Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Refractories”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Reaction Behaviors of Al-Killed Medium-Manganese Steel with Glazed MgO Refractory

In order to understand the reaction mechanism of Al-killed medium-Mn steel with glazed MgO refractory, some laboratory experiments were conducted at [1873 K (1600 °C)]. The refractory rods were glazed by four different basicity slags, and inserted into liquid steel (Mn:5.5 mass pct) for different times. The results show that MgO refractory can react with medium-Mn steel to generate (Mn, Mg)O solid solution with even (Mn, Mg)O-Al{sub 2}O{sub 3} spinel at the boundary of the refractory. When a glaze layer is formed at the edge of a MgO refractory, the glaze layer will supply inclusions into liquid steel and may act as a protection layer for the refractory. Although the glaze could also react with dissolved Mn in steel to generate MnO in both the glaze and refractory, the MnO contents in both the glaze and refractory are evidently lower than that without glaze. The reaction between glazed MgO refractory and liquid steel is influenced by the basicity of the glaze layer. High-basicity slag would hinder the generation of MnO in both the glaze and refractory. Therefore, lower-basicity glaze needs to be avoided for the steelmaking process of medium-Mn steel grades.

36 MATERIALS SCIENCE↗
DOE OSTI2011

NOvel Refractory Materials for High Alkali, High Temperature Environments

Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, highalkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. A research team was formed to carry out the proposed work led by Oak Ridge National Laboratory (ORNL) and was comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The two goals of this project were to produce novel refractory compositions which will allow for improved energy efficiency and to develop new refractory application techniques which would improve the speed of installation. Also methods of hot installation were sought which would allow for hot repairs and on-line maintenance leading to reduced process downtimes and eliminating the need to cool and reheat process vessels.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2018

Reaction Behaviors of Al-Killed Medium-Manganese Steel with Different Refractories

In order to understand the reaction mechanism between medium-manganese steel and different refractories, some laboratory experiments were carried out at 1873 K (1600 °C). Three types of refractory plates (Al{sub 2}O{sub 3}, MgO, and MgO·Al{sub 2}O{sub 3}) were used. The results show that Mn in liquid medium-manganese steel does not react easily with the Al{sub 2}O{sub 3} refractory, but can react with the MgO refractory to generate a (Mn, Mg)O layer at the boundary between the refractory plate and liquid steel. After the formation of (Mn, Mg)O, a layer of (Mn, Mg)O·Al{sub 2}O{sub 3} spinel is also formed at the edge of the MgO refractory. Similar to the MgO refractory, the dissolved Mn can react with the MgO·Al{sub 2}O{sub 3} refractory as well, and a layer of (Mn, Mg)O·Al{sub 2}O{sub 3} was also detected after reaction. It was found that the formation of (Mn, Mg)O·Al{sub 2}O{sub 3} at the edge of the refractory is a source of (Mn, Mg)O·Al{sub 2}O{sub 3} inclusions in liquid steel. The flush-off of the (Mn, Mg)O·Al{sub 2}O{sub 3} layer would result in the formation of (Mn, Mg)O·Al{sub 2}O{sub 3} inclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al{sub 2}O{sub 3}-TiN and MgAl{sub 2}O{sub 4}-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl{sub 2}O{sub 4}-TiN interface rather than that of Al{sub 2}O{sub 3}-TiN interface. When ∆T{sub TiN} (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Glass-contact refractory of the nuclear waste vitrification melters in the United States: a review of corrosion data and melter life

The performance of the refractory lining in glass melters used for nuclear waste vitrification is critical to the melter reliability for long-term continuous operation. Monofrax® K-3, a high Cr 2 O 3 fused cast refractory material, has been widely used to build the liners of nuclear waste glass melters in the United States. Corrosion behaviour of Monofrax® K-3 refractory has been evaluated based on crucible-scale testing, inspection of the refractory components following scaled melter testing, and inspections of the Defense Waste Processing Facility (DWPF) melter refractory after service. The literature generally consists of empirical models based on short-term testing to describe refractory corrosion dependence on glass composition. Corrosion data from tests with longer testing times, at various temperatures, in the presence of molten salts, and with different redox reactions in the plenum atmosphere exist, may be insufficient to provide accurate refractory service life estimates. Additionally, the corrosion data collected under actual and scaled melter operating conditions are limited. Recommendations to achieve more direct correlation between the laboratory refractory corrosion data predictions and the observed melter service life are discussed to allow for more accurate predictions of the useful life of melter refractory linings.

