Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE GAGES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Preliminary results of the first static calibration of the RSRA helicopter active-isolator rotor balance system

The helicopter version of the Rotor Systems Research Aircraft (RSRA) is designed to make simultaneous measurements of all rotor forces and moments in flight analogous to a wind tunnel balance. Loads are measured by a combination of load cells, strain gages, and hydropneumatic active isolators which use pressure gages to measure loads. Complete evaluation of system performance required calibration of the rotor force and moment measuring system when installed in the aircraft. Measurement system responses to rotor loads obtained during the first static calibration of the RSRA helicopter are plotted and discussed. Plots of the raw transducer data are included.

Acree, C. W., Jr.↗

Airbreathing Laser Propulsion Experiments with 1 {mu}m Terawatt Pharos III Laser: Part 1

This basic research study examines the physics of airbreathing laser propulsion at the extreme flux range of 1-2x10{sup 11} W/cm{sup 2}--within the air breakdown threshold for l {mu}m radiation--using the terawatt PHAROS III neodymium-glass pulsed laser. Six different experimental setups were tested using a 34 mm line focus with 66 {mu}m focal waist, positioned near the flat impulse surface. The first campaign investigated impulse generation with the beam oriented almost normal to the target surface, with energies ranging from 23 to 376 J, and pulses of 5 to 30 ns FWHM. Air breakdown/ plasma dynamics were diagnosed with GOI cameras and color photography. Laser generated impulse was quantified with both vertical pendulums and piezoelectric pressure transducers using the standard performance metric, C{sub M}--the momentum coupling coefficient. Part 1 of this 2-part paper covers Campaign no. 1 results including laser plasma diagnostics, pressure gage and vertical pendulum data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Miniature telemetry system accurately measures pressure

Miniature, low power, telemetry system that can be used with commercially available strain gage pressure transducers accurately measures pressure with a small implantable pressure cell and transmitter. The system has been used to date only with pressure transducers, but the circuit is equally applicable to any measurement using a strain gage sensor.

Fryer, T. B.↗

Instrumentation for measuring the dynamic pressure on rotating compressor blades

To establish the capability for measurement of oscillatory pressure on rotating blades, miniature fast response semiconductor strain gage pressure transducers (2mm x 0.33mm) were mounted in several configurations on thin titanium and steel compressor blades and subjected to pressure cycles from 1 to 310 kPa during static tests and spin tests. Static test conditions included 20 C to 150 C, 0 to 3000 tensile microstrain, -1000 to +1000 bending microstrain and + or - 650G vibration. The spin test conditions included 20 C to 82 C at 0 to 90,000G. Durability was excellent. Pressure transducer sensitivity changed by only a few percent over this range of environmental conditions. Noise signal due to oscillatory acceleration normal to the diaphragm was acceptable (0.33Pa/G). Noise signal due to oscillatory strain was acceptable (0.5 Pa/microstrain) when the transducer was mounted on a 0.05mm rubber pad, with a total buildup of 0.38mm on the measure surface. Back mounting or partial recessing to eliminate buildup, increased the strain effect to 1.2 Pa/microstrain. Flush mounting within the blade to eliminate buildup reduced the strain effect, but required development of a special transducer shape. This transducer was not available in time for spin tests. Unpredictable zero drift + or - 14 kPa ruled out the use of these mounting arrangements for accurate steady-state (D.C.) measurements on rotating blades. The two best configurations fully developed and spin tested were then successfully applied in the NAS3-20606 rotating fan flutter program for quantitative measurement of oscillatory pressure amplitudes.

Grant, H. P.↗

Numerical analysis of the first static calibration of the RSRA helicopter active-isolator rotor balance system

The helicopter version of the Rotor Systems Research Aircraft (RSRA) is designed to make simultaneous measurements of all rotor forces and moments in a manner analogous to a wind-tunnel balance. Loads are measured by a combination of load cells, strain gages, and hydropneumatic active isolators with built-in pressure gages. Complete evaluation of system performance requires calibration of the rotor force- and moment-measurement system when installed in the aircraft. Derivations of calibration corrections for various combinations of calibration data are discussed.

