Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NPR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Static tests of the J97 powered, external augmenter V/STOL wind tunnel model

Results of the static testing (zero forward speed) of the J97-powered, external augmentor, large scale, V/STOL model are discussed. With a ground clearance of 7.5 feet, believed to have put the model essentially out of ground effect, a gross thrust augmentation ratio of 1.60 at nozzle pressure ratio (NPR) = 3.0 was measured for the fuselage augmentor. A similar figure was apparent for the wing augmentor. An overall ratio of model thrust to bare engine thrust of 1.52 was determined at NPR = 3.0. The structural integrity of the model was well demonstrated and duct pressure losses were small.

Garland, D. B.↗
NASA NTRS1993

Experimental investigation of spherical-convergent-flap thrust-vectoring two-dimensional plug nozzles

An experimental investigation of multiaxis thrust vectoring nozzles with spherical convergent flaps (SCF) and a convertible (in-flight deployable) centerline plug were tested in the NASA-Langley 16-Foot Transonic Tunnel Static Test Facility. Parameters tested during the static test included plug length, external shroud length, shroud internal angle, and yaw vector angle. Results indicated that the SCF convertible-plug nozzle flow is highly three dimensional and characterized by internal flow separation and shock effects. The resultant thrust and discharge coefficient levels were lower than previous wedge nozzle results. In addition, increasing shroud internal angle increased resultant thrust ratio but decreased discharge coefficient. Increasing shroud length increased resultant thrust ratio performance for NPR's greater than 6.0 but for NPR's less than 6.0, resultant thrust ratio decreased as shroud length increased. Increasing plug length caused an increase in resultant thrust ratio and an increase in discharge coefficient. Increasing geometric yaw vector angle had no effect on resultant thrust ratio and little effect on discharge coefficient.

Cler, Daniel L.↗
NASA NTRS1992

Design and evaluation of single and dual flow thrust vector nozzles with post exit vanes

This Thrust Vectored Research project required that a 1/24 scale model of the F/A-18 High Alpha Research Vehicle, (HARV), propulsion system be constructed on the university campus. This propulsion system was designed for cold flow testing on a multicomponent test rig. Forces and moments were measured to study nozzle performance parameters. The flow visualization technique of color Schlieren photography was performed to investigate the flow phenomena at the nozzle exit. The flow interactions that were identified consisted of vane nozzleing between the outer and lower vanes and vane tip interference. The thrust vectoring system consisted of three asymmetrically spaced vanes installed circumferentially on a maximum afterburner nozzle. The performance of the nozzle was investigated with the outer and lower vanes equally deflected, (-10 deg is less than delta(sub v) is less than 25 deg), and with the upper vane fully retracted, (delta(sub v) equals -10 deg). The nozzle pressure ratio ranged from 4 to 6. The results indicated that a vane nozzleing effect developed at nozzle pressure ratios of 4 and 6 when the outer and lower vanes were deflected far enough into the flow field such that the increase in vane area accelerated the flow past the vanes causing distorted shock waves. This accelerated flow was a result of a pressure differential existing between the inside surface of the vane and the ambient pressure. The stagnation pressure that developed along the inside surface of the vane accelerated the flow past the vanes causing it to equalize with ambient pressure, thus providing distorted shock waves. A tip interference was present at the trailing edge of the upper vane as a result of low nozzle pressure, NPR 4, with high vane deflection, delta(sub v) equals 25 degrees, and also with a high nozzle pressure, NPR 6, and low vane deflections, delta(sub v) equals 15 degrees.

Carpenter, Thomas W.↗
NASA NTRS1995

High speed nozzles task

Supersonic cruise exhaust nozzles for advanced applications are optimized for a high nozzle pressure ratio (NPR) at design supersonic cruise Mach number and altitude. The performance of these nozzles with large expansion ratios are severely degraded for operations at subsonic speeds near sea level for NPR significantly less than the design values. The prediction of over-expanded 2DCD nozzles performance is critical to evaluating the internal losses and to the optimization of the integrated vehicle and propulsion system performance. The reported research work was aimed at validating and assessing existing computational methods and turbulence models for predicting the flow characteristics and nozzle performance at over-expanded conditions. Flow simulations in 2DCD nozzles were performed using five different turbulence models. The results are compared with the experimental data for the wall pressure distribution and thrust and flow coefficients at over-expanded static conditions.

