SEARCH · Engineering Papers

Results for “Photocurrent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Impact of superlattice size on quantum efficiency and polarization in MOCVD-grown strained GaAs/GaAsP photocathodes

Strained superlattice GaAs photocathodes are crucial for providing high photocurrent beams of spin-polarized electrons at several accelerator facilities including the Continuous Electron Beam Accelerator Facility at Thomas Jefferson National Accelerator Facility and the future Electron–Ion Collider at Brookhaven National Laboratory. Here, in this work, we study the effects of varying the number of superlattice pairs on the polarization and photocurrent of the photocathodes. We observe a saturation in quantum efficiency beyond 30 pairs, with additional layers yielding minimal photocurrent improvement while noticeably reducing the polarization of the beam.

Chemical vapor deposition↗

NASA NTRS1983

A review and summary of cell and module mismatch losses from theoretical and experimental studies

Studies on power loss due to photovoltaic (PV) cell and module parameter mismatch were reviewed. The losses result from the current voltage (I-V) characteristics of cells which vary over a manufactured lot. The peak power and the peak power I-V point vary from cell to cell. The largest parameter variation occurs in the cell photocurrent generation and the most significant loss occurs in series connections since all cells are essentially limited by the lowest photocurrent. Most theoretical studies address only photocurrent variation effects, which consider shunt and series resistance, ideality factor and saturation current to be comparatively insignificant. One study is identified which specifically configured the study of mismatch loss effects. Experimental results consist of estimates based on limited data not taken from specially configured tests.

Lambarski, T. J.↗

NASA NTRS1990

Resonant tunneling IR detectors

Researchers propose a novel semiconductor heterojunction photodetector which would have a very low dark current and would be voltage tunable. A schematic diagram of the device and its band structure are shown. The two crucial components of the device are a cathode (InGaAs) whose condition band edge is below the conduction band edge of the quantum wells and a resonant tunneling filter (GaAs-AlGaAs). In a standard resonant tunneling device the electrodes are made of the same material as the quantum wells, and this device becomes highly conducting when the quantum levels in the wells are aligned with the Fermi level in the negatively biased electrode. In contrast, the researchers device is essentially non-conducting under the same bias conditions. This is because the Fermi Level of the cathode (InGaAs) is still well below the quantum levels so that no resonant transport occurs and the barriers (AlGaAs) effectively block current flow through the device. However, if light with the same photon energy as the conduction-band discontinuity between the cathode and the quantum wells, E sub c3-E sub c1, is shone on the sample, free carriers will be excited to an energy corresponding to the lowest quantum level in the well closest to the cathode (hv plue E sub c1 = E sub o). These electrons will resonantly tunnel through the quantum wells and be collected as a photocurrent in the anode (GaAs). To improve the quantum efficiency, the cathode (InGaAs) should be very heavily doped and capped with a highly reflective metal ohmic contact. The thickness of the device should be tailored to optimize thin film interference effects and afford the maximum absorption of light. Because the device relies on resonant tunneling, its response should be very fast, and the small voltages needed to change the responsivity should allow for very high frequency modulation of the photocurrent. In addition, the device is tuned to a specific photon energy so that it can be designed to detect a fairly narrow range of wavelengths. This selectivity is important for reducing the photocurrent due to spurious light sources.

Woodall, Jerry M.↗

NASA NTRS1991

Temperature dependence of the transient photoconductive response in stretched trans-polyacetylene films with below-gap excitation

The temperature dependence of the picosecond photocurrent with below-gap excitation (1.06 microns) has been measured for a highly oriented form of transpolyacetylene. The one-dimensional picosecond photocurrent is independent of temperature. The three-dimensional picosecond photocurrent is temperature dependent with an activation energy of 63 meV. These results demonstrate the photoproduction of nonlinear charged carriers (solitons and polarons) at energies that are below the principal interband absorption edge.

