Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Simultaneous x-ray diffraction measurements of nine pressure calibrants to 140 GPa

Accurate pressure calibration is fundamental to quantitative high-pressure science, yet inconsistencies among widely used secondary pressure scales persist. In this work, we report simultaneous synchrotron x-ray diffraction meatogether in diamond anvil cells to 140 GPa. This simultaneous-measurement strategy minimizes transitive errors and run-to-run inconsistencies inherent to paired-measurement approaches, yielding direct experimental volume-volume (V-V) relations among the calibrants. These V-V relations link the compression state of each phase to that of every other phase measured in the same experiment. By anchoring these V-V relations to the reduced 300 K equation of state (EOS) of copper derived from ramp-compression measurements, we derive an internally consistent set of Cu-referenced pressure scales via Vinet EOS fits. Because the primary experimental result is the V-V dataset, it provides an EOS-independent constraint that can be rereferenced if primary standards are revised. The dataset further enables a direct experimental cross-check of consistency between the adopted reduced 300 K Cu EOS and the corresponding reduced 300 K ramp-derived EOSs for Pt, Au, Ta, and hcp-Fe under a fixed V-V constraint. The residuals quantify small, material-dependent mismatches between each phase EOS and the Cu reference EOS.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Atomic oxygen density determination in the effluent of the COST reference source using in situ effective lifetime measurements in the presence of a liquid interface

Abstract Spatially resolved, absolute densities of atomic oxygen are measured for several helium-based admixtures in the effluent of the COST Reference Microplasma Jet using two-photon absorption laser induced fluorescence (TALIF). Admixtures investigated include a helium-only admixture, four helium/oxygen admixtures (0.1 % , 0.5 % , 0.6 % , and 1.0 % oxygen), and a helium/water admixture (2500 ppm water), chosen to coincide with previously published characterizations of plasma-treated liquid. The atomic oxygen TALIF signal is calibrated for density using the noble gas xenon, which possesses a very similar two-photon excitation and fluorescence scheme. Measurements are conducted for the jet operating in ambient air with both an open effluent and a liquid surface present, allowing for comparison with liquid phase measurements conducted under similar conditions. The presence of a water surface does not appear to alter the background chemistry in the effluent but reduces O densities close to the liquid interface when compared to a similar distance from the nozzle in an open effluent case. This may be the result of a reduction in flow velocity caused by the liquid obstructing the gas flow. Additionally, measurements near the liquid surface revealed a region of atomic oxygen well outside of where the core of the effluent impinges on the liquid. This is likely relevant for applications as it considerably expands the surface area subject to O absorption. Critically, in situ measurements of the effective lifetimes of the laser-excited 3p 3 P J state of atomic oxygen were recorded in the effluent by employing a picosecond (ps) laser and a nanosecond (ns) ICCD. By experimentally determining the contribution from collisional quenching via the in situ effective lifetime measurements, significant improvements in the accuracy of the atomic oxygen density calibration were made, with differences of approximately 30 % from existing methods of estimating quenching rates at atmospheric pressure. Finally, spatially resolved atomic oxygen densities allow for an investigation of O formation and extinction pathways in the effluent and a comparison between admixtures.

laser diagnostics↗
DOE OSTI2026

Field and Model Data Associated with the Manuscript “Drivers of Streamflow Intermittency in Humid Regions: 1. Evaluating Above- and Below-ground Controls of Flow Persistence in a Forested Catchment”

