Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Part quality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Advanced composite elevator for Boeing 727 aircraft, volume 2

Preliminary design activity consisted of developing and analyzing alternate design concepts and selecting the optimum elevator configuration. This included trade studies in which durability, inspectability, producibility, repairability, and customer acceptance were evaluated. Preliminary development efforts consisted of evaluating and selecting material, identifying ancillary structural development test requirements, and defining full scale ground and flight test requirements necessary to obtain Federal Aviation Administration (FAA) certification. After selection of the optimum elevator configuration, detail design was begun and included basic configuration design improvements resulting from manufacturing verification hardware, the ancillary test program, weight analysis, and structural analysis. Detail and assembly tools were designed and fabricated to support a full-scope production program, rather than a limited run. The producibility development programs were used to verify tooling approaches, fabrication processes, and inspection methods for the production mode. Quality parts were readily fabricated and assembled with a minimum rejection rate, using prior inspection methods.

Chovil, D. V.↗
NASA NTRS1991

Superplastic forming of Al-Li alloys for lightweight, low-cost structures

Superplastic forming of advanced aluminum alloys is being evaluated as an approach for fabricating low-cost, light-weight, cryogenic propellant tanks. Built-up structure concepts (with inherent reduced scrap rate) are under investigation to offset the additional raw material expenses incurred by using aluminum lithium alloys. This approach to fabrication offers the potential for significant improvements in both structural efficiency and overall manufacturing costs. Superplasticity is the ability of specially processed material to sustain very large forming strains without failure at elevated temperatures under controlled deformation conditions. It was demonstrated that superplastic forming technology can be used to fabricate complex structural components in a single operation and increase structural efficiency by as much as 60 percent compared to conventional configurations in skin-stiffened structures. Details involved in the application of this technology to commercial grade superplastic aluminum lithium material are presented. Included are identification of optimum forming parameters, development of forming procedures, and assessment of final part quality in terms of cavitation volume and thickness variation.

Hales, Stephen J.↗
NASA NTRS1996

In-situ Frequency Dependent Dielectric Sensing of Cure

With the expanding use of polymeric materials as composite matrices, adhesives, coatings and films, the need to develop low cost, automated fabrication processes to produce consistently high quality parts is critical. Essential to the development of reliable, automated, intelligent processing is the ability to continuously monitor the changing state of the polymeric resin in-situ in the fabrication tool. This final report discusses work done on developing dielectric sensing to monitor polymeric material cure and which provides a fundamental understanding of the underlying science for the use of frequency dependent dielectri sensors to monitor the cure process.

Kranbuehl, David E.↗
NASA NTRS1997

Advanced Technology Composite Fuselage - Manufacturing

The goal of Boeing's Advanced Technology Composite Aircraft Structures (ATCAS) program is to develop the technology required for cost-and weight-efficient use of composite materials in transport fuselage structure. Carbon fiber reinforced epoxy was chosen for fuselage skins and stiffening elements, and for passenger and cargo floor structures. The automated fiber placement (AFP) process was selected for fabrication of stringer-stiffened and sandwich skin panels. Circumferential and window frames were braided and resin transfer molded (RTM'd). Pultrusion was selected for fabrication of floor beams and constant-section stiffening elements. Drape forming was chosen for stringers and other stiffening elements cocured to skin structures. Significant process development efforts included AFP, braiding, RTM, autoclave cure, and core blanket fabrication for both sandwich and stiffened-skin structure. Outer-mold-line and inner-mold-line tooling was developed for sandwich structures and stiffened-skin structure. The effect of design details, process control and tool design on repeatable, dimensionally stable, structure for low cost barrel assembly was assessed. Subcomponent panels representative of crown, keel, and side quadrant panels were fabricated to assess scale-up effects and manufacturing anomalies for full-scale structures. Manufacturing database including time studies, part quality, and manufacturing plans were generated to support the development of designs and analytical models to access cost, structural performance, and dimensional tolerance.

