Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase change”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Combining Theory and Experiment to Map the Atomic-Level Structure–Energy Pathways of Adsorbate-Mediated Phase Changes in a Cooperatively Flexible Metal–Organic Framework

An important subclass of metal–organic frameworks (MOFs) exhibits cooperative flexibility, wherein individual crystallites undergo global structural phase changes in response to external stimuli. Where cooperative flexibility results in reversible changes between crystalline states of distinct accessible porosity, these frameworks can exhibit rare yet desirable behaviors that cannot be explained by local dynamics alone. Yet, the chemical and structural origins of cooperative flexibility and how frameworks undergo these reversible phase changes at the atomic level remain poorly understood. Deliberate design for specific applications is therefore exceedingly difficult, and there is great impetus to develop a fundamental understanding of this phenomenon. Here, an effective and widely accessible computational approach is developed, which is designed to provide microscopic resolution via direct comparison to experimental data along the desorption-guided pathway. The strategy is applied to explain the desorption-induced phase change in an experimentally well-characterized framework, CdIF-13 (sod-Cd(benzimidazolate)2), where experiment alone was unable to resolve the atomistically detailed phase change landscape. Our findings reveal that the cooperative phase change pathways are adsorbate dependent with thermodynamics of intermediate structural states dictated by a nuanced interplay of ligand orientation, skeletal symmetry, and modes of surface adsorption. The results reveal that this isotropically flexible framework is “chaperoned” through a complex energy landscape by specific adsorbates, revealed by the reported computational approach with atomic-level insight and validated by experimentally determined structures. Thus, this work facilitates both understanding and future design of flexible materials for applications in gas storage, transport, delivery, and separation technologies.

03 NATURAL GAS↗
DOE OSTI2023

A unified non-equilibrium phase change model for injection flow modeling

The homogenous relaxation model (HRM) is one of the most widely used models to describe the liquid- gas phase transition. However, in its original formulation, it is unable to handle multispecies vapor-liquid equilibrium (VLE), which limits its applicability to single-component fluids. In this work, a unified non-equilibrium phase change model that considers the VLE of multicomponent mixtures is proposed building upon the HRM's structure. A time factor is introduced to mimic the effect of different phase change timescales due to different mechanisms, e.g., cavitation, flash-boiling, and evaporation. Here to assess the model's performance, computational fluid dynamics simulations of the internal and near-nozzle injection flow of the Engine Combustion Network's Spray G injector were performed using the nine-component PACE-20 fuel with both the unified model and the original HRM. The predicted fuel density in the near-nozzle region matched well with X-ray tomography measurements. The simulation results indicated that, whereas the HRM failed to capture the vaporization due to convective mixing between the fuel and ambient gas, the unified model performed well in predicting the mixing-driven vaporization and the corresponding evaporative cooling. Further comparisons using the nine-component fuel formula and a single-component fuel surrogate demonstrated the unified model's ability to predict preferential vaporization, which affects the predictions of local mixture composition and rate of vaporization. Finally, it is shown that the unified model is capable of representing multiple phase change mechanisms, and the relaxation time factor plays an important role in determining the degree of phase change due to the different mechanisms.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Experimental Investigation of a Phase Change Material Charged Finned-Tube Heat Exchanger