Walser, A. D.↗

NASA NTRS2011

Sub-Shot Noise Power Source for Microelectronics

Low-current, high-impedance microelectronic devices can be affected by electric current shot noise more than they are affected by Nyquist noise, even at room temperature. An approach to implementing a sub-shot noise current source for powering such devices is based on direct conversion of amplitude-squeezed light to photocurrent. The phenomenon of optical squeezing allows for the optical measurements below the fundamental shot noise limit, which would be impossible in the domain of classical optics. This becomes possible by affecting the statistical properties of photons in an optical mode, which can be considered as a case of information encoding. Once encoded, the information describing the photon (or any other elementary excitations) statistics can be also transmitted. In fact, it is such information transduction from optics to an electronics circuit, via photoelectric effect, that has allowed the observation of the optical squeezing. It is very difficult, if not technically impossible, to directly measure the statistical distribution of optical photons except at extremely low light level. The photoelectric current, on the other hand, can be easily analyzed using RF spectrum analyzers. Once it was observed that the photocurrent noise generated by a tested light source in question is below the shot noise limit (e.g. produced by a coherent light beam), it was concluded that the light source in question possess the property of amplitude squeezing. The main novelty of this technology is to turn this well-known information transduction approach around. Instead of studying the statistical property of an optical mode by measuring the photoelectron statistics, an amplitude-squeezed light source and a high-efficiency linear photodiode are used to generate photocurrent with sub-Poissonian electron statistics. By powering microelectronic devices with this current source, their performance can be improved, especially their noise parameters. Therefore, a room-temperature sub-shot noise current source can be built that will be beneficial for a very broad range of low-power, low-noise electronic instruments and applications, both cryogenic and room-temperature. Taking advantage of recent demonstrations of the squeezed light sources based on optical micro-disks, this sub-shot noise current source can be made compatible with the size/power requirements specific of the electronic devices it will support.

Strekalov, Dmitry V.↗

DOE OSTI2025

Efficient Broadband Terahertz Generation by Above‐Band‐Gap Excitation of the Pyroelectric ZnSnN 2

Terahertz (THz) radiation is a powerful probe of low-energy excitations in all phases of matter. However, it remains a challenge to find materials that efficiently generate THz radiation in a broad range of frequencies following optical excitation. Here, we investigate a pyroelectric material, ZnSnN 2 , and find that its above-band-gap excitation results in the efficient formation of an ultrafast photocurrent generating THz radiation. The resulting THz electric field spans a frequency range from below 1 THz to above 30 THz. The results suggest that the photocurrent is primarily driven by an ultrafast pyroelectric effect where the photo-excited carriers screen the spontaneous electric polarization of ZnSnN 2 . Strong structural disorder reduces the photocarrier lifetime significantly and, thus, enables broadband operation. ZnSnN2 shows a similar THz-emitter performance as the best spintronic THz emitters regarding bandwidth and amplitude. The study unveils the large potential of pyroelectric materials as efficient and broadband THz emitters with built-in bias fields.

36 MATERIALS SCIENCE↗

DOE OSTI2024

In Situ Exploration of Dipole Field Effects on Weak Hysteresis in 3D/2D Perovskites

This research delves into the effects of 2D layers on the functionality of 3D perovskite using lock-in amplifier-based in situ surface photovoltage (SPV) and its phase spectroscopy, with an emphasis on elucidating the connection between the tuning of dipole moments and the photocurrent hysteresis. Conventionally, the SPV of a perovskite/hole transport layer is observed to diminish as positive bias escalates. However, this trend is reversed in the case of 3D perovskite samples, where an augmentation in SPV is noted under positive bias. Notably, 3D/2D perovskite structures initially show a decrease, then an increase in SPV as bias intensifies, a phenomenon more pronounced with larger dipole moments in 2D. However, there is no linear relationship between the dipole moment and the hysteresis factor. Furthermore, using in situ light-chopping-frequency-modulated SPV and Kelvin Probe Force Microscopy, it is revealed that the dipole fields of 2D layers can hinder ion migration. This leads to efficient hole transfer and minimal photocurrent hysteresis in 3D/2D perovskites, providing strong evidence for the underlying cause of hysteresis. Additionally, these findings suggest intricate interplays among the external electric field, interface dipole moments, and surface photovoltaics, offering significant insights into perovskite optoelectronics.

