Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Transducer Resolution Effect on Pressure Fluctuations Beneath Hypersonic Turbulent Boundary Layers

The size of a pressure transducer is known to affect the accuracy of measurements of wall-pressure fluctuations beneath a turbulent boundary layer because of spatial averaging over the sensing area of the transducer. In this paper, the effect of finite transducer size is investigated by applying spatial averaging or wavenumber filters to a database of hypersonic wall pressure generated from a direct numerical simulation (DNS) that simulates the turbulent portion of the boundary layer over a sharp 7° half-angle cone at nominally Mach 8. Here, a good comparison between the DNS and the experiment in the Sandia Hypersonic Wind Tunnel at Mach 8 is achieved after spatial averaging is applied to the DNS data over an area similar to the sensing area of the transducer. The study shows that a finite sensor size similar to that of the PCB132 transducer can cause significant attenuation in the root-mean-square and power spectral density (PSD) of wall-pressure fluctuations, and the attenuation effect is identical between cone and flat plate configurations at the same friction Reynolds number. The Corcos theory is found to successfully compensate for the attenuated high-frequency components of the wall-pressure PSD.

42 ENGINEERING↗
DOE OSTI2023

Effect of pressure on high-temperature oxidation of Ni alloys in supercritical CO 2 containing impurities

Direct supercritical CO 2 (sCO 2 ) power cycles require structural materials compatible with hot sCO 2 containing high levels of water and oxygen impurities. Chromia-forming Ni-based superalloys, which are leading candidates at temperatures > 600 °C, have shown good compatibility in pure sCO 2 , however potential impurity effects are not well understood. In this report we exposed several commercial Ni-based alloys to 95%CO 2 -4%H 2 O-(1-3)%O 2 at 750 °C and 0.1 or 20 MPa for 2500 h. Protective chromia scales formed in all cases. Nevertheless, water vapor-assisted oxide volatilization clearly occurred at high pressure. The volatilization rates decreased with time, but still represent a potentially serious compatibility issue in real, high-velocity, sCO 2 systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A control-oriented combustion model framework for compression ignition engines operating on low-reactivity fuel

This work focuses on zero-dimensional modeling of the heat release rate in a compression ignition engine operating on gasoline-like fuels. Due to the properties of gasoline, such as high volatility and longer ignition delay than diesel, the injection strategies can vary significantly from the operation with conventional diesel fuel. Different injection strategies are commonly used to achieve varying degrees of in-cylinder stratification in order to shape the combustion event and maximize efficiency. The proposed zero-dimensional combustion model was developed to account for the different stages in combustion caused by the fuel stratification. As the ignition delay model is an integral part of the entire combustion process and significantly affects the prediction accuracy, special attention has been paid to local phenomena influencing ignition delay. A one-dimensional spray model by Musculus and Kattke was employed in conjunction with a Lagrangian tracking approach in order to estimate the local air–fuel ratio within the spray tip, as a proxy for reactivity. The local air–fuel ratio, in-cylinder temperature and pressure were used in an integral fashion to estimate the ignition delay. Heat release rates were modeled using first-order non-linear differential equations. The proposed combustion model was validated against experimental data of a heavy-duty compression ignition engine with up to three injection events at mostly 1038 r/min and 14 bar brake mean effective pressure. Further validation of the model was carried out at other engine loads and speeds. Model prediction errors in CA50 of less than 1 °CA across all conditions were found. Modeling results of other combustion metrics such as combustion duration and indicated mean effective pressure are also highly satisfactory. In addition, the model has been shown to be capable of estimating the ringing intensity for most conditions.

