Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Residual distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A Novel Relative Permeability Model for Gas and Water Flow in Hydrate-Bearing Sediments With Laboratory and Field-Scale Application

In a producing gas hydrate reservoir the effective porosity available for fluid flow constantly changes with dissociation of gas hydrate. Therefore, accurate prediction of relative permeability using legacy models (e.g. Brooks-Corey (B-C), van Genuchten, etc.) that were developed for conventional oil and gas reservoirs would require empirical parameters to be calibrated at various S h over its range of variation, but such calibrations are precluded because of lack of experimental relative permeability data. This study proposes a new relative permeability model for gas hydrate-bearing media that is a function of maximum capillary pressure, capillary entry pressure, pore size distribution index, residual saturations, hydrate saturation, and four other constants. The three novel features of the proposed model are: (i) requires fitting its six empirical parameters only once using experimental data from any single S h , and the same set of empirical parameters predict relative permeability at all S h , (ii) includes the effect of capillarity, and (iii) includes the effect of pore-size distribution. From practical standpoint, the model can be used to simulate multiphase flow in gas hydrate-bearing sediments where the proposed relative permeability can account for the evolving hydrate saturation. The proposed model is implemented in a numerical simulator and the wall time required to perform simulations using the proposed model is shown to be similar to the time it takes to run same simulations with the B-C model. The proposed model is a step forward towards achieving the goal of physically accurate modeling of multiphase flow for gas hydrate-bearing sediments that accounts for the effect of gas hydrate saturation change on relative permeability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint’s low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Kinetic Monte Carlo simulations of structural evolution during anneal of additively manufactured materials

Our experiments indicated that upon a post-processing anneal, an additively manufactured 316L stainless steel exhibits cubic grains rather than the conventional equiaxed grains. In this work, we have used kinetic Monte Carlo simulations to explore the origin of these cubic grains. First, we implemented a new kinetic Monte Carlo model in parallel code SPPARKS to simulate grain growth and recrystallization under a residual energy distribution. Our model incorporates physical properties and real-time, as opposed to generic properties and relative time. We further validated that our SPPARKS simulations reproduced the expected kinetic behavior of single-grain evolution. We then used the validated approach to simulate the anneal of an additively manufactured material under the same conditions used in our experiments. We found that the cubic grains can origin from a periodically varying residual energy that may be present in additively manufactured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Residual strain orientation in rolled titanium determined with synchrotron X-ray Laue microdiffraction

Previously, synchrotron X-ray Laue microdiffraction has been used to measure the magnitudes of residual strain in materials. Recently the method was advanced to determine the orientation of the strain ellipsoid and applied to naturally deformed quartzites; however, the deformation history of these quartzites is ambiguous due to their natural origin. Here, in this study, synchrotron X-ray Laue microdiffraction (µXRD) is used to measure the residual strain for the first time in a sample with known stress history, rolled titanium. A deviatoric strain tensor is calculated from each Laue diffraction image collected with two µXRD scans of a rolled titanium sheet in different sample orientations. The principal strain axes are calculated using an eigen decomposition of the deviatoric strain tensors. The results show that the principal axis of compression is aligned with the normal direction of the titanium sheet, and the principal axis of extension is aligned with the rolling direction. Pole figures are used to represent the 3D distribution of residual strain axes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Overall protein structure quality assessment using hydrogen-bonding parameters

Atomic model refinement at low resolution is often a challenging task. This is mostly because the experimental data are not sufficiently detailed to be described by atomic models. To make refinement practical and ensure that a refined atomic model is geometrically meaningful, additional information needs to be used such as restraints on Ramachandran plot distributions or residue side-chain rotameric states. However, using Ramachandran plots or rotameric states as refinement targets diminishes the validating power of these tools. Therefore, finding additional model-validation criteria that are not used or are difficult to use as refinement goals is desirable. Hydrogen bonds are one of the important noncovalent interactions that shape and maintain protein structure. These interactions can be characterized by a specific geometry of hydrogen donor and acceptor atoms. Systematic analysis of these geometries performed for quality-filtered high-resolution models of proteins from the Protein Data Bank shows that they have a distinct and a conserved distribution. Here, it is demonstrated how this information can be used for atomic model validation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Microstructure, Hardness, and Residual Stress of the Dissimilar Metal Weldments of SA508-309L/308L-304L