Jin, Tongan↗
DOE OSTI2022

Microstructural examination of interactions between chromia-based refractory and nuclear glass in a melter

This study shows the effects of nuclear waste glass production on Monofrax K-3 refractory corrosion. A continuously fed research-scale melter containing an Fe- and Ni-rich simulated nuclear waste feed with borosilicate glass-forming chemicals was cyclically melted at 1150°C and idled at 1050°C for a total of 11 weeks. Chemical maps using scanning electron microscopy show the interactions between the quenched melt and the refractory. Nanoscale X-ray-computed tomography was used for a three-dimensional visualization of certain parts of the interface. Unreacted K-3 consists of primarily corundum (Al,Cr) 2 O 3 and spinel (Fe 2+ ,Mg)(Al,Cr) 2 O 4 interlocking crystalline phases. Some of the Cr from the refractory interacts with the Ni and Fe from the melt to form a reaction layer comprising (Ni,Fe 2+ )(Cr,Fe 3+ ) 2 O 4 spinel crystals. Simultaneously, melt components (Na,Si) infiltrate into the refractory. This interaction proceeds at the expense of the integrity of the refractory structure. Intact refractory grains (e.g., (Al,Cr) 2 O 3 ) as well as the reaction layer itself can lose mechanical integrity and spall off into the melt, especially near the top of the melter. As the reaction layer can be a protective boundary for the refractory against further melt infiltration, a reduction in the reaction layer thickness allows an increase in refractory corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Corrosion behavior of Monofrax K-3 refractory in borosilicate-based model low activity waste glass melts

Owing to its good chemical and thermal durabilities at high temperatures, Monofrax K-3 refractory is widely used in nuclear waste vitrification as a lining material in melting vessels. However, the corrosion of K-3 refractory during the vitrification of nuclear waste is a serious problem because it affects the melter's safety, performance, and lifetime. Therefore, in the present study, we have focused on unearthing the impact of glass network formers, such as SiO 2 , B 2 O 3 , and Al 2 O 3 , in a model nuclear waste glass composition on the corrosion of Monofrax K-3 refractory. The corrosion tests have been performed per ASTM C621 at 1150°C for 5 days. The dimensional measurements on corroded K-3 refractory suggest that Al 2 O 3 and SiO 2 tend to reduce the refractory corrosion (neck loss), with the effect of Al 2 O 3 being significant. A corroded region on the K-3 refractory at the melt–refractory interface is observed. The corrosion occurs via a coupling of the melt infiltration induced by a capillary effect and the dissolution of Al, Mg, and Fe components from K-3 into the melt through chemical reactions. A Cr-rich layer is retained on the glass contact surface of the corroded K-3 refractory.

36 MATERIALS SCIENCE↗
DOE OSTI2018

AOI [3]: Smart Refractory Sensor Systems for Wireless Monitoring of Temperature, Health, and Degradation of Slagging Gasifiers

The objective of the work was to develop refractory “smart bricks”, which would contain embedded temperature, strain/stress, and spallation sensors throughout the volume of highchromia (-Cr 2 O 3 ) refractory brick. The proposed work included work to interconnect the sensors to the reactor exterior, where the sensor signals may be processed by low-power electronics and transmitted wirelessly to a central processing hub. The data processing and wireless transmitter hardware was specifically designed to be isolated (with low power consumption) and to be adaptable to future implementation of energy-harvesting strategies for extended life. Finally, the collected data was incorporated into a model to estimate refractory degradation, a technique that could help monitor the health of the refractory in real-time. The long-term goal of this program was to demonstrate high-temperature, wireless sensor arrays for in situ three-dimensional (3-D) refractory monitoring or mapping for slagging gasification systems. The research was in collaboration with HarbisonWalker International (HWI) Technology Center in West Mifflin, PA. HWI is a leading developer and manufacturer of ceramic refractory products for high-temperature applications. The work completed focused on the following areas: 1) Investigation of the chemical stability, microstructural evolution, grain growth kinetics, degree of homogeneity (quantitative image analysis), and electrical properties of refractory oxide-silicide composites at temperatures between 750-1450ºC; 2) Fabrication of silicide-alumina composite and oxide thermocouples and thermistor preforms and the development of techniques to embed them into high-chromia refractory bricks to form “smart bricks”; 3) Utilization of commercial off-the-shelf discrete components to prototype circuits for interfacing between smart brick sensors and the wireless sensor network. The prototypes were then used to design an integrated circuit for thermistor, thermocouple, and capacitive-based smart brick sensor interfacing; 4) Interfacing of the smart bricks with embedded sensors with wireless motes thus yielding a complete signal chain. This end-to-end data collection system was tested on a furnace heated to 1350°C; 5) Development of a slag penetration model and a nonlinear unknown input filter for the data from the embedded sensors for estimating temperature and extent of slag penetration.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2013

