Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pattern Factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

The Advanced Low-Emissions Catalytic-Combustor Program: Phase I - Description and status

The Advanced Low-Emissions Catalytic-Combustor Program is an ongoing three-phase contract effort with the primary objective of evolving the technology required for incorporating catalytic combustors into advanced aircraft gas-turbine engines. Phase I is currently in progress. At the present time, analytical evaluation is being conducted on advanced catalytic-combustor concepts, including variable geometry, with their known inherent potential advantages of low-level pollutant emissions, widened combustion stability limits, and reduced pattern factor for longer turbine life. Phases II and III will consist of experimental evaluation of the most promising concepts.

Szaniszlo, A. J.↗

Low-pressure performance of annular, high-pressure (40 atm) high-temperature (2480 K) combustion system

Experimental tests were conducted to develop a combustion system for a 40 atmosphere pressure, 2480 K exhaust gas temperature, turbine cooling facility. The tests were conducted in an existing facility with a maximum pressure capability of 10 atmospheres and where inlet air temperatures as high as 894 K could be attained. Exhaust gas temperatures were as high as 2365 K. Combustion efficiences were about 100 percent over a fuel air ratio range of 0.016 to 0.056. Combustion efficiency decreased at leaner and richer ratios when the inlet air temperature was 589 K. Data are presented that show the effect of fuel air ratio and inlet air temperature on liner metal temperature. Isothermal system pressure loss as a function of diffuser inlet Mach number is also presented. Data included exhaust gas pattern factors; unburned hydrocarbon, carbon monoxide, and oxides of nitrogen emission index values; and smoke numbers.

Wear, J. D.↗

Performance of semi-transportation-cooled liner in high-temperature-rise combustors

Results from tests with the Lamilloy combustor liner are compared with results obtained from a conventionally designed, film cooled, step-louver liner. Operation of the Lamilloy liner with counterrotating swirl combustor fuel modules with mixing venturis was possible to a fuel-air ratio of 0.065 without obtaining excessive liner metal temperatures. At the 0.065 fuel-air condition the average liner metal temperature was 140 K and the maximum local temperature 280 K above the inlet air temperature. Combustion efficiency, pattern factor, and smoke data are discussed.

Wear, J. D.↗

Experimental study of the operating characteristics of premixing-prevaporizing fuel/air mixing passages

Fuel spray and air flow characteristics were determined using nonintrusive (optical) measurement techniques in a fuel preparation duct. A very detailed data set was obtained at high pressures (to 10 atm) and temperatures (to 750 K). The data will be used to calibrate an analytical model which will facilitate the design of a lean premixed prevaporized combustor. This combustor has potential for achieving low pollutant emissions and low levels of flame radiation and pattern factors conductive to improved durability and performance for a variety of fuels.

Rohy, D. A.↗

Aerothermal modeling, phase 1. Volume 2: Experimental data

The experimental test effort is discussed. The test data are presented. The compilation is divided into sets representing each of the 18 experimental configurations tested. A detailed description of each configuration, and plots of the temperature difference ratio parameter or pattern factor parameter calculated from the test data are also provided.

Kenworthy, M. J.↗

Preliminary investigation of a two-zone swirl flow combustor

The effect of full-annular swirling-flow on a flow-zone combustor design is investigated. Swirl flow angles of 25, 35, and 45 degrees were investigated in a combustor design envelope typical of those used in modern engines. The two-zone combustor had 24 pilot-zone fuel injectors and 24 main-fuel injectors located in the centerbody between the pilot and swirl passage. Combustor performance was determined at idle, and two parametric 589 K inlet temperature conditions. Combustor performance was highest with the 45 degree swirl vane design; at the idle condition, combustion efficiency was 99.5 percent. The 45 degree swirl vane also produced the lowest pattern factor of the three angles and showed a combustor lean blowout limit below a 0.001 fuel-air ratio. Combustor total pressure drop varied from a low of 4.6 percent for the 25 degree swirl to a high of 4.9 percent for the 45 degree swirl.

Biaglow, J. A.↗

Experimental investigation of the low NO/sub x vortex airblast annular combustor

A low oxides of nitrogen vortex airblast annular combustor was evaluated which has attained the goal of 1 gm NO2/kg fuel or less during operation. The experimental combustor test conditions were a nominal inlet-air temperature of 703 K, inlet total pressures between 0.52 to 0.83 MPa, and a constant inlet Mach number of 0.26. Exit temperature pattern factors for all test points were between 0.16 and 0.20 and exit swirl flow angles were 47 degrees at isothermal conditions and 23 degrees during combustion. Oxides of nitrogen did not exceed 1.05 gm NO2/kg fuel at the highest inlet pressure and exhaust temperature tested. Previous correlations have related NOx proportionally to the combustor inlet pressure raised to some exponent. In this experiment, a band of exponents between 0.5 and 1.0 resulted for fuel-air ratios from 0.023 to 0.027 and inlet pressures from 0.52 to 0.83 MPa.

