Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROCKET THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Some effects of cyclic induced deformation in rocket thrust chambers

A test program to investigate the deformation process observed in the hot gas wall of rocket thrust chambers was conducted using three different liner materials. Five thrust chambers were cycled to failure using hydrogen and oxygen as propellants at a chamber pressure of 4.14 MN/sq m. The deformation was observed nondestructively at midlife points and destructively after failure occurred. The cyclic life results are presented with an accompanying discussion about the types of failure encountered. Data indicating the deformation of the thrust chamber liner as cycles are accumulated are presented for each of the test thrust chambers.

Hannum, N. P.↗
NASA NTRS1961

Performance of Small (100-lb Thrust) Rocket Motors Using Coaxial Injection of Hydrazine and Nitrogen Tetroxide

An investigation was conducted on a small (approximately 100-lb thrust) rocket using coaxial injection of hydrazine and nitrogen tetroxide. Characteristic-velocity efficiencies of 94 percent of the theoretical shifting equilibrium value were obtained at a chamber pressure of about 300 pounds per square inch using a 21-tube injector and a combustion chamber characteristic length of 10 inches. Performance at lower chamber pressures could be improved by reducing contraction ratio and thereby increasing the combustion chamber length and injector pressure drop, which would tend to promote better mixing. Calculations based on experimental data showed a vacuum specific impulse of 305 seconds with a nozzle area ratio of 50.

Wasserbauer, Joseph F.↗
NASA NTRS1962

PYROLYTIC GRAPHITE ROCKET THRUST CHAMBER INVESTIGATION PROJECT. MONTHLY LETTER

This is the Monthly Letter Progress Report for the eighth month of a twelve month technical study directed toward the following objectives: A. Determining analytically and experimentally the feasibility and attractiveness of using free-standing pyrolytic graphite for a radiation cooled liquid rocket thrust chamber and exit nozzle for space application. B. Establishing through analysis and experimental demonstration, a set of design principles to facilitate the design of a reliable pyrolytic graphite thrust chamber assembly for a specific range of operating conditions. C. Demonstrate by means of test firings of complete thrust chamber assemblies, the validity of the design data and principles developed during the program. Preparations have been completed for test firing the two 100 lb. thrust Boron Pyralloy chambers at Marquardt during the first week in March 1962. These two chambers will first be static pressure checked with water to a pressure of 135 psig. The chambers will then be test fired with N204/N2H4-MMH propellants . Test samples of eleven different pyrolytic carbide and nitride materials have been ordered for high temperature oxidation tests and should be delivered by the end of March for evaluation in the plasma torch facility. The specific materials ordered in free- standing condition in thicknesses from 0.030 inch to 0.065 inch were as follows: (a) Pyrolytic graphite (on hand) (b) Pyrolytic graphite-boron alloy (on hand) (c) Pyrolytic graphite-tungsten alloy (d)Boron nitride (e) Titanium nitride (f) Silicon carbide (g) Titanium carbide (h) Zirconium carbide (i) Hafnium carbide (j) Niobium carbide (k) Tantalum carbide (l) High density (1 1-90) graphite (m) High density graphite (heat treated) These materials were ordered from Raytheon, HTM, and American Meta 1 Products . A summary of the available data on the oxidation rates of pyrolytic materials under slow air and rocket motor conditions is shown in Figure 1. High Temperature Materials, Inc. has been contacted relative to providing Pyrographite thrust chambers with extra-thick walls . They believe they can deliver chambers with substantially thicker walls than were possible a short time ago. Such a configuration, with acceptable residual stresses, would provide a longer firing life since it is ultimately limited by the oxidation rate of the chamber wall material. Stress and structural studies have continued. The analytical stress studies point out some of the problems associated with the experimental determination of the elastic constants of this highly anisotropic material. Further analysis may shed light on improved techniques for making these experimental determinations. The large potential weight saving available with the use of pyrolytic graphite as a thrust chamber wall material in a radiation cooled rocket motor has been calculated and is shown graphically in Figure 2. Figure A presents the program progress schedule and the actual expenditures as of 7 February 1962.