3D/2D perovskite↗

DOE OSTI2025

Photoabsorption and Stability in Triple-Cation Perovskites Influenced by Interfacial Engineering of the Collector

Charge carrier dynamics in three-dimensional (3D) perovskites is critical to understand for enhancing device performance since the photoabsorption mechanism in perovskites influences key functional devices such as photodetectors and solar cells. Temperature-dependent optoelectronic transport measurements were conducted on our triple cation formulation for the first time from 4 K to 300 K to investigate the role of an interfacial Ti underlayer, beneath the conventional Au collector electrode. The photocurrent was 10X larger with the use of a Ti interfacial layer compared to only Au, where device measurements were made using a broadband white light source at room temperature. As temperature increased from 4 K, the photocurrent increased in both cases, consistent with the semiconducting nature of the triple-cation absorber. Besides computing the responsivity as a function of power and temperature, time-domain measurements with ON/OFF pulses of incident white light, showed the switching time constants to be in the tens to few hundred milliseconds range, and largely temperature-invariant for the two contacts examined. Finally, we constructed solar cells with the same triple cation absorber, in an n-i-p architecture with a Spiro-OMeTAD hole transport layer, but the collector was composed of both types of contacts. Exposing our devices to moisture-rich conditions of up to 70% relative humidity showed the Au/Ti contacted devices to be more robust. Here, our experimental results demonstrate that the addition of a Ti interlayer improves collector efficiency through the photoabsorption process while also potentially stabilizing the solar cells, compared to the bare Au, in moisture-rich environments

optoelectronics↗

DOE OSTI2024

Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Atomic layer deposited (ALD) “leaky” TiO 2 have gained interest as charge-selective protection layers for semiconductor solar fuel electrodes. Here we demonstrate the use of sputter-deposited TiO 2 layers as hole selective contacts for WO 3 /CuWO 4 type 2 heterojunction water oxidation photoanodes for the first time. TiO 2 protection layers with varying thicknesses (2 to 128 nm) were deposited using the RF magnetron sputtering technique. The resulting TiO 2 films are amorphous based on Raman spectroscopy and powder XRD. Photoelectrochemical scans and Vibrating Kelvin probe photovoltage spectroscopy show that 2-8 nm TiO 2 layers nearly double the photocurrent to 0.97 mA cm -2 under AM 1.5 illumination (19% AQE at 350 nm), increase the surface photovoltage signal by 25%, and increase the WO 3 /CuWO 4 bandgap. These effects can be attributed to the selectivity of TiO 2 for photoholes. Additionally, SPV data suggest that TiO 2 overlayers suppress copper-based surface recombination defects. Reduced photocurrent and the photovoltage are seen in thicker TiO 2 films (16 to 128 nm) as a result of an increasing hole transfer resistance and because of light shading effects according to photoaction spectra. The TiO 2 films also improve the stability of the WO 3 /CuWO 4 photoelectrodes, allowing nearly constant O 2 evolution over 3 hours after an initial 20-35% loss. Overall, this work establishes RF magnetron sputtering as a useful method to install amorphous TiO 2 passivation layers for improved WO 3 /CuWO 4 solar fuel photoelectrodes. Furthermore, we show how the combination of PEC with SPV measurements provides insight into the function of the TiO 2 coatings.

CuWO4↗

DOE OSTI2025

Broken symmetries associated with a Kagome chiral charge order

Chirality, or handedness, is ubiquitous in science, from cell biology to physics, and in condensed matter can underlie exotic phases such as chiral charge density waves and chiral superconductivity. However, detecting subtle broken symmetries that define such states is challenging, leading to debate and controversy. Here, using second-order optical response, we reveal the broken symmetries of a chiral charge density wave in the Kagome lattice KV 3 Sb 5 . Polarization-dependent mid-infrared photocurrent microscopy uncovers a longitudinal, helicity-dependent photocurrent associated with the charge order, indicating broken inversion and mirror symmetries. These findings, supported by theoretical analysis, directly establish the intrinsic chiral nature of the ordered state. Moreover, the absence of a circular photogalvanic effect perpendicular to the incident light imposes stringent constraints on the point-group symmetries. Our study not only visualizes the chiral nature of the Kagome charge order, but also highlights the nonlinear photogalvanic effect as a sensitive probe for detecting subtle symmetry breakings.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2026

Aliovalent gallium dopants remove Ti 3+ defects and improve photocatalytic and photoelectrochemical water oxidation properties of LaTiO 2 N