Johnson, S. M.↗

Preliminary investigation of a two-zone swirl flow combustor

The effect of full-annular swirling-flow on a flow-zone combustor design is investigated. Swirl flow angles of 25, 35, and 45 degrees were investigated in a combustor design envelope typical of those used in modern engines. The two-zone combustor had 24 pilot-zone fuel injectors and 24 main-fuel injectors located in the centerbody between the pilot and swirl passage. Combustor performance was determined at idle, and two parametric 589 K inlet temperature conditions. Combustor performance was highest with the 45 degree swirl vane design; at the idle condition, combustion efficiency was 99.5 percent. The 45 degree swirl vane also produced the lowest pattern factor of the three angles and showed a combustor lean blowout limit below a 0.001 fuel-air ratio. Combustor total pressure drop varied from a low of 4.6 percent for the 25 degree swirl to a high of 4.9 percent for the 45 degree swirl. Previously announced in STAR as N84-22565

Biaglow, J. A.↗

Experimental investigation of the low NOx vortex airblast annular combustor

A low oxides of nitrogen vortex airblast annular combustor was evaluated which has attained the goal of 1 gm NO2/kg fuel or less during operation. The experimental combustor test conditions were a nominal inlet-air temperature of 703 K, inlet total pressures between 0.52 to 0.83 MPa, and a constant inlet Mach number of 0.26. Exit temperature pattern factors for all test points were between 0.16 and 0.20 and exit swirl flow angles were 47 degrees at isothermal conditions and 23 degrees during combustion. Oxides of nitrogen did not exceed 1.05 gm NO2/kg fuel at the highest inlet pressure and exhaust temperature tested. Previous correlations have related NOx proportionally to the combustor inlet pressure raised to some exponent. In this experiment, a band of exponents between 0.5 and 1.0 resulted for fuel-air ratios from 0.023 to 0.027 and inlet pressures from 0.52 to 0.83 MPa. Previously announced in STAR as N84-22567

Johnson, S. M.↗

Scattering from a microstrip patch

A solution to the problem of plane wave scattering by a rectangular microstrip patch on a grounded dielectric substrate is presented. The model does not include the microstrip feed, and thus doe not include the so-called 'antenna mode' component of the scattering. The solution begins by formulating an electric field integral equation for the surface current density on the microstrip patch. The integral equation is solved using the method of moments. Computed data for the patch radar cross section (RCS) is found to be in close agreement with measurements over a broad frequency range. The microstrip RCS versus frequency consists of a number of large peaks which are identified as impedance or pattern factor resonance peaks.

Newman, Edward H.↗

Combustion characteristics of gas turbine alternative fuels

An experimental investigation was conducted to obtain combustion performance values for specific heavyend, synthetic hydrocarbon fuels. A flame tube combustor modified to duplicate an advanced gas turbine engine combustor was used for the tests. Each fuel was tested at steady-state operating conditions over a range of mass flow rates, fuel-to-air mass ratio, and inlet air temperatures. The combustion pressure, as well as the hardware, were kept nearly constant over the program test phase. Test results were obtained in regards to geometric temperature pattern factors as a function of combustor wall temperatures, the combustion gas temperature, and the combustion emissions, both as affected by the mass flow rate and fuel-to-air ratio. The synthetic fuels were reacted in the combustor such that for most tests their performance was as good, if not better, than the baseline gasoline or diesel fuel tests. The only detrimental effects were that at high inlet air temperature conditions, fuel decomposition occurred in the fuel atomizing nozzle passages resulting in blockage. And the nitrogen oxide emissions were above EPA limits at low flow rate and high operating temperature conditions.

Rollbuhler, R. James↗

Fuel properties effect on the performance of a small high temperature rise combustor

The performance of an advanced small high temperature rise combustor was experimentally determined at NASA-Lewis. The combustor was designed to meet the requirements of advanced high temperature, high pressure ratio turboshaft engines. The combustor featured an advanced fuel injector and an advanced segmented liner design. The full size combustor was evaluated at power conditions ranging from idle to maximum power. The effect of broad fuel properties was studied by evaluating the combustor with three different fuels. The fuels used were JP-5, a blend of Diesel Fuel Marine/Home Heating Oil, and a blend of Suntec C/Home Heating Oil. The fuel properties effect on the performance of the combustion in terms of pattern factor, liner temperatures, and exhaust emissions are documented.

Acosta, Waldo A.↗

Fuel properties effect on the performance of a small high temperature rise combustor

The performance of an advanced small high temperature rise combustor was experimentally determined at NASA-Lewis. The combustor was designed to meet the requirements of advanced high temperature, high pressure ratio turboshaft engines. The combustor featured an advanced fuel injector and an advanced segmented liner design. The full size combustor was evaluated at power conditions ranging from idle to maximum power. The effect of broad fuel properties was studied by evaluating the combustor with three different fuels. The fuels used were JP-5, a blend of Diesel Fuel Marine/Home Heating Oil, and a blend of Suntec C/Home Heating Oil. The fuel properties effect on the performance of the combustion in terms of pattern factor, liner temperatures, and exhaust emissions are documented.