A dissimilar metal weldment consisting of SA508-309L-308L-304L is widely used in light-water nuclear reactors. These weldments demonstrate dissimilar susceptibility to stress corrosion cracking that are related to the microstructure, properties, and residual stress. In this work, microstructures, hardness, and the residual stress distribution of the dissimilar metal weldments were investigated, with the correlation of increased hardness in the heat-affected zone (HAZ) to the microstructure. 304L HAZ demonstrated similar grain morphology as the base material, and the increase in hardness was primarily attributed to the increased dislocation density. SA508 HAZ demonstrated a change of grain morphology resulting from the different peak temperatures and cooling rates. The increased hardness in the SA508 HAZ was attributed to the refined grain morphology, higher dislocation density, and higher number density of precipitates. A ~ 20–30-μm-wide martensitic zone formed at the fusion boundary of SA508-309L, where Cr-rich carbide precipitates were observed, with the average size and the number density of 44.1 ± 16.9 nm and 1.5 × 10 21 m ₋3 , respectively. In conclusion, residual stress results demonstrated the largest tensile stress at 309L butter, indicating its high cracking susceptibility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Improving stability of ALD ZrN thin film coatings over U-Mo dispersion fuel

Atomic layer deposition (ALD) of ZrN is a candidate technology for coating U-Mo dispersion fuel as a diffusion barrier coating. During the early development stages of the coating the ZrN deposition showed to be mechanically unstable and ultimately resulted in spalling. Based on experimental outcomes it was found that instabillity can be eliminated through the introduction of a thin amorphous (a) Al 2 O 3 interlayer coating deposited in between the ~1-μm thick ZrN and the U-Mo. substrate. To elucidate these findings simulations were performed with density functional theory (DFT) to measure work of adhesions at different interfaces while finite element modeling (FEM) was performed to measure the residual stress distribution. DFT indicated that the ZrN coating deposited over (a)-Al 2 O 3 is ~2.5 times stronger when compared to direct deposition over U or UO 2 substrate. While calculations from FEM recognized; (1) large stress concentrations can originate from the irregularly distributed native surface oxides (UO 2 ) over U-Mo and (2) stress concentrations can be reduced if those surface UO 2 can be modified to a uniform layer (achieved after application of a 8 nm (a)-Al 2 O 3 interlayer). These results provided explanations and confirmed the role played by interlayer in eliminating the original mechanical instability of the ZrN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Improved damage tolerance of SiC-based nuclear fuel cladding with novel multi-layered SiC coating design at 1200 °C

Continuous SiC fibre reinforced SiC matrix composites (SiC f -SiC m ) with monolithic SiC outer coatings are considered as a damage-tolerant cladding design for loss of coolant accident (LOCA) conditions in light water reactors. However, monolithic SiC coatings are brittle and prone to catastrophic failure. In this study, a SiC f -SiC m cladding with a novel multi-layer SiC outer coating (11 sub-layers, ∼260 µm in total thickness) was investigated under C-ring compression at room temperature and 1200 °C in argon environment. Real-time synchrotron X-ray computed tomography (XCT) was employed to capture crack initiation and propagation processes. Compared to conventional monolithic SiC outer coatings, the multi-layer coating structure facilitated crack deflection and bifurcation enhancing its damage tolerance at both temperatures. Despite pre-existing surface cracks, claddings exhibited stable mechanical-performance at both temperatures. These initial cracks did not critically affect the failure processes as they were not aligned with the maximum stress direction. Furthermore, the microstructure, distribution of residual stresses, and local properties of individual components in the material were thoroughly characterized, and compared with open literature on conventional claddings with monolithic outer coatings. These results provide new insights into the failure mechanisms of multi-layer SiC coatings and offer guidance for the future design of accident-tolerant nuclear fuel claddings.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Many-body factorization and position–momentum equivalence of nuclear short-range correlations

