Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reactivity Coefficients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Quantifying Sources and Sinks of Reactive Gases in the Lower Atmosphere Using Airborne Flux Observations

Atmospheric composition is governed by the interplay of emissions, chemistry, deposition, and transport. Substantial questions surround each of these processes, especially in forested environments with strong biogenic emissions. Utilizing aircraft observations acquired over a forest in the southeast U.S., we calculate eddy covariance fluxes for a suite of reactive gases and apply the synergistic information derived from this analysis to quantify emission and deposition fluxes, oxidant concentrations, aerosol uptake coefficients, and other key parameters. Evaluation of results against state-of-the-science models and parameterizations provides insight into our current understanding of this system and frames future observational priorities. As a near-direct measurement of fundamental process rates, airborne fluxes offer a new tool to improve biogenic and anthropogenic emissions inventories, photochemical mechanisms, and deposition parameterizations.

emission↗
NASA NTRS1986

Lubricant and additive effects on spur gear fatigue life

Spur gear endurance tests were conducted with six lubricants using a single lot of consumable-electrode vacuum melted (CVM) AISI 9310 spur gears. The sixth lubricants was divided into four batches each of which had a different additive content. Lubricant tested with a phosphorus-type load carrying additive showed a statistically significant improvement in life over lubricants without this type of additive. The presence of sulfur type antiwear additives in the lubricant did not appear to affect the surface fatigue life of the gears. No statistical difference in life was produced with those lubricants of different base stocks but with similar viscosity, pressure-viscosity coefficients and antiwar additives. Gears tested with a 0.1 wt pct sulfur and 0.1 wt pct phosphorus EP additives in the lubricant had reactive films that were 200 to 400 (0.8 to 1.6 microns) thick.

Townsend, D. P.↗
NASA NTRS1982

A specific radioimmunoassay for osteocalcin with advantageous species crossreactivity

The specificities of immunoassays to rat and bovine osteocalcin are examined. Extracts of noncalcified tissues and tissue fractions are unreactive to the antibody, with the exception of the kidney, in which the reactive component appears to be identical with osteocalcin by gel filtration and dose dilution analysis. The assays, developed against protein isolated from bone, are also demonstrated to be reactive to the native protein (bone in situ) and to osteocalcin in serum. The assays are sensitive to less than 50 pg osteocalcin. Intra- and interassay coefficients of variation are less than 6.8%. The bovine antibody crossreacts with human, horse, monkey, baboon, and cat osteocalcin, while the rat antibody crossreacts with dog and mouse.

Patterson-Allen, P.↗
NASA NTRS2001

Methanol Uptake By Low Temperature Aqueous Sulfuric Acid Solutions

To evaluate the role of upper tropospheric and lower stratospheric aerosols in the global budget of methanol, the solubility and reactivity of CH3OH in aqueous sulfuric acid solutions are under investigation. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H(*), for methanol dissolution into 45 to 70 percent by weight H2SO4. We find that methanol solubility ranges from 10(exp 5) to 10(exp 8) M/atm and increases with decreasing temperature and with increasing sulfuric acid content. These solubility measurements include uptake due to physical solvation and all rapid equilibria which are established in solution. Our data indicate that simple uptake by aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These results differ from those recently reported in the literature, and an explanation of this disparity will be presented. In addition to solvation, reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H may proceed in the atmosphere but is not significant under our experimental conditions. Results obtained using a complementary equilibrium measurement technique confirm this directly. In addition, the extent of methanol sequestration via formation of mono- and dimethylsulfate will be evaluated under several atmospheric conditions.

Iraci, Laura T.↗
NASA NTRS1973

System statistical reliability model and analysis

A digital computer code was developed to simulate the time-dependent behavior of the 5-kwe reactor thermoelectric system. The code was used to determine lifetime sensitivity coefficients for a number of system design parameters, such as thermoelectric module efficiency and degradation rate, radiator absorptivity and emissivity, fuel element barrier defect constant, beginning-of-life reactivity, etc. A probability distribution (mean and standard deviation) was estimated for each of these design parameters. Then, error analysis was used to obtain a probability distribution for the system lifetime (mean = 7.7 years, standard deviation = 1.1 years). From this, the probability that the system will achieve the design goal of 5 years lifetime is 0.993. This value represents an estimate of the degradation reliability of the system.