Hamed, Awatef↗
NASA NTRS1996

An experimental and computational investigation of a translating throat single expansion-ramp nozzle

A translating throat single expansion-ramp nozzle (SERN) concept was designed to improve the off-design performance of a SERN with a large, fixed expansion ratio. The concept of translating the nozzle throat provides the SERN with a variable expansion ratio. An experimental and computational study was conducted to predict and verify the internal performance of this concept. Three nozzles with expansion ratios designed for low, intermediate, and high Mach number operating conditions were tested in the Jet-Exit Test Facility at the NASA Langley Research Center. Each nozzle was tested with a concave and a convex geometric expansion ramp surface design. Internal nozzle performance, paint-oil flow and focusing Schlieren flow visualization were obtained for nozzle pressure ratios (NPR's) up to 13. The Navier-Stokes code, PAB3D, with a k-epsilon turbulence model was utilized to verify experimental results at selected NPRs and to predict the performance at conditions unattainable in the test facility. Two-dimensional simulations were computed with near static free-stream conditions and at nozzle pressure ratios of 5, 9, and 13 for the concave ramp, low Mach number configuration and at the design NPR of 102 for the concave ramp, high Mach number configuration. Remarkable similarities between predicted and experimental flow characteristics, as well as performance quantities, were obtained.

Deere, Karen A.↗
NASA NTRS1999

Experimental and Computational Investigation of a Translating-Throat Single-Expansion-Ramp Nozzle

An experimental and computational study was conducted on a high-speed, single-expansion-ramp nozzle (SERN) concept designed for efficient off-design performance. The translating-throat SERN concept adjusts the axial location of the throat to provide a variable expansion ratio and allow a more optimum jet exhaust expansion at various flight conditions in an effort to maximize nozzle performance. Three design points (throat locations) were investigated to simulate the operation of this concept at subsonic-transonic, low supersonic, and high supersonic flight conditions. The experimental study was conducted in the jet exit test facility at the Langley Research Center. Internal nozzle performance was obtained at nozzle pressure ratios (NPR's) up to 13 for six nozzles with design nozzle pressure ratios near 9, 42, and 102. Two expansion-ramp surfaces, one concave and one convex, were tested for each design point. Paint-oil flow and focusing schlieren flow visualization techniques were utilized to acquire additional flow data at selected NPR'S. The Navier-Stokes code, PAB3D, was used with a two-equation k-e turbulence model for the computational study. Nozzle performance characteristics were predicted at nozzle pressure ratios of 5, 9, and 13 for the concave ramp, low Mach number nozzle and at 10, 13, and 102 for the concave ramp, high Mach number nozzle.

Deere, Karen A.↗
NASA NTRS1995

Temperature and Forward Flight Effects on an Underexpanded Jet Noise

An experimental investigation was carried out in the NASA Ames 40'x80' wind tunnel to investigate the far field noise characteristics of a supersonic jet exiting from an axisymmetric convergent nozzle. The nozzle geometry conforms to the ASME specifications for the long radius nozzle. The nozzle pressure ratio NPR, (stagnation pressure/ambient pressure) was varied from 2.5 to 4.5. The temperature ratio, TR (stagnation temperature/ambient temperature) was varied from 2.5 to 3.5. The resulting Reynolds number range, based on the nozzle exit diameter of 12.55cm, is from 0.98 -1.27 x 10(exp 6). The far field directivity was obtained using 1/4 inch diameter condenser microphone with the Flow-Induced Tone Eliminator (FITE) aerodynamic microphone fore body. Appropriate microphone corrections, developed by Allen et al., were made for accurate in-flow acoustic measurements at high frequencies. The narrow band (band width = 64 Hz) frequency spectra covering a range from 0 to 70 KHz were obtained with an accuracy of plus or minus 0.6dB. Typical narrow-band spectra representing far field noise in the forward quadrant, normal to the jet axis and the aft quadrant are shown. The three dominant components of the noise, the screech tone, broad-band shock associated noise and the mixing noise, are clearly identifiable in the spectra. The variation of the screech tone with the exit Mach number (calculated from the isentropic equation relating NPR to Mach number), is shown. The solid line in the figure is calculated using Tam's formula. The model developed by Tam seems to work well even at high temperatures. The appearance of the screech tone is confined to the forward quadrant (theta less than or equal to 60 degrees; the angle theta is measured from the inlet axis). The amplitude of the tone is about 10 dB higher than the broad band noise, which is less than the normally observed amplitude for cold jets operating at similar conditions.