Wilden, K. S.↗
NASA NTRS1997

In-Situ Cure Monitoring of the Immidization Reaction of PMR-15

Glass fiber reinforced polymer composites are becoming widely used in industry. With this increase in production, an in-situ method of quality control for the curing of the polymer is desirable. This would allow for the production of high-quality parts having more uniform properties.' Recently, in-situ fiber optic monitoring of polymer curing has primarily focused on epoxy resins and has been performed by Raman or fluorescence methods. In addition, some infrared (IR) investigations have been performed using transmission or ATR cells. An alternate IR approach involves using optical fibers as a sensor by utilizing evanescent wave spectroscopy.

Cossins, Sheryl↗
NASA NTRS1997

Electron Beam Cured Epoxy Resin Composites for High Temperature Applications

Electron beam curing of Polymer Matrix Composites (PMC's) is a nonthermal, nonautoclave curing process that has been demonstrated to be a cost effective and advantageous alternative to conventional thermal curing. Advantages of electron beam curing include: reduced manufacturing costs; significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; and improvement in material handling. In 1994 a Cooperative Research and Development Agreement (CRADA), sponsored by the Department of Energy Defense Programs and 10 industrial partners, was established to advance the electron beam curing of PMC technology. Over the last several years a significant amount of effort within the CRADA has been devoted to the development and optimization of resin systems and PMCs that match the performance of thermal cured composites. This highly successful materials development effort has resulted in a board family of high performance, electron beam curable cationic epoxy resin systems possessing a wide range of excellent processing and property profiles. Hundreds of resin systems, both toughened and untoughened, offering unlimited formulation and processing flexibility have been developed and evaluated in the CRADA program.

Janke, Christopher J.↗
NASA NTRS1972

HELIOS Critical Design Review: Quality Assurance

The following is an account of the activities of the Quality Assurance (QA) department of the project management office highlighting some of the ways in which it controls QA of the subcontractors on one hand and reports on Quality to GfW (Gesellschaft fur Weltraumforschung) on the other hand. The basic document prepared by MBB (Messerschmitt-Bolkow-Blohm) for QA activities is 1. The QA plan based on GfW 002. The QA department is responsible moreover for monitoring and making decisions about the quality of parts and materials and the governing document for this activity is 2. The Parts and Materials Control Plan based on GfW 001 - the reliability program provisions, as well as GfW 002. A brief survey of the contents of the QA Plan is shown. It should be noted that QA activity dealing with parts procurement is partially covered in a separate presentation entitled "Hi-Rel Parts". Supplementary quality documents are shown.

Benoehr, H. C.↗
NASA NTRS2003

Determination of Significant Composite Processing Factors by Designed Experiment (MSFC Center Director's Discretionary Fund)

To determie composite material properties' effects from porcessing variables, a 3 factorial designed experiment with two replicates was conducted. The factors were cure method (oven versus autoclave), layup (hand versus tape-laying machine), and thickness (8 versus 52 ply). Four material systems were tested: AS4/3501-6, IM7/8551-7, IM7/F655 bismaleimide (BMI), and shear tests on IM7/F584. Material properties were G(sub 12), v(sub 12), E(sub 1c) and E(sub 2c). Since the samples were necessarily nonstandard, strengths, though recorded, cannot be considered valid. Void content was also compared. Autoclave curing helped material properties for the low modulus fiber material but showed little benefit for higher stiffness fibers. The number of plies was very important for epoxy composites but not for the BMI. E(sub 1) was generally unaffected by any factor. Particularly high void content did correlate to reduced properties. Autoclave curing reduced void content over oven curiing but a moderate amount of voids, less than 1 percent void content, didnot correlate with material properties. Oven cures and hand layups can produce high-quality parts. Part thickness of epoxy composites is important, though cure optimization may improve performance. Significant variations can be caused by processing and it is important that test coupons always reflect the layup and processes of the final part.