ROCKET ENGINE↗
NASA NTRS1955

Injection Principles from Combustion Studies in a 200-Pound-Thrust Rocket Engine Using Liquid Oxygen and Heptane

The importance of atomizing and mixing liquid oxygen and heptane was studied in a 200-pound-thrust rocket engine. Ten injector elements were used with both steel and transparent chambers. Characteristic velocity was measured over a range of mixture ratios. Combustion gas-flow and luminosity patterns within the chamber were obtained by photographic methods. The results show that, for efficient combustion, the propellants should be both atomized and mixed. Heptane atomization controlled the combustion rate to a much larger extent than oxygen atomization. Induced mixing, however, was required to complete combustion in the smallest volume. For stable, high-efficiency combustion and smooth engine starts, mixing after atomization was most promising.

Heidmann, M. F.↗
NASA NTRS1985

Small centrifugal pumps for low thrust rockets

This paper presents the results of a combined analytical and experimental investigation of low specific speed pumps for potential use as components of propellant feed systems for low thrust rocket engines. Shrouded impellers and open face impellers were tested in volute type and vaned diffuser type pumps. Full- and partial-emission diffusers and full- and partial-admission impellers were tested. Axial and radial loads, head and efficiency versus flow, and cavitation tests were conducted. Predicted performance of two pumps are compared when pumping water and liquid hydrogen. Detailed pressure loss and parasitic power values are presented for two pump configurations. Partial-emission diffusers were found to permit use of larger impeller and diffuser passages with a minimal performance penalty. Normal manufacturing tolerances were found to result in substantial power requirement variation with only a small pressure rise change. Impeller wear ring leakage was found to reduce pump pressure rise to an increasing degree as the pump flowrate was decreased.

Gulbrandsen, N. C.↗
NASA NTRS1990

Cooling of rocket thrust chambers with liquid oxygen

Rocket engines using high pressure liquid oxygen (LOX) and kerosene (RP-1) as the propellants have been considered for future launch vehicle propulsion. Generaly, in regeneratively cooled engines, thefuel is used to cool the combustion chamber. However, hydrocarbons such as RP-1 are limited in their cooling capability at high temperatures and pressures. Therefore, LOX is being considered as an alternative coolant. However, there has been concern as to the effect on the integrity of the chamber liner if oxygen leaks into the combustion zone through fatigue cracks that may develop between the cooling passages and the hot-gas side wall. To address this concern, an investigation was previously conducted with simulated fatigue cracks upstream of the thrust chamber throat. When these chambers were tested, an unexpected melting in the throat region developed which was not in line with the simulated fatigue cracks. The current experimental program was conducted in order to determine the cause for the failure in the earlier thrust chambers and to further investigate the effects of cracks in the thrust chamber liner upstream of the throat. The thrust chambers were tested at oxygen-to-fuel mixture ratios from 1.5 to 2.86 at a nominal chamber pressure of 8.6 MPa. As a result of the test series, the reason for the failure occurring in the earlier work was determined to be injector anomalies. The LOX leaking through the simulated fatigue cracks did not affect the integrity of the chambers.

Armstrong, Elizabeth S.↗
NASA NTRS1990

Cooling of rocket thrust chambers with liquid oxygen

Rocket engines using high pressure liquid oxygen (LOX) and kerosene (RP-1) as the propellants have been considered for future launch vehicle propulsion. Generally, in regeneratively cooled engines, the fuel is used to cool the combustion chamber. However, hydrocarbons such as RP-1 are limited in their cooling capability at high temperatures and pressures. Therefore, LOX is being considered as an alternative coolant. However, there has been concern as to the effect on the integrity of the chamber liner if oxygen leaks into the combustion zone through fatigue cracks that may develop between the cooling passages and the hot-gas side wall. To address this concern, an investigation was previously conducted with simulated fatigue cracks upstream of the thrust chamber throat. When these chambers were tested, an unexpected melting in the throat region developed which was not in line with the simulated fatigue cracks. The current experimental program was conducted in order to determine the cause for the failure in the earlier thrust chambers and to further investigate the effects of cracks in the thrust chamber liner upstream of the throat. The thrust chambers were tested at oxygen-to-fuel mixture ratios from 1.5 to 2.86 at a nominal chamber pressure of 8.6 MPa. As a result of the test series, the reason for the failure occurring in the earlier work was determined to be injector anomalies. The LOX leaking through the simulated fatigue cracks did not affect the integrity of the chambers.

