Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATINUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

High-Temperature RF Transmission Loss Characteristics of Platinum–Inconel 600 and Platinum–304 Steel Interconnects

Radio frequency (RF) transmission losses that occur at electronic interconnects is currently an important limitation of wireless sensors and other electronic device packages that must operate in high-temperature environments. Herein, in-situ RF transmission losses were measured for two types of interconnects: platinum (Pt) wire bonded to an Inconel 600 coaxial cable; and Pt-wire bonded to a block of 304 steel. Heating the Pt wire/Inconel interconnects at 800 °C for up to 200 hours were found to be very stable with no measurable transmission losses. In contrast, Pt wire/304 steel block interconnects examined over similar test periods at 800 °C exhibited gradual increases in transmission losses leveling off at 10, 38 and 85 mdB at 400 MHz, 700 MHz, and 1 GHz, respectively. Increasing the test temperature to 900 °C caused further elevated transmission losses of 30, 70 and 108 mdB at the same reported frequencies. By comparison, temperature cycling of the Pt wire/304 steel interconnects between room temperature and 900 °C was found to cause more significant degradation. In particular, four thermal cycles from room temperature to 900 °C resulted in losses of 75, 271, and 482 mdB at the same reported frequencies. Parabolic oxidation relative to the RF skin depth in the 304 steel block at the tested frequencies are discussed as possible reasons for the transmission losses during the isothermal soaks, whereas interconnect degradation due to differences in thermal expansion between Pt and 304 steel are primarily responsible for transmission losses caused by high temperature cycling.

304 steel↗

Fuel cell performance of palladium-platinum core-shell electrocatalysts synthesized in gram-scale batches

This article presents the performance of palladium-platinum core-shell catalysts (Pt/Pd/C) for oxygen reduction synthesized in gram-scale batches in both liquid cells and polymer-electrolyte membrane fuel cells. Core-shell catalyst synthesis and characterization, ink fabrication, and cell assembly details are discussed. The Pt mass activity of the Pt/Pd core-shell catalyst was 0.95 A mg –1 at 0.9 V measured in liquid cells (0.1 M HClO4), which was 4.8 times higher than a commercial Pt/C catalyst. The performances of Pt/Pd/C and Pt/C in large single cells (315 cm 2 ) were assessed under various operating conditions. The core-shell catalyst showed consistently higher performance than commercial Pt/C in fuel cell testing. A 20–60 mV improvement across the whole current density range was observed on air. Sensitivities to temperature, humidity, and gas composition were also investigated and the core-shell catalyst showed a consistent benefit over Pt under all conditions. However, the 4.8 times activity enhancement predicated by liquid cell measurements was not fully realized in fuel cells.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Thermally Stable and Regenerable Platinum–Tin Clusters for Propane Dehydrogenation Prepared by Atom Trapping on Ceria

Abstract Ceria (CeO 2 ) supports are unique in their ability to trap ionic platinum (Pt), providing exceptional stability for isolated single atoms of Pt. The reactivity and stability of single‐atom Pt species was explored for the industrially important light alkane dehydrogenation reaction. The single‐atom Pt/CeO 2 catalysts are stable during propane dehydrogenation, but are not selective for propylene. DFT calculations show strong adsorption of the olefin produced, leading to further unwanted reactions. In contrast, when tin (Sn) is added to CeO 2 , the single‐atom Pt catalyst undergoes an activation phase where it transforms into Pt–Sn clusters under reaction conditions. Formation of small Pt–Sn clusters allows the catalyst to achieve high selectivity towards propylene because of facile desorption of the product. The CeO 2 ‐supported Pt–Sn clusters are very stable, even during extended reaction at 680 °C. Coke formation is almost completely suppressed by adding water vapor to the feed. Furthermore, upon oxidation the Pt–Sn clusters readily revert to the atomically dispersed species on CeO 2 , making Pt–Sn/CeO 2 a fully regenerable catalyst.

Xiong, Haifeng↗

The Priority and Challenge of High-Power Performance of Low-Platinum Proton-Exchange Membrane Fuel Cells [The Priority and Challenge of High-Power Performance of Low-Platinum PEMFCs]

Substantial progress has been made in reducing proton-exchange-membrane fuel cell (PEMFC) cathode platinum loadings from 0.4-0.8 mg Pt /cm 2 to about 0.1 mg Pt /cm 2 . However, at this level of cathode Pt loading, large performance loss is observed at high-current density (>1 A/cm 2 ), preventing a reduction in the overall stack cost. This next developmental step is being limited by the presence of a resistance term exhibited at these lower Pt loadings and apparently due to a phenomenon at or near the catalyst surface. This issue can be addressed through the design of catalysts with high and stable Pt dispersion as well as through development and implementation of ionomers designed to interact with Pt in a way that does not constrain oxygen reduction reaction rates. Here, extrapolating from progress made in past decades, we are optimistic that the concerted efforts of materials and electrode designers can resolve this issue, thus enabling a large step towards mass-market-affordable fuel cell vehicles.