Krothapalli, A.↗
NASA NTRS2002

An Experimental Investigation of the Flow Structure of Supersonic Impinging Jets

An experimental investigation into the jet structure associated with sound production by a supersonic impinging jet is presented. Large plate impinging tones are investigated for a nozzle pressure ratio (NPR) of 4 and nozzle-to-plate spacings between 1 and 5 nozzle exit diameters, where NPR is equal to the ratio of the stagnation pressure to the pressure at the nozzle lip. Results from phase-locked shadowgraph and phase-averaged digital particle image velocimetry (DPIV) studies indicate that, during the oscillation cycle, the Mach disk oscillates axially, a well defined recirculation zone is created in the subsonic impingement region and moves toward the plate, and the compression and expansion regions in the outer supersonic flow move downstream, Sound appears to be generated in the wall jet at approximately 2.6R from the jet axis, where R is the nozzle exit radius. The oscillatory motion in the wall jet is the result of the periodic fluid motion in the near wall region.

Henderson, Brenda↗
NASA NTRS2003

Comparison of Experimental Data and Computations Fluid Dynamics Analysis for a Three Dimensional Linear Plug Nozzle

A three dimensional linear plug nozzle of area ratio 12.79 was designed by EADS Space Transportation (former Astrium Space Infrastructure). The nozzle was tested within the German National Technology Program 'LION' in a cold air wind tunnel by TU Dresden. The experimental hardware and test conditions are described. Experimental data was obtained for the nozzle without plug side wall fences at a nozzle pressure ratio of 116 and then with plug side wall fences at NPR 110. Schlieren images were recorded and axial profiles of plug wall static pressures were measured at several spanwise locations and on the plug base. Detailed CFD analysis was performed for these nozzle configurations at NPR 116 by NASA MSFC. The CFD exhibits good agreement with the experimental data. A detailed comparison of the CFD results and the experimental plug wall pressure data are given. Comparisons are made for both the without and with plug side wall fence configurations. Numerical results for density gradient are compared to experimental Schlieren images. Experimental nozzle thrust efficiencies are calculated based on the CFD results. The CFD results are used to illustrate the plug nozzle fluid dynamics. The effect of the plug side wall is emphasized.

Ruf, J. H.↗
NASA NTRS2003

Comparison of Experimental Data and Computations Fluid Dynamics Analysis for a Three Dimensional Linear Plug Nozzle

A three dimensional linear plug nozzle of area ratio 12.79 was designed by Astrium. The nozzle was tested within the German National Technology Program LION in a cold air wind tunnel by TU Dresden. The experimental hardware and test conditions are described. Experimental data was obtained for the nozzle without plug side wall fences and then with plug side wall fences. Experimental data for two nozzle pressure ratios (NPR), 116 and 45, are presented for the without fence and with fence configurations. Schlieren images of both NPR were recorded. Axial profiles of plug wall static pressures were measured at several spanwise locations and on the plug base. Detailed computational fluid dynamics (CFD) analysis was performed for these nozzle configurations by NASA MSFC. The CFD exhibits good agreement with the experimental data. A detailed comparison of the CFD results and the experimental plug wall pressure data is given for four test conditions; at both NPRs, without and with plug side wall fences. Numerical schlieren images are compared to experimental schlieren images. Nozzle thrust efficiencies are calculated from the CFD results. The CFD results are used to illustrate the plug nozzle fluid dynamics for all four test conditions. The effect of the plug side wall fences at both NPRs is emphasized.