Armstrong, Elizabeth S.↗
NASA NTRS1958

Static Investigation of Paddle Vane Oscillating in Jet of 1,300-Pound-Thrust Rocket Motor

The results of a static investigation conducted to measure the normal forces on the entire jet-vane assembly and the hinge moments on the jet vane produced by a paddle vane oscillating in the jet of a 1,500-pound-thrust rocket motor are presented for vane-deflection angles from -5 deg to 25 deg. A maximum average normal force of 71 pounds with a corresponding value for maximum average hinge moment of 228 inch-pounds was obtained with the maximum area of jet vane immersed at a jet-vane angle of 25 deg decrease in thrust caused by immersion of the jet vane varied from a maximum loss of about 58 pounds, or approximately 5 percent at maximum jet-vane angle of 25 deg, to zero loss at jet-vane angles less than approximately 10 deg.

Lanford, Wade E.↗
NASA NTRS1991

Examination of various turbulence models for application in liquid rocket thrust chambers

There is a large variety of turbulence models available. These models include direct numerical simulation, large eddy simulation, Reynolds stress/flux model, zero equation model, one equation model, two equation k-epsilon model, multiple-scale model, etc. Each turbulence model contains different physical assumptions and requirements. The natures of turbulence are randomness, irregularity, diffusivity and dissipation. The capabilities of the turbulence models, including physical strength, weakness, limitations, as well as numerical and computational considerations, are reviewed. Recommendations are made for the potential application of a turbulence model in thrust chamber and performance prediction programs. The full Reynolds stress model is recommended. In a workshop, specifically called for the assessment of turbulence models for applications in liquid rocket thrust chambers, most of the experts present were also in favor of the recommendation of the Reynolds stress model.

Hung, R. J.↗
NASA NTRS1979

Performance of a transpiration-regenerative cooled rocket thrust chamber

The analysis, design, fabrication, and testing of a liquid rocket engine thrust chamber which is gas transpiration cooled in the high heat flux convergent portion of the chamber and water jacket cooled (simulated regenerative) in the barrel and divergent sections of the chamber are described. The engine burns LOX-hydrogen propellants at a chamber pressure of 600 psia. Various transpiration coolant flow rates were tested with resultant local hot gas wall temperatures in the 800 F to 1400 F range. The feasibility of transpiration cooling with hydrogen and helium, and the use of photo-etched copper platelets for heat transfer and coolant metering was successfully demonstrated.

Valler, H. W.↗
NASA NTRS1971

Heat pipe technology for advanced rocket thrust chambers

The application of heat pipe technology to the design of rocket engine thrust chambers is discussed. Subjects presented are: (1) evaporator wick development, (2) specific heat pipe designs and test results, (3) injector design, fabrication, and cold flow testing, and (4) preliminary thrust chamber design.

Rousar, D. C.↗
NASA NTRS2010

Performance and Stability Analyses of Rocket Thrust Chambers with Oxygen/Methane Propellants

Liquid rocket engines using oxygen and methane propellants are being considered by the National Aeronautics and Space Administration (NASA) for future in-space vehicles. This propellant combination has not been previously used in flight-qualified engine systems developed by NASA, so limited test data and analysis results are available at this stage of early development. As part of activities for the Propulsion and Cryogenic Advanced Development (PCAD) project funded under the Exploration Technology Development Program, the NASA Marshall Space Flight Center (MSFC) has been evaluating capability to model combustion performance and stability for oxygen and methane propellants. This activity has been proceeding for about two years and this paper is a summary of results to date. Hot-fire test results of oxygen/methane propellant rocket engine combustion devices for the modeling investigations have come from several sources, including multi-element injector tests with gaseous methane from the 1980s, single element tests with gaseous methane funded through the Constellation University Institutes Program, and multi-element injector tests with both gaseous and liquid methane conducted at the NASA MSFC funded by PCAD. For the latter, test results of both impinging and coaxial element injectors using liquid oxygen and liquid methane propellants are included. Configurations were modeled with two one-dimensional liquid rocket combustion analysis codes, the Rocket Combustor Interactive Design and Analysis code and the Coaxial Injector Combustion Model. Special effort was focused on how these codes can be used to model combustion and performance with oxygen/methane propellants a priori, and what anchoring or calibrating features need to be applied, improved or developed in the future. Low frequency combustion instability (chug) occurred, with frequencies ranging from 150 to 250 Hz, with several multi-element injectors with liquid/liquid propellants, and was modeled using techniques from Wenzel and Szuch. High-frequency combustion instability also occurred at the first tangential (1T) mode, at about 4500 Hz, with several multi-element injectors with liquid/liquid propellants. Analyses of the transverse mode instability were conducted by evaluating injector resonances and empirical methods developed by Hewitt.