Acree, C. W., Jr.↗

Static calibration of the RSRA active-isolator rotor balance system

The Rotor Systems Research Aircraft (RSRA) active-isolator system is designed to reduce rotor vibrations transmitted to the airframe and to simultaneously measure all six forces and moments generated by the rotor. These loads are measured by using a combination of load cells, strain gages, and hydropneumatic active isolators with built-in pressure gages. The first static calibration of the complete active-isolator rotor balance system was performed in l983 to verify its load-measurement capabilities. Analysis of the data included the use of multiple linear regressions to determine calibration matrices for different data sets and a hysteresis-removal algorithm to estimate in-flight measurement errors. Results showed that the active-isolator system can fulfill most performance predictions. The results also suggested several possible improvements to the system.

Acree, C. W., Jr.↗

Unsteady loads measurements in a generic high speed engine model by means of recessed transducers

Results are presented from measurements of unsteady loads during performance tests of a generic high-speed engine model, which were made using high-frequency pressure gages installed in existing calorimeter ports of the engine model and recessed into the interior wall surface in order to reduce thermal flux to the gage diaphragm. In was found that the boundary layer pressure spectra at the model wall start to deviate from their flat plate counterpart at a short distance into the model inlet, which suggests the contributions to the spectra from the shock/boundary layer interaction. It was also found that significant levels of combustion noise propagate up through the subsonic portion of the boundary layer well into the inlet region. At the condition of an unstart, the combustion noise apparently couples with the acoustic modes of the model to cause acoustic 'hot spots' well upstream of the combustor.

Parrott, Tony L.↗

A Whitham-Theory Sonic-Boom Analysis of the TU-144 Aircraft at a Mach Number of 2.2

NASA became interested in the Tu- 144 aircraft when it was offered for use as a "flying testbed" to study operating characteristics of a supersonic-cruise commercial airplane. In addition to the other operational tests being conducted on the Tu- 144 aircraft, it was proposed that two sets of sonic-boom pressure signature measurements be made. One set of tests would consist of ground-level pressure measurements. The second set would be measurements of pressures under the Tu- 144 aircraft in cruise. Pressure gages would be required for this second set of tests: measuring ambient and differential pressures in the flow field of a Tu-144 cruising at supersonic speeds. The range of these gages had to be determined well in advance of the scheduled flights so that they could be installed and calibrated.

Robert J Mack↗

A hot-film static-pressure probe

The procedure described involves calibrating the probe in the gas of interest over the range of temperatures and pressures anticipated in the wind-tunnel tests and then applying the calibration to reduce the data from those tests. Pressure readings from two probes, one having two hot-film sensors and an internal sonic orifice and the other connected to a conventional pressure gage, are recorded for several Reynolds numbers and compared. The conventional static-pressure probe with a pair of hot-film sensors and an interior sonic orifice is shown to provide the means of surveying flowfields in hypersonic flow at a rapid rate and with an accuracy of better than + or - 10%.

Ashby, G. C., Jr.↗

Static test of an ultralight airplane

This paper describes all of the work necessary to perform the static test of an ultralight airplane. A steel reaction gantry was designed first, then all of the loading whiffletrees, the hydraulic actuation system, and instrumentation systems were designed. Loads and stress analyses were performed on the airplane and the gantry and whiffletrees. Components tested to date are: tubing samples, cables, and two-by-four whiffletrees. A hydraulic system consisting of a 3000-psi hand pump, 10,000-pound actuator, pressure gage and lines, and a Barksdale valve are described. Load cell calibration and pressure indicator calibration procedures are also described. A description of the strain and deflection measurement system is included. Preliminary data obtained to date are compared to the analytical predictions.

Smith, H. W.↗

Vacuum gage calibration system for 10 to the minus 8th power to 10 torr

Calibration system consists of a gas source, a source pressure gage, source volume, transfer volume and test chamber, plus appropriate piping, valves and vacuum source. It has been modified to cover as broad a range as possible while still providing accuracy and convenience.