Lekach, V. S.↗
NASA NTRS1990

Micromechanical thermal analysis of interphase region in a titanium aluminide MMC

The high reactivity between the fiber and matrix in silicon carbide/titanium aluminide MMCs leads to the formation of brittle reaction products at the fiber/matrix (F/M) interface. Also, the high thermal expansion coefficient mismatch between the fiber and matrix leads to high tensile residual stresses at the F/M interface, and this can lead to premature cracking during cooldown. One solution to these problems is the use of a metallic fiber coating like Ta which acts as an F/M diffusion barrier and reacts with the matrix to form a beta stabilized compliant layer. A finite element micromechanics analysis was performed to study the effects of Ta and beta interphase layers on the thermal residual stresses during consolidation. A 5-micron-thick beta layer reduced cool-down stresses by 8 percent compared to a 2 percent reduction computed for a Ta layer of the same thickness. Plastic yielding in the Ta was not effective in reducing cool-down stresses. Compliant alpha-2 particles next to the stiffer gamma particles reduced stresses in the gamma particles by less than 2 percent. A simple closed form analysis was developed to calculate thermal residual stresses in a fiber/interphase/matrix system. A 2-micron-thick Ag interphase layer was found to reduce residual stresses by about 11 percent.

Naik, R. A.↗
NASA NTRS1997

TBIEM3D: A Computer Program for Predicting Ducted Fan Engine Noise

This document describes the usage of the ducted fan noise prediction program TBIEM3D (Thin duct - Boundary Integral Equation Method - 3 Dimensional). A scattering approach is adopted in which the acoustic pressure field is split into known incident and unknown scattered parts. The scattering of fan-generated noise by a finite length circular cylinder in a uniform flow field is considered. The fan noise is modeled by a collection of spinning point thrust dipoles. The program, based on a Boundary Integral Equation Method (BIEM), calculates circumferential modal coefficients of the acoustic pressure at user-specified field locations. The duct interior can be of the hard wall type or lined. The duct liner is axisymmetric, locally reactive, and can be uniform or axially segmented. TBIEM3D is written in the FORTRAN programming language. Input to TBIEM3D is minimal and consists of geometric and kinematic parameters. Discretization and numerical parameters are determined automatically by the code. Several examples are presented to demonstrate TBIEM3D capabilities.

Dunn, M. H.↗
NASA NTRS2001

Fitting Vibrational Energy Parameters to Falloff Experiments: CH3 + CH3 + He (0.6-2 Torr 200-298 K)

There are many reported experiments and theoretical calculations for the combination of methyl free radicals diluted in a non-reactive 'deactivator. At high pressure the ethane (C2H6) combination product is the sole product; with decreasing pressure the chemically activated C2H6 will decompose. The falloff in the observed rate coefficient is the result of the competition between collisional stabilization of the chemically activated CA and unimolecular decomposition. The dependence of the rate coefficient on pressure, temperature and collision properties is complex and can not be calculated from first principles. The understanding of this system is not only of fundamental importance but is relevant to the recent detection of methyl free radicals in the atmospheres of Saturn - and Neptune. The temperatures of these outer planet atmospheres are in the 140-200 K region with total pressures (predominately H2 and He) less than 0.2 Torr. Experimentally determined rate coefficients have been reported for this reaction at T = 296-906 K and T = 200-408 K mostly with argon as the deactivator. At T = 200 K only the high pressure rate coefficient has been determined. Complete falloff curves over a wide temperature range (200-1600 K) with a variety of weak collider models used to simulate argon as the deactivator have also been reported by Klippenstein and Harding (KH). More recently we have reported the experimental rate coefficients in the falloff region with helium as the deactivator at 200 and 298 K. In this paper we have used the calculated falloff curves reported by KH for argon to determine the average energy transferred per collision for helium in our recently reported experiments. Collision rates were converted using Lennard Jones parameters; the temperature dependence of this conversion factor is noted. The helium experiments were consistent with a down of approximately 100 cm (exp-1); the temperature dependence was slight. The magnitude of down and its temperature dependence will be compared to other systems with similar substrate complexity and reaction energetics.

Tardy, Dwight C.↗
NASA NTRS1994

Optical and Electrical Properties of Reactively Sputtered TiN, ZrN, and HfN Thin Films

Thin films of titanium, zirconium, and hafnium nitride are prepared by DC magnetron reactive sputtering at room temperature on fused silica, optical glass, and silicon substrates. Deposition parameters are investigated in order to obtain stoichiometric films. The optical and electrical properties of the films as a function of nitrogen partial pressure are determined. The results show that an inverse correlation exists between the optical reflectance and the electrical resistivity of the films. Ellipsometer data for all three films show that their refractive index in the visible spectrum is decreased by increasing the film thickness while the extinction coefficient is unchanged. Thin films of TiN have the lowest room temperature resistivity relative to ZrN and HfN thin films.