Pamminger, Michael↗
DOE OSTI2026

Fragile-to-strong transition in liquid As 2 S 3 under pressure: The effect of melt metallization

The well-known classification of glass-forming melts into fragile and strong liquids has several notable exceptions, including water, silica, and certain phase-change materials (PCMs). These exceptional fluid systems exhibit a fragile-to-strong transition (FST) upon cooling: a transformation from a high-temperature liquid with fast atomic dynamics, low viscosity, and low flow activation energy, to a viscous supercooled melt with high energy barriers near the glass transition temperature T g . This behavior is critically important for non-volatile memories, photonic tensor cores, reconfigurable metamaterials, and other devices, that use PCMs, enabling nanosecond-scale crystallization in the fragile regime and long data retention in the strong regime near or below T g . A significant structural transformation is expected between these two viscosity regimes, along with a semiconductor-metal (SC-M) transition upon heating, driven by high internal pressure and associated density increase. By applying high external pressure to the canonical low-conducting chalcogenide melt As 2 S 3 , we observed both the FST and the SC-M transition, occurring simultaneously within the same domain of the P, T−phase space. These findings suggest that the FST is not limited to a few exceptional liquids but is a common phenomenon, at least in systems that exhibit melt metallization within specific regions of their P, T−phase diagrams.

first-principles molecular dynamics↗
DOE OSTI2021

Impact of low reactivity fuel type on low load combustion, emissions, and cyclic variations of diesel-ignited dual fuel combustion

In this study, cyclic variations in dual fuel combustion with diesel ignition of three different low reactivity fuels (methane, propane, and gasoline) are examined under identical operating conditions. Experiments were performed on a single cylinder research engine (SCRE) at a low load of 3.3 bar brake mean effective pressure (BMEP). The start of injection (SOI) of diesel was varied from 280 to 330 absolute crank angle degrees (CAD). Engine speed, rail pressure, and boost pressure were held constant at 1500 rpm, 500 bar, and 1.5 bar, respectively. The energy substituted by the low reactivity fuel was fixed at 80% of the total energy input. It was found that diesel-methane (DM) and diesel-propane (DP) combustion were affected by diesel mixing to a greater extent than diesel-gasoline (DG) combustion due to the higher reactivity of gasoline. The magnitude of low temperature heat release was greatest for DG combustion followed by DM and DP combustion for all SOIs. The ignition delay for DG combustion was the shortest, followed by DM and DP combustion. DM and DP combustion exhibited more cyclic variations than DG combustion. Cyclic variations decreased for DM and DP combustion when SOI was advanced; however, DG combustion cyclic variations remained essentially constant for all SOIs. Earlier SOIs (280, 290, 300, and 310 CAD) for DM and (280, 290, and 300 CAD) for DP combustion indicated some prior-cycle effects on the combustion and IMEP (i.e. some level of determinism).

Engineering↗
DOE OSTI2020

Pressure-temperature effects on knock with iso-octane and propane at various compression ratios and intake temperatures

Knock remains one of the main limitations for increased internal combustion engine efficiency. Recent trends in light-duty vehicles towards downsized, boosted engines increases the need for improving the understanding between fuel chemistry and thermodynamic effects contributing to knock. Previous studies have shown the importance of end-gas thermodynamic conditions on knock onset and behavior, with relationships to fuel chemistry illustrated. However, a complete understanding of how fuels allow access to higher engine loads and the governing physics behind end-gas knock under a wide range of thermodynamic conditions is still unclear. Experiments in this work improve this understanding with the use of three fuels (1) iso-octane, a low octane sensitivity (OS) fuel (2) a Co-Optima aromatic core fuel, which has similar research octane number (RON) yet significantly higher OS, and (3) propane, known for its knock resistance. Engine load sweeps are conducted with each fuel while maintaining a CA50 of 8 crank angle degrees after top dead center (°CA aTDCf). As load increases and knock onset is observed, spark is delayed to its knock limited spark advance (KLSA) allowing further increases in load until either one of two limits is reached; (1) CA50 retard limit (2) Peak cylinder pressure limit. Experiments are conducted at 40°C and 90°C intake temperature and at two distinct compression ratios (rc) 9.2:1 and 13.6:1. Two-zone zero-dimensional simulations were performed in Chemkin to extract end-gas pressure and temperature conditions through the combustion process for each experimental condition of interest. CA50 response as a function of engine load is compared for all experimental conditions and fuels, and a pressure-temperature (PT) trajectory analysis is conducted using constant volume ignition delay contours to explain the behavior of each fuel.