While mean-field approximations, such as the nuclear shell model, provide a good description of many bulk nuclear properties, they fail to capture the important effects of nucleon–nucleon correlations such as the short-distance and high-momentum components of the nuclear many-body wave function1. Here, we study these components using the effective pair-based generalized contact formalism and ab initio quantum Monte Carlo calculations of nuclei from deuteron to 40 Ca. We observe a universal factorization of the many-body nuclear wave function at short distance into a strongly interacting pair and a weakly interacting residual system. The residual system distribution is consistent with that of an uncorrelated system, showing that short-distance correlation effects are predominantly embedded in two-body correlations. Spin- and isospin-dependent ‘nuclear contact terms’ are extracted in both coordinate and momentum space for different realistic nuclear potentials. The contact coefficient ratio between two different nuclei shows very little dependence on the nuclear interaction model. These findings thus allow extending the application of mean-field approximations to short-range correlated pair formation by showing that the relative abundance of short-range pairs in the nucleus is a long-range (that is, mean field) quantity that is insensitive to the short-distance nature of the nuclear force.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Transient local secondary structure in the intrinsically disordered C‐term of the Albino3 insertase

Albino3 (Alb3) is an integral membrane protein fundamental to the targeting and insertion of light‐harvesting complex (LHC) proteins into the thylakoid membrane. Alb3 contains a stroma‐exposed C‐terminus (Alb3‐Cterm) that is responsible for binding the LHC‐loaded transit complex before LHC membrane insertion. Alb3‐Cterm has been reported to be intrinsically disordered, but precise mechanistic details underlying how it recognizes and binds to the transit complex are lacking, and the functional roles of its four different motifs have been debated. Using a novel combination of experimental and computational techniques such as single‐molecule fluorescence resonance energy transfer, circular dichroism with deconvolution analysis, site‐directed mutagenesis, trypsin digestion assays, and all‐atom molecular dynamics simulations in conjunction with enhanced sampling techniques, we show that Alb3‐Cterm contains transient secondary structure in motifs I and II. The excellent agreement between the experimental and computational data provides a quantitatively consistent picture and allows us to identify a heterogeneous structural ensemble that highlights the local and transient nature of the secondary structure. This structural ensemble was used to predict both the inter‐residue distance distributions of single molecules and the apparent unfolding free energy of the transient secondary structure, which were both in excellent agreement with those determined experimentally. We hypothesize that this transient local secondary structure may play an important role in the recognition of Alb3‐Cterm for the LHC‐loaded transit complex, and these results should provide a framework to better understand protein targeting by the Alb3‐Oxa1‐YidC family of insertases.

Okoto, Patience S.↗
DOE OSTI2021

Chemical vapor infiltration of additively manufactured preforms: Pore-resolved simulations and experimental validation

The densification of additively manufactured porous preforms by chemical vapor infiltration (CVI) is studied using pore-resolved simulations and experiments. Experimentally, 3D printed silicon carbide (SiC) preforms are subject to CVI synthesis using methyltrichlorosilane (MTS) precursor to obtain high purity SiC/SiC composites. Optical images of the cross sections of the processed preforms are analyzed to obtain the spatial porosity distribution. The numerical method is based on a level set formulation to capture the spatial distribution and time evolution of the pore scale microstructural characteristics. The coupled transport and kinetic effects are represented using a dimensionless Thiele modulus. Simulations are initialized using representative synthetic preform geometries comprising of packed particles based on the size distribution of the powder used for 3D printing. The simulation results are validated against the experimental observations in terms of total density and the distribution of residual porosity. The densification characteristics, porosity classification, concentration profiles, and structure functions are analyzed as functions of processing temperature and Thiele modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Overview of recent SCALE activities for Non-LWR inventory and decay heat analysis