Finckenor, J. L.↗
NASA NTRS2015

Detection of CFRP Composite Manufacturing Defects Using a Guided Wave Approach

NASA Langley Research Center is investigating a guided-wave based defect detection technique for as-fabricated carbon fiber reinforced polymer (CFRP) composites. This technique will be extended to perform in-process cure monitoring, defect detection and size determination, and ultimately a closed-loop process control to maximize composite part quality and consistency. The overall objective of this work is to determine the capability and limitations of the proposed defect detection technique, as well as the number and types of sensors needed to identify the size, type, and location of the predominant types of manufacturing defects associated with laminate layup and cure. This includes, porosity, gaps, overlaps, through-the-thickness fiber waviness, and in-plane fiber waviness. The present study focuses on detection of the porosity formed from variations in the matrix curing process, and on local overlaps intentionally introduced during layup of the prepreg. By terminating the cycle prematurely, three 24-ply unidirectional composite panels were manufactured such that each subsequent panel had a higher final degree of cure, and lower level of porosity. It was demonstrated that the group velocity, normal to the fiber direction, of a guided wave mode increased by 5.52 percent from the first panel to the second panel and 1.26 percent from the second panel to the third panel. Therefore, group velocity was utilized as a metric for degree of cure and porosity measurements. A fully non-contact guided wave hybrid system composed of an air-coupled transducer and a laser Doppler vibrometer (LDV) was used for the detection and size determination of an overlap By transforming the plate response from the time-space domain to the frequency-wavenumber domain, the total wavefield was then separated into the incident and backscatter waves. The overlap region was accurately imaged by using a zero-lag cross-correlation (ZLCC) imaging condition, implying the incident and backscattered waves are in phase over the overlap boundaries.

Hudson, Tyler B.↗
NASA NTRS2016

Development of a Fully Automated Guided Wave System for In-Process Cure Monitoring of CFRP Composite Laminates

A guided wave-based in-process cure monitoring technique for carbon fiber reinforced polymer (CFRP) composites was investigated at NASA Langley Research Center. A key cure transition point (vitrification) was identified and the degree of cure was monitored using metrics such as amplitude and time of arrival (TOA) of guided waves. Using an automated system preliminarily developed in this work, high-temperature piezoelectric transducers were utilized to interrogate a twenty-four ply unidirectional composite panel fabricated from Hexcel (Registered Trademark) IM7/8552 prepreg during cure. It was shown that the amplitude of the guided wave increased sharply around vitrification and the TOA curve possessed an inverse relationship with degree of cure. The work is a first step in demonstrating the feasibility of transitioning the technique to perform in-process cure monitoring in an autoclave, defect detection during cure, and ultimately a closed-loop process control to maximize composite part quality and consistency.

Hudson, Tyler B.↗
NASA NTRS2019

TPSAS-NF1676L-32791-DND

Accelerate adoption of 3D printing in aerospace by investigating issues involving part quality, material compatibility, and hierarchical structures.

John M Gardner↗
NASA NTRSDate not supplied

Assured Performance of Additively Manufactured and Composite Parts through Embedded Sensing and Life Cycle Monitoring: An Enabler for in-Space Use

Lightweight composites have a range of applications in aerospace where operational costs and mission (payload) capabilities depend significantly on component weight. Additive manufacturing of the composite components expands the design and production space allowing for complex part geometries. A limiting factor to the utilization of the composites in high value applications, such as aerospace generally, and particularly for in-space applications, is the ability to determine the part quality both at the time of production as well as through the lifetime of the component. Work on monitoring the performance of additively manufactured and autoclaved composites that encompasses the design and manufacturing as well as use in operational environments will be discussed. Optimization of the component design for manufacturability, the use of process monitoring sensors during the component build as well as embedding of carbon nanotube yarn based structural sensors will be described.