Understanding different thermal performance aspects of phase change material heat exchangers (PCM-HX) is critical for designing future energy-efficient thermal energy storage systems. This paper presents an experimental performance analysis of a vertically oriented annular finned-tube PCM-HX in a cylindrical container tested under six different melting and solidification test conditions, varied by heat transfer fluid’s (HTF) inlet temperatures and flow directions. The PCM-HX structure with 20 evenly spaced fins was 3D printed in aluminum, and the PCM-HX container was 285 mm in height. The PCM-HX average porosity was 89.7%, where the PCM mass was 246.4 g. Water served as the HTF, and a PCM with a nominal phase change temperature of 35 °C was selected. Instead of opaque conventional insulation sheets, a combination of air-and-argon-filled see-through insulation cylinders was assembled with the PCM-HX to visualize the phase-change phenomena, while minimizing the uncertainties due to heat loss. In total, there were 78 T-type thermocouples installed in the test section which allows a more precise assessment of thermal mass and heat loss, which are often neglected in similar studies found in the literature. We validated the reliability of the test facility as the repeated test results had negligible deviations under the same test conditions. The energy balances between the estimated theoretical and experimentally calculated PCM storage, considering heat loss and thermal mass, were within ±9% deviation for all test conditions. From the experimental investigations, we made several following observations. It was found that the melting pattern of the finned-tube PCM-HX with small gaps between the container wall and the fins was largely affected by the HTF flow directions, unlike the typical straight annular tube PCM-HX. For effective charging and discharging processes, a combination of upward melting and downward solidification is recommended to shorten the test duration. However, an upward solidification should be considered to minimize the cavity formation between the fins caused by the PCM volume contraction during the solidification process.

25 ENERGY STORAGE↗
DOE OSTI2026

A Novel and Scalable Method for Microencapsulating Salt Hydrate Phase Change Materials in Core–Shell Fibers

Phase change materials (PCMs) are in high demand for applications such as thermal energy storage in buildings, electronics cooling, and thermal management of electric vehicle batteries and data centers. Among these materials, salt hydrate PCMs are particularly attractive due to their high thermal energy storage capacity and low cost. However, they suffer from two major issues: leakage in the melted phase and phase segregation during phase transitions. Microencapsulation is the primary process capable of addressing both of these challenges. However, there is no reliable or scalable method available for microencapsulating salt hydrate PCMs. As a result, the full potential of salt hydrates for building and data center applications has yet to be realized. In this work, we present an innovative method for the microencapsulation of salt hydrate PCMs using a co‐axial pushing technique. This process creates core–shell fibers, with the salt hydrate as the core and a polymer as the shell. Our approach demonstrates strong potential for scalable microencapsulation of salt hydrate PCMs. In conclusion, achieving scalability could enable their widespread use in applications such as data center cooling, battery thermal management, and building climate control.

Sharma, Jaswinder [Oak Ridge National Laboratory (↗
DOE OSTI2022

Techno-Economic Analysis of Dynamic Building Envelopes Comprising Phase Change Materials and Switchable Insulations

Integrating phase change materials (PCMs) in building envelopes is a recognized technique to reduce the space heating/cooling loads and provide load shedding and shifting capacity. However, PCM benefits have been found to reduce dramatically with increase in the insulation requirements. Dynamic building envelopes that can alter their thermal resistance based on the indoor and outdoor conditions can effectively harness free ambient heating/cooling, thereby greatly enhancing the benefits of the PCM-integrated envelope in managing thermal loads. In this study, we examine various combinations of PCMs and switchable insulations and compare their combined impact on heat flow through the building envelope. Using numerical analysis, we investigate the PCM- and switchable insulation-integrated building walls, calculate the potential energy saving benefits compared to the conventional static walls, and finally perform techno-economic analysis to estimate the acceptable cost of the technology under various payback period scenarios.

dynamic building envelopes↗
DOE OSTI2020

Metal-insulator transition and doping-induced phase change in Ge 2 Sb 2 Se 5x Te 5-5x

Ge 2 Sb 2 Te 5 (GST-225), a phase change material (PCM) with vast differences in the electrical and optical characteristics between its amorphous and crystalline phases, is revisited to explore its properties with Se doping. GST crystallizes in a layered hexagonal ground state, while the precursor to the amorphous state is a distorted rock salt like structure with vacancies at the Ge/Sb sites. Upon doping, liquid nitrogen quenched Ge 2 Sb 2 Se 5x Te 5-5x (GSST-225) exhibits a direct hexagonal-to-amorphous phase change above x > 0.8, whereas the rock salt like structure appears as a second phase with a volume fraction that does not change as a function of the doping. The phase change is accompanied by a metal-to-insulator transition (MIT), with a several orders of magnitude increase in the resistivity on approaching the amorphous state. Additionally, a similar MIT is observed even without the phase change in hexagonal crystals with doping levels above x >0.8. On warming amorphous GSST (x = 0.9) above room temperature, a reversal to the hexagonal phase occurs with a re-crystallization onset temperature (T c ) above 300 °C, much higher than the T c (~170 °C) of amorphous GST and an activation energy of 1.47 eV, which is comparable to good glass formers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Shape-stabilized phase change materials for energy storage based on hierarchically porous calcium magnesium carbonate

