Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Factors Controlling Stress Rupture of Fiber-Reinforced Ceramic Composites

The successful application of fiber-reinforced ceramic matrix composites (CMC) depends strongly on maximizing material rupture life over a wide range of temperatures and applied stresses. The objective of this paper is to examine the various intrinsic and extrinsic factors that control the high-temperature stress rupture of CMC for stresses below and above those required for cracking of the 0 C plies (Regions I and II, respectively). Using creep-rupture results for a variety of ceramic fibers and rupture data for CMC reinforced by these fibers, it is shown that in those cases where the matrix carries little structural load, CMC rupture conditions can be predicted very well from the fiber behavior measured under the appropriate test environment. As such, one can then examine the intrinsic characteristics of the fibers in order to develop design guidelines for selecting fibers and fiber microstructures in order to maximize CMC rupture life. For those cases where the fiber interfacial coatings are unstable in the test environment, CMC lives are generally worse than those predicted by fiber behavior alone. For those cases where the matrix can support structural load, CMC life can even be greater provided matrix creep behavior is properly controlled. Thus the achievement of long CMC rupture life requires understanding and optimizing the behavior of all constituents in the proper manner.

DiCarlo, J. A.↗

Composite Overwrap Pressure Vessels: Mechanics and Stress Rupture Lifing Philosophy

The NASA Engineering and Safety Center (NESC) has been conducting an independent technical assessment to address safety concerns related to the known stress rupture failure mode of filament wound pressure vessels in use on Shuttle and the International Space Station. The Shuttle's Kevlar-49 fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar-49 filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of load sharing liners and the complex manufacturing procedures, the state of actual fiber stress in flight hardware and test articles is not clearly known. Indeed non-conservative life predictions have been made where stress rupture data and lifing procedures have ignored the contribution of the liner in favor of applied pressure as the controlling load parameter. With the aid of analytical and finite element results, this paper examines the fundamental mechanical response of composite overwrapped pressure vessels including the influence of elastic-plastic liners and degraded/creeping overwrap properties. Graphical methods are presented describing the non-linear relationship of applied pressure to Kevlar-49 fiber stress/strain during manufacturing, operations and burst loadings. These are applied to experimental measurements made on a variety of vessel systems to demonstrate the correct calibration of fiber stress as a function of pressure. Applying this analysis to the actual qualification burst data for Shuttle flight hardware revealed that the nominal fiber stress at burst was in some cases 23% lower than what had previously been used to predict stress rupture life. These results motivate a detailed discussion of the appropriate stress rupture lifing philosophy for COPVs including the correct transference of stress rupture life data between dissimilar vessels and test articles.

Thesken, John C.↗

Composite Overwrap Pressure Vessels: Mechanics and Stress Rupture Lifting Philosophy

The NASA Engineering and Safety Center (NESC) has been conducting an independent technical assessment to address safety concerns related to the known stress rupture failure mode of filament wound pressure vessels in use on Shuttle and the International Space Station. The Shuttle s Kevlar-49 (DuPont) fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar-49 filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of load sharing liners and the complex manufacturing procedures, the state of actual fiber stress in flight hardware and test articles is not clearly known. Indeed nonconservative life predictions have been made where stress rupture data and lifing procedures have ignored the contribution of the liner in favor of applied pressure as the controlling load parameter. With the aid of analytical and finite element results, this paper examines the fundamental mechanical response of composite overwrapped pressure vessels including the influence of elastic plastic liners and degraded/creeping overwrap properties. Graphical methods are presented describing the non-linear relationship of applied pressure to Kevlar-49 fiber stress/strain during manufacturing, operations and burst loadings. These are applied to experimental measurements made on a variety of vessel systems to demonstrate the correct calibration of fiber stress as a function of pressure. Applying this analysis to the actual qualification burst data for Shuttle flight hardware revealed that the nominal fiber stress at burst was in some cases 23 percent lower than what had previously been used to predict stress rupture life. These results motivate a detailed discussion of the appropriate stress rupture lifing philosophy for COPVs including the correct transference of stress rupture life data between dissimilar vessels and test articles.