Dal Forno Chuahy, Flavio↗
DOE OSTI2022

Development of a medium-duty stoichiometric diesel micro-pilot natural gas engine

Fueling a compression-ignition engine with premixed natural gas offers the potential to combine a clean-burning, low-carbon fuel with a high compression ratio, high-efficiency engine. This work describes the development of a multi-cylinder 6.7 L diesel engine converted to run stoichiometric diesel micro-pilot/ natural gas premix combustion with a maximum diesel contribution target of 5% of the total fuel energy and a three-way catalyst aftertreatment system. Results are given by comparing the stoichiometric combustion to the diesel baseline operation, showing combustion characteristics differences, including the rapid two stage heat release. A high load output of 23 bar brake mean effective pressure was obtained with diesel-like brake thermal efficiency of 41%. This operating condition enabled a brake specific CO 2 emissions reduction of up to 25% when compared to diesel. It was observed that the low load output is limited by combustion stability when operated at stoichiometric condition. The three-way catalyst is observed to run at peak efficiency with an equivalence ratio of 1.01. Injector fouling was observed through the inspection of the nozzle and its internal parts, indicating carbon build-up similar to that seen in injector coking mechanisms. A comparison of the developed engine to other engine technologies is given, showing that the diesel micro-pilot natural gas engine performance is in good standing among other diesel and gas engines in the market.

Engineering↗
DOE OSTI2021

Effect of Pressure and Temperature on Carbon Dioxide Reduction at a Plasmonically Active Silver Cathode

Here, carbon dioxide reduction at a plasmonically active silver cathode was investigated by varying the pressure and temperature at multiple applied potentials under both dark and illuminated conditions to understand the mechanism of selectivity changes driven by plasmon-enhanced electrochemical conversion. Carbon dioxide partial pressures (P Co 2 ) from 0.2 to 1 atm were studied during linear sweep voltammetry and chronoamperometry at -0.7, -0.9, and -1.1 V RHE . At a given applied overpotential the total current density increased with increasing P Co 2 in both the dark and the light, but there were significant differences in the Tafel behavior between dark and illuminated conditions. The reduction of CO 2 to carbon monoxide (CO) was found to have first-order behavior with respect to P Co 2 at all applied potentials in both the dark and the light, likely indicating no change in the rate-determining step upon illumination. Activity for the hydrogen (H 2 ) evolution reaction decreased with increasing P Co 2 at slightly different rates in the dark and the light at each applied potential, making it unclear if light is influencing CO or H 2 intermediate adsorbate coverage. Both formate and methanol production showed no dependence on P Co 2 under any conditions, but the true reaction orders may be masked by the much higher activity for CO and H 2 at the silver cathode. The investigation of product distribution with temperature at 14, 22, and 32°C at -0.7, -0.9, and -1.1 V RHE in both the dark and the light demonstrated that the selectivity changes observed upon illumination are not caused by local heating of the cathode surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Quantifying the effects of pressure management for the Williston basin Brine Extraction and Storage Test (BEST) site using machine learning

Active reservoir management (ARM) through brine extraction can reduce pressure buildup during large-scale implementation of carbon capture and storage (CCS) projects. This study used machine learning (ML)-assisted approaches to analyze bottomhole pressure (BHP) responses to various brine injection and extraction scenarios. Field monitoring data were collected over a 2-year operation period at two injection wells and one extraction well (about 400 meters away) as part of a Brine Extraction and Storage Test (BEST) in the North Dakota portion of the Williston Basin. Injection activities increased the BHPs at the injection wells by around 0.70 MPa (~100 psi) during the operation period. Extraction activities demonstrated the capability to decrease the BHPs at the injection wells by approximately 0.21–0.34 MPa (30–50 psi) depending on the ratio of the extraction and injection well flow rates (the “extraction ratio” – a normalization procedure used in the analysis). The pressure reduction provided by the extraction well equated to 30%–50% of the pressure buildup at the injection well. Furthermore, this work shows how ML analytics can play a key role in estimating reservoir pressure responses for complex injection and extraction activities during pressure management practices of CCS projects.