A composite phase-change material containing a hierarchically porous Ca 1-x Mg x CO 3 and having pores loaded with a phase change material is described. The heat storage material has a latent heat of melting 123 to 221 J/g, a latent heat of freezing of 107 to 201 J/g, and a thermal conductivity of 0.22 to 0.45 W·m −1 ·K −1 . The phase change material may be polyethylene glycol, and the polyethylene glycol does not leak from the pores of the hierarchically porous Ca 1-x Mg x CO 3 when heating or cooling over phase transitions.

25 ENERGY STORAGE↗
DOE OSTI2021

Integrated Heat Exchanger-Phase Change Material Thermal Energy Storage System

The purpose of this study is to experimentally investigate the thermal performance of an innovative thermal energy storage (TES) system that combines the advantages of the phase-change material (PCM)/graphite foam latent heat TES medium developed at Argonne National Laboratory (Argonne) and the internally supported plate-fin (ISPE) cell architecture heat transfer fluid (HTF) flow channels developed at Brayton Energy (Brayton). Several essential tasks were accomplished: (1) Thermal property characterization. Thermal properties of the graphite foam were characterized, providing necessary data for experimental result analysis and numerical simulation. (2) Design and optimization of lab-scale test module. Based on Brayton’s full-scale heat exchanger (HX)-TES system, the experimental test module was designed, optimized, and fabricated. (3) Thermal performance testing and data analysis. Five cycle tests were successfully conducted—including one with approximately 3.5 psig of pressure applied to the diaphragms—to investigate the thermal performance of the experimental test module for charging and discharging. Temperature profiles were generated for each charging test and discharging test as a function of time. The temperature profiles clearly show three TES stages: sensible heat (temperature increase), latent heat (melting), and sensible heat (temperature increase) for the charging process. Similarly, the temperature profiles clearly show three thermal energy release stages: sensible heat (temperature decrease), latent heat (solidification), and sensible heat (temperature decrease). Melting and solidification of the PCM generally occurred in relatively narrow temperature ranges, indicated by the flattened temperature regions in the temperature profiles. These phase changes ranged approximately 3°C for melting and 3.5°C for solidification. The charging and discharging temperature profiles were similar for similar experimental parameter tests whether or not pressure was applied to the diaphragm to eliminate the gap between the HX surface and the TES subsystem. This indicates that the effect of a small gap between the HX surface and the TES subsystem is insignificant for charging and discharging. (4) Comparison of experimental data and simulation results. We compared the experimental data to the numerical simulation results. Numerical simulations were conducted by using the ANSYS FLUENT 2019 R3 commercial computational fluid dynamics software. The predicted phase-change times agreed reasonably well with those from the experimental data. In most cases, the estimated time differences between the relative phase changes were within 16%. The predicted start and end times for the charging process agreed well with those from the experimental data. However, the simulation results showed earlier start and end times than the experimental data for the discharging process. Overall, the experimental data and its comparison with the simulation predictions verified the technical viability of the integrated ISPF HX-PCM/graphite foam latent-heat TES system.