LaTiO 2 N is a promising semiconductor for the water splitting reaction due to its 2.1 eV band gap and stability against corrosion. However, its solar energy conversion is limited by Ti 3+ recombination defects introduced during ammonolysis. Here we show for the first time that Ti 3+ defects in LaTiO 2 N can be suppressed with incorporation of 2, 5, and 10% aliovalent gallium (Ga 3+ ) dopants during synthesis via the layered La 2 Ti 2 O 7 intermediate. Electron paramagnetic resonance (EPR) spectroscopy on the solid powders confirms a reduction in the Ti 3+ donor density from 2.97 × 10 17 cm −3 for the non-doped material to ∼6.24 × 10 16 cm −3 for 5% Ga-doped LaTiO 2 N. The remaining Ti 3+ defects are concentrated near the LaTiO 2 N surface, according to X-ray photoelectron spectroscopy. The defect reduction shifts the optical absorption edge from 2.02 to 2.09 eV and eliminates a broad absorption band at 1050 nm from the optical absorption spectra. It also removes a 1.0–1.7 eV sub-band gap photovoltage signal from surface photovoltage spectra. This suggests that empty Ti 3+ d-orbitals are located 1.0–1.7 eV above the LaTiO 2 N valence band edge. Removing these recombination states with increasing Ga 3+ content enhances the photoconversion efficiency of LaTiO 2 N during water oxidation. The optimized 2 wt% CoO x -loaded 5% Ga-doped LaTi O2 N material has a 16% AQE (400 nm) for O 2 production from aqueous silver nitrate solution and a ∼2.1 mA cm −2 water oxidation photocurrent at 1.23 V under 100 mW cm −2 Xe arc lamp illumination. The water oxidation photocurrent is stable during a 50 min test, and the Faraday efficiency for O 2 generation is 97%, confirming short-term corrosion stability of LaTiO 2 N. Altogether, these results provide a better understanding of the distribution, concentration, and impact of Ti 3+ defects on the optical, photovoltage, and photoelectrochemical properties of LaTiO 2 N. In combination with other defect control strategies, aliovalent Ga 3+ doping can help bring the solar energy conversion efficiency of LaTiO 2 N closer to the theoretical limit.

Wang, Li [University of California, Davis, CA (Uni↗

DOE OSTI2025

Record performance in intrinsic, impurity-free lateral diamond photoconductive semiconductor switches

Photoconductive semiconductor switches (PCSSs) are fabricated on type IIa diamond substrates with varying boron and nitrogen impurity levels (<10 14 –10 16 cm –3 ). The photoresponse of lateral PCSS is reported over the incident laser wavelength range (212–240 nm), energy per pulse (5–65 μJ), and DC bias (–1.2 to +1.2 kV). The PCSS device with the lowest boron and nitrogen impurity concentration achieves the highest normalized responsivity of 9.1 × 10 –8 A-cm/W-V, peak photocurrent of 8.0 A, and on/off ratio of 2.3 × 10 11 at a DC bias of +1.2 kV with the potential for even higher currents at increased DC bias. All PCSS display fast rise times (<3 ns), limited by the laser's rise time. However, photoresponse measurements reveal that higher impurity levels reduce the photocurrent and decrease the on/off ratio. Furthermore, these results highlight the performance advantages of using low background concentration type IIa diamond substrates for PCSS fabrication and present a promising route toward advanced high-power, high-speed diamond-based switches.

42 ENGINEERING↗

DOE OSTI2025

Annihilation-limited long-range exciton transport in high-mobility conjugated copolymer films

A combination of ultrafast, long-range, and low-loss excitation energy transfer from the photoreceptor location to a functionally active site is essential for cost-effective polymeric semiconductors. Delocalized electronic wavefunctions along π-conjugated polymer (CP) backbone can enable efficient intrachain transport, while interchain transport is generally thought slow and lossy due to weak chain–chain interactions. In contrast to the conventional strategy of mitigating structural disorder, amorphous layers of rigid CPs, exemplified by highly planar poly(indacenodithiophene-co-benzothiadiazole) (IDT-BT) donor-accepter copolymer, exhibit trap-free transistor performance and charge-carrier mobilities similar to amorphous silicon. Here, we report long-range exciton transport in HJ -aggregated IDTBT thin-film, in which the competing exciton transport and exciton–exciton annihilation (EEA) dynamics are spectroscopically separated using a phase-cycling-based scheme and shown to depart from the classical diffusion-limited and strong-coupling regime. In the thin film, we find an annihilation-limited mechanism with ≪100% per-encounter annihilation probability, facilitating the minimization of EEA-induced excitation losses. In contrast, excitons on isolated IDTBT chains diffuse over 350 nm with 0.56 cm 2 s −1 diffusivity, before eventually annihilating with unit probability on first contact. We complement the pump–probe studies with temperature-dependent photocurrent and EEA measurements from 295 K to 77 K and find a remarkable correspondence of annihilation rate and photocurrent activation energies in the 140 K to 295 K temperature range.

