Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RON”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Archived 1976-1985 JPL Aircraft SAR Data

This report describes archived data from the Jet Propulsion Laboratory (JPL) aircraft radar expeditions in the mid-1970s through the mid-1980s collected by Ron Blom, JPL Radar Geologist. The dataset was collected during Ron's career at JPL from the 1970s through 2015. Synthetic Aperture Radar (SAR) data in the 1970s and 1980s were recorded optically on long strips of film. SAR imagery was produced via an optical, holographic technique that resulted in long strips of film imagery.

Thompson, Thomas W.↗
DOE OSTI2021

An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion

This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.

LTHR, RON 90 binary blends, sensitivity analysis↗
DOE OSTI2025

Author Correction: A map of the rubisco biochemical landscape

Correction to: Naturehttps://doi.org/10.1038/s41586-024-08455-0 Published online 22 January 2025. In the version of the article initially published, the affiliations of Hana A. Chang (Department of Plant and Microbial Biology, University of California Berkeley, Berkeley, CA, USA) and Ron Milo (Department of Plant and Environmental Sciences, Weizmann Institute of Science, Rehovot, Israel) were incorrect and have now been amended in the HTML and PDF versions of the article.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2021

Isobutanol Octane Blending Model with Gasoline: Cooperative Research and Development Final Report, CRADA Number CRD-17-00689

The purpose of this agreement between the National Renewable Energy Laboratory (NREL) and Gevo, under the DOE Small Business Vouchers Pilot, is to develop a predictive octane blending model for isobutanol and blendstocks for oxygenated blending (BOBs). Validated models of ethanol octane blending effects are currently used in refinery blending models. While it is known that isobutanol increases octane when blended into BOBs, the effect is non-linear, and dependent on hydrocarbon blendstock properties. Because no predictive model currently exists for isobutanol and BOBs, blenders must perform expensive and time-consuming tests to determine the octane effect on each batch of finished fuel. NREL will make basic measurements of research octane number (RON) and motor octane number (MON) of finished gasoline-isobutanol blends prepared in a broad range of BOBs. The key properties and detailed composition of BOBs utilized will be measured by NREL. Using these measured fuel properties, NREL will develop a predictive octane blending model for isobutanol in BOBs that can be used by terminals to further reduce barriers to market penetration of isobutanol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2012

Ship and Shoot

Ron Woods shared incredibly valuable insights gained during his 28 years at the Kennedy Space Center (KSC) packaging Flight Crew Equipment for shuttle and ISS missions. In particular, Woods shared anecdotes and photos from various processing events. The moral of these stories and the main focus of this discussion were the additional processing efforts and effects related to a "ship‐and‐shoot" philosophy toward flight hardware.

Woods, Ron↗
NASA NTRS2019

Further Development Of Aperture: A Precise Extremely Large Reflective Telescope Using Re-Configurable Elements: NASA Innovative Advanced Concepts (NIAC) - Phase II