Thesken, John C.↗

The Inclusion of Arbitrary Load Histories in the Strength Decay Model for Stress Rupture

Stress rupture is a failure mechanism where failures can occur after a period of time, even though the material has seen no increase in load. Carbon/epoxy composite materials have demonstrated the stress rupture failure mechanism. In a previous work, a model was proposed for stress rupture of composite overwrap pressure vessels (COPVs) and similar composite structures based on strength degradation. However, the original model was limited to constant load periods (holds) at constant load. The model was expanded in this paper to address arbitrary loading histories and specifically the inclusions of ramp loadings up to holds and back down. The broadening of the model allows for failures on loading to be treated as any other failure that may occur during testing instead of having to be treated as a special case. The inclusion of ramps can also influence the length of the "safe period" following proof loading that was previously predicted by the model. No stress rupture failures are predicted in a safe period because time is required for strength to decay from above the proof level to the lower level of loading. Although the model can predict failures during the ramp periods, no closed-form solution for the failure times could be derived. Therefore, two suggested solution techniques were proposed. Finally, the model was used to design an experiment that could detect the difference between the strength decay model and a commonly used model for stress rupture. Although these types of models are necessary to help guide experiments for stress rupture, only experimental evidence will determine how well the model may predict actual material response. If the model can be shown to be accurate, current proof loading requirements may result in predicted safe periods as long as 10(13) years. COPVs design requirements for stress rupture may then be relaxed, allowing more efficient designs, while still maintaining an acceptable level of safety.

Reeder, James R.↗

Mechanics and Chemistry: Sinle Molecule Bond Rupture Forces Correlate with Molecular Backbone Structure

We simultaneously measure conductance and force across nanoscale junctions. A new, two-dimensional histogram technique is introduced to statistically extract bond rupture forces from a large data set of individual junction elongation traces. For the case of Au point contacts, we find a rupture force of 1.4 {+-} 0.2 nN, which is in good agreement with previous measurements. We then study systematic trends for single gold metal-molecule-metal junctions for a series of molecules terminated with amine and pyridine linkers. For all molecules studied, single molecule junctions rupture at the Au-N bond. Selective binding of the linker group allows us to correlate the N-Au bond-rupture force to the molecular backbone. We find that the rupture force ranges from 0.8 nN for 4,4' bipyridine to 0.5 nN in 1,4 diaminobenzene. These experimental results are in excellent quantitative agreement with density functional theory based adiabatic molecular junction elongation and rupture calculations.

36 MATERIALS SCIENCE↗

Inferior Vena Cava Rupture Caused by Balloon Angioplasty During the Treatment of Budd–Chiari Syndrome

Objective: Percutaneous transluminal balloon angioplasty (PTA) is the main treatment option for Budd–Chiari syndrome (BCS) with inferior vena cava (IVC) obstruction. However, IVC rupture caused by PTA has never been reported. Materials and Methods: Between August 2004 and December 2016, a consecutive cohort of 617 BCS patients with obstructed IVC who underwent PTA with or without stent placement were reviewed retrospectively to identify IVC rupture. Pre- and post-procedural imaging data, clinical and procedural technical data were analyzed. Results: Of the 617 BCS patients, five patients had IVC rupture caused by PTA (0.81%). Four of these patients had retroperitoneal, intra-hepatic IVC rupture without extravasation into abdominal cavity which was successfully managed conservatively. One patient had supra-hepatic IVC rupture into the pericardial cavity which was surgically treated. Conclusion: IVC rupture is a rare complication of PTA treatment of BCS and most commonly located at the intra-hepatic IVC caused by oversized balloons which does not require additional treatment.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Influence of Melt Superheating Treatment on Solidification Characteristics and Rupture Life of a Third-Generation Ni-Based Single-Crystal Superalloy

The influence of melt superheating treatment on the melt properties, solidification characteristics, and rupture life of a third-generation Ni-based single-crystal superalloy was investigated to reveal the critical temperature range of melt structure evolution and its effect on rupture life. The results showed that the viscosity of superalloy decreased but the surface tension increased with increasing superheating temperature. Two characteristic temperature points where the melt viscosity and undercooling degree suddenly change were determined to be 1600 °C and 1700 °C, respectively. Similarly, the stability of the solidification interface firstly improved and then weakened with increasing superheating temperature. The dendrite arms were well refined and the segregation was reduced at 1700 °C. In addition, the rupture life obtained at 1100 °C and 137 MPa increased by approximately 30 pct, approaching the rupture life of the corresponding superalloy containing 2 pct Ru, with increasing superheating temperature from 1500 °C to 1700 °C. When the melt was further heated to 1800 °C, the rupture life decreased. The evolutions of solidification characteristics and rupture life with increasing melt superheating temperature were attributed to changes in the melt structure.