Refractory Materials based on Magnesia-Alumina Spinel for Improved Performance in Coal Gasification Environments

As part of a larger project to develop novel refractory systems and techniques to reduce energy consumption of refractory lined vessels, a team composed of Oak Ridge National Laboratory, refractory manufacturer Minteq International, Inc., and academic partner Missouri University of Science and Technology have developed new refractory materials and coating systems specifically for application in coal gasification environments. Materials were developed under this U.S. DOE funded project to address the need for innovative refractory compositions by developing MgO-Al2O3 spinel gunnable refractory compositions utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques. Work was conducted to develop and deploy these new materials and to develop and apply low cost coatings using a colloidal approach for protection against attack of the refractory brick by the serviced environment. Additionally, a light-weight back-up refractory system was developed to help offset the high thermal conductivity inherent in spinel materials. This paper discusses the efforts involved in the development of these materials, along with the laboratory testing and evaluation of these materials leading to relevant results achieved toward the reduction of chemical reactions and mechanical degradation by the service environment though compositional and processing modifications.

Hemrick, James Gordon↗
DOE OSTI2013

SPINEL-BASED REFRACTORIES FOR IMPROVED PERFORMANCE IN COAL GASIFICATION ENVIRONMENTS

Oak Ridge National Laboratory, in collaboration with refractory manufacturer Minteq International, Inc., academic partner Missouri University of Science and Technology and refractory end users have developed novel refractory systems and techniques to reduce energy consumption of refractory lined vessels. The objective of this U.S. DOE funded project was to address the need for innovative refractory compositions by developing MgO-Al 2O3 spinel gunnable refractory compositions utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques. Materials have been developed specifically for coal gasification environments and work has been performed to develop and apply low cost coatings using a colloidal approach for protection against attack of the refractory brick by the service environment and to develop a light-weight back-up refractory system to help offset the high thermal conductivity inherent in spinel materials. This paper discusses the systematic development of these materials, laboratory testing and evaluation of these materials, and relevant results achieved toward the reduction of chemical reactions and mechanical degradation by the service environment though compositional and processing modifications.

Hemrick, James Gordon↗
DOE OSTI2014

Design of Refractory Linings for Balanced Energy Efficiency, Uptime, and Capacity in Lime Kilns

The rotary kilns used by the pulp and paper industry to regenerate lime in the Kraft process are very energy intensive. Throughout the 90 s, in response to increasing fuel prices, the industry used back up insulation in conjunction with the high alumina brick used to line the burning zones of their kilns. While this improved energy efficiency, the practice of installing insulating brick behind the working lining increased the inner wall temperatures. In the worst case, due to the increased temperatures, rapid brick failures occurred causing unscheduled outages and expensive repairs. Despite these issues, for the most part, the industry continued to use insulating refractory linings in that the energy savings were large enough to offset any increase in the cost of maintaining the refractory lining. Due to the dramatic decline in the price of natural gas in some areas combined with mounting pressures to increasing production of existing assets, over the last decade, many mills are focusing more on increasing the uptime of their kilns as opposed to energy savings. To this end, a growing number of mills are using basic (magnesia based) brick instead of high alumina brick to line the burning zone of the kiln since the lime mud does not react with these bricks at the operating temperatures of the burning zone of the kiln. In the extreme case, a few mills have chosen to install basic brick in the front end of the kiln running a length equivalent to 10 diameters. While the use of basic brick can increase the uptime of the kiln and reduce the cost to maintain the refractory lining, it does dramatically increase the heat losses resulting from the increased operating temperatures of the shell. Also, over long periods of time operating at these high temperatures, damage can occur in the shell. There are tradeoffs between energy efficiency, capacity and uptime. When fuel prices are very high, it makes sense to insulate the lining. When fuel prices are lower, trading some thermal efficiency for increased uptime and capacity seems reasonable. This paper considers a number of refractory linings in an effort to develop optimized operating strategies that balance these factors. In addition to considering a range of refractory materials, the paper examines other factors such as the chain area, discharge dams and other operating variables that impact the service life of the refractory lining. The paper provides recommendations that will help mill personnel develop a strategy to select a refractory lining that is optimized for their specific situation.