This package contains field data, modeling files, and scripts supporting the investigation of the drivers of streamflow intermittency in a forested catchment. It includes the field data collected from electrical resistivity tomography (ERT) surveys, ground penetrating radar (GPR), continuous self-potential (SP) monitoring, electromagnetic (EM) imaging, groundwater and stilling well. In addition, it contains the data and results of the coupled water- and electrical-flow model developed using the COMSOL Multiphysics and Advanced Terrestrial Simulator (ATS), as well as software files and Jupyter notebooks used to process the data and generate figures in the manuscript submitted for peer review. The data archive is organized in the following directories: 1) Climate Includes hourly precipitation and daily evapotranspiration time series (2024 – 2025) provided as CSV files, alongside a text file detailing dataset units. 2) Coupled_model Contains two subfolders: Synthetic and Field_Application subfolder. Synthetic subfolder contains the ATS XML input script (can be opened using any code editor) for the four synthetic hydrological cases tested (Connected and gaining, Connected and losing, Disconnected and losing, and dry stream). It also includes other experimental cases to test the influence of precipitation and concentration gradient. For each synthetic case, the flow model simulation is executed using the ATS XML scripts and the included Python script (generate_data_set.py) to convert ATS output to COMSOL-ready input. COMSOL Multiphysics template (.mph can be opened with the commercial software COMSOL and requires a license) is executed using the ATS output data to simulate the potential field. It also includes the Synthetic_model_plot.ipynb (can be opened using any code editor) to visualize the SP result and generate manuscript figures. The data subfolder contains mesh files to run both the ATS (.exo and .stl files can be viewed using Paraview; .h5 files can be opened using HDFView software and h5py Python package) and COMSOL models. Field_Application subfolder contains two subfolders: ES_MDA_inversion and Final_Model. ES_MDA_inversion contains the Python script (.py can be opened using any code editor) and SP observation data used to run the Ensemble Smoother with Multiple Data Assimilation (ES-MDA) inversion sequence to get the optimal model parameters. The Final_model subfolder contains the ATS XML input scripts, data files, output data for the two SP sites. The same workflow steps outlined for the Synthetic subfolder apply here. It also contains the Jupyter notebook (Plot_final_calib.ipynb) to visualize the results of the modeled SP, stream-groundwater exchange and moisture content. 3) Discharge Includes the electrical conductivity (EC) time series (provided as CSV files) from salt slug injections. It also includes the Jupyter notebook (Discharge_process.ipynyb) used to estimate discharge. All discharge measurements collated into rating_curve_processed.csv 4) EM Contains the CSV file of the EM data from the DUALEM-42, including spatial coordinates (x, y, z), apparent conductivity, and in-phase measurements at 2 m coil separations for horizontal coplanar (HCP) and perpendicular (PRP) geometries. 5) ERT Contains raw resistivity data (provided as CSV files), spatial location of each of the electrodes (provided as CSV files), and files used for the resistivity inversion (.resipy can be opened with the open-source ResIPy software). 6) GPR Includes GPR field datasets collected at 100 MHz and 250 MHz antenna frequencies, along with the processing/interpretation project file (GPR_process.gpz can be viewed using EKKO_Project 6, a commercial software by Sensors & Software that requires a license). 7) Slug_test Includes the slug test data at all the groundwater wells provided as CSV files, as well as the Jupyter notebook (Slug_test.ipynb) for calculating hydraulic conductivity. 8) SP Contains the SP data collected in field at the two SP sites (one in the perennial reach and the other in the intermittent reach), provided as DAT files. 9) Well_data Contains two subfolders: 1) Raw, which provides unprocessed pressure, electrical conductivity and temperature timeseries downloaded from the loggers in all the groundwater and stilling wells, and 2) Processed, which contains sorted, QA/QC timeseries data for each well. The data archive also contains data_process.ipynb, a Jupyter notebook used for field data analysis and generating figures (plotting well, SP, climate, and discharge data, as well as calculating head gradient at sites with nested groundwater wells). It also includes DTW.ipynb, a Jupyter notebook containing the code for the dynamic time warping (DTW) with sliding window to evaluate SP signal synchronicity.