Additive Manufacturing↗
NASA NTRS2021

A Study of Lessons and Experiences of NASA Centers in the Use of Commercial Off the Shelf (COTS) Electronics

The NASA Engineering and Safety Center (NESC) sponsored a Technical Assessment relating to the utilization of commercial-off-the-shelf (COTS) electrical, electronic, and electromechanical (EEE) parts in spaceflight systems at NASA Centers. The assessment had two primary goals. The first was to capture each NASA Centers’ current practices, best practices, lessons learned and Center-proposed recommendations on the use of COTS EEE parts and assemblies in critical ground support equipment (GSE). The second was to provide recommendations on the use of COTS, including a set of current best practices based on the Centers’ current and best practices and the NESC team’s discussions. One key achievement made by the assessment team was the characterization of the term Industry Leading Parts Manufacturers (ILPMs) as parts manufacturer with high volume automatic production facilities and which can provide documented proof of the technology, process and product qualification, and its implementation of the best practices for “zero defects” for parts quality, reliability and workmanship. The assessment concluded with numerous findings, takeaways and recommendations that will be discussed during this presentation.

commercial↗
NASA NTRS2003

Torque Limit for Bolted Joint For Composites: Experimentation - Part B

Today, aerospace quality composite parts are generally made from either a unidirectional tape or a fabric prepreg form depending on the application. The matrix material, typically epoxy because of it dimensional stability, is pre-impregnated onto the fibers to ensure uniform distribution. Both of these composite forms are finding themselves used in applications where a joint is required. Two widely used joint methods are the classic mechanically fastened joint, and the contemporary bonded joint; however, the mechanically fastened joint is most commonly used by design engineers. A major portion of the research up-to-date about bolted composite joints has dealt with the inplane static load capacity. This work has helped to spawn standards dealing with filled-hole static joint strength. Other research has clearly shown that the clamp-up load in the mechanical fastener significantly affects the joint strength in a beneficial manner by reducing the bearing strength dependence of the composite laminate. One author reported a maximum increase in joint strength of 28%. This finding has helped to improve the reliability and efficiency of the joint in a composite structure.

Kostreva, Kristian M.↗
NASA NTRS1976

An analytical method for ride quality of flexible airplanes

A new and easily used state variable method of aircraft ride quality analysis is developed and its use is illustrated by a numerical example using DC-8 airplane equations of motion. The method readily allows any type of stability augmentation system to be included for good handling qualities. As part of the ride quality analysis, a particularly powerful method of specifying and achieving all roots of a desired closed-loop characteristic equation by use of full state variable feedback is described and applied to the DC-8 example.

Swaim, R. L.↗
NASA NTRS2017

Initiatives to Improve Quality of Additively Manufactured Parts

NASA is providing leadership in an international effort linking government and industry resources to speed adoption of additive manufactured (AM) parts. Participants include government agencies (NASA, USAF, NIST, FAA), industry (commercial aerospace, NDE manufacturers, AM equipment manufacturers), standards organizations and academia. NASA is also partnering with its international space exploration organizations such as ESA and JAXA. NDT is identified as a universal need for all aspects of additive manufacturing.

Waller, Jess↗
NASA NTRS2009

Compliance with Aerospace Quality Assurance Standard AS9100

The contents include: 1) United States Federal Acquisition Regulations (FAR) Part 46, Quality Assurance; 2) NASA Quality Roadmap; 3) AS9003 Inspection and Test Quality Management System; 4) Government Oversight Responsibilities; and 5) Third Party vs Second Party Oversight.

Hughitt, Brian↗
NASA NTRS1984

The vectorization of a ray tracing program for image generation

Ray tracing is a widely used method for producing realistic computer generated images. Ray tracing involves firing an imaginary ray from a view point, through a point on an image plane, into a three dimensional scene. The intersections of the ray with the objects in the scene determines what is visible at the point on the image plane. This process must be repeated many times, once for each point (commonly called a pixel) in the image plane. A typical image contains more than a million pixels making this process computationally expensive. A traditional ray tracing program processes one ray at a time. In such a serial approach, as much as ninety percent of the execution time is spent computing the intersection of a ray with the surface in the scene. With the CYBER 205, many rays can be intersected with all the bodies im the scene with a single series of vector operations. Vectorization of this intersection process results in large decreases in computation time. The CADLAB's interest in ray tracing stems from the need to produce realistic images of mechanical parts. A high quality image of a part during the design process can increase the productivity of the designer by helping him visualize the results of his work. To be useful in the design process, these images must be produced in a reasonable amount of time. This discussion will explain how the ray tracing process was vectorized and gives examples of the images obtained.

Plunkett, D. J.↗