Ruf, J. H.↗
NASA NTRS1999

Experimental Investigation of Convoluted Contouring for Aircraft Afterbody Drag Reduction

An experimental investigation was performed in the NASA Langley 16-Foot Transonic Tunnel to determine the aerodynamic effects of external convolutions, placed on the boattail of a nonaxisymmetric nozzle for drag reduction. Boattail angles of 15 and 22 were tested with convolutions placed at a forward location upstream of the boattail curvature, at a mid location along the curvature and at a full location that spanned the entire boattail flap. Each of the baseline nozzle afterbodies (no convolutions) had a parabolic, converging contour with a parabolically decreasing corner radius. Data were obtained at several Mach numbers from static conditions to 1.2 for a range of nozzle pressure ratios and angles of attack. An oil paint flow visualization technique was used to qualitatively assess the effect of the convolutions. Results indicate that afterbody drag reduction by convoluted contouring is convolution location, Mach number, boattail angle, and NPR dependent. The forward convolution location was the most effective contouring geometry for drag reduction on the 22 afterbody, but was only effective for M < 0.95. At M = 0.8, drag was reduced 20 and 36 percent at NPRs of 5.4 and 7, respectively, but drag was increased 10 percent for M = 0.95 at NPR = 7. Convoluted contouring along the 15 boattail angle afterbody was not effective at reducing drag because the flow was minimally separated from the baseline afterbody, unlike the massive separation along the 22 boattail angle baseline afterbody.

Deere, Karen A.↗
NASA NTRS2005

The Systems Engineering Process for Human Support Technology Development

Systems engineering is designing and optimizing systems. This paper reviews the systems engineering process and indicates how it can be applied in the development of advanced human support systems. Systems engineering develops the performance requirements, subsystem specifications, and detailed designs needed to construct a desired system. Systems design is difficult, requiring both art and science and balancing human and technical considerations. The essential systems engineering activity is trading off and compromising between competing objectives such as performance and cost, schedule and risk. Systems engineering is not a complete independent process. It usually supports a system development project. This review emphasizes the NASA project management process as described in NASA Procedural Requirement (NPR) 7120.5B. The process is a top down phased approach that includes the most fundamental activities of systems engineering - requirements definition, systems analysis, and design. NPR 7120.5B also requires projects to perform the engineering analyses needed to ensure that the system will operate correctly with regard to reliability, safety, risk, cost, and human factors. We review the system development project process, the standard systems engineering design methodology, and some of the specialized systems analysis techniques. We will discuss how they could apply to advanced human support systems development. The purpose of advanced systems development is not directly to supply human space flight hardware, but rather to provide superior candidate systems that will be selected for implementation by future missions. The most direct application of systems engineering is in guiding the development of prototype and flight experiment hardware. However, anticipatory systems engineering of possible future flight systems would be useful in identifying the most promising development projects.

Jones, Harry↗
NASA NTRS2008

The New NASA Orbital Debris Mitigation Procedural Requirements and Standards

NASA has issued major updates to its principal orbital debris mitigation policy directive and standards. The new NASA Procedural Requirements for Limiting Orbital Debris (NPR 8715.6), with its supporting NASA Standard 8719.14, both refine earlier orbital debris mitigation documents and in some areas expand their applicability. Organizational and individual responsibilities along with general directives are set forth in NPR 8715.6. New requirements include routine conjunction assessments for all maneuverable NASA spacecraft in LEO and GEO, prompt notifications of intended or unintended debris generation, preparation and maintenance of formal end-of-mission plans, and disposal of vehicles in operation around the Moon and Mars and at the Earth-Sun Lagrangian points. NASA Standard 8719.14 replaces the 1995 NASA Safety Standard 1740.14 with no major new requirements but with several refinements and additions, some of which had already been adopted. Compliance with human casualty risk limitations from reentering debris will be calculated explicitly and not be expressed in terms of average debris casualty area. Moreover, the minimum kinetic energy threshold for potentially injurious reentering debris is set at 15 Joules. The overarching requirement for the disposal of GEO spacecraft and launch vehicle orbital stages is to ensure that the vehicles do not come within GEO + 200 km for at least 100 km after end of mission, rather than setting specific requirements for the disposal orbit. Spacecraft operating in or routinely transiting LEO must remain in the region for no more than 25 years after end of mission or 30 years after launch, whichever occurs sooner. A comprehensive new NASA handbook on orbital debris has also been prepared to provide background on the orbital debris environment and the related NASA mitigation requirements and standards.