ATS↗
DOE OSTI2022

Cross-polarized common-path temporal interferometry for high-sensitivity strong-field ionization measurements

Absolute density measurements of low-ionization-degree or low-density plasmas ionized by lasers are very important for understanding strong-field physics, atmospheric propagation of intense laser pulses, Lidar etc. A cross-polarized common-path temporal interferometer using balanced detection was developed for measuring plasma density with a sensitivity of ∼0.6 mrad, equivalent to a plasma density-length product of ∼2.6 × 10 13 cm −2 if using an 800 nm probe laser. By using this interferometer, we have investigated strong-field ionization yield versus intensity for various noble gases (Ar, Kr, and Xe) using 800 nm, 55 fs laser pulses with both linear (LP) and circular (CP) polarization. The experimental results were compared to the theoretical models of Ammosov-Delone-Krainov (ADK) and Perelomov-Popov-Terent’ev (PPT). We find that the measured phase change induced by plasma formation can be explained by the ADK theory in the adiabatic tunneling ionization regime, while PPT model can be applied to all different regimes. We have also measured the photoionization and fractional photodissociation of molecular (MO) hydrogen. By comparing our experimental results with PPT and MO-PPT models, we have determined the likely ionization pathways when using three different pump laser wavelengths of 800 nm, 400 nm, and 267 nm.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

EPCAPE-PT-LANL Measurements: PM Modulair 1

Coastal cities offer a unique environment for studying aerosol-cloud interactions and the effects of urban emissions on cloud properties. As part of the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), the Partitioning Thrust by Los Alamos National Laboratory (EPCAPE-PT-LANL) was conducted. Our campaign focused on measuring the optical and chemical properties of aerosols and their interactions within marine stratocumulus clouds in La Jolla, California. EPCAPE-PT-LANL enhances the primary goals of EPCAPE through innovative observations of vapor-phase transitions between aerosols and cloud droplets, the impact of black carbon on aerosol-cloud dynamics, and the effects of cloud processing on aerosol optical properties. Instrument: Quant-AQ MODULAIR. Mounted external to the instrument container, near the GCVI inlet. The MODULAIR™ air quality monitor uses the same patent-pending PM sensor found in the MODULAIR™-PM and adds four gas-phase measurements (CO, NO, NO2, and O3) to provide an all-in-one solution. Files data_10sec_Quant_Gas.csv, data_10min_Quant_Gas.csv Header: - CO[ppb]: Concentration of carbon monoxide (CO) measured at the time of sampling, expressed in parts per billion (ppb) - NO[ppb]: Concentration of nitric oxide (NO) measured at the time of sampling, expressed in parts per billion (ppb). - O3[ppb]: Concentration of ozone (O3) measured at the time of sampling, expressed in parts per billion (ppb). - Temperature[C]: The ambient temperature at the time of the measurement, expressed in degrees Celsius. - RelativeHumidity[%]: The relative humidity at the time of the measurement, expressed as a percentage. Files data_10sec_Quant_PM.csv, data_10min_Quant_PM.csv Header: - PM1[ug/m3]: Concentration of particulate matter with a diameter of 1 micron or less, measured in micrograms per cubic meter (µg/m³). - PM2-5[ug/m3]: Concentration of particulate matter with a diameter of 2.5 microns or less measured in micrograms per cubic meter (µg/m³). - PM10[ug/m3]: Concentration of particulate matter with a diameter of 10 microns or less, measured in micrograms per cubic meter (µg/m³). - Temperature[C]: The ambient temperature at the time of the measurement, expressed in degrees Celsius. - RelativeHumidity[%]: The relative humidity at the time of the measurement, expressed as a percentage.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Analytically differentiable metrics for phase stability

Here, in this work, a long-established but sparsely documented method of obtaining semi-analytic derivatives of thermodynamic properties with respect to equilibrium conditions is briefly reviewed and rigorously derived. This procedure is then leveraged to construct general forms of derivatives of the residual driving force, a metric for measuring phase stability used in CALPHAD model optimization, with respect to overall system and individual phase compositions. Applied examples – calculating heat capacity in the Al-Fe system, thermodynamic factors in the Nb-V-W system, and residual driving force derivatives in the Ni-Ti system – demonstrate the versatility, accuracy, and extensibility of this method. Using the developed method, residual driving force gradients can be applied directly in CALPHAD model optimizers, as well as in materials design frameworks, to identify regions of phase stability with an efficient, gradient-based approach.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Materials design, synthesis, and transport properties of disordered rare-earth Zintl bismuthides with the anti -Th 3 P 4 structure type