One of the pressing needs for space ultraviolet-visible astronomy is a design to allow larger mirrors than the James Webb Space Telescope primary. The diameter of the rocket fairing limits the mirror diameter such that all future missions calling for mirrors up to 16 meters in diameter or larger will require a mirror that is deployed post-launch. In response to the deployment requirement, we address the issues of this concept called "A Precise Extremely Large Reflective Telescope Using Reconfigurable Elements (APERTURE) with both hardware experiments and software simulations... We designed and built several fixtures with O-rings to hold a membrane. We established a coating process to make a membrane that was coated on one side with Cr and the other side with Cr-Terfenol-D-NiCo. The Terfenol-D (T-D hereafter) is the MSM (Magnetic Smart Memory) we use. We bought and established a procedure for measuring a deformation over time and purchased a Shack Hartmann system from Imagine Optic (https://www.imagine-optic.com). The first substrate we used was DuPont (TM) Kapton® polyimide film. Due to material creep, we found the stability over a 48-hour period with a Kapton substrate was not as good as desired (greater than 1 micron). We then switched to CP1 Polyimide. We found the CP1 much more stable to creep, being stable from about 3 hours to 48 hours to within a measurement error to below approximately 0.1 micron. We produced a 13 micron maximum deviation on a 50-millimeter-diameter piece of CP1 (25 microns thick). The T-D coating was about 2 microns, and the other layers, about 10 nanometers. The magnetic field at the base was about 0.1 teslas. We can make the T-D film at least 5 times thicker and the magnetic field at least 5 times stronger, and hence make deformations as much as 25 times larger. We have a formed a collaboration produced at the NIAC (NASA Innovative Advanced Concepts) mid-term review with Dr. Ron Shiri of Goddard Space Flight Center (GSFC) to explore making controlled deviations on lambda/14-lambda/20 scales which are required to bring a surface to the diffraction limit. We carried out only preliminary work on Si using a Coordinate Measuring Machine (CMM), which produced deviations on the 1 micron level. We are still working on a program to bring to GSFC a flat enough (radius of curvature greater than 10 microns) -coated a Si piece with Cr, T-D, NiCo. Then we plan to carry out tests with an interferometer. Further, we formed a new collaboration with Prof. Rajan Vaidyanathan of the University of Central Florida to replace the CP1 with a shape memory alloy (SMA). With his collaboration, we acquired new Federal funding outside of NASA to explore the use of SMAs (we use NiTi). Our preliminary results indicate that we can produce deformations greater than 1 micron on approximately 100 microns thick. Furthermore we have shown that the NiTi can deploy to better than 1 micron of its set original and then trained shape.

Re-Configurable Elements↗
NASA NTRS1998

Manned Mars Landing

Following the first Apollo lunar landing mission in 1969, then Vice-President Spiro Agnew called upon NASA to prepare a plan in 30 days. The action was assigned to the newly formed Program Development Organization. A team was formed to prepare a plan which was completed on time and on August 4, 1969, the plan was presented to The Space Task Group (STG) at NASA HQ by Dr. Wernher Von Braun accompanied by Dr. William Lucas, Ron Harris and Gene Austin. The STG was headed by Dr. George Moeller, then AA in the Office of Manned Space Flight, and composed of other senior NASA officials. The charts in this book are copies of those used in the August 4, 1969 briefing. After this briefing, the MSFC attendees met privately with Dr. Moeller and received further comments/actions. The plan was worked further over the next few weeks and subsequently discussions were held with the Vice President and other White House staff members. While no blanket approval was given to the plan, the need for a reusable Space Shuttle was clearly indicated ass a first step ;in achieving the capability to assemble a Mars ship in Earth orbit. Dr. Moeller hence used this as a strong justification in his successful efforts to sell the Space Shuttle Program.

Mars↗
DOE OSTI2022

Plasma-induced inactivation of Staphylococcus aureus biofilms: The role of atomic oxygen and comparison with disinfectants and antibiotics

Microbial biofilms are of critical concern because of their recalcitrance to antimicrobials. Cold atmospheric plasmas (CAP) represent a promising biofilm remediation strategy as they generate reactive oxygen and nitrogen species (RONS), but mechanisms underpinning CAP-biofilm interactions remain unknown. We assess the impact of treatment modality on biofilm inactivation and show that CAP killing of Staphylococcus aureus biofilms is dependent on treatment conditions, including solution chemistry. In dry treatments, biofilms are locally ablated due to plasma-produced O flux. For saline-submerged biofilms, while we show that ClO – is generated at high concentrations in larger treatment volumes, CAP inactivation at low ClO – concentrations implicates other reaction pathways. Finally, we demonstrate CAP efficacy over conventional antimicrobials, underscoring its promise as a biofilm treatment approach.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗
DOE OSTI2023

A wide range experimental and kinetic modeling study of the oxidation of 2,3-dimethyl-2-butene: Part 1