Johnson, Nicholas L.↗
NASA NTRS2009

Human Rating Requirements for NASA's Constellation Program

This slide presentation reviews the human system integration (HSI) process in achieving human ratings for NASA Constellation Program (CxP). The NASA Procedural Requirements (NPR) document that defines the Human Ratings Requirements is NPR 8705.2B. An example of the human rating requirements flow down is given in the handling qualities for space craft control.

Berdich, Debbie↗
NASA NTRS2009

Bayesian Inference for NASA Probabilistic Risk and Reliability Analysis

This document, Bayesian Inference for NASA Probabilistic Risk and Reliability Analysis, is intended to provide guidelines for the collection and evaluation of risk and reliability-related data. It is aimed at scientists and engineers familiar with risk and reliability methods and provides a hands-on approach to the investigation and application of a variety of risk and reliability data assessment methods, tools, and techniques. This document provides both: A broad perspective on data analysis collection and evaluation issues. A narrow focus on the methods to implement a comprehensive information repository. The topics addressed herein cover the fundamentals of how data and information are to be used in risk and reliability analysis models and their potential role in decision making. Understanding these topics is essential to attaining a risk informed decision making environment that is being sought by NASA requirements and procedures such as 8000.4 (Agency Risk Management Procedural Requirements), NPR 8705.05 (Probabilistic Risk Assessment Procedures for NASA Programs and Projects), and the System Safety requirements of NPR 8715.3 (NASA General Safety Program Requirements).

Dezfuli, Homayoon↗
NASA NTRS2010

The Successful Implementation of NASA Orbital Debris Requirements for the Retirement of TDRS-1

TDRS-1 was decommissioned on October 28th 2009 following more than 26 years of operation. The Grand Old Dame of the TDRSS constellation wa s launched aboard the maiden voyage of the Space Shuttle Challenger ( STS-6) in April 1983. TDRS-1 survived a malfunction of the Inertial Upper Stage eventually utilizing its own propulsion system to success fully reach its assigned station in geosynchronous orbit. The anomalo us beginning of the TDRS-1 mission was not without lasting consequenc es as the primary reaction control system (A-side) was completely di sabled with an apparent propellant leak and the secondary system (B-s ide) suffered damage to its negative roll thruster rendering the thru ster inoperable. Following decommissioning the challenge to completin g a successful TDRS-1 end-of-mission (EOM) was the implementation of the stringent orbital debris requirements of NPR 8715.6 with a parti ally functioning spacecraft not originally designed to meet those req uirements. The TDRS-1 EOM had three key goals: 1) removal of the spac ecraft from geosynchronous orbit; 2) depletion of the remaining prope llant; and 3) passivation of all other sources of energy storage or generation. The TDRS-1 EOM approach was one of minimizing risks while accomplishing the goals above. The orbit raising portion of EOM was accomplished using deltavelocity operations already proven during pre vious stationchanging maneuvers. The propellant depletion approach wa s necessarily more aggressive as over 20 hours of burn time was requ ired to deplete the remaining fuel. A novel approach utilizing a spin ning, thrusting, passively controlled spacecraft configuration was ut ilized to achieve reasonable burn durations that met schedule constra ints. This nonstandard configuration required careful analysis of ele ctrical, thermal, and communication subsystems. The configuration wa s thoroughly simulated prior to the start of operations and carefully characterized during the initial spin period and first burn. Passiva tion was by definition a unique operation not previously performed wi thin the TDRS 1-7 constellation. Use was made of a TDRS spacecraft si mulator to verify the operational procedure to mitigate risks and pro vide crew training. TDRS-1 orbit raising maneuvers commenced on June 5th 2010 and completed on June 14th with an apogee 370 km and a peri gee 352 km above geosynchronous altitude. 127 kg of propellant were e stimated to be remaining in the tanks at the completion of orbit rais ing. TDRS-1 was placed in its spinning orientation on June 16th and the first fuel depletion burn was performed the following day. A seri es of 10 depletion burns were performed ending on June 26th when both propellant tank pressures experienced dramatic drops. Final passivat ion was performed on June 27 th deactivating electronics, removing t he batteries from the bus and solar arrays, and disabling the space-t o-ground communications equipment. The Second TDRS Ground Terminal (S TGT) continued to open loop track TDRS-1 for several days attempting command reacquisition several times a day. All attempts were unsucce ssful confirming passivation was achieved. The TDRS-1 orbit at passiv ation was an orbital debris compliant 36,319 x 36,128 km in height. W hile differing spacecraft designs may preclude mimicking the exact TD RS-1 EOM approach, the TDRS-1 campaign serves to demonstrate that pr e-NPR 8715.6 designs can be made to meet the requirements resulting i n a reduced orbit debris environment for future missions