08 HYDROGEN↗

Spot the difference: hydrogen adsorption and dissociation on unsupported platinum and platinum-coated transition metal carbides

Hydrogenation reactions are involved in several processes in heterogeneous catalysis. Platinum is the best-known catalyst; however, there are limitations to its practical use. Therefore, it is necessary to explore alternative materials and transition metal carbides (TMCs) have emerged as potential candidates. We explore the possibility of using cheap TMCs as supports for a Pt monolayer, aiming to reduce the amount of the noble metal in the catalyst without a significant loss of its activity towards H 2 dissociation. Hence, analyzing H 2 dissociation from a fundamental point of view is a necessary step towards a further practical catalyst. By means of periodic DFT calculations, we analyze H 2 adsorption and dissociation on Pt/β-Mo 2 C and Pt/α-WC surfaces, as a function of hydrogen surface coverage ( Θ H ), resembling a more realistic model of a catalyst. H 2 dissociation rates were analyzed as a function of the reaction temperature. Overall, the results show that Pt/C-WC and Pt/Mo-Mo 2 C have a Pt-like behavior for H 2 dissociation at Θ H > 1/2 ML. At a particular temperature of 298 K, Pt/C-WC and Pt/Mo-Mo2C have low energy barriers for H 2 * → 2H* (0.13 and 0.11 eV, respectively), close to the value of Pt (0.06 eV). For the highest coverage, i.e. Θ H = 1, Pt/C-WC has a lower activation energy and a higher reaction rate than Pt. Finally, the H 2 dissociation rate is higher in Pt/Mo-Mo 2 C than in Pt when increasing the temperature above 298 K. Our results put Pt/C-WC and Pt/Mo-Mo 2 C under the spotlight as potential catalysts for H 2 dissociation, with a similar performance to Pt, paving the way for further experimental and/or theoretical studies, addressing the capability of Pt/TMC as practical catalysts in hydrogenation reactions.

36 MATERIALS SCIENCE↗

Platinum- and platinum alloy-coated palladium and palladium alloy particles and uses thereof

The present invention relates to particle and nanoparticle composites useful as oxygen-reduction electrocatalysts. The particle composites are composed of a palladium or palladium-alloy particle or nanoparticle substrate coated with an atomic submonolayer, monolayer, bilayer, or trilayer of zerovalent platinum atoms. The invention also relates to a catalyst and a fuel cell containing the particle or nanoparticle composites of the invention. The invention additionally includes methods for oxygen reduction and production of electrical energy by using the particle and nanoparticle composites of the invention.

36 MATERIALS SCIENCE↗

Recent Advances in Platinum Monolayer Electrocatalysts for Oxygen Reduction Reaction: Scale-up Synthesis Structure and Activity of Pt Shells on Pd Cores

We have established a scale-up synthesis method to produce gram-quantities of Pt monolayer electrocatalysts. The core-shell structure of the Pt/Pd/C electrocatalyst has been verified using the HAADF-STEM Z-contrast images, STEM/EELS, and STEM/EDS line profile analysis. The atomic structure of this electrocatalyst and formation of a Pt monolayer on Pd nanoparticle surfaces were examined using in situ EXAFS. The Pt mass activity of the Pt/Pd/C electrocatalyst for ORR is considerably higher than that of commercial Pt/C electrocatalysts. The results with Pt monolayer electrocatalysts may significantly impact science of electrocatalysis and fuel-cell technology, as they have demonstrated an exceptionally effective way of using Pt that can resolve problems of other approaches, including electrocatalysts inadequate activity and high Pt content.

30 DIRECT ENERGY CONVERSION↗

Electrocatalytic Hydrogenation of Phenol over Platinum and Rhodium: Unexpected Temperature Effects Resolved

Both electrocatalytic hydrogenation (ECH) and thermal hydrogenation (TH) of phenol by Pt and Rh show a roll-over in rate with increasing temperature without changing the principal reaction pathways. The negative effect of temperature for aqueous-phase phenol H2 and electrocatalytic hydrogenation on Pt and Rh is deduced to be due to the unexpected buildup of dehydrogenated phenol adsorbates, which block active sites. Rates of ECH and TH increase similarly with increasing hydrogen chemical potential whether induced by applied potential or H2 pressure, both via increasing H coverage, and indirectly by removing site blockers, a very strong effect at high temperature. This enables unprecedented rates in the TH of phenol at these temperatures.

Electrocatalysis↗

Possible pitfalls in theoretical determination of ground-state crystal structures: The case of platinum nitride

In many theoretical studies of the properties of solids, the first and often crucial step entails the determination of the crystal structure via some form of energy minimization. Here we discuss general potential pitfalls that are often encountered in such calculations. We do so in the context of the classic zinc-blende crystal structure that underlines all octet semiconductors and was more recently invoked to explain nonoctet half-metallic magnets such as CrAs, as well as noble-metal nitrides such as PtN, PdN, and NiN. These pitfalls are related to the way in which mechanical instabilities of assumed structures are identified, discarded, and replaced. Using a more general global space-group optimization (GSGO) approach uncovers different and more complex structures that have much lower energies and do not have mechanical instabilities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Nature of Hydrogen Adsorption on Platinum in the Aqueous Phase

H2 adsorption properties on Pt in aqueous phase was determined by a reaction kinetic measurement of gas H2 reacting with liquid D2O into liquid HDO, gas HD and D2, and a DFT based ab inito molecular dynamic simulation of H2 adsorption on Pt (111) in the presence and absence of water. Both approaches show that the H2 adsorption on Pt in water is much weaker than that in the gas phase. The presence of interfacial water destabilizes the adsorbed H on Pt via decreasing the adsorption heat (hydrogen binding energy) by 19 - 22 kJ·molH2-1 and inducing an extra entropy loss of 50 - 70 J·mol H2-1·K-1. Upon H adsorption on Pt, the closest water layer near Pt surface shifts to a larger distance from the surface and re-orientates to a more ordered structure; in turn, the water layer limits the translation mobility of adsorbed H on Pt. The influence of interfacial water property on H2 adsorption is also reflected by the decrease of adsorption heat with the decrease of local pH provided by the support. Research was funded by the Laboratory Directed Research and Development program at Pacific Northwest National Laboratory.

Yang, Guoju↗