25 ENERGY STORAGE↗
DOE OSTI2023

Experimental Investigation of a Phase Change Material Charged Serpentine Heat Exchanger with Louvered Fins

Phase change material heat exchangers (PCM-HX) can be used as a latent heat thermal energy storage (LHTES) component in heat pump applications to further enhance the efficiency of a heat pump as well as to yield financial savings by peak-load shifting. In this paper, a low-cost commercially available aluminum serpentine heat exchanger with louvered fins was experimentally investigated to check its thermal performance as a PCM-HX. A transparent rectangular box fabricated from acrylic plates served as a PCM container. Two cameras were used to capture the phase change process of the PCM on the front and top sides of the container during the experiment. A total of 88 installed temperature sensors throughout the test setup and a mass flow meter enabled a quantitative analysis of the PCM-HX as well. The energy balance deviation between the estimated theoretical and experimentally calculated PCM storage was ±14% considering the often-neglected heat loss and thermal mass of the PCM-HX. PCM temperature profiles, charge and discharge rates, and energy densities under different test conditions were also investigated.

42 ENGINEERING↗
DOE OSTI2021

Dual Phase Change Thermal Diodes with High Rectification for Thermal Management near Room Temperature

Thermal diodes are passive systems that modulate their thermal resistance depending on the direction of temperature gradient, thereby allowing preferential directional heat flow. A dual phase thermal diode consists of a junction between two phase change materials that have opposing temperature-dependent thermal conductivity trends, and whose performance (i.e., rectification ratio) is related to the ratio of the thermal conductivities of the different phases. In this work, a dual phase change diode with a rectification ratio of ~3.5 for an applied temperature bias of ~40 K is presented, which is among the highest-performing junction diodes based on phase change materials at the macroscale for near room temperature applications. The diode is composed of an aqueous solution of poly(N-isopropylacrylamide), a thermo-responsive polymer, and calcium chloride hexahydrate -- a solid-liquid phase change material. Experimental insights are provided into the contributions of different heat transfer mechanisms, conduction, and convection, and the effect of concentration of the thermo-responsive polymer.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Probing ethane phase changes in bead pack via high-field NMR spectroscopy

Phase equilibria analysis in two-phase systems requires discernment of the individual phases as well as the interfacial region. The phase behavior of fluids in constraint geometries have been studied through several techniques. High-Field Nuclear Magnetic Resonance (HF-NMR) can be used to detect fluid phases, i.e. gas, liquid, or supercritical fluid, in the bulk or under confinement. In solution-state HF-NMR, each phase exhibits a distinct chemical shift that correlates to the phase density. In turn, the emergence of multimodal in NMR spectra reveals the coexistence of multiple phases in fluid systems. Our results for ethane show that HF-NMR can enable tracking phase changes in the bulk, but also in macro-scale (10–100's μm in pore size) porous systems at various pressure and temperature conditions, even when the system us out of equilibrium. Finally, these results creates potential opportunities to investigate phase changes influenced by confinement in porous systems, though additional steps are necessary.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Phase change material-to-refrigerant heat exchangers: Experimental validation and uneven melting analysis

Thermal energy storage (TES) using phase change materials (PCMs) enables load shifting and reduces mismatches between the building's thermal demand and the heat pump (HP) system's thermal capacity. While most TES studies have focused on single-phase heat transfer fluids, PCM-to-refrigerant heat exchangers (PRHX), in which the refrigerant undergoes liquid-vapor phase change, remain largely underexplored. Here, to address this gap, this study systematically investigates a shell-and-tube PRHX operating as the condenser in an HP through experiments and simulations. A two-dimensional enthalpy-based finite-volume PRHX model was developed and validated against experimental data, including refrigerant and PCM temperature profiles, PRHX capacity, and system-level performance. Results show three characteristic stages: Stage I, the condenser temperature rapidly increases with PCM in the solid state absorbing sensible heat; Stage II, stable operation during PCM phase change; and Stage III, performance decline once part of the PCM becomes fully melted. Heat transfer analysis revealed that uneven PCM melting along the condenser length was driven primarily by variations in the refrigerant-side heat transfer coefficient, rather than local approach temperature differences. Further study demonstrated that minimizing refrigerant outlet subcooling led to more uniform PCM melting and extended Stages I and II by up to 89%. This paper provides a validated PRHX model, clarifies the mechanisms of uneven PCM melting, and highlights subcooling control as an effective strategy to improve TES performance in HP systems without requiring secondary loops.