The synthesis, structural elucidation, and transport properties of the extended series Ca 4–x RE x Bi 3 (RE = Y, La–Nd, Sm, Gd–Tm, and Lu; x ≈ 1) and Ca 4–x RE x Bi 3–δ Sb δ (RE = La, Ho, Er, and Lu; x ≈ 1, δ ≈ 1.5) are presented. Structural elucidation is based on single-crystal X-ray diffraction data and confirms the chemical drive of Ca4Bi3 with the cubic anti-Th 3 P 4 structure type (space group I4 ¯3d, no. 220, Z = 4) into a Zintl phase by the introduction of trivalent rare-earth atoms. The structure features complex bonding, heavy elements, and electron count akin to that of valence-precise semiconductors, making it an ideal target for thermoelectrics development. Introducing crystallographic site disorders at the cation site for the Ca 4–x RE x Bi 3 phase and both the cation and anion sites for the Ca 4–x RE x Bi 3–δ Sb δ phase brings about additional desirable characteristics for thermoelectric materials in the context of tuning knobs for lowering thermal conductivity. Electronic structure calculations of idealized Ca 3 YBi 3 and Ca 3 LaBi 3 compounds indicate the opening of indirect bandgaps at the Fermi level with magnitudes Eg = 0.38 eV and 0.57 eV, respectively. The electrical resistivity ρ(T) of some of the investigated phases measured on single crystals evolve in a metallic manner with magnitudes of order 1.4 mΩ cm near 500 K, thus supporting the notion of a degenerate semiconducting state, with the temperature dependence of the Seebeck coefficient α(T) suggesting the p-type behavior. Furthermore, the low electrical resistivity and the realization of a degenerate semiconducting state in the title phases present a window of opportunity for optimizing their carrier concentrations for enhanced thermoelectric performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Achieving a near-ideal silicon crystal neutron interferometer using submicrometer fabrication techniques

Perfect-crystal neutron interferometry, which is analogous to Mach-Zehnder interferometry, uses Bragg diffraction to form interfering neutron paths. The measured phase shifts can be used to probe many types of interactions whether it be nuclear, electromagnetic, gravitational, or topological in nature. For a perfect-crystal interferometer to preserve coherence, the crystal must possess a high degree of dimensional tolerance as well as being relatively defect-free with minimal internal stresses. In the past, perfect-crystal neutron interferometers have been produced by a two-step process. First, a resin diamond wheel would be used to remove excess material and shape the interferometer. Afterword, the crystal would be etched to remove surface defects and elevate strains. This process has had limitations in terms of repeatability and in maximizing the final contrast, or fringe visibility, of the interferometer. We have tested various fabrication and post-fabrication techniques on a single perfect-crystal neutron interferometer and measured the interferometer's performance at each step. Here we report a robust, nonetching fabrication process with high final contrast. For the interferometer used in this work, we achieved contrasts of greater than 90% several times and ultimately finished with an interferometer that has 92% contrast and a uniform phase distribution. Published by the American Physical Society 2024

Huber, M. G. (ORCID:0000000237958445)↗
DOE OSTI2023

Online detection of airborne nanoparticle composition with mass spectrometry: Recent advances, challenges, and opportunities