Computational Modeling↗
DOE OSTI2013

DEVELOPMENT AND APPLICATION OF IMPROVED SHOTCTRETE REFRACTORY FOR ALUMINUM ROTARY FURNACE APPLICATIONS

Oak Ridge National Laboratory, in collaboration with refractory manufacturer Minteq International, Inc., academic partner Missouri University of Science and Technology and refractory end users have developed novel refractory systems and techniques to reduce energy consumption of refractory lined vessels. The objective of this U.S. DOE funded project was to address the need for innovative refractory compositions by developing novel gunnable refractory compositions for use in high temperature and high alkali environments. Developed materials utilized new aggregate materials, bond systems, protective coatings, and phase formation techniques. Under this project, materials were developed specifically for aluminum rotary dross furnace applications and a light-weight back-up refractory system was also developed to improve the thermal efficiency of the installed lining system. This paper discusses the systematic development of these materials, laboratory testing and evaluation of these materials, and the performance of several industrial trials performed using these newly developed materials. The success of the industrial trials will be highlighted and future areas of application of these materials discussed.

Hemrick, James Gordon↗
DOE OSTI2017

Chromia refractory brick with carbon treatment

The disclosure provides a refractory brick system comprising a chromia refractory brick for operation in the slagging environment of an air-cooled gasifier. The chromia refractory brick comprises a ceramically-bonded porous chromia refractory having a porosity greater than 9% and having carbon deposits residing within the pores. The brick may be further comprised of Al.sub.2O.sub.3. The air-cooled gasifier generates a liquefied slag in contact with the refractory brick and generally operates at temperatures between 1250.degree. C. and 1575.degree. C. and pressures between 300 psi to 1000 psi, with oxygen partial pressures generally between 10.sup.-4 and 10.sup.-10 atm. The refractory brick performs without substantial chromium carbide or chromium metal formation in the low oxygen partial pressure environment. The inclusion of carbon without chromium carbide formation provides for significant mitigation of slag penetration and significantly reduced refractory wear.

36 MATERIALS SCIENCE↗
DOE OSTI2025

CFD modeling and simulation for corrosive wear of refractory in molten slag

The development of high-wear resistant refractories having minimal production costs is facilitated by characterizing the wear mechanisms associated with their corrosive wear. Static cup testing is a commonly used method for comparing the corrosion resistance performance of two or more refractory materials. Although the static cup test conditions are not as severe as dynamic tests, this study shows that the thermal gradient present within the system during heating and cooling stages serves to generate movement of the slag leading to mechanical wear. The thermal gradient within the refractory, and between the slag and the refractory, occurs during the ramp stage of the test and lasts until the soaking stage is reached bringing the system to a thermal equilibrium. Using computational fluid dynamics (CFD) capabilities embedded within ANSYS software, this study modelled and quantified the convection currents within the slag and associated shear stresses generated on the refractory walls due to the thermal gradient. A traditional ladle furnace was employed as a case study to verify the results of the studied CFD model. The corrosion rate of the refractory lining was found to depend on the mass transfer coefficient of the refractory dissolution into the slag, and a velocity term which governs the extent of corrosion at any given location. This velocity term is a function of slag viscosity, as well as the concentration gradient and/or temperature gradient at the triple points. In this study, wall shear stress was used as a reliable proxy for identifying high-velocity regions prone to excessive corrosive wear. Elevated wall shear stress near the slag/air and slag/molten steel interfaces align with observed corrosion grooves, which reflects the intensified corrosive wear at these locations.