Graphite matrix↗
DOE OSTI2023

Techno-Economic Analysis of Dynamic Building Envelopes Comprising Phase Change Materials and Switchable Insulations: Preprint

Integrating phase change materials (PCMs) in building envelopes is a recognized technique to reduce the space heating/cooling loads and provide load shedding and shifting capacity. However, PCM benefits have been found to reduce dramatically with increase in the insulation requirements. Dynamic building envelopes that can alter their thermal resistance based on the indoor and outdoor conditions can effectively harness free ambient heating/cooling, thereby greatly enhancing the benefits of the PCM-integrated envelope in managing thermal loads. In this study, we examine various combinations of PCMs and switchable insulations and compare their combined impact on heat flow through the building envelope. Using numerical analysis, we investigate the PCM- and switchable insulation-integrated building walls, calculate the potential energy saving benefits compared to the conventional static walls, and finally perform technoeconomic analysis to estimate the acceptable cost of the technology under various payback period scenarios.

dynamic building envelopes↗
DOE OSTI2023

Neuromorphic Photonics Based on Phase Change Materials

Neuromorphic photonics devices based on phase change materials (PCMs) and silicon photonics technology have emerged as promising solutions for addressing the limitations of traditional spiking neural networks in terms of scalability, response delay, and energy consumption. In this review, we provide a comprehensive analysis of various PCMs used in neuromorphic devices, comparing their optical properties and discussing their applications. We explore materials such as GST (Ge 2 Sb 2 Te 5 ), GeTe-Sb 2 Te 3 , GSST (Ge 2 Sb 2 Se 4 Te 1 ), Sb 2 S 3 /Sb 2 Se 3 , Sc 0.2 Sb 2 Te 3 (SST), and In 2 Se 3 , highlighting their advantages and challenges in terms of erasure power consumption, response rate, material lifetime, and on-chip insertion loss. By investigating the integration of different PCMs with silicon-based optoelectronics, this review aims to identify potential breakthroughs in computational performance and scalability of photonic spiking neural networks. Further research and development are essential to optimize these materials and overcome their limitations, paving the way for more efficient and high-performance photonic neuromorphic devices in artificial intelligence and high-performance computing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analytical Modeling of Metal Foam Composite Phase Change Materials (PCM) in Thermal Energy Storage Using Asymptotic Analysis

The use of phase change materials (PCMs) for thermal energy storage can release or absorb a significant amount of latent heat during the freezing or melting process, offering a higher energy storage density. One of the main drawbacks of PCMs is their low thermal conductivity, resulting in poor thermal performance. Recent research has attempted to enhance heat transfer and increase the thermal conductivity of PCMs, including the use of metal foams. However, modeling the metal foam composite PCM using conventional methods is computationally expensive. This paper proposes an asymptotic solution for a Stefan-like problem subject to a convective boundary for outward solidification in a hollow cylinder, capable of predicting the freeze-melt cycle of the metal foam composite PCM. Specifically, three temporal regimes and four spatial layers are considered in the asymptotic analysis for each phase change process. The thermal conductivity is calculated by a theoretical three-dimensional tetrakaidecahedron model, while other thermophysical properties are obtained using the method of volume averaging. The results are verified with numerical data and validated against experimental data in the literature. The presented analytical modeling framework could have the potential to be applied to other types of composite PCMs with considerably lower computational costs compared with conventional methods.

analytical model↗
DOE OSTI2020

System-Level Thermal Management and Reliability of Automotive Electronics: Goals and Opportunities Using Phase-Change Materials