Airborne nanoparticles are receiving growing attention due to their impacts on human health, air quality, and climate. Additionally, there are increasing applications of aerosol-based nanotechnology. Real-time measurement of airborne nanoparticle composition is challenging due to their small masses and the difficulties in effectively separating them from larger particles. Custom-built instruments based on mass spectrometry have been developed for nanoparticle composition, including thermal desorption-based, laser-based, and solution-based techniques. They have significantly promoted the understanding of airborne nanoparticles in the last two decades. However, they are affected by molecular fragmentation, lack of mass-resolving power, incomplete species detection, and difficulties in directly comparing to gas-phase measurements. Recent developments in atmospheric mass spectrometry provide possible solutions. Here, this review presents the potential application of these new advances to real-time measurements of the molecular nanoparticle composition and discusses the associated challenges. Such measurements present opportunities for a more comprehensive view of airborne nanoparticles and their impacts.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Modeling impurity concentrations in liquid argon detectors

Impurities in noble liquid detectors used for neutrino and dark matter experiments can significantly impact the quality of data. We present an experimentally verified model for describing the dynamics of impurity distributions in liquid argon (LAr) detectors. The model considers sources, sinks, and transport of impurities within and between the gas and liquid argon phases. Measurements of oxygen concentrations in a 20-L LAr multi-purpose test stand are compared to calculations made with this model to show that an accurate description of the concentrations under various operational conditions can be obtained. A result of this analysis is a determination of Henry’s coefficient for oxygen in LAr. Additionally, these calculations also show that some processes have small effects on the impurity dynamics and excluding them yields a solution as a sum of two exponential terms. This solution provides a simple way to extract Henry’s coefficient with negligible approximation error. It is applied to the data and the Henry’s coefficient for oxygen in LAr is obtained as 0.84 +0.09 -0.05 , consistent with literature results. Finally, based on the analysis of the data with the model, we further suggest that, for a large liquid argon detector, barriers to flow (“baffles”) installed in the gas phase to restrict flow can help reduce the ultimate impurity concentration in the LAr.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Single-shot measurement of longitudinal phase space beam profile in an electron storage ring

A novel scheme to measure the longitudinal emittance and phase space profile in an electron storage ring by using correlations between time and the vertical coordinate, and between energy and the horizontal coordinate, is proposed. This longitudinal profile measurement scheme will help to demonstrate recent results of advanced studies for manipulating the longitudinal beam profile and for investigating beam instability in an electron storage ring.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

2023 American Society for Mass Spectrometry (ASMS) 71st Annual Conference on Mass Spectrometry and Allied Topics

Introduction (120 words max) Understanding metal-cluster chemistry occuring at solvent boundaries in the aqueous and organic phases has applications in environments from cellular processes to nuclear fuel reprocessing. Transport of metal ions at the boundaries from aqueous to organic phases involves forming a metal-ligand complex, and wherever the initial metal coordination environment is significantly different from the final one, the metal transitions through a series of transient species in passing from one phase to another. Here an investigation of the role of coordination in the chemistry of the transient species using gas-phase measurements that are free of solvent effects to better understand the binding of complexes of metals with triphenylphosphine chalcogenide ligands, examining metal-ligand homo- and hetero-dimers to better understand transient species. Methods (120 word max) Mass spectrometry and collision induced dissociation (CID) experiments were performed with a Bruker (Billerica, MA, USA) micrOTOF-Q II quadrupole time-of-flight mass spectrometer (QTOF) and Bruker amaZon speed ETD (ion trap). High resolution/high mass accuracy spectra were generated using the QTOF. External calibration was performed with Agilent (Santa Clara, CA, USA) ESI-L Low Concentration tuning mix. Both mass spectrometers were equipped with either the electrospray ionization source or nanospray sources. Metal samples were prepared between 40 – 60 uM of the metal-ligand complex in 25% water and 75% acetonitrile. Metal-ion clusters were isolated and subjected to collision induced dissociation. Density functional theory calculations were performed. Preliminary Data or Plenary Speakers Abstract (300 words max) Metal ion clusters with triphenylphosphine chalcogenide ligands were observed for group I metals with triphenylphosphine chalcogenide samples in the mass spectrum upon electrospray ionization. For each metal ligand complex of interest, the parent ion was isolated and collision induced dissociation fragmentation spectra were acquired. We observed clusters of group I metal with triphenylphosphine oxide, triphenyl phosphine sulfide, and triphenylphosphine selenide, with homodimers and heterodimer formation. In samples where the ligands were mixed, we observed mixed sodium ligand clusters at varying amounts. These mixed ligand clusters were fragmented. Metal clusters of mixed ligand dimers containing triphenylphosphine oxide showed preferential loss of the other ligand, either triphenylphosphine sulfide or triphenyl selenide. In samples with mixed triphenylphosphine sulfide and triphenylphosphine selenium ligands, sodium bound similarly between the ligands, and losses were more evenly split, showing loss ratio upon CID with losses of triphenylphosphine sulfide:triphenylphosphine selenide 43:57 ratio observed on CID. These results suggest that the oxide binds significantly more strongly than either the selenium or sulfur triphenylphosphine ligand, and the sulfur and selenium ligands are more evenly bound. Calculations were performed using density functional theory to calculate likely structures and bond energies between the group I metal and the ligands. Novel Aspect Novel analysis of sodium bound dimers with chalcogenide triphenylphosphine ligands were investigated using mass spectrometry and theoretical calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The Effects of Silicon and Niobium Concentration on the Solidification Behavior and Microstructure of Cast Monel Alloys