2,3-Dimethyl-2-butene (TME) is a potential fuel additive with high research octane number (RON) and octane sensitivity (S), which can improve internal combustion engine performance and efficiency. However, the combustion characteristics of TME have not been comprehensively investigated. Thus, it is essential to study the combustion characteristics of TME and construct a detailed chemical kinetic model to describe its combustion. In this paper, two high-pressure shock tubes and a constant-volume reactor are used to measure ignition delay times and laminar flame speeds of TME oxidation. Further, the ignition delay times were measured at equivalence ratios of 0.5, 1.0, and 2.0 in “air”, at pressures of 5 and 10 bar, in the temperature range of 950 – 1500 K. Flame speeds of the TME/ “air” mixtures were measured at atmospheric pressure, at a temperature of 325 K, for equivalence ratios ranging from 0.78 to 1.31. Two detailed kinetic mechanisms were constructed independently using different methodologies; the KAUST TME mechanism was constructed based on NUIGMech1.1, and the MIT TME mechanism was built using the Reaction Mechanism Generator (RMG). Both mechanisms were used to simulate the experimental results using Chemkin Pro. In the present work, reaction flux and sensitivity analyses were performed using the KAUST mechanism to determine the critical reactions controlling TME oxidation at the conditions studied.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

The intrinsic value of bioblendstocks: Prenol as a case study

Decarbonizing the transportation sector is likely to require both electrification and increased incorporation of biofuels and/or bioblendstocks. While the social and environmental benefits of bioblendstocks are well understood, their real value for the fuel producers has not been established. As such, this work considers prenol as a bioblendstock case study to identify sources of intrinsic value to fuel blenders by studying the properties of binary mixtures with gasoline components. The considered refinery blendstocks were samples of full range naphthas from the distillation, fluidized catalytic cracking, isomerization, alkylation, and reforming units. Octane numbers, Reid vapor pressure, distillation curves, and sulfur content were evaluated. Our results indicate the need for adjusting the formulation of the base fuel, depending on the interplay among the properties of the bioblendstock and those of the base fuel. Prenol increased research octane number (RON) and octane sensitivity (OS) of the base fuel, by up to 25 and 10 octane numbers, respectively. Additionally, 10 vol% prenol reduced RVP up to 2.2 psi, for the more volatile blendstock. Thus, considering prenol as a low volatility, RON/OS boosting bioblendstock, the composition of the preferred base fuel was proposed as containing reduced olefins and aromatics, and increase light fractions. The potential impact of this new gasoline formulation on refining processes and products gives rise to direct sources of value to the refiners, such as exporting products to the chemicals market, increasing the value of intermediate refinery streams, decreasing operating severity of certain refinery units, and broadening of the product suite.

09 BIOMASS FUELS↗
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Fuel property impacts on gaseous and PM emissions from a multi-mode single-cylinder engine

The U.S. Department of Energy’s Co-Optima initiative has focused on improving fuel economy and vehicle performance while reducing emissions through the simultaneous development of emerging sustainable fuels with beneficial properties and advanced combustion strategies. A major thrust has been the development of advanced compression ignition (ACI) combustion strategies of gasoline range fuels in combination with spark-ignited (SI) combustion in a single engine capable of multi-mode operation to achieve high power density with enhanced part load efficiency. The aim of this study was to further the understanding of how emissions from both ACI and SI strategies operating on the same fuels in the same engine are impacted by different fuel properties. This investigation focused on particulate matter (PM) and gaseous hydrocarbon emissions from 6 different fuels across 3 different combustion modes on the same single-cylinder engine designed for multi-mode operation: SI combustion, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). In each of these modes, 3 different CA50 phasings were studied such that all 6 fuels could be studied at the same phasings. Three of the six different fuels used were specially formulated in a previous investigation to study the impact of fuel distillation and aromatic content while maintaining the research octane number (RON) and octane sensitivity. Additionally, neat isooctane and two ethanol containing fuels (RD5-87 and Co-Optima E30) were studied. Different fuel and phasing impacts on emissions were observed across the three combustion modes. Fuel properties were found to impact soot PM and particle number more than the CA50 phasing, while the phasing had more impact on NOx emissions. The NOx emissions were reduced in the PFS mode for all fuels compared to SI combustion, but the SACI combustion mode did not reduce NOx emissions. Although PFS produced low soot PM emissions like SI, total PM mass emissions were significantly higher due to large organic carbon (OC) PM mass contribution. Both PFS and SACI had greater particle number emission than SI operation with small nuclei mode particles dominating in PFS compared to large agglomeration particles in SACI.