36 MATERIALS SCIENCE↗

Comparative Evaluation of Creep-Rupture Behavior of P9 Steel Plate and Thick Section Tubeplate Forging

In the present investigation, creep-rupture behavior of P9 steel in two different product forms of 20-mm plate and 300-mm-thick tubeplate forging has been studied at 793 and 873 K. It has been found that steady-state creep rate and rupture life followed power law dependence on applied stress at low and high stress regimes for both forms of products. At high stress regime, P9 steel plate exhibited better creep strength with respect to tubeplate forging in terms of lower creep rate and higher rupture life at 793 and 873 K. On contrary, both product forms exhibited similar creep rate and rupture behavior in the low stress regime at 873 K. Difference in creep ductility has been found to be insignificant in both product forms. Irrespective of test conditions and product forms, fracture appearance remained transgranular ductile characterized by dimples. The comparative evaluation of creep-rupture properties of both product forms has also been described in terms of creep rate-rupture life relationships of Monkman–Grant type, creep damage tolerance and tertiary creep characteristics at 793 and 873 K.

36 MATERIALS SCIENCE↗

Microstructure and deformation mode of a stainless steel rupture disc exposed to sodium-water reaction

This paper deals with microstructural studies carried out on an austenitic stainless steel rupture disc which was exposed to sodium-water reaction. The rupture disc was part of a leak simulator put in a micro leak test section which was used to study the 'self wastage' of steam generator tubes. During micro leak testing, the rupture disc failed exhibiting a linear crack at a much lower pressure of 10 MPa rather than bursting open at the higher designed pressure of 15 MPa. The failed rupture disc revealed different microstructural features on the inner (steam exposed) and outer (sodium exposed) surfaces. Using microstructure as the signature, the temperature experienced by the rupture disc was predicted as {>=} 1273 K. Evidence for the exposure of the rupture disc to highly exothermic sodium-water reaction was obtained in the form of sodium rich debris, microcracks and deformation bands. Detailed transmission electron microscopy revealed the nature of deformation bands as deformation twins which is not a preferred failure mode for austenitic stainless steels.

36 MATERIALS SCIENCE↗

Rupture Orientation and Strain-induced Crystallization of Polymer Chain and Network in Vulcanized Polyisoprene During Uniaxial Deformation by in-situ Electron Spin Resonance(ESR) and Synchrotron X-ray Analysis

Different network structures of vulcanized polyisoprene rubbers were studied by in-situ ESR and synchrotron X-ray during deformation to analyze the rupture, orientation, and strain-induced crystallization of polymer chains and network points. Rupture of network points occur, depending on network structure, and create an un-reversible change in vulcanized rubber. The flexibility of network points affects the possibility of rupture, polymer orientation and strain-induced crystallization. Peroxide vulcanized network is rigid and un-rupturable. Poly-sulfide rich vulcanized network is more flexible and less rupturable than mono-sulfide rich vulcanized network. Chain flexibility and rupturability of network points affect the strain-induced crystallization and stress-strain relation.

36 MATERIALS SCIENCE↗

Earthquake Damage Patterns Resolve Complex Rupture Processes

Fracture damage patterns around faults induced by dynamic earthquake rupture are an invaluable record to clarify the rupture process on complex fault networks. The 2016 M w 7.8 Kaikōura earthquake in New Zealand has been reported as one of the most complex earthquakes ever documented that ruptured at least 15 crustal faults. High-resolution optical satellite image displacement maps provide distinctive profiles of displacement across the faults and help visualize the off-fault damage pattern. They are combined with field observation and coupled with a numerical tool that captures the dynamics of the rupture and simultaneous activation of off-fault damage to allow the determination of the most likely rupture scenario. Lastly, this study demonstrates that complex rupture processes can be explained in a rather simple way via a synergetic combination of state-of-the-art observation and first principle physics-based numerical modeling of off-fault damage.