Cast Monel alloys are used in applications requiring a combination of good mechanical properties and excellent resistance to corrosion. Despite prevalent industrial use, relatively few studies have been conducted to investigate the relationships between composition, solidification behavior, and microstructure. Given that these alloys are used in the cast and welded conditions, these factors have a significant influence over the material properties. Here, in this work, microstructural characterization, electron probe microanalysis, X-ray diffraction, and differential scanning calorimetry were used to study how changes in Si and Nb concentrations affected the solidification path and microstructure of Monel alloys. It was found that increasing Nb concentration stabilized higher amounts of MC carbides and suppressed graphite formation during solidification. It was also found that the high nominal concentration and segregation of Si to the liquid led to the formation of Ni 31 Si 12 and other silicides via terminal eutectic reactions at the end of solidification. A pseudo-binary solidification diagram was constructed using experimental data and was applied to predict the mass fraction of solidified eutectic as a function of composition. The modeled microstructures were found to be in good agreement with experimentally measured phase fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Wave and Particle Analysis of Z-Mode and O-Mode Emission in the Jovian Inner Magnetosphere

We report some of the most intense Z-mode and O-mode observations obtained by the Juno spacecraft while in orbit about Jupiter in a low to mid-latitude region near the inner edge of the Io torus. We have been able to estimate the density of the plasma in this region based on the lower frequency cutoff of the observed Z-mode emission. The results are compatible with the electron density measurements of the Jovian Auroral Distributions Experiment (JADE), on board the Juno spacecraft, if we account for unmeasured cold plasma. Direction-finding measurements indicate that the Z- and O-mode emission have distinct source regions. We have also used the measured phase space density of the JADE and the Jupiter energetic particle detector instruments to calculate estimated local growth rates of the observed O-mode and Z-mode emission assuming a loss cone instability and quasilinear analysis. The results suggest the emissions were observed near, but not within, a source region, and the free energy source is consistent with a loss cone. We have thus carried out the quasilinear wave analysis of the assumed remote Z- and O-mode wave growths. It is shown that the remotely generated waves, propagated through an inhomogeneous medium to the satellite location, may account for the observed wave characteristics. The importance of Z-mode in accelerating electrons in the inner Jovian magnetosphere makes these new wave mode confirmations at Jupiter of particular interest.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Water flipping and the oxygen evolution reaction on Fe 2 O 3 nanolayers