Reactive↗
NASA NTRS1973

Dynamic analysis of an open-cycle gas-core nuclear rocket

Reactivity and flow disturbances were used to investigate the transient response of a conceptual open cycle gas core nuclear rocket engine. The disturbances were made with the system initially operating at its steady state design point. Results of the study show that the feedbacks associated with the propellant density and propellant temperature have a dominant effect on the response of the system. Furthermore, there appears to be a rather limited range of values of these propellant feedback coefficients for which the gas core nuclear rocket has a stable response. The system was rather insensitive to a fuel flow rate disturbance, whereas a similar disturbance in the propellant flow rate caused large changes in reactor power. For a similar disturbance in the propellant flow rate caused large changes in reactor power. For most reactivity and flow rate disturbances, the response showed oscillations of various intensity.

Turney, G. E.↗
NASA NTRS1993

Molecular processes in comets

Classical trajectory calculations of the cross sections for vibrational and rotational energy exchange in direct and reactive collisions of hydrogen atoms and hydrogen molecules have been carried out. To test the sensitivity, three potential energy surfaces have been used. For the exchange transitions which occur at small internuclear distances, the rate coefficients for the three surfaces agree quite well. For the direct transitions, there are significant differences for the pure rotational transitions from j=0 to 2 and from j=1 to j=3 in which there is no change in vibration. For higher j the differences tend to disappear, suggesting that the rotational angular momentum can couple to the orbital angular momentum to overcome the centrifugal barrier. Complete numerically exact quantum mechanical calculations for the process in which vJ changes have been performed. Dr. M. A'Hearn has provided data on the fluorescent population of the NH rotational and fine-structure levels from which we should be able to predict accurate photodissociation lifetimes. The distribution rate of C2 is being investigated. A review of H3(+) in terrestrial and extraterrestrial environments was prepared for a volume of Advances in Atomic, Molecular and Optical Physics.

Dalgarno, A.↗
NASA NTRS1996

Low Temperature Unbalanced Magnetron Deposition of Hard, Wear-Resistant Coatings for Liquid-Film Bearing Applications

The original program for evaluating the tribological properties several different hard coatings for liquid film bearing applications was curtailed when the time for the program was reduced from 3 years to 1. Of the several different coatings originally planned for evaluation, we decided to concentrate on one coating, carbon nitride. At BIRL, we have been instrumental in the development of reactively sputtered carbon nitride coatings, and we have found that it is a very interesting new material with very good tribological properties. In this program, we found that the reactively sputtered carbon nitride does not bond well directly to hardened 440C stainless steel; but if an interlayer of titanium nitride is added between the carbon nitride and the 440C, the adhesion of the dual coating combination is very good. Statistically designed experiments were run with the dual layer combination, and 3 variables were chosen for the Box-Benken design, which were the titanium nitride interlayer thickness, the nitrogen partial pressure during the reactive sputtering of the carbon nitride, and the carbon nitride substrate bias voltage. Two responses were studied from these three variables; the adhesion of the dual coating combination to the 440C substrate and the friction coefficient of the carbon nitride in dry sliding contact with 52100 steel in air. The best adhesion came with the thickness interlayer thickness studied, which was 4 micrometers, and the lowest coefficient of friction was 0.1, which was achieved when the bias voltage was in the range of -80 to - 120 V and the nitrogen partial pressure was 3 mTorr.

Sproul, William D.↗
NASA NTRS1998

The Improvement of Ion Plated Ag and Au Film Adherence to Si3N4 and SiC Surfaces for Increased Tribological Performance

A modified dc-diode plating system, utilizing a metallic screen cage as a cathode and referred as SCREEN CAGE ION PLATING (SCIP), is used to deposit Ag and Au lubricating films on Si3N4 and SiC surfaces. When deposition is performed in Ar or N2, glow discharge, the surface displays poor adhesive strength (less than 5 MPa). A dramatic increase in adhesive strength (less than 80 MPa) is achieved when plating is performed in a reactive 50% 02 + 50% Ar glow discharge. The excited/ionized oxygen species (O2(+)/O(+) in the glow discharge contribute to the oxidation of the Si3N4 or SiC surfaces as determined by X-ray Photoelectron Spectroscopy (XTS) depth profiling. The reactively sputter-oxidized S3N4 or SiC surfaces and the activated-oxidized-metastable Ag or Au species formed in the plasma cooperatively contribute to the increased adherence. As a result, the linear thermal expansion coefficient mismatch at the interface is reduced. These lubricating Ag and Au films under sliding conditions reduce the friction coefficient by a factor of 2-1/2 to 4.