Acosta, Waldo A.↗

Three dimensional LDV flow measurements and theoretical investigation in a radial inflow turbine scroll

A two-color LDV system was used in the measurement of three orthogonal velocity components at 758 points located throughout the scroll and the unvaned portion of the nozzle of a radial inflow turbine scroll. The cold flow experimental results are presented for the velocity field at the scroll tongue. In addition, a total pressure loss of 3.5 percent for the scroll is revealed from the velocity measurements combined with the static pressure readings. Moreover, the measurement of the three normal stresses of the turbulence has showed that the flow is anisotropic. Furthermore, the mean velocity components are compared with a numerical solution of the potential flow field using the finite element technique. The theoretical prediction of the exit flow angle variation agrees well with the experimental results. This variation leads to a higher scroll pattern factor which can be avoided by controlling the scroll cross sectional area distribution.

Malak, Malak Fouad↗

Numerical simulation of a low-emission gas turbine combustor using KIVA-II

A modified version of the KIVA-II code was used to obtain a multidimensional numerical solution for the turbulent two-phase chemically reacting flows inside a staged turbine combustor (STC). The STC under consideration is equipped with an advanced airblast fuel nozzle and encompasses a fuel nozzle (FN), a rich-burn (RB) zone, a converging connecting pipe, a quick-quench (QQ) zone, a diverging connecting pipe, and a lean-combustion (LC) zone. The STC was divided into two subsystems, namely, FN/RB zone and QQ/LC zones, and the numerical solutions were obtained separately for each subsystem. Preliminary data characterize the major features of the flow and temperature fields inside the STC. Information on velocity, temperature, and some critical species in the FN/RB zone is presented. In the QQ/LC zones, formation of the co- and counter-rotating bulk flow and the sandwiched-ring-shaped temperature field can be clearly seen. The calculations of the mass-weighted standard deviation and the pattern factor of temperature indicated that the mixing performance of the STC is very promising.

Yang, S. L.↗

Compliant Metal Enhanced Convection Cooled Reverse-Flow Annular Combustor

A joint Army/NASA program was conducted to design, fabricate, and test an advanced, reverse-flow, small gas turbine combustor using a compliant metal enhanced (CME) convection wall cooling concept. The objectives of this effort were to develop a design method (basic design data base and analysis) for the CME cooling technique and tben demonstrate its application to an advanced cycle, small, reverse-flow combustor with 3000 F (1922 K) burner outlet temperature (BOT). The CME concept offers significant improvements in wall cooling effectiveness resulting in a large reduction in cooling air requirements. Therefore, more air is available for control of burner outlet temperature pattern in addition to the benefit of improved efficiency, reduced emissions, and smoke levels. Rig test results demonstrated the benefits and viability of the CME concept meeting or exceeding the aerothermal performance and liner wall temperature characteristics of similar lower temperature-rise combustors, achieving 0.15 pattern factor at 3000 F (1922 K) BOT, while utilizing approximately 80 percent less cooling air than conventional, film-cooled combustion systems.

Paskin, Marc D.↗

Numerical Study of Stratified Charge Combustion in Wave Rotors

A wave rotor may be used as a pressure-gain combustor effecting non-steady flow, and intermittent, confined combustion to enhance gas turbine engine performance. It will be more compact and probably lighter than an equivalent pressure-exchange wave rotor, yet will have similar thermodynamic and mechanical characteristics. Because the allowable turbine blade temperature limits overall fuel/air ratio to sub-flammable values, premixed stratification techniques are necessary to burn hydrocarbon fuels in small engines with compressor discharge temperature well below autoignition conditions. One-dimensional, unsteady numerical simulations of stratified-charge combustion are performed using an eddy-diffusivity turbulence model and a simple reaction model incorporating a flammability limit temperature. For good combustion efficiency, a stratification strategy is developed which concentrates fuel at the leading and trailing edges of the inlet port. Rotor and exhaust temperature profiles and performance predictions are presented at three representative operating conditions of the engine: full design load, 40% load, and idle. The results indicate that peak local gas temperatures will result in excessive temperatures within the rotor housing unless additional cooling methods are used. The rotor itself will have acceptable temperatures, but the pattern factor presented to the turbine may be of concern, depending on exhaust duct design and duct-rotor interaction.

Nalim, M. Razi↗

Active Combustion Control for Aircraft Gas Turbine Engines

Lean-burning combustors are susceptible to combustion instabilities. Additionally, due to non-uniformities in the fuel-air mixing and in the combustion process, there typically exist hot areas in the combustor exit plane. These hot areas limit the operating temperature at the turbine inlet and thus constrain performance and efficiency. Finally, it is necessary to optimize the fuel-air ratio and flame temperature throughout the combustor to minimize the production of pollutants. In recent years, there has been considerable activity addressing Active Combustion Control. NASA Glenn Research Center's Active Combustion Control Technology effort aims to demonstrate active control in a realistic environment relevant to aircraft engines. Analysis and experiments are tied to aircraft gas turbine combustors. Considerable progress has been shown in demonstrating technologies for Combustion Instability Control, Pattern Factor Control, and Emissions Minimizing Control. Future plans are to advance the maturity of active combustion control technology to eventual demonstration in an engine environment.

DeLaat, John C.↗