Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Residual Stresses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Residual Stress Measurements of Cr-coated Cladding

Accident-tolerant fuel concepts for light-water reactor applications have been developed and tested in diverse research programs around the world. Industry teams have developed coated cladding concepts using different coating application methods, such as physical vapor deposition and coldspraying. Recently, variations in thickness and application method were investigated, and their effects on the microstructure and mechanical properties were reported. The results suggest an increase in performance in an unirradiated state, however, it remains unclear what phenomenon drove this performance. One explanation to this performance is associated with the coating process imparting a residual stress. Residual stress analysis was performed on coatings produced with various process parameters to understand how a thin layer of Cr impacts the mechanical properties after coating application and after simulated operating conditions. The gathered information is intended to address safety concerns or support margin identification related to accident-tolerant fuels and to support subsequent modeling and simulation efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1976

Residual stresses in polymer matrix composite laminates

Residual stresses in composites are induced during fabrication and by environmental exposure. The theory formulated can describe the shrinkage commonly observed after a thermal expansion test. Comparison between the analysis and experimental data for laminates of various material systems indicates that the residual stress-free temperature can be lower than the curing temperature, depending on the curing process. Effects of residual stresses on ply failure including the acoustic emission characteristics are discussed.

Hahn, H. T.↗
NASA NTRS1984

The Effect of Creep on the Residual Stresses Generated During Silicon Sheet Growth

The modeling of stresses generated during the growth of thin silicon sheets at high speeds is an important part of the EFG technique since the experimental measurement of the stresses is difficult and prohibitive. The residual stresses which arise in such a growth process lead to serious problems which make thin Si ribbons unsuitable for fabrication. The constitutive behavior is unrealistic because at high temperature (close to the melting point) Si exhibits considerable creep which significantly relaxes the residual stresses. The effect of creep on the residual stresses generated during the growth of Si sheets at high speeds was addressed and the basic qualitative effect of creep are reported.

Hutchinson, J. W.↗
DOE OSTI2024

Effects of Aluminum Plate Initial Residual Stress on Machined-Part Distortion

Dimensional tolerances for high-speed-machined aluminum products continue to tighten due to the demand for automated assembly of complex monolithic parts in aerospace and other industries. Understanding the contribution of inherent residual stress in wrought Al 7050-T7451 plate, common in aircraft manufacture, to distortion of high-aspect-ratio machined parts is critical but remains problematic due to the alloy's low residual stress magnitude over large geometries. Prior investigations into residual stress effects on machined part distortion suffer inadequate characterizations of the wrought material stress field, either because of low fidelity due to “slitting” methods, confounding effects in machined-layer removal methods, or small sample size when using neutron diffraction (ND). In this work, inherent residual stress is measured via ND at 860 locations in a 90.5 mm thick Al 7050-T7451 plate having dimensions 399 mm in the rolling direction and 335 mm in the transverse direction. Unlike prior studies, the ND residual stress is reconstructed using an iterative algorithm to ensure fully compatible, equilibrated 3D field prior to examining its effect on distortion. Further, the findings from simulations and experiments show that inherent residual stress alone could distort a high-aspect-ratio part beyond aerospace industry requirements, that slitting measurements may not sufficiently characterize residual stress for predicted distortion, and that parts machined from different plate thickness locations could exhibit reversed distortion patterns. Thus, research into distortion prediction that considers machining should carefully characterize and reconstruct inherent residual stress so that the coupled machining effects are accurately modeled.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simultaneous optimization of hatching orientations and lattice density distribution for residual warpage reduction in laser powder bed fusion considering layerwise residual stress stacking

The reduction in the residual warpage generated via fabrication is an emerging issue in metals’ laser powder bed fusion additive manufacturing (AM). One solution from a design for additive manufacturing (DfAM) perspective is to arrange a hatching strategy that utilizes the asymmetry of the residual stress generated from a molten pool. Another approach is to arrange the geometry of the parts, such as forming an inner lattice structure to arrange the effective stiffness. In this study, the simultaneous optimization of the laser hatching orientation and lattice density distribution was conducted to minimize the residual warpage in lattice infill structures and confirm their synergetic effect. The mutual effect of each layer was highlighted when considering the mechanical background of the optimal results because an imbalance in the residual stress caused the warpage of the AM parts between the layers. The proposed methodology was validated via experimental verification using a quasi-2D plate, 3D bracket, and 3D connecting-rod design problems. The residual warpage in the quasi-2D study, measured as the edge’s vertical deformation, was reduced from 23.4% to 39.4% compared with the benchmark design. In the 3D studies, the warpage reductions ranged from 13.1% to 20.7%.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Patterns of residual stresses due to welding