Abstract Electronic packaging for automotive applications are at particular risk of thermomechanical failure due to the naturally harsh conditions it is exposed to. With the rise of electric and hybrid electric vehicles (EVs and HEVs), combined with a desire to miniaturize, the challenge of removing enough heat from electronic devices in automotive vehicles is evolving. This paper closely examines the new challenges in thermal management in various driving environments and aims to classify each existing cooling method in terms of performance. Particular focus is placed upon emerging solutions regarded to hold great potential, such as phase-change materials (PCMs). PCMs have been regarded for some time as a means of transferring heat quickly away from the region with the electronic components and are widely regarded as a possible means of carrying out cooling in large scale from small areas, because of their high latent heat of fusion, high specific heat, temperature stability, and small volume change during phase change, etc. They have already been utilized as a method of passive cooling in electronics in various ways, but their adoption in automotive power electronics, such as in traction inverters, has yet to be fulfilled. A brief discussion is made on some of the potential areas of application and challenges relating to more widespread adoption of PCMs, with reference to a case study using computational model of a commercially available power module used in automotive applications.

Engineering↗
DOE OSTI2025

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multipolymer Matrix

Additive manufacturing (AM) techniques to directly integrate phase change materials (PCMs) are of interest for efficient thermal energy storage (TES) architectures. Complex, high surface-to-volume ratio composites embedded with PCM can improve thermal management with reduced material waste for customizable device fabrication. Reducing feature sizes of TES-integrated heat exchangers using AM can increase heat transfer without thermal conductivity enhancement. Here, composite AM materials containing 60 wt% microencapsulated phase change materials (MEPCM) are fabricated using off-the-shelf printers at common speeds and resolutions. High MEPCM loading in filaments is achieved with powder extrusion using two polymers, thermoplastic-polyurethane (TPU) and polycaprolactone (PCL), that mediate flexibility and rigidity for effective extrusion and printing without filament fracture or buckling. Furthermore, with PCL and TPU at 20 wt% each and 60 wt% MEPCM (P 20 T 20 M 60 ), smooth, form-stable filaments are consistently printed. Powder-based extrusion displays negligible damaging effects on the MEPCM. Printed P 20 T 20 M 60 demonstrates 105 J/g of energy storage with no degradation through 250 thermal cycles, within 5% of the theoretical storage enthalpy. Combining PCL/TPU shows good interfacial adhesion between print layers and produces high surface area objects, like 15% gyroids, and dense, 100% infilled pucks. Prints are also scalable to a 900 cm 3 honeycomb heat exchanger with an estimated 9 Wh energy storage.

25 ENERGY STORAGE↗
DOE OSTI2026

Thermal property characterization of phase change materials in building applications: A systematic review of fundamentals, recent progress, and future directions

Phase change materials (PCMs) can reduce building peak loads and enable demand-responsive thermal energy storage (TES), but their deployment depends on reliable measurement and interpretation of thermal properties across laboratory, intermediate, and application scales. Here, this review systematically examines characterization methods, testing protocols, and recent advances for neat PCMs and PCM composites, emphasizing thermal conductivity, enthalpy-related properties (phase change temperature, latent heat, specific heat), and cycling stability. For thermal conductivity, we compare steady-state and transient techniques and note limitations when phase transition and contact resistance affect measurements. For enthalpy–temperature characterization, we discuss differential scanning calorimetry together with intermediate- and bulk-scale methods, including T-history, heat flow meter testing, and three-layer calorimetry (3LC), to generate application-relevant enthalpy–temperature profiles. Cycling stability is organized into four experimental families: thermoelectric–air, fully thermoelectric, water-bath, and in situ chamber approaches, with attention to separating reversible supercooling from true degradation such as phase segregation. We highlight emerging noncontact diagnostics, including infrared thermography and embedded sensing, for spatially resolved validation and multiscale interpretation. Finally, we review the growing use of AI and machine learning for property prediction, inverse characterization from experimental signals, and real-time state estimation in building-integrated TES. Key needs include harmonized protocols, interlaboratory benchmarking, uncertainty reporting, and metadata-rich datasets to accelerate reproducible PCM qualification for grid-flexible buildings.

AI↗