Mirczak, Walter↗
NASA NTRS2011

Innovative Approach Enabled the Retirement of TDRS-1 Compliant with NASA Orbital Debris Requirements

The first Tracking and Data Relay Satellite (TDRS-1) was deactivated on June 27th 2010 following more than 26 years of operation. The end-of-mission (EOM) operations were developed to address the stringent requirements of NPR 8715.6: NASA Procedural Requirements for Limiting Orbital Debris, which consists of three key items: 1) removal from the geosynchronous arc; 2) depletion of the remaining propellant; and 3) passivation of all sources of energy storage or generation [1]. The EOM approach minimized risks while accomplishing these goals. Raising TDRS-1 over 350 km above geosynchronous was accomplished via proven station change operations. Depleting propellant was the most challenging task, requiring over 20 hours of thruster on-time accumulated within schedule, orbit, and spacecraft subsystem constraints. The attitude configuration and operational procedures, including the unique final passivation method, were thoroughly analyzed and simulated prior to the start of operations. The complete EOM campaign lasted 21 days. The TDRS-1 EOM campaign demonstrated that pre-NPR 8715.6 satellite designs can be made to comply and that lessons learned could be applied to other satellite designs. The significant TDRS-1 effort demonstrates a commitment by NASA to responsible orbital debris management in compliance with international standards.

Zaleski, Ronald↗
NASA NTRS2011

Exhaust Nozzle Plume Effects on Sonic Boom Test Results for Isolated Nozzles

Reducing or eliminating the operational restrictions of supersonic aircraft over populated areas has led to extensive research at NASA. Restrictions were due to the disturbance of the sonic boom, caused by the coalescence of shock waves formed off the aircraft. Recent work has been performed to reduce the magnitude of the sonic boom N-wave generated by airplane components with focus on shock waves caused by the exhaust nozzle plume. Previous Computational Fluid Dynamics (CFD) analysis showed how the shock wave formed at the nozzle lip interacts with the nozzle boat-tail expansion wave. An experiment was conducted in the 1- by 1-ft Supersonic Wind Tunnel at the NASA Glenn Research Center to validate the computational study. Results demonstrated how the nozzle lip shock moved with increasing nozzle pressure ratio (NPR) and reduced the nozzle boat-tail expansion, causing a favorable change in the observed pressure signature. Experimental results were presented for comparison to the CFD results. The strong nozzle lip shock at high values of NPR intersected the nozzle boat-tail expansion and suppressed the expansion wave. Based on these results, it may be feasible to reduce the boat-tail expansion for a future supersonic aircraft with under-expanded nozzle exhaust flow by modifying nozzle pressure or nozzle divergent section geometry.

Castner, Raymond S.↗