Ramteke, Rajat Rajat Durgesh Ramteke [University o↗
DOE OSTI2022

Zinc aluminate (ZnAl 2 O 4 ) refractory aggregates: Dilatometric sintering studies and thermal expansion coefficient

ZnAl 2 O 4 has recently been reported to enhance thermomechanical properties and slag corrosion resistance of refractory castables. The pore generation and deleterious expansion during in situ ZnAl 2 O 4 formation can limit their amount in a refractory composition. A comprehensive dilatometric study is presented, identifying the optimum raw materials and processing conditions. Preformed ZnAl 2 O 4 refractory aggregates were synthesized from industrial ZnO and reactive Al 2 O 3 by two-stage firing at 1050 °C and 1700 °C resulting in 0% open porosity. The ZnAl 2 O 4 powder calcined at 1050 °C is also a good refractory matrix material as it has better sinterability than preformed refractory-grade MgAl 2 O 4 and calcined alumina. The thermal expansion coefficient of ZnAl 2 O 4 aggregate in the range of 70–1600 °C was found to be 10.7 × 10 –6 K –1 , which is similar to tabular Al 2 O 3 (10.3 × 10 –6 K –1 ) and MgAl 2 O 4 (10.3 × 10 –6 K –1 ), but lower than dead burned MgO (16.4 × 10 –6 K –1 ), creating the possibility of developing thermal shock resistant refractories by utilizing this mismatch.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Demonstration of an All-Refractory Corrosion-Resistant Molten Salt Pumping and Storage Infrastructure Up to 950 degrees C

Concentrating solar power (CSP) with thermal energy storage (TES) has an estimated cost similar to solar photovoltaics (PV) with lithium-ion batteries (LIB), but CSP + TES has the potential for significantly reduced cost by operating above 700 degrees C. However, this requires a TES medium and containment infrastructure which are chemically compatible and do not degrade above 700 degrees C. MgCl2-KCl-NaCl (MKN) salt is a promising medium, but when MKN salt has small amounts of water and oxygen dissolved in it, it excessively corrodes conventional commercial alloys. Here, we consider refractory materials including graphite, carbon-carbon composite (C/C), and molybdenum because they maintain high mechanical strength at elevated temperatures and are expected to resist corrosion by MKN salt. While selection of refractory materials is often constrained by the need to remain chemically stable in air, this work uses an enclosure filled with inert gas to allow the use of materials like graphite and molybdenum. Notably, graphite components can seal against liquids unlike many brittle refractory materials. We demonstrate a centrifugal pump and mechanical seals made of refractory materials in a laboratory-scale circulation loop, which successfully operated continuously for more than 49 h at temperatures ranging from 750 degrees C to 950 degrees C with no mechanical failures or chemical degradation of the refractory materials. To the best of our knowledge, this is the highest temperature molten salt circulation loop that has been successfully developed, and this refractory infrastructure allows for operation at even much higher temperatures (<1600 degrees C) if a storage medium with a lower vapor pressure is used. The principles of this architecture are relevant to other applications with high temperature flowing metals and salts including Generation IV nuclear fission reactors for power production and molten salt electrolysis reactors for metallurgical processing.

14 SOLAR ENERGY↗
DOE OSTI2020

Technical Performance of Refractory Liners for Molten Chloride Salt Thermal Energy Storage Systems