Shi, Yuping (ORCID:0000000318289415)↗

DOE OSTI2024

helioLuna: Prospect for cislunar spacecraft and near-earth asteroid detection using heliostat fields at night

We experimentally and computationally investigate a proposed frequency-domain method for detecting and tracking cislunar spacecraft and near-earth asteroids using heliostat fields at night. Unlike imaging, which detects spacecraft and asteroids by their streak in sidereally-fixed long-exposure photographs, our proposed detection method oscillates the orientation of heliostats concentrating light from the stellar field and measures the light’s photocurrent power spectrum at sub-milliHertz resolution. If heliostat oscillation traces out an ellipse fixed in the galactic coordinate system, spacecraft or asteroids produce a peak in photocurrent power spectrum at a frequency slightly shifted from the starlight peak. The frequency shift is on the scale of milliHertz and proportional to apparent angular rate relative to sidereal. Relative phase corresponds to relative angular position, enabling tracking. A potential advantage of this frequency-domain method over imaging is that detectivity improves with apparent angular rate and number of heliostats. Since heliostats are inexpensive compared to an astronomical observatory and otherwise unused at night, the proposed method may cost-effectively augment observatory systems such as NASA’s Asteroid Terrestrial-impact Last Alert System (ATLAS).

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1972

Photocapacitance effects at a Cu2S-CdS heterojunction.

The influence of trapped charge on the photovoltaic properties of an efficient Cu2S-CdS single-crystal heterojunction has been studied by a photocapacitance technique. For the nonheat-treated cell, a persistent increment in capacitance as high as 70% of the dark capacitance remained after illumination of the junction by band-gap light at 100 K. The additional capacitance is due to holes trapped in deep levels in the CdS depletion region near the interface. The trapped holes enhanced the 100 K photocurrent spectrum uniformly by a factor of 3 before heat treatment. After a 200 C heat treatment in air, the maximum trapped charge at 100 K enhanced the photocurrent by two orders of magnitude. The results are interpreted in terms of the tunneling through a conduction band spike of electrons photoexcited in the Cu2S.

Lindquist, P. F.↗

NASA NTRS1975

Laser scanned image sensors using photoconductors with deep traps

Photoconductor records image when holes and electrons are trapped inside it due to incident photons. Image can be read out by exposing photoconductor to scanning laser beam. Photons from scanning laser empty traps, generating photocurrent. Image information is obtained by detecting this photocurrent synchronously with laser scan.

Maserjian, J.↗

NASA NTRS1975

Glass-Si heterojunction solar cells

Experimental studies and models for In2O3/Si and SnO2/N-Si solar cells are considered for their suitability in terrestrial applications. The silicon is the active material, and the glass serves as the window to solar radiation, an antireflection coating of the Si, and a low resistance contact. Results show that amorphous windows or layers suppress photocurrent. The interfacial SiO2 layer suppresses photocurrent and increases series resistance. Suppression increases with illumination.

Anderson, R. L.↗

NASA NTRS1976

Basic corrections to predictions of solar cell performance required by nonlinearities

The superposition principle is used to derive the approximation that the current-voltage characteristic of an illuminated solar cell is the dark current-voltage characteristic shifted by the short-circuit photocurrent. The derivation requires the linearity of the boundary value problems that underlie the electrical characteristics. The shifting approximation is invalid if considerable photocurrent and considerable dark current both occur within the junction space-charge region; it is invalid also if sizable series resistance is present or if high-injection concentrations of holes and electrons exist within the quasi-neutral regions.

Lindholm, F. A.↗