Spalvins, Talivaldis↗
NASA NTRS1977

Odd nitrogen in the mesosphere and thermosphere - Its chemistry and transport

The atomic nitrogen in the thermosphere, which is produced either in its ground term or in a highly reactive metastable term, reacts with molecular oxygen to form nitric oxide and atomic oxygen. However, nitric oxide is destroyed in reactions with atomic nitrogen in which molecular nitrogen and atomic oxygen is formed. Adopted reactions and rate coefficients for odd nitrogen chemistry are listed in a table. An analysis is conducted of the temperature distribution below 150 km and its effect on the odd nitrogen chemistry. The latitudinal distribution of nitric oxide is discussed. Satellite measurements have shown that nitric oxide concentrations at high latitudes are highly variable in both time and space. Their average concentrations are 3-4 times higher than at mid-latitudes. The measured variation of nitric oxide density as a function of latitude is shown in a graph.

Rusch, D. W.↗
NASA NTRSDate not supplied

Validated Reduced Computational Methods for Realistic RDC Injection Modeling

This paper outlines a simplified computational method without chemistry for single and multi-injector performance for rotating detonation combustion (RDC) environment as well as relevant performance metrics. For non-reactive cases, an unsteady pressure profile from a Method of Characteristics (MOC) simulation was used to simulate an RDC combustion wave travelling around the annulus. In reactive cases, a pre-mixed stoichiometric mixture of hydrogen and air is injected into a 2D unwrapped combustion chamber with a specified injector area. The performance is evaluated based on several performance metrics including unsteady discharge coefficient, average mass flux coming into the combustor, and percentage time obstructed. Finally, the computational method was validated through an experimental RDC test setup with a single element injector in a hydrogen-air detonation driver environment.

Propulsion↗
NASA NTRS1990

Synthesis and structures of metal chalcogenide precursors

The reactivity of early transition metal sandwich complexes with sulfur-rich molecules such as dithiocarboxylic acids was studied. Researchers recently initiated work on precursors to CuInSe2 and related chalcopyrite semiconductors. Th every high radiation tolerance and the high absorption coefficient of CuInSe2 makes this material extremely attractive for lightweight space solar cells. Their general approach in early transition metal chemistry, the reaction of low-valent metal complexes or metal powders with sulfur and selenium rich compounds, was extended to the synthesis of chalcopyrite precursors. Here, the researchers describe synthesis, structures, and and routes to single molecule precursors to metal chalcogenides.

Hepp, Aloysius F.↗
NASA NTRS1981

Review of literature surface tension data for molten silicon

Measurements of the surface tension of molten silicon are reported. For marangoni flow, the important parameter is the variation of surface tension with temperature, not the absolute value of the surface tension. It is not possible to calculate temperature coefficients using surface tension measurements from different experiments because the systematic errors are usually larger than the changes in surface tension because of temperature variations. The lack of good surface tension data for liquid silicon is probably due to its extreme chemical reactivity. A material which resists attack by molten silicon is not found. It is suggested that all of the sessile drip surface tension measurements are probably for silicon which is contaminated by the substrate materials.

Hardy, S.↗
NASA NTRS1994

Theoretical determination of chemical rate constants using novel time-dependent methods

The work completed within the grant period 10/1/91 through 12/31/93 falls primarily in the area of reaction dynamics using both quantum and classical mechanical methodologies. Essentially four projects have been completed and have been or are in preparation of being published. The majority of time was spent in the determination of reaction rate coefficients in the area of hydrocarbon fuel combustion reactions which are relevant to NASA's High Speed Research Program (HSRP). These reaction coefficients are important in the design of novel jet engines with low NOx emissions, which through a series of catalytic reactions contribute to the deterioration of the earth's ozone layer. A second area of research studied concerned the control of chemical reactivity using ultrashort (femtosecond) laser pulses. Recent advances in pulsed-laser technologies have opened up a vast new field to be investigated both experimentally and theoretically. The photodissociation of molecules adsorbed on surfaces using novel time-independent quantum mechanical methods was a third project. And finally, using state-of-the-art, high level ab initio electronic structure methods in conjunction with accurate quantum dynamical methods, the rovibrational energy levels of a triatomic molecule with two nonhydrogen atoms (HCN) were calculated to unprecedented levels of agreement between theory and experiment.

Dateo, Christopher E.↗