Residual stresses caused by welding result from the nonuniform rate of cooling and the restrained thermal contraction or non-uniform plastic deformation. From the zone of extremely high temperature at the weld, heat flows into both the adjoining cool body and the surrounding atmosphere. The weld metal solidifies under very rapid cooling. The plasticity of the hot metal allows adjustment initially, but as the structure cools the rigidity of the surrounding cold metal inhibits further contraction. The zone is compressed and the weld is put under tensile stresses of high magnitude. The danger of cracking in these structural elements is great. Change in specific volume is caused by the change in temperature.

Botros, B. M.↗
NASA NTRS1985

Finite element analysis of residual stress in plasma-sprayed ceramic

Residual stress in a ZrO2-Y2O3 ceramic coating resulting from the plasma spraying operation is calculated. The calculations were done using the finite element method. Both thermal and mechanical analysis were performed. The resulting residual stress field was compared to the measurements obtained by Hendricks and McDonald. Reasonable agreement between the predicted and measured moment occurred. However, the resulting stress field is not in pure bending.

Mullen, R. L.↗
NASA NTRS2015

Characterization of Residual Stress Effects on Fatigue Crack Growth of a Friction Stir Welded Aluminum Alloy

An on-line compliance-based method to account for residual stress effects in stress-intensity factor and fatigue crack growth property determinations has been evaluated. Residual stress intensity factor results determined from specimens containing friction stir weld induced residual stresses are presented, and the on-line method results were found to be in excellent agreement with residual stress-intensity factor data obtained using the cut compliance method. Variable stress-intensity factor tests were designed to demonstrate that a simple superposition model, summing the applied stress-intensity factor with the residual stress-intensity factor, can be used to determine the total crack-tip stress-intensity factor. Finite element, VCCT (virtual crack closure technique), and J-integral analysis methods have been used to characterize weld-induced residual stress using thermal expansion/contraction in the form of an equivalent delta T (change in local temperature during welding) to simulate the welding process. This equivalent delta T was established and applied to analyze different specimen configurations to predict residual stress distributions and associated residual stress-intensity factor values. The predictions were found to agree well with experimental results obtained using the crack- and cut-compliance methods.

Newman, John A.↗
NASA NTRS1976

Longitudinal residual stresses in boron fibers

A method of measuring the longitudinal residual stress distribution in boron fibers is presented. The residual stresses in commercial CVD boron on tungsten fibers of 102, 142, and 203 microns (4, 5.6, and 8 mil) diameters were determined. Results for the three sizes show a compressive stress at the surface 800 to -1400 MN/sq m 120 to -200 ksi), changing monotonically to a region of tensile stress within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile 600 to 1000 MN/sq m(90 to 150 ksi) and then decreases to compressive near the tungsten boride core. The core itself is under a compressive stress of approximately -1300 MN/sq m (-190 ksi). The effects of surface removal on core residual stress and core-initiated fracture are discussed.

Behrendt, D. R.↗
NASA NTRS1992

The effects of uneven fiber spacing on thermal residual stresses in a unidirectional SCS-6/Ti-15-3 laminate

High residual stresses develop in SCS-6/Ti-15-3 composites during cooldown from the fabrication temperature; these residual stresses can effect the mechanical and physical properties of the composite. Discrete fiber-matrix finite element models were used to study the residual stresses due to the temperature change during the fabrication process, including the effects of uneven fiber spacing, the free surface, and increased fiber volume fractions. To accurately model the effects of the free surface, it is only necessary to model one fiber through the thickness. Below the first ply, the analysis predicts stress distributions that are identical to the infinite array predictions. For uneven fiber space less than 0.042 mm in an interior ply, the maximum hoop stress was predicted to occur between fibers within a ply and to increase as the fiber spacing decreased. The maximum hoop stress correlated well with the observed radial cracking between fibers. For the case of touching fibers, the analysis predicted tensile radial stresses at the fiber-matrix debonding during the fabrication cooldown. Identical trends were predicted for uneven fiber spacing in surface plies with slightly greater values of maximum stresses. The analysis predicted matrix yielding to occur upon cooldown when the edge-to-edge fiber spacing was less than or equal to 0.022 mm. The stress distributions preidcted for increasing fiber volume fractions were similar to those predicted for decreasing the fiber spacing for two adjacent fibers within a ply.

