects of wing flexibility and variable air lift upon wing bending moment during landing impacts of a small seaplane
A smooth-water-landing investigation was conducted with a small seaplane to obtain experimental wing-bending-moment time histories together with time histories of the various parameters necessary for the prediction of wing bending moments during hydrodynamic forcing functions. The experimental results were compared with calculated results which include inertia-load effects and the effects of air-load variation during impact. The responses of the fundamental mode were calculated with the use of the measured hydrodynamic forcing functions. From these responses, the wing bending moments due to the hydrodynamic load were calculated according to the procedure given in R.M. No. 2221. The comparison of the time histories of the experimental and calculated wing bending moments showed good agreement both in phase relationship of the oscillations and in numerical values.
Merten, Kenneth F↗
On the determination of the take-off characteristics of a seaplane
The present paper presents an attempt to coordinate the available theoretical and experimental data on planing surfaces so as to develop an approximate analytical method for the determination of the water resistance of a seaplane without any preliminary towing tests in the tank.
Perelmuter, A↗
Some Ideas on Racing Seaplanes
This report presents the author's designs and construction of various seaplanes to raced in the Schneider Cup. The results of tests are presented as well as discussions of various structures like floats and wings.
Pegna, Giovanni↗