Holanda, R.↗

Steady- and unsteady-pressure measurements on a supercritical-wing model with oscillating control surfaces at subsonic and transonic speeds

A high aspect ratio supercritical wing with oscillating control surfaces is described. The semispan wing model was instrumented with 252 static pressure orifices and 164 in situ dynamic pressure gages for studying the effects of control surface position and sinusoidal motion on steady and unsteady pressures. Results from the present test (the third in a series of tests on this model) were obtained in the Langley Transonic Dynamics Tunnel at Mach numbers of 0.60, 0.78, and 0.86 and are presented in tabular form.

Sandford, M. C.↗

Transonic steady- and unsteady-pressure measurements on a high-aspect-ratio supercritical-wing model with oscillating control surfaces

A supercritical wing with an aspect ratio of 10.76 and with two trailing-edge oscillating control surfaces is described. The semispan wing is instrumented with 252 static orifices and 164 in situ dynamic-pressure gages for studying the effects of control-surface position and motion on steady- and unsteady-pressures at transonic speeds. Results from initial tests conducted in the Langley Transonic Dynamics Tunnel at two Reynolds numbers are presented in tabular form.

Sandford, M. C.↗

Measuring unsteady pressure on rotating compressor blades

The capability for accurate measurement of unsteady pressure on the surface of compressor and fan blades during engine operation was established. Tests were run on miniature semiconductor strain gage pressure transducers mounted in several arrangements. Both surface mountings and recessed flush mountings were tested. Test parameters included mounting arrangement, blade material, temperature, local strain in the blade, acceleration normal to the transducer diaphragm, centripetal acceleration, and pressure. Test results showed no failures of transducers or mountings and indicated an uncertainty of unsteady pressure measurement of approximately + or - 6%, plus 0.1 kPa for a typical application.

Englund, D. R.↗

Model 360 rotor test at DNW - Review of performance and blade airload data

The results of tests on a pressure gage instrumented model rotor, performed at the Duits Nederlandse Windtunnel (DNW) are discussed. The rotor, which was a 1/5 scale model of the Boeing Vertol model 360 rotor, was tested both in the anechoic open jet test section, and in the 8 x 6 m closed test section of the DNW. The wind tunnel, the blade instrumentation, and the test conditions are described, and data on rotor performance, blade and control loads, and blade-pressure and acoustic measurements are presented.

Dadone, Leo↗

High Voltage Test-Stand Research Done on ICRF Antenna Elements of the High-Harmonic Fast-Wave System of NSTX

The twelve-strap high-harmonic fast-wave (HHFW) antenna on NSTX has exhibited a high-voltage standoff around 25 kV during previous experimental campaigns; this standoff needs to be improved for increased power coupling. During the recent NSTX-U upgrade period, a test-stand was set up with two antenna straps along with Faraday screens for testing purposes. Using a diagnostic suite consisting of a fast camera, a residual gas analyzer, a pressure gage, high-voltage probes, and an infrared camera, several interesting discoveries were made, leading to possible improvements of the antenna RF voltage operation level. First, arcing was observed outside the Faraday shields towards the low-voltage ("grounded") end of the straps (faraday shield box ends); this arcing was successfully eliminated by installing an additional grounding point between the Faraday shield box and the vessel wall. Second, considerable outgassing was observed during the RF pulse and the amount of outgassing was found to decrease with increasing RF power, possibly indicative of multipacting. Finally, infrared camera measurements of heating on the Faraday shield assembly suggest that the return currents on the Faraday shield box are highly localized at the box sides and possibly account for the pressure increase observed. Computations of these RF currents using Microwave Studio show qualitative agreement with the heated regions. New grounding points between the antenna box and the vessel have been implemented in NSTX-U, where future tests will be done to determine if the high-voltage standoff has improved. Further antenna improvements will be sought through future experiments on the test stand.

Perkins, R. J.↗