58 GEOSCIENCES↗

Time-resolved observation of thermally activated rupture of a capillary-condensed water nanobridge

The capillary-condensed liquid bridge is one of the most ubiquitous forms of liquid in nature and contributes significantly to adhesion and friction of biological molecules as well as microscopic objects. Despite its important role in nanoscience and technology, the rupture process of the bridge is not well understood and needs more experimental works. Here, we report real-time observation of rupture of a capillary-condensed water nanobridge in ambient condition. During slow and stepwise stretch of the nanobridge, we measured the activation time for rupture, or the latency time required for the bridge breakup. By statistical analysis of the time-resolved distribution of activation time, we show that rupture is a thermally activated stochastic process and follows the Poisson statistics. In particular, from the Arrhenius law that the rupture rate satisfies, we estimate the position-dependent activation energies for the capillary-bridge rupture.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of the Earthquake Rupture on Ground-Motion Variability of the 24 August 2016 M w 6.2 Amatrice, Italy, Earthquake

Here, the devastating 24 August 2016 M w 6.2 earthquake that struck Amatrice, Italy, marked the beginning of a prolonged seismic sequence dominated by three subsequent M w ≥6.0 events in the central Apennines region. The earthquake destroyed Amatrice’s historic center, claiming the lives of 299 individuals and causing widespread damage in the neighboring villages. The severity of the ground shaking, with a recorded maximum acceleration of 850 cm/s 2 on the east–west component at the Amatrice station, was far greater than the predicted acceleration based on the Italian ground-motion model (GMM). As pointed out by several investigations, the observed ground-motion amplitude and its spatial variability during the earthquake can be linked to specific rupture characteristics, including slip distribution and rupture directivity effects revealed by the observed data (Tinti et al., 2016; Pischiutta et al., 2021). In this study, we conducted physics-based 3D numerical simulations of ground motion for the Amatrice earthquake for frequencies up to 3 Hz. We employed a series of kinematic rupture models and a well-constrained local 3D velocity model incorporating surface topography. The kinematic rupture realizations were generated using multiscale hybrid and fully stochastic models, following the technique proposed by Graves and Pitarka (2016). We focused on assessing the sensitivity of near-fault ground-motion amplitudes to earthquake rupture characteristics, in particular, the spatial slip pattern. To evaluate the quality of our simulations, we employed goodness-of-fit measurements performed in comparisons of simulated and recorded ground motions. The simulated ground motions compare well with the recorded data and predictions from GMMs for Italy, ITA18 (Lanzano et al., 2019). However, we found that the simulated interevent ground-motion variability (randomness in the source process) of peak ground velocity, σ (PGV) is higher than the constant σ (PGV) predicted by conventional GMMs. Our simulations using several rupture scenarios demonstrate that the near-fault ground-motion amplification pattern is directly related to the slip distribution pattern.

3D Ground Motions Simulations↗

Accurate Effective Stress Measures: Predicting Creep Life for 3D Stresses Using 2D and 1D Creep Rupture Simulations and Data

Operating structural components experience complex loading conditions resulting in 3D stress states. Current design practice estimates multiaxial creep rupture life by mapping a general state of stress to a uniaxial creep rupture correlation using effective stress measures. The data supporting the development of effective stress measures are nearly always only uniaxial and biaxial, as 3D creep rupture tests are not widely available. This limitation means current effective stress measures must extrapolate from 2D to 3D stress states, potentially introducing extrapolation error. In this work, we use a physics-based, crystal plasticity finite element model to simulate uniaxial, biaxial, and triaxial creep rupture. Here, we use the virtual dataset to assess the accuracy of current and novel effective stress measures in extrapolating from 2D to 3D stresses and also explore how the predictive accuracy of the effective stress measures might change if experimental 3D rupture data was available. We confirm these conclusions, based on simulation data, against multiaxial creep rupture experimental data for several materials, drawn from the literature. The results of the virtual experiments show that calibrating effective stress measures using triaxial test data would significantly improve accuracy and that some effective stress measures are more accurate than others, particularly for highly triaxial stress states. Results obtained using experimental data confirm the numerical findings and suggest that a unified effective stress measure should include an explicit dependence on the first stress invariant, the maximum tensile principal stress, and the von Mises stress.