42 ENGINEERING↗
DOE OSTI2023

Understanding fundamental effects of biofuel structure on ignition and physical fuel properties

The development of biochemicals and biofuels with advantaged properties of higher combustion efficiency at lower emission levels can be aided by a priori prediction of critical global characteristics based on molecular structure. Existing predictive techniques are incomplete for comprehensive ignition and physical fuel property prediction. Here this investigation focuses on filling this knowledge gap by developing a priori prediction techniques for predicting important ignition as well as physical fuel properties of promising advantaged biofuels. We demonstrate the utility of this a priori prediction technique on saturated (≤C 5 ) alcohols, both linear and branched in nature by correlating their molecular structure with both important ignition and physical properties of the fuels. This work utilizes a semi-automated method of predicting ignition characteristics via accurate fundamental-based calculations of the fuel radical cascades that govern low-temperature combustion. This numerical methodology is supported by the relevant fuel ignition delay time (IDT) and research octane number (RON) data experimentally measured by the Advanced Fuel Ignition Delay Analyzer (AFIDA). Phyiscal fuel property trends are also analyzed by correlating the molecular structure of the fuel to its physical characteristics. Based on their molecular structure, recommendations are made on an a priori method for selecting biofuels that have advantaged properties for the selected fuel application. Lastly, the utility of this investigation is extended beyond the subset of alcohols considered by analyzing the IDT trends of i-Pentanol and n-Hexanol, revealing the fidelity of the novel kinetic modelling approach and the accuracy of the predicted trends in this study.

09 BIOMASS FUELS↗
DOE OSTI2024

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗
DOE OSTI2024

A chemical kinetic analysis of knock propensity of methanol-to-gasoline fuel

Production of low carbon gasoline-like fuels such as methanol-to-gasoline (MTG) is a promising approach to achieve rapid greenhouse gas emission reduction of the transportation sector. Despite the fact that gasoline that meets the ASTM D4814 standard for automotive spark-ignition engine fuel can be readily produced from these processes, it is unclear how the composition of MTG may affect engine performance and emissions. Here, in this paper, a surrogate for an MTG is used to numerically study the effects of gasoline composition on knock propensity and on the sensitivity of knock to thermal and fuel stratification, to oxygen dilution and to nitric oxide from exhaust gas recirculation of residual gases. Simulations were performed in ANSYS CHEMKIN-PRO using a comprehensive chemical kinetic mechanism for gasoline surrogates, and results of the MTG surrogate were compared against those of a petroleum-based regular E10 gasoline, termed PACE-20. A premium-grade MTG fuel was also formulated by adding ethanol to the MTG surrogate, and results were compared against those of four premium-grade, gasoline-like fuels representative of future alternative gasoline formulations. Surrogates and mechanism were evaluated by comparison against experimental engine data, and the model showed high accuracy at stoichiometric conditions (mean absolute error of ignition timing equal to 1.46 crank angle degrees) but larger deviations at lean conditions (mean absolute error of ignition timing equal to 5.52 crank angle degrees). Despite the fact that the MTG surrogate has a RON 1.1 units higher than that of PACE-20, it may show higher knock propensity at medium temperature conditions due to a less intense NTC behavior. MTG autoignition was more temperature- and equivalence ratio-sensitive than that of PACE20, suggesting that MTG can benefit more from naturally-occurring thermal stratification or from induced fuel stratification of the end gas to mitigate knock intensity. The sensitivity of autoignition reactivity to oxygen dilution and to NO concentration was higher for MTG than for regular gasoline at medium loads, but the opposite trend was observed at high loads due to the effect of pressure on the low-temperature chemistry of regular gasoline. Approximately 14 % vol ethanol content was required to upgrade the octane rating of MTG from regular grade to premium grade. Adding 13.6 % vol ethanol made the fuel autoignition less sensitive to both oxygen dilution and NO content (ignition time varies approx. 17 % and 50 % less with oxygen dilution and NO addition, respectively, when adding ethanol at high engine loads).

02 PETROLEUM↗
DOE OSTI2022

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