Hulka, James R.↗
NASA NTRS1990

New method of making advanced tube-bundle rocket thrust chambers

An improved method of fabrication rocket chambers for future space applications is described. Included are fabrication demonstrator and test chambers produced by this method. This concept offers the promise of improved cyclic life, reusability, and performance. The performance is improved because of the enhanced enthalpy extraction. The improved cyclic life, reusability, and reliability is improved because of the structural compliance inherent in the construction. The method of construction involves the forming of the combustion chamber by a tube-bundle of high conductivity copper or copper alloy tubes and the bonding of these tubes by a unique electroforming operation. Furthermore, the method of fabrication reduces chamber complexity by incorporating manifolds, and structural stiffeners while having the potential for thrust chamber cost and weight reduction.

Kazaroff, John M.↗
NASA NTRS1992

A numerical model for coupling between atomization and spray dynamics in liquid rocket thrust chambers

This paper describes a novel method of coupling the atomization and spray combustion processes encountered in coaxial injection elements of liquid rocket engine thrust chambers. This method is based on the Jet-Embedding technique in which the liquid jet core equations and the gas phase equations are solved separately. The liquid and gas phase solutions, however, are coupled through the boundary conditions at the interface between the phases. The computational grid for the gas phase calculations are adapted to the shape of the liquid jet core. The axial variation of droplet sizes are calculated using a stability analysis appropriate for the atomization regime of liquid jet breakup. The predictions of this method have been validated with experimental data on low speed water jets. Using this method, calculations are performed for the SSME fuel preburner single injector flow field. The results obtained are in good agreement with the predictions of the volume-of-fluid method.

Giridharan, M. G.↗
NASA NTRS2000

Development of an Integrated Rocket Thrust Chamber Assembly Analysis and Design Toolkit (TCAT)

There are many individual computational tools and methods used to analyze and design components of a rocket engine thrust chamber assembly (TCA) 11,21. To analyze and design a thrust chamber assembly these tools are usually used in sequence while communication of information between these tools is usually done manually. Each component of a TCA is usually designed and optimized individually with limited considerations on system optimized design. This approach is often iterative and can be prone to error. Also at present, expert knowledge of each tool is required. The objective of this software development effort is to select, integrate and automate the best tools into an easy-to-use computational package, the Thrust Chamber Analysis Toolkit (TCAT). This tool will provide a seamless process to analyze and design all or individual components of a thrust chamber assembly. This paper describes the current status of the MAT software development. The selected component codes and their capabilities are briefly described. User and module interfaces and integration status are presented. MAT pre- and post-processing added options are presented and overall MAT capabilities are demonstrated with the results of sample cases. Ongoing and planned model validation efforts are also described. Finally, the MAT future plan options are discussed.

Farhangi, S.↗
NASA NTRS1974

Fabrication of liquid-rocket thrust chambers by electroforming

Electroforming has proven to be an excellent fabrication method for building liquid rocket regeneratively cooled thrust chambers. NASA sponsored technology programs have investigated both common and advanced methods. Using common procedures, several cooled spool pieces and thrust chambers have been made and successfully tested. The designs were made possible through the versatility of the electroforming procedure, which is not limited to simple geometric shapes. An advanced method of electroforming was used to produce a wire-wrapped, composite, pressure-loaded electroformed structure, which greatly increased the strength of the structure while still retaining the advantages of electroforming.

Duscha, R. A.↗