36 MATERIALS SCIENCE↗

Expression profile analysis of differentially expressed genes in ruptured intracranial aneurysms: In search of biomarkers

Highlights: • Bioinformatics can identify potential biomarkers of ruptured intracranial aneurysm. • BASP1, CD74, CEBPB, ECHDC2, GZMK, HLA-DRB3, KLHL3, SLC2A3 & SOCS3 affect IA rupture. • DEGs are involved in antigen processing and presentation and immune response. • Vascular brain injury affects gene expression in IA tissue. Intracranial aneurysms (IAs) result from the bulging of arterial walls secondary to several factors such as flow, vessel morphology, and genetics. Subarachnoid hemorrhage occurs when such walls rupture, leading to high disability and mortality. Despite numerous investigations pertaining to the relationship between geometric characteristics and IA rupture, only a few have obtained consistent results. This study aimed to further identify the potential genes associated with the pathogenesis of IAs, which may provide novel molecular biomarkers. We downloaded and reanalyzed six datasets, which were divided into four groups. IA walls and blood samples were screened for differentially expressed genes (DEGs); then, functional and pathway enrichment analyses were conducted. In total, 158 common DEGs were identified from Groups 1–3 and 396 genes (187 upregulated and 209 downregulated genes) were differentially expressed in Group 4. The functional analysis revealed that the DEGs were mainly associated with the major histocompatibility complex class II protein complex and antigen processing and presentation. Finally, we identified nine key genes, both in aneurysm tissue samples and blood samples, of which three were mostly associated with the progression and rupture of IAs. Bioinformatics was used to analyze the datasets of the ruptured IAs and identify potential biomarkers, which may provide information for the early detection and treatment of IAs.

60 APPLIED LIFE SCIENCES↗

Induced seismicity provides insight into why earthquake ruptures stop

Injection-induced earthquakes pose a serious seismic hazard but also offer an opportunity to gain insight into earthquake physics. Currently used models relating the maximum magnitude of injection-induced earthquakes to injection parameters do not incorporate rupture physics. We develop theoretical estimates, validated by simulations, of the size of ruptures induced by localized pore-pressure perturbations and propagating on prestressed faults. Our model accounts for ruptures growing beyond the perturbed area and distinguishes self-arrested from runaway ruptures. We develop a theoretical scaling relation between the largest magnitude of self-arrested earthquakes and the injected volume and find it consistent with observed maximum magnitudes of injection-induced earthquakes over a broad range of injected volumes, suggesting that, although runaway ruptures are possible, most injection-induced events so far have been self-arrested ruptures.

58 GEOSCIENCES↗

A Kinematic Rupture Model Generator Using Irikura's Recipe

In this project we developed GEN_SRF4 a computer program for generating kinematic rupture models, compatible with the SRF format, using Irikura and Miyake (2011) asperity-­based earthquake rupture model (IM2011, hereafter). IM2011, also known as Irkura’s recipe, has been widely used to model and simulate ground motion from earthquakes in Japan. An essential part of the method is its kinematic rupture generation technique, which is based on a deterministic rupture asperity modeling approach. The source model simplicity and efficiency of IM2011 at reproducing ground motion from earthquakes recorded in Japan makes it attractive to developers and users of the Southern California Earthquake Center Broadband Platform (SCEC BB platform). Besides writing the code the objective of our study was to test the transportability of IM2011 to broadband simulation methods used by the SCEC BB platform. Here we test it using the Graves and Pitarka (2010) method, implemented in the platform. We performed broadband (0.1- -10 Hz) ground motion simulations for a M6.7 scenario earthquake using rupture models produced with both GEN_SRF4 and rupture generator of Graves and Pitarka (2016), (GP2016 hereafter). In the simulations we used the same Green’s functions, and same high frequency approach for calculating the low-­frequency and high-­frequency parts of ground motion, respectively.

58 GEOSCIENCES↗

Collaborative study on "Earthquake Ground Motion Simulation Using Rupture Dynamics"

California (LLNL) and Disaster Prevention Research Institute, Kyoto University, Japan (DPRI) on rupture dynamics for crustal earthquakes, we carried out analyses of effects of several dynamic rupture parameters, such as stress drop, slip weakening distance and stress excess on fault rupture slip, slip velocity, and rupture velocity. In addition, we examined potential relationships between the assumed initial stress conditions, including asperities location, and rupture initiation and the final slip and slip velocity obtained from the spontaneous rupture modeling.

58 GEOSCIENCES↗