In 2019, the US Nuclear Regulatory Commission initiated a project for the development and assessments of non-light-water reactor (non-LWR) accident progression using the SCALE and MELCOR simulation tools. SCALE simulations are used to generate nuclide inventories, full-core power distributions, decay heat, and kinetics parameters to initialize MELCOR simulations of severe accident scenarios. Five non-LWR concepts were studied: high-temperature gas-cooled reactor (HTGR), heat pipe reactor (HPR), high-temperature fluoride salt-cooled reactor (FHR), molten salt-fueled reactor (MSR), and sodium-cooled fast reactor (SFR). This paper summarizes the SCALE results obtained in 2021 for the first three non-LWR concepts, compares characteristics and results to common LWRs, and provides the strategy for the analysis of the remaining two non-LWRs. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Water-Oil Displacement in Shale: New Insights from a Comparative Study Integrating Imbibition Tests and Multiscale Imaging

Water-oil displacement is an important process that occurs in a shale matrix after hydraulic fracturing and in water-based enhanced oil recovery. Current understanding of this displacement process is limited because of the complicated pore structure and surface properties in shale. In this work, this process and its controlling factors are investigated through a comparative study of three shale samples that have different types of pore systems and wettability. Here, an integrated method of imbibition and multiscale imaging was applied, and a modified oleic tracer that can better represent oil flow was used in imbibition testing and micro-computed tomography (CT) imaging. Scanning electron microscope (SEM) pore characterization was then performed under high magnification with guidance from the micro-CT images showing the changes caused by oil or water imbibition. New insights were obtained on the importance of both wettability and pore size effect on oil recovery and the distribution of residual oil after water-oil displacement. Connectivity of pores with different wettability is also discussed based on 3D analysis and SEM pore characterization. Collectively, these new findings improve the understanding of the complicated process of water-oil displacement and the role of influencing factors. Important implications for improved oil recovery strategy in shale are discussed for different types of reservoir rocks. The integrated imaging and imbibition technique provides a new path for further investigation of improved oil recovery in shale.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Influence of Process Parameters and Alloy Composition on Crack Mitigation in Selective Laser Melting

Microcracking and residual stresses are key limitations of laser powder bed fusion (LPBF), an additive manufacturing (AM) technique that uses a high power laser to consolidate successive layers of metal powder. For tungsten, these microcracks find their origin in the combination of a ductile-to-brittle transition (DBT) between 200°C and 400°C and high residual stresses. This work utilized in situ high speed video to capture the cracking mechanisms, and combined the experimental results with thermomechanical modeling to unveil correlations between crack network morphology and process parameter-related variables, such as the local temperature and residual stress distributions. Consequently, preheating and alloying with rare earth oxides were adopted as possible crack mitigation strategies, the efficacy of which was tested against the initial fundamental baseline results. Preheating temperatures above 500°C eliminated all cracking, though this threshold is expected to be higher when tungsten powder (higher oxygen content) is introduced. Alloying can serve as an active oxygen getter in the system, but the rare earth oxides in this work were too large to have significant contributions to crack-mitigation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fabricating Single Crystal Quantum Dot Solids

The central goal of this research program was to establish fundamental synthesis and processing principles to enable the fabrication of single crystal quantum dot solids (QDS) with programmable structure (i.e., hexagonal and square) and composition. Our approach towards that goal leveraged access to and experience with unique in-situ, multi-probe characterization techniques to understand and ultimately control the fundamental relationship between processing conditions and nucleation and growth of QDS. The program integrated synthesis and fabrication (Hanrath) with in-situ TEM analysis (Kourkoutis) and computational modeling (Clancy) to gain atomic-level insights into the underlying physical phenomena governing assembly and attachment and to guide the development of optimized processing methods. We have established a foundational understanding of physicochemical interactions of self-assembly at a fluid interface, superlattice structure transformation pathways, the critical role of disorder during the initial dimerization of colloidal quantum dot monomers, and the residual strain distribution within the inter-dot epitaxial bridge which hampers the formation of novel electronics states of the quantum dot solids. Collectively, these insights have contributed towards advancing the mechanistic understanding of the complex choreography of assembly and attachment as well as understanding what currently limits further advances in high-fidelity quantum dot solids and tiles.

36 MATERIALS SCIENCE↗