58 GEOSCIENCES↗
DOE OSTI2024

Effect of Pressure on Crystal Structure and Phonon Density of States of FeSi

The strongly correlated material FeSi displays several unusual thermal, magnetic, and structural properties under varying pressure-temperature (P-T) conditions. It is a potential thermoelectric alloy and a material with several geochemical implications as a possible constituent at the Earth's core-mantle boundary (CMB). Previous theoretical studies predicted a pressure-induced B20-B2 transition at ambient temperature below 40 GPa; however, experimentally, the structural transition is observed only at high P-T conditions. In this study, we have performed high-pressure powder X-ray diffraction (XRD) up to 90 GPa and Nuclear Resonant Inelastic X-ray Scattering (NRIXS) measurements up to 120 GPa to understand the phase stability and lattice dynamics. Our study provides evidence for a non-hydrostatic stress-induced B20-B2 transition in FeSi at around 36 GPa. We deduced the Fe partial phonon density of states (PDOS) and thermal parameters from NRIXS measurements up to 120 GPa and compared them with density functional theory (DFT) calculations. Furthermore, the computations show pressure-induced metallization and the band gap closing around 12 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effect of pressure cycling and compression rate on the bcc-hcp transition in an FeNi alloy

Here, we investigate the body-centered cubic (bcc) to hexagonal close-packed (hcp) phase transition in Fe-10wt. %Ni alloy, combining pressure cycling and fast compression with time-resolved synchrotron x-ray diffraction in a dynamic diamond anvil cell. Three pressure cycles were conducted with compression rates ranging from 0.1 to nearly 10 3 GPa/s. During the first cycle with the slowest compression, the observed orientations in the bcc and hcp phases are consistent with the Burgers mechanism, followed by c-axis rotation of the hcp phase consistent with {$10$ $\bar{1}2$} twinning. During the following cycles with fast compression at 10 2 –10 3 GPa/s, the hcp phase exhibits negligible c-axis rotation with a nearly constant c/a ratio of ∼1.61 up to ∼30 GPa, indicating suppression of plastic deformation (especially, twinning) due to sample confinement from the gasket. Notably, the onset pressure of the transition decreases with additional pressure cycling and faster compression, which normally leads to over-pressurization. This suggests that defects or shear induced from the pressure cycling reduces the transition kinetics even during fast compression. These insights into the deformation and transition behavior in an FeNi alloy under multiple dynamic loading cycles can offer guidance for future design of advanced structural alloys and improve our understanding of planetary core processes.

FeNi alloy↗
DOE OSTI2021

The Effect of Pressure on NO x Entitlement and Reaction Timescales in a Premixed Axial Jet-In-Crossflow

This paper investigates the pressure dependency of a lean premixed jet injected into a lean vitiated crossflow with an experimentally verified detailed chemistry computational fluid dynamics (CFD) model and 53 species considered. Experimental data were taken in an axially staged combustor with an optically accessible test section, allowing the use of particle image velocimetry (PIV) and CH* chemiluminescence techniques as well as point measurement of species concentration, temperature, and pressure. The experimental data cases at one, three, and five atmospheres were selected to describe the flame stabilization dependency on pressure and gain the required knowledge for an extrapolation to engine condition. Simulated exit nitrogen oxide levels were validated with experimental emission data, and a global emission trend for the NO reduction at elevated pressure and constant turbine inlet temperature level was defined. The nitrogen oxide benefit at elevated operating pressure was justified with the significantly smaller flame surface area: the analysis of the simulated spanwise and top-view profiles showed a relatively short receded core flame with nitrogen oxide production in the center at high pressure relative to a longer and larger shear layer flame at atmospheric condition that produced NO toward the inner and outer side of the flame. Furthermore, decomposition of the Damköhler number revealed the strong influence of the reaction timescales with higher reaction rates at elevated pressure, along with a moderate influence of the turbulent timescales, showing higher turbulence intensity in the lee-side recirculation zone at lower pressure.

03 NATURAL GAS↗