Bigelow, Catherine A.↗
DOE OSTI2023

Impact of Plate Thickness and Joint Geometry on Residual Stresses in 347H Stainless Steel Welds

Weldments of 347H stainless steel are potentially susceptible to stress relaxation cracking at elevated service temperatures. Mitigation of stress relaxation cracking susceptibility within a multipass weld requires a good understanding of welding practices and manufacturing techniques to control high tensile residual stresses. Here in this work, the dependence of residual stress distribution in 347H stainless steel on base plate thickness, joint geometry design, and preheating condition was systematically investigated by using three-dimensional finite element models. The finite element models were validated through good agreement between neutron diffraction measurements and calculated elastic strains. The single-V-groove welds with and without a preheating step all produced similar peak von Mises residual stresses, above 450 MPa, within both the fusion zone and heat-affected zone (HAZ). In plates thicker than 0.5 in. (12.7 mm), high tensile residual stress could be observed in a relatively large area, from the middle of the plate thickness to underneath the top surface. A double-V groove shifted the high tensile stress area to the middle thickness of the weld. A single-J-groove weld was able to confine the residual stress to a very small region near the middle thickness within the fusion zone and suppressed the von Mises residual stress within the HAZ to below 400 MPa.

14 SOLAR ENERGY↗
DOE OSTI2021

Residual stress analysis of aluminum nitride piezoelectric micromachined ultrasonic transducers using Raman spectroscopy

In this study, the Raman biaxial stress coefficients K II and strain-free phonon frequencies ω 0 have been determined for the E 2 (low), E 2 (high), and A 1 (LO) phonon modes of aluminum nitride, AlN, using both experimental and theoretical approaches. The E 2 (high) mode of AlN is recommended for the residual stress analysis of AlN due to its high sensitivity and the largest signal-to-noise ratio among the studied modes. The E 2 (high) Raman biaxial stress coefficient of ₋3.8 cm₋1/GPa and strain-free phonon frequency of 656.68 cm ₋1 were then applied to perform both macroscopic and microscopic stress mappings. For macroscopic stress evaluation, the spatial variation of residual stress was measured across an AlN-on-Si wafer prepared by sputter deposition. A cross-wafer variation in residual stress of ~150 MPa was observed regardless of the average stress state of the film. Microscopic stress evaluation was performed on AlN piezoelectric micromachined ultrasonic transducers (pMUTs) with submicrometer spatial resolution. These measurements were used to assess the effect of device fabrication on residual stress distribution in an individual pMUT and the effect of residual stress on the resonance frequency. At ~20 μm directly outside the outer edge of the pMUT electrode, a large lateral spatial variation in residual stress of ~100 MPa was measured, highlighting the impact of metallization structures on residual stress in the AlN film.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Longitudinal residual stresses in boron fibers

A technique is proposed for measuring the longitudinal residual stress distribution in commercial CVD (Chemical Vapor Deposition) boron on tungsten fibers of 102, 142, and 203 microns in diameter. The experimental apparatus is so designed that continuous measurements are made of the length changes of a boron fiber specimen as the surface of the fiber is removed by electropolishing. The effects of surface removal on core residual stress and core-initiated fracture are discussed. The three sizes of boron fibers investigated show similar residual stress distributions, i.e., compressive at the surface, tensile near the core, and for the 102-micron fiber compressive again in the core. It is shown that an increase in UTS is due to the increase in the compressive stress at the core produced by fiber contraction during surface removal. An expression is derived for calculating the longitudinal residual stress at a given radius for an as-received fiber of a certain radius from measurements of the axial strain produced by removal of the surface by electropolishing.

Behrendt, D. R.↗
DOE OSTI2021

Residual stresses and microstructure within Allvac 718Plus laser powder bed fusion bars

The residual stresses within Allvac 718Plus bars built using LBPF with different laser powers, speeds and table displacements were measured using diffraction and mechanical methods and modelled with the baseplate attached and then removed. The residual stress profiles within the bars from the top surface down through the bulk were all quite similar, becoming less tensile due to a strain hardening mechanism. Table displacement has the greatest impact on residual stress, decreasing with increasing displacement/powder layer thickness. There was good agreement amongst the modeling and measurements. The microstructures were examined and varied slightly with energy density with higher densities having larger grains and enhanced post solidification diffusion. We found energy density had minimal impact on the residuals stresses within the parameters to produce dense material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Control of machining-induced residual stress via tool geometry and process parameter modification

Distortion generated in machined, monolithic, thin-walled aerospace components due to residual stresses leads to significant material and economic waste in the manufacturing industry. Inherent residual stress (IRS) present in stock materials combines with machining-induced residual stress (MIRS) to influence the final machined part distortion. It is hypothesized that MIRS can be controlled, based on the part geometry, through deliberate cutting tool geometry and process parameter modifications to negate the effect of IRS on distortion, consequently resulting in distortion-free parts. A finite element (FE) orthogonal cutting model is developed to study how tool geometry and process parameters influence machining-induced residual stress (MIRS). Orthogonal cutting experiments are performed on Al 7075-T651 samples to measure cutting forces and MIRS. A cutting force dynamometer is used to measure forces during cutting and a novel digital image correlation (DIC) based hole drilling technique is employed to measure the near-surface residual stress (RS) in the cut samples. These data are subsequently utilized to validate the FE prediction model. Various cases of cutting simulations involving different depths of cut, tool tip radii, and rake angles are performed to study their effects on RS. Similar to prior literature, increasing the depth of cut, tool tip radius, or rake angle is found to promote the formation of near-surface tensile stresses. The competing effects of material plowing and temperature are shown to determine the type of RS at the end of the cut. Moreover, a window of variation of RS (up to ± 400 MPa) is estimated within the given range of conditions, allowing for the control of MIRS through tool and process modification.

Mathews, Ritin [ORNL] (ORCID:0000000301440828)↗
DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Crystal plasticity model of residual stress in additive manufacturing using the element elimination and reactivation method

Selective laser melting is receiving increasing interest as an additive manufacturing technique. Residual stresses induced by the large temperature gradients and inhomogeneous cooling process can favour the generation of cracks. In this work, a crystal plasticity finite element model is developed to simulate the formation of residual stresses and to understand the correlation between plastic deformation, grain orientation and residual stresses in the additive manufacturing process. The temperature profile and grain structure from thermal-fluid flow and grain growth simulations are implemented into the crystal plasticity model. An element elimination and reactivation method is proposed to model the melting and solidification and to reinitialize state variables, such as the plastic deformation, in the reactivated elements. The accuracy of this method is judged against previous method based on the stiffness degradation of liquid regions by comparing the plastic deformation as a function of time induced by thermal stresses. The method is used to investigate residual stresses parallel and perpendicular to the laser scan direction, and the correlation with the maximum Schmid factor of the grains along those directions. The magnitude of the residual stress can be predicted as a function of the depth, grain orientation and position with respect to the molten pool. The simulation results are directly comparable to X-ray diffraction experiments and stress–strain curves.

316 stainless steel↗
DOE OSTI2021

A Comparative Study of Layer Heating and Continuous Heating Methods on Prediction Accuracy of Residual Stresses in Selective Laser Melted Tube Samples

Thermal distortion and residual stresses are two important factors that affect the quality and reliability of steel parts manufactured by laser powder bed fusion (LPBF) processes. A cost-effective model for evaluation of those heat effects is needed to refine the manufacturing process and provides insights into the product design and heat treatment. In this study, the layer heating method and sophisticated track-layer scanning method were applied to simulate the thermo-mechanical response of IN625 tube parts built by LPBF. Based on the similarity of temperature field in each layer deposit, a swept mesh was constructed to perform the thermal analysis for top layer, with the rest of layers referring to the temperature by node number offsetting. A novel explicit finite element analysis code accelerated by graphics processing unit was used for the massive-element numerical analysis. The computational accuracy and efficiency of the layer heating and track-layer scanning methods were compared in detail. It is shown that layer heating method can efficiently capture the pattern of stress distribution with reasonable accuracy in stress magnitude. The grouped track-layer scanning method can predict the residual stress and strain more accurately at a higher cost (5 ~ 10×). The elastic strain distribution was compared with the measurement by X-ray diffraction, confirming the accuracy of residual stress prediction.

36 MATERIALS SCIENCE↗