Hematite photoanodes are promising for the oxygen evolution reaction, however, their high overpotential (0.5-0.6 V) for water oxidation and limited photocurrent make them economically unviable at present. The work needed to orient dipoles at an electrode surface may be an overlooked contribution to the overpotential, especially regarding dipoles of water, the electron source in the oxygen evolution reaction (OER). Here, we employ second harmonic amplitude and phase measurements to quantify the number of net-aligned Stern layer water molecules and the work associated with water flipping, on hematite, an earth abundant OER semiconductor associated with a high overpotential. At zero applied bias, the pH-dependent potentials for Stern layer water molecule flipping exhibit Nernstian behavior. At positive applied potentials and pH 13, approximately one to two monolayers of water molecules points the oxygen atoms towards the electrode, favorable for the OER. The work associated with water flipping matches the cohesive energy of liquid water (44 kJ mol -1 ) and the OER current density is highest. This current is negligible at pH 5, where the work approaches 100 kJ mol -1 . Our findings suggest a causal relationship between the need for Stern layer water flipping and the OER overpotential, which may lead to developing strategies for decreasing the latter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Sulfate reduction accelerates groundwater arsenic contamination even in aquifers with abundant iron oxides

Groundwater contamination by geogenic arsenic is a global problem affecting nearly 200 million people. In South and Southeast Asia, a cost-effective mitigation strategy is to use oxidized low-arsenic aquifers rather than reduced high-arsenic aquifers. Aquifers with abundant oxidized iron minerals are presumably safeguarded against immediate arsenic contamination, due to strong sorption of arsenic onto iron minerals. However, preferential pumping of low-arsenic aquifers can destabilize the boundaries between these aquifers, pulling high-arsenic water into low-arsenic aquifers. We investigate this scenario in a hybrid field-column experiment in Bangladesh where naturally high-arsenic groundwater is pumped through sediment cores from a low-arsenic aquifer, and detailed aqueous and solid-phase measurements are used to constrain reactive transport modelling. Here we show that elevated groundwater arsenic concentrations are induced by sulfate reduction and the predicted formation of highly mobile, poorly sorbing thioarsenic species. Furthermore, this process suggests that contamination of currently pristine aquifers with arsenic can occur up to over 1.5 times faster than previously thought, leading to a deterioration of urgently needed water resources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Entangled-photon interferometry for plasmas

Subpicosecond coincidence timing from nonlocal intensity interference of entangled photons allows quantum interferometry for plasmas. Using a warm plasma dispersion relation, we correlate phase measurement sensitivity with different plasma properties or physics mechanisms over six orders of magnitude. Due to Nα (α≤−1/2) scaling with the photon number N, quantum interferometry using entangled light can probe small signals in plasmas not previously accessible. As an example, it is predicted that plasmas will induce shifts to a Gaussian dip, a well-known quantum optics phenomenon that is yet to be demonstrated for plasmas.

Wang, Zhehui (ORCID:0000000178264063)↗
DOE OSTI2024

Variable-spectrum mode control of high poloidal beta discharges

DIII-D experiments demonstrate that high pressure, broad current profile equilibria can be accessed in the high poloidal beta regime by optimizing the MHD mode control poloidal spectrum. A novel, variable spectrum (VS) magnetic feedback scheme implemented using the DIII-D internal non-axisymmetric coils (I-coils) facilitated access to reduced internal inductance $l$ i operation above the no-wall beta limit compared with both no feedback and fixed spectrum feedback. In addition, the VS feedback helped avoid beta collapses caused by marginally unstable resistive wall mode activity. The lower and upper I-coil rows were configured in two independent feedback loops, allowing the feedback field's poloidal spectrum to vary and track changes in the plasma mode structure as the edge safety factor q 95 varied from 11 to 6 during the discharges. The q 95 dependence of the measured phase difference between the lower and upper I-coil rows during VS feedback is qualitatively compatible with ideal MHD simulations of the least-stable plasma kink mode and with plasma response simulations that included kinetic modifications to ideal MHD. The VS feedback approach is a straightforward way to improve resilience to variations in mode structure that occur as plasma parameters change. The demonstrated expansion of the operating space to lower $l$ i is expected to improve the coupling of the plasma kink mode to external fields and beneficial wall eddy currents, and is compatible with high bootstrap fraction operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