A chloride-based molten-salt system that uses a ternary blend of MgCl2/KCl/NaCl is investigated to provide higher temperature thermal energy storage capability. Despite higher thermal stability, molten chlorides present several unique challenges, including the design of internal refractory-ceramic liners to prevent the corrosion and thermal stress of alloy tank shells. This work discusses issues and potential solutions related to containment of molten chloride salt, specifically the optimization of the refractory material at the molten salt interface (hot face). The down-selected hot face candidate limits permeation of salt through the material and forms a highly stable secondary surface phase in equilibrium with the molten salt. A mortar is created using the corrosion resistant hot face brick. Brick and mortar composite are subjected to mechanical stress/strain analysis, in order to calculate composite material properties and better inform thermomechanical models. The U.S. Department of Energy Generation 3 (DOE Gen3) program seeks to develop higher efficiency CSP plants that can provide cost-competitive, flexible power in the U.S. electric grid. The proposed Gen3 Liquid Pathway CSP plant closely resembles the configuration of current nitrate salt power towers with two-tank storage (Gen2). The differences between Gen2 and Gen3 include the types of compatible materials used in salt storage tank construction. Stainless steel loses strength at Gen3 temperatures, and although nickel superalloys would be capable of withstanding sustained high temperatures, these materials are prohibitively expensive at scale. Uninsulated tank shells also pose a significant risk as common steels are highly susceptible to chemical attack from molten chloride salt. To address these concerns, refractory-ceramic based containment materials are proposed to line the inside of the hot and cold storage tanks. In doing so, stainless or carbon steel shells may be used in construction depending on the level of insulation provided. The composition of the internal liner requires careful consideration to maximize the efficacy of multiple parameters including corrosion resistance, strength at operating temperature, durability, and cost. This is particularly true for the material at the interface with the salt, known as the "hot face", which is responsible for protecting the insulating layers between the tank shell and the hot face brick layer. The molten salt in this system is superheated over 300 °C above its freeze temperature. Therefore, unlike other industrial processes which use refractory-lined vessels, it is not expected that a freeze plane will develop in the hot face. Therefore, the hot face must be designed to withstand chemical corrosion and inhibit permeation of molten salt into the insulating layers. A down selection was performed to identify a hot face candidate best equipped to maintain thermal, mechanical, and chemical integrity when exposed to molten salt over extended periods of time. Long-duration chemical capability experiments were conducted with the down selected hot face refractory fully immersed in molten chloride salt for up to 3000 hours. The average salt penetration does not exceed 100 microns. When extrapolated to 20 and 30 years of continuous exposure, the expected salt penetration depth is approximately 2.0 mm and 2.9 mm, respectively. A magnesium-rich secondary phases develops at the salt/refractory interface. X-ray diffraction identifies the material as forsterite (Mg2SiO4), which is reported to form synthetically in molten chloride salt solutions. These results suggest the selected hot face will adequately inhibit salt permeation. While there is optimism that the hot face brick will inhibit salt permeation, mortar joints are typically the weakest point of a refractory brick liner. From a thermochemical perspective, differing thermal expansion coefficients may result in the mortar and brick to grow independent of each other, creating gaps through which molten salt can penetrate. To address this issue, NREL has developed an in-house mortar composed of the down selected hot face brick that has been shown to be compatible with the salt. Compressive stress/strain analyses have been performed on the brick/ mortar composites to generate stress/strain curves. Modulus of elasticity and Poisson's ratio of the composite may be calculated from the stress/strain curves, in order to provide more representative data to finite element mechanical models for accurate approximation of stress on the tank shell and the amount of thermal expansion expected within the tank liner.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2022

A phase 2 study of sorafenib combined with conventional therapies in refractory central nervous system leukemia

Background Patients with refractory central nervous system leukemia (CNSL) have a dismal prognosis and lack effective therapy. Case reports have shown that sorafenib is effective against brain metastases, including leukemia. Methods To explore the efficacy of sorafenib combined with conventional therapies for refractory CNSL, a phase 2 study was conducted. The primary end point was the complete remission rate (CRR) within 8 weeks of treatment. Secondary end points included the overall response rate (ORR), event‐free survival (EFS), overall survival (OS), and adverse events (AEs). Results Twenty‐six patients with refractory CNSL were enrolled; they included 17 with isolated CNSL, 7 with hematological relapse, and 2 with another extramedullary relapse. After 8 weeks of treatment, 21 patients achieved complete remission, 2 achieved partial remission, and 3 achieved no remission for a CRR of 80.8% (95% CI, 62.1%‐91.5%) and an ORR of 88.5% (95% CI, 71.0%‐96.0%). Twenty patients survived, and 6 died. The 2‐year EFS and OS rates were 75.0% (95% CI, 54.5%‐88.3%) and 76.9% (95% CI, 54.2%‐90.4%), respectively. Six patients experienced grade 3 or 4 treatment‐related AEs, including moderate chronic graft‐vs‐host disease (n = 3), grade 3 or 4 acute graft‐vs‐host disease (n = 2), and grade 3 skin rash (n = 1). No treatment‐related deaths occurred during the therapy of refractory CNSL. Conclusions Sorafenib combined with conventional therapies is effective and safe for refractory CNSL. Lay Summary Sorafenib combined with conventional therapies is effective and safe for refractory central nervous system leukemia.

